DMX Operator 1610 - Console de contrôle d'éclairage Eurolite - Free user manual and instructions

Product Type	DMX Lighting Controller
Model	DMX Operator 1610
Brand	Eurolite
DMX Channels	16
Number of Fixtures	10
DMX Protocol	DMX512
Control Mode	Manual / Sound Active / Auto
Display	Backlit LCD Screen
Power Supply	9V DC, 500mA (external adapter)
Dimensions (W x D x H)	approx. 483 x 133 x 89 mm (19" rack)
Weight	approx. 1.5 kg
Housing Material	Metal with plastic front panel
DMX Connectors	3-pin XLR (male/female)
Fader Controls	16 channel faders + master fader
Button Controls	Scene, Chase, Blackout, Tap Sync
Sound Control	Built-in microphone with sensitivity adjustment
Scene Storage	Up to 10 scenes
Chase Sequences	Up to 10 chases with adjustable speed
Security Features	Kensington lock slot
Maintenance	Keep dry, clean with soft cloth, avoid solvents
Spare Parts / Repairability	No user-serviceable parts; contact Eurolite service
General Information	Designed for professional lighting control; compatible with most DMX fixtures

Frequently Asked Questions - DMX Operator 1610 Eurolite

How do I connect the DMX Operator 1610 to my fixtures?

Use a standard 3-pin DMX cable from the controller's DMX OUT to the first fixture's DMX IN, then daisy-chain to additional fixtures. Ensure terminator is used on last fixture.

Can I control moving heads with this controller?

Yes, the DMX Operator 1610 can control any DMX512 compatible moving head or dimmer. Each fixture uses up to 16 channels depending on its mode.

How do I store a scene?

Set the faders to desired positions, then press and hold the Scene button (1-10) for 2-3 seconds until the LED blinks and stays on, confirming save.

What is the power requirement?

The controller requires a 9V DC, 500mA power adapter (included). Using a different adapter may damage the unit.

How do I enable sound-activated mode?

Press the Sound Active button; the built-in microphone will trigger chase sequences according to music. Adjust sensitivity via the rear panel control.

Can I run multiple chases at once?

The controller can play one chase at a time across all fixtures. You can manually override channels with faders when chase is active.

How do I reset the controller?

Turn the unit off and on. If unresponsive, press the Blackout button twice quickly to clear any hold. No factory reset option exists.

What type of display does it have?

It features a backlit LCD screen that shows channel values, scene/chase status, and mode.

Is the controller rack-mountable?

Yes, it has standard 19-inch rack ears and fits a 2U height. Ensure proper ventilation.

How do I clean the DMX Operator 1610?

Disconnect power, use a soft, dry cloth to wipe the surface. Do not use water or chemical cleaners.

USER MANUAL DMX Operator 1610 Eurolite

Compact console for 16 lighting effect units up to 10 DMX channels and USB

No. 70064522

www.eurolite.de

INHALT

EINFÜHRUNG 3

Produktmerkmale 3

www.eurolite.de

www.youtube.com/eurolitevideo

www.facebook.com/Eurolitefans

IMPORTANT SAFETY INSTRUCTIONS .... 13

OPERATING ELEMENTS AND CONNECTIONS . 14

SETUP 15

DMX512 connection 15

Adjusting the DMX start addresses on the fixtures 15

Power supply 15

OPERATION 16

Enabling programming mode 16

Programming scenes 16

Programming chases 16

Playing chases 17

Strobe effect 18

Blackout 18

Data backup 18

Data import 18

Firmware update 19

Reset to factory settings 19

CLEANING AND MAINTENANCE 19

TECHNICAL SPECIFICATIONS .... 19

D00117017, version 1.0, publ. 24/05/2018

For product updates, documentation, software and support please visit www.eurolite.de. You can find the latest version of this user manual in the product's download section.

© 2018 Eurolite. All rights reserved.

No part of this document may be reproduced in any form without the written permission of the copyright owner. The contents of this document are subject to revision without notice due to continued progress in methodology, design, and manufacturing. Eurolite shall have no liability for any error or damage of any kind resulting from the use of this document.

