GT-LS12-UK - Lighting Oecolux - Free user manual and instructions

Product Type	Cordless LED Workshop Lamp
Model	GT-LS12-UK
Battery Type	Lithium-Ion rechargeable
Battery Voltage	3.7 V
Battery Capacity	1800 mAh
LED Output	Max 2.5 W
Input Voltage (Lamp)	12 V DC, max 500 mA
Power Supply Model	LY06-120-0500B
Power Supply Input	100-240 V AC, 50/60 Hz
Car Adapter Model	ZZ-103
Car Adapter Fuse	F0.5AL250V (0.5 A, 250 V)
Charging Time	Approx. 6 hours
Mounting Options	Magnetic base and fold-out hook
Charging Indicator	Red LED while charging, green when fully charged
Protection Class	IP20 (indoor use only)
Usage	Private, indoor; not for commercial workshops
Cleaning	Use a slightly damp cloth with mild detergent; do not immerse
Safety Features	Overcharge protection, short-circuit protection
Warranty	3 years from date of purchase
Repairability	Battery and LEDs not replaceable by user; power supply must be replaced by same type
Disposal	Remove battery before disposal; do not dispose with household waste

Frequently Asked Questions - GT-LS12-UK Oecolux

How long does it take to fully charge the lamp?

The charging time is approximately 6 hours. The LED indicator turns green when fully charged.

Can I use the lamp while charging?

Yes, the LEDs can be switched on during the charging process.

What should I do if the car adapter doesn't work?

Check the fuse in the car cigarette lighter adapter. If blown, replace it with a new fuse of type F0.5AL250V (0.5 A, 250 V).

Is the lamp suitable for commercial workshop use?

No, the lamp is designed for private use only and is not intended for commercial workshops or motor vehicle workshops.

How should I clean the lamp?

Use a well wrung-out, slightly dampened cloth with some dishwashing detergent. Do not use abrasive cleaners or immerse the lamp in water.

Can I replace the battery myself?

No, the rechargeable battery is not replaceable by the user. It can only be removed for disposal by a competent person following the instructions in the manual.

What does the red/green LED indicate?

The red LED indicates the lamp is charging. Once charging is complete, the LED turns green.

How do I dispose of the lamp at the end of its life?

Do not dispose of it with household waste. Remove the rechargeable battery (see manual) and take the lamp to a collection center for electrical and electronic waste. Dispose of the battery according to local regulations.

What is the warranty period?

The warranty period is 3 years from the date of purchase. Keep the receipt and warranty card for claims.

Can I use the lamp in a 24V vehicle?

No, the car cigarette lighter adapter is only suitable for 12 V battery systems. Do not use in trucks or boats with 24 V systems.

USER MANUAL GT-LS12-UK Oecolux

The following table is provided in the image.

in the World

АГИЕ НАЛАЗУРРО

1. 10.13.12.14

2. 公司、公司

Denomination of components ......

Introduction

designated use

1. Fota Indonesia

Safety instructions

128 11

Clearing

Technical data

Dermans archomorphic balloon:

prior to disposal....

MAYEY COOL

Warranty card

Maturity conditions

Scope of delivery/

Denomination of components

1 Cordless LED Workshop Lamp
AC/DC power supply unit
3 Car cigarette lighter adapter
A. Subper lip
B Socket

6 On/off switch
LED
3 12+EFo
2. Look-cut book
10. Hervine
1. 2017年
the right transfer authority

Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly. In the event of product failure within it's intended use over the course of the first 3 years after date of purchase, we will remedy the problem as quickly as possible once it has been brought to our attention. In the unlikely event of such an occurrence, or if you require any information about the product, please contact us via our helpline support services, details of which are to be found both in this manual and on the product itself.

These User Manual can also be downloaded from our website as a PDF file at www.gt-support.de.

Don't look directly into the LEDs during operation!

Introduction

In order to always guarantee the optimum function and performance of this device and to ensure your personal safety, we have one request:

Please read through these user guide carefully prior to initial use and especially follow the safety instructions!

All activities on and with this device may only be carried out as described in these user guide.

If you should pass the work lamp on, please include the user guide.

AFTER SALES SUPPORT

GB 0800 / 328 6020

00800 / 4467 5888

[e-mail]

Cordless LED Workshop Lamp Designated use

Designated use

The device is designed for private use.