All trademarks mentioned herein are the property of their respective owners.

INTRODUCTION

Experience Eurolite.

Product videos, suitable accessories, firmware and software updates, documentation and the latest news about the brand. You will find this and much more on our website. You are also welcome to visit our YouTube channel and find us on Facebook.

www.eurolite.de

www.youtube.com/eurolitevideo

www.facebook.com/Eurolitefans

Welcome to Eurolite! Thank you for choosing one of our products. Eurolite is your connection to the world of show with an unparalleled variety of products, both for professionals and beginners.

If you follow the instructions given in this manual, we are sure that you will enjoy this product for a long period of time. This user manual will show you how to install, set up and operate your new Eurolite product.

Users of this product are recommended to carefully read all warnings in order to protect yourself and others from damage. Please keep this manual for future needs and pass it on to further owners.

Product features

• 160 control channels for 16 fixtures with up to 10 channels
• USB port for storing program data
• 16 programmable scenes
- 16 programmable chases with 200 scenes each can be stored
- Manual, time-controlled or sound-controlled chase running mode
- Fade between scenes adjustable between 0-30 s
• 2 DMX fixture levels can be controlled
- 5 DMX channel faders
- Blackout and strobe function
- Sound control via built-in microphone with adjustable sensitivity
- LED display
- 3-pin XLR connector
- Firmware update via USB

IMPORTANT SAFETY INSTRUCTIONS

CAUTION!

Operating conditions

This device has been designed for indoor use only. Keep this device away from rain and moisture.

DANGER!

Electric shock caused by short-circuit

Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires!

• Please read these operating instructions carefully before using the product. They contain important information for the correct use of your product. Please keep them for future reference.
• Only use the product according to the instructions given herein. Damages due to failure to follow these operating instructions will void the warranty! We do not assume any liability for any resulting damage.
• We do not assume any liability for material and personal damage caused by improper use or non-compliance with the safety instructions. In such cases, the warranty/guarantee will be null and void.
• Unauthorized rebuilds or modifications of the product are not permitted for reasons of safety and render the warranty invalid.
• Never open any part of the product to prevent a possible electric shock.
• IMPORTANT: This product is not an outdoor product! Only for indoor use! Do not use this device near water. The recommended temperature range is -5 to +45 °C.
• To clean the unit, disconnect it from the power source.
• Only use a soft cloth, never use any solvent.
• Do not touch the power cord and connectors with wet hands as it may cause electric shock.
• This product is not a toy. Keep it out of the reach of children and pets. Do not leave packaging material lying around carelessly.
• This unit corresponds to all required directives of the EU and is therefore marked with .

Intended use

The DMX Operator 1610 serves for operation of DMX-controlled lighting effect devices in discotheques or on stage.

Disposal of old equipment

When to be definitively put out of operation, take the product to a local recycling plant for a disposal which is not harmful to the environment. Devices marked with this symbol must not be disposed of as household waste. Contact your retailer or local authorities for more information. Remove any inserted batteries and dispose of them separately from the product.

You as the end user are required by law (Battery Ordinance) to return all used batteries/rechargeable batteries. Disposing of them in the household waste is prohibited. You may return your used batteries free of charge to collection points in your municipality and anywhere where batteries/rechargeable batteries are sold. By disposing of used devices and batteries correctly, you contribute to the protection of the environment.

OPERATING ELEMENTS AND CONNECTIONS

No.	Element Function
1	Button group FIXTURE	Buttons 1-16 to select and deselect devices. The LEDs indicate which devices are selected.
2	Button group SCENE	Buttons 1-8 to select and deselect scenes. The memory banks are split into 2 pages which can be selected with the corresponding PAGE button. The control LEDs next to the button indicate which page is selected.
3	Button group CHASE	Buttons 1-8 to select and deselect chases. The memory banks are split into 2 pages which can be selected with the corresponding PAGE button. The control LEDs next to the button indicate which page is selected.
4	Display Shows the current DMX value or activity.
5	USB port	To connect a USB drive for data backup, import of data and firmware updates.
6	Sliding faders 1-10 For adjusting	the DMX values of the connected lighting effect units. The current DMX value is indicated in the display. The controls are split into 2 pages so that 2 x 5 DMX channels can be controlled per fixture.
7	Sliding fader WAIT TIME	To adjust the running speed when a chase is running in time-controlled mode (0.1s – 10 min).
8	Sliding fader FADE TIME	To adjust the fading speed between two scenes when the illumination scene in a memory bank or a chase is running in time-controlled mode or sound control mode (0-30 s).
9	Sliding fader STROBE SPEED	To adjust the flash rate of the strobe effect.
10	Button PAGE	To switch the faders (6) between the two pages 1-5 and 6-10. The control LEDs indicate which channel group is selected.

11	Button EDIT/REC To call programming mode and confirm settings.
12	Button INSERT/TAP To insert a scene into a chase. Press twice to set the running speed for the chase
13	Button DEL/CLR To delete scenes and chases.
14	Buttons UP and DOWN To switch between menu items and adjust values.
15	Button RUN MODE To switch between manual, sound control and time-controlled mode.
16	Button BLACK OUT Sets all control channels to the value zero (e.g. for turning off the devices).
17	Button STROBE Activates strobe effect.
18	DMX512 output 3-pin XLR jack for connection with DMX input port of the first fixture.
19	Power input Plug in the mains cable of the supplied power unit here.
20	Power on/off To switch on/off the device.

SETUP

Create all connections while the device is switched off. Use the shortest possible high-quality DMX cables for all connections. Install the device on a plane surface.

DMX512 connection

Connect the DMX output of the DMX Operator 1610 to the DMX input of the first fixture. Then connect the DMX output of the first fixture in the DMX chain to the DMX input of the next fixture. Always connect one output to the input of the next fixture until all fixtures are connected. For long connection cables it is recommended to terminate the DMX line. Plug a terminating plug with a 120 resistor between signal (-) and signal (+) to the DMX output of the last unit. If the cable length exceeds 300m or the number of DMX devices is greater than 32, it is recommended to insert a DMX level amplifier to ensure proper data transmission.

Pin connection:

DMX-output XLR mounting-socket:

DMX-input XLR mounting-plug:

Adjusting the DMX start addresses on the fixtures

Adjust the DMX start addresses on your fixtures according to the table below, i.e. a multiple of 10 + 1. If identical fixture groups are to be controlled synchronously, set them to the same start address; otherwise each fixture must receive an individual address. For further information, please refer to the fixture's documentation.

Fixture	Start address	Fixture	Start address
1	1	6	51
2	11	7	61
3	21	8	71
4	31	9	81
5	41	10	91

Power supply

Connect the power adapter provided to the corresponding input on the controller and to a mains socket. Turn on the unit with the power switch. After the operation, turn off the unit and disconnect the mains plug of the power adapter from the socket, to prevent unnecessary power consumption.

OPERATION

The controller uses three different operation modes: Manual, Auto and Sound Control. When you switch on the device, it will automatically operate in the previously used mode (if it was active for at least 10 seconds before the device was switched off). Use the RUN MODE button (15) to select the operating mode. The LEDs MANUAL, AUTO and MUSIC indicate the current setting.

Enabling programming mode

In order to program light, switch to programming mode. For this, keep the EDIT/REC button pressed until the LED next to the button lights. To switch off the programming mode keep pressing the EDIT/REC button again until the LED goes out.

Programming scenes

Manual adjustment of a scene

1. Use the buttons FIXTURE 1-16 to select the units to be controlled. The corresponding LEDs of the buttons light. If a button is pressed once again, the corresponding fixture is deselected.
2. Adjust the desired DMX values for the DMX channels using the faders. As soon as a fader is moved, the display indicates the current output value as a DMX value.
3. The 10 control channels are combined in 2 groups (channel pages) of 5 channels each. If necessary, use the button PAGE (10) to switch between the two channel groups 1-5 (red LED lights) and 6-10 (green LED lights), until the desired values are assigned to all channels.

Memorizing scenes

16 memory banks are available for scenes.