The work lamp is not designated for commercial use in motor vehicle workshops or other workshops, etc.

This car cigarette lighter adapter is only suitable for use in motor vehicles provided with a battery voltage of 12 V.

It is not designed for trucks, boats or similar with a battery voltage of 24 volts.

Safety instructions

General instructions

- This product is not to be used by children. This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Do not leave persons requiring assistance to use electrical devices unsupervise The power supply unit must be kept out of the reach of children.

• Packaging materials such as fi lms or polystyrene are not children's toys! Keep children away from them. Suffocation hazard!

• The lamp must not be used in an environment that is subject to a fire and explosion hazard.

• The light is very bright. Never look directly into it at close range and do not shine it into the eyes of people or animals.
• Protect the work lamp from intense heat, cold and strong vibrations and impact.

Cordless LED Workshop Lamp Safety instructions

• In order to avoid damage to surfaces, do not slide the work lamp over the surface to which it is adhered.
• Do not clean the appliance with harsh, scratching or abrasive detergents. The surfaces could otherwise be damaged.

With use in motor vehicles

- The work lamp and the charging cable must not endanger the driver and

passengers. The lamp must always be stored and fastened, so that it also does not create an injury hazard when braking suddenly.

• While driving, all vehicle parts (pedals, steering wheel, etc.) must be capable of being operated by the driver with ease and without any restriction.
• You must not operate the lamp while you are actively driving in traffic and e.g. are turning a steering wheel. Risk of glare!

Hazard from electricity

• Only touch the device with dry hands!
• Use power supply and Lamp only in dry interior rooms.
• The device must not be exposed to dripping or spray water.

• The work lamp and power supply unit must not be immersed in water or other liquids.

• Electrical shock hazard! Therefore, also do not use the appliance in the vicinity of moisture sources, e.g. in the bathroom.

• If the appliance should fall into water or another liquid, first disconnect the power plug and then remove the appliance!
• Only connect the power supply unit to a properly installed socket, with voltage corresponding to the “technical data”.

Cordless LED Workshop Lamp Safety instructions

• When using an adapter plug or extension cord, these must comply with the valid safety regulations. The specified maximum voltage must not be exceeded.
• Ensure that the socket is easily-accessible, so that you can remove the power supply unit, if necessary.

• Lay the power cable to that it does not become a trip hazard.

• Do not use the lamp:

• if it is damaged,
• if the charging cable is damaged,
• the power supply unit or car cigarette lighter adapter is damaged.
• Unwind the charging cable completely prior to use. In doing so, ensure that the charging cable is not trapped, squeezed or damaged by sharp edges or hot items.

- Disconnect the power supply unit from the socket:

• if you are not charging the appliance,
• after each use,
  – before cleaning or putting the appliance away,
• if an obvious fault occurs during operation,
• in a thunder storm.

Always pull on the power supply unit, not on the cable.

• Do not carry or pull the device using the electric cables.
• Do not make any changes to the work lamp, to the power supply unit/cable or on the cigarette lighter adapter.
• Never attempt to open the device or penetrate it with metal objects. Rechargeable batteries and LEDs are not replaceable by operator.
• The workshop lamp and connecting lines can't be repaired or replaced, the workshop lamp has to be disposed accordingly in case of a damage.

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

- If the power supply unit or charging cable is damaged, it must no longer be used and must be replaced by the same type of power supply unit.

Fire hazard

• Do not leave the work lamp unattended when it is being charged.
• Keep the work lamp away from fl ammable materials.
• Do not cover the work lamp or the power supply unit with items.

- A rechargeable battery that has been removed for disposal must not be damaged. Fire hazard from self-combustion!

Risk of property damage

- Do not use the work lamp for longer than 3 hours. As soon as the brightness of the LEDs has noticeably declined, the work lamp must be charged.

- Operating the work lamp until the LEDs have extinguished leads to deep

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

discharge of the rechargeable battery. This can cause the rechargeable battery to be irrecoverably destroyed.

• Also always ensure that you switch off the work lamp.
• Charge the work lamp prior to longer periods of disuse.

Warnings and safety information for the use of products with lithium-ion batteries

The rechargeable batteries in the lamp cannot be exchanged or replaced. They are also not permitted to be used for operating other devices, or recharged through other devices.

A lack of attention when using the product in combination with

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

the warnings below could lead to malfunction, electrical problems, excessive heat, FIRE, injury