1. Enable programming mode.
2. Adjust a scene (see above).
3. Shortly press EDIT/REC.

4. Exit programming mode.

5. Use one of the buttons SCENE 1-8 to select the desired memory location. The memory banks are split into 2 pages. If necessary, use the PAGE button to switch between the pages. The control LEDs next to the button indicate which page is selected. To confirm the memory procedure, all LEDs of the controller flash three times.

6. Repeat the steps 2 to 4 to memorize further scenes.

Deleting scenes

1. Enable programming mode.
2. Keep DEL/CLEAR pressed. Now additionally press the SCENES button of the scene you want to delete. To confirm the deleting procedure, all LEDs of the controller flash three times.
3. Exit programming mode.

Programming chases

The scenes previously memorized can be compiled to a chase (scene sequence) in any desired order and memorized. 16 memory banks are available. A sequence of up to 200 steps can be programmed on each memory bank. Chases may run manually, sound-controlled or time-controlled.

1. Enable programming mode.
2. Use one of the buttons CHASE 1-8 to select the desired memory location. The memory banks are split into 2 pages. If necessary, use the PAGE button to switch between the pages. The control LEDs next to the button indicate which page is selected. To confirm the memory procedure, all LEDs of the controller flash three times.
3. Adjust the desired scene or select it form a memory location that contains scenes (see also section programming scenes).
4. Shortly press EDIT/REC. To confirm the memory procedure, all LEDs of the controller flash three times.
5. Repeat the steps 3 and 4 to memorize further scenes.
6. Exit programming mode.

Inserting a step

It is possible to insert scenes before the current editing position.

1. Enable programming mode.
2. Select the chase you want to add a step to with one of the CHASE buttons.
3. Press the INSERT/TAP button (corresponding LED flashes). Now, a scene can be inserted before the current editing position.
4. Use the buttons ◀ and ▶ to jump from one step to the next. The display indicates the current editing position.
5. Adjust the desired scene or select it form a memory location that contains scenes.
6. Shortly press EDIT/REC to memorize the revised chase. To confirm the memory procedure, all LEDs of the controller flash three times.
7. Exit programming mode.

Deleting a step

It is possible to delete a scene from a chase at the current editing position.

1. Enable programming mode.
2. Select the chase you want to add edit with one of the CHASE buttons.
3. Use the buttons ◀ and ▶ to select the step to be deleted.
4. Press the button DEL/CLEAR to delete. To confirm the deleting procedure, all LEDs of the controller flash three times.
5. Exit programming mode.

Deleting chases

1. Enable programming mode.
2. Keep DEL/CLEAR pressed. Now additionally press the CHASE button of the chase you want to delete. To confirm the deleting procedure, all LEDs of the controller flash three times.
3. Exit programming mode.

Playing chases

A chase must be programmed before you can call it. Chases can be played manually, time-controlled or sound-controlled. Use the RUN MODE button (15) to select the operating mode. The LEDs MANUAL, AUTO and MUSIC indicate the current setting. It is possible to select up to 16 chases simultaneously. They are played one after the other. The control LED of the chase currently playing flashes, the others light.

Manual mode

1. Switch to manual mode with the RUN MODE button.
2. Call the desired chase with the CHASE buttons. Press the button again to stop the chase.
3. Use the buttons ◀ and ▶ to jump from one step to the next
4. Use the FADE TIME control to set the fading time of the current scene.

Automatic mode

In automatic mode, the scenes stored in a memory bank will be played time-controlled in a loop. The number of repetitions is adjustable.

1. Switch to automatic mode with the RUN MODE button.
2. Call the desired chase with the CHASE buttons.
3. Use the control WAIT TIME to adjust the running speed and the control FADE TIME to adjust the fade time. Repeatedly press INSERT/TAP for a more precise input of the running speed. The interval of the last two respective keystrokes defines the speed.
4. Use the buttons ◀ and ▶ to adjust the number of repetitions for the chase.

Sound-controlled mode

In sound-control mode, the scenes stored in a memory bank will be synchronized with music pulses via the internal microphone.

1. Switch to sound-controlled mode with the RUN MODE button.
2. Call the desired chase with the CHASE buttons.
3. The sensitivity of the sound control is adjustable between 0-100 % with the buttons ◀ and ▶.
4. Use the FADE TIME control to adjust the fade time.

Strobe effect

By keeping the STROBE button (17) pressed you activate the strobe effect. The green LED lights up. Strobe can be used in all modes and means that the fixtures start to flash. You can adjust the speed with the fader (9).

Blackout

The BLACKOUT button (16) remains active in each mode. If you press (16) all fixtures go out (standby mode). The LED of the button flashes. You can go back to the previous state by pressing the Blackout button again.

Data backup

All settings of a light show, i.e. DMX settings, scenes and chases can be stored on a USB memory device and recalled later. 16 memory banks on the buttons FIXTURE 1-16 are available.

1. Connect a USB memory device to the controller's USB port.
2. Keep the button RUN MODE pressed and simultaneously press the button ◀. The display indicates "Save".
3. Select a memory bank with one of the FIXTURE buttons.
   Each memory bank must be stored separately. If the control LED of a FIXTURE button lights, this memory bank has been stored on the USB memory device before.
   The data will be stored in the folder "led_operator" located on the root directory of the USB memory device. A file with the extension "PRO" will be created for each memory bank. You should not make any changes to the default folder. Otherwise the controller cannot the reload the data later.
4. After completing the data backup (approx. 20 seconds), the display shortly inserts "ok".
5. Turn the controller off and on again. The data backup procedure is complete.

Data import

1. Connect a USB memory device to the controller's USB port.
2. The files to be imported must be stored in the folder "led_operator" located on the root directory of the USB memory device.
3. Keep the button RUN MODE pressed and simultaneously press the button ▶. The display indicates "Load".
   The control LED of a FIXTURE button lights, when data is available on the USB memory device for this memory bank.
4. Select the file to be loaded with the FIXTURE buttons.
5. After successful completion of the data import, the display shortly inserts "ok".
6. Turn the controller off and on again. The data import procedure is complete.

Firmware update

The internal software (firmware) of the controller can be updated. New versions of the firmware will include new features, bug fixes and the optimization of current processes. We suggest to always operating the device with the latest firmware to ensure the highest level of functionality. Check www.eurolite.de from time to time for further information. The installation procedures may vary slightly from those described in this user manual; please note the instructions that will be included in the download package. Follow the steps below to update the firmware:

1. Download the firmware from the internet → www.eurolite.de → download section of the product.
2. Create a folder "led_operator" on the root directory of a USB memory device.
3. Copy and extract the firmware to the folder on the USB memory device.
4. Connect the USB memory device with the new firmware to the controller's USB port.
5. Keep the three buttons EDIT/REC, DEL/CLEAR and ◀ pressed simultaneously and switch on the controller.
6. Keep the buttons pressed until the display indicates "UP--". Then press any button to start the update procedure.
7. As soon as the new firmware has been programmed, the display shortly inserts "ok". Turn the controller off and on again. The update procedure is complete and the USB memory device can be removed

Reset to factory settings

1. Turn off the controller.
2. Keep the three buttons EDIT/REC, RUN MODE and DEL/CLR pressed simultaneously and switch on the controller.
3. The display shortly indicates "Rest" and then "ok" as soon as the factory settings are loaded.

CLEANING AND MAINTENANCE

The product is maintenance-free, except for occasional cleaning. You can use a lint-free, slightly dampened cloth for cleaning. Refer all servicing to qualified personnel.

TECHNICAL SPECIFICATIONS

Power supply:	100-240 V AC, 50/60 Hz via included power adapter (9 V/800 mA)
Power consumption:	<10 W
Number of control channels:	160
Storable scenes:	16
Storable chases:	16 with 200 steps each
Sound-control:	via built-in microphone or audio input
DMX512 output:	3-pin XLR connector
Dimensions (L x W x H):	140 x 310 x 75 mm
Weight:	1.5 kg

Specifications are subject to change without notice due to product improvements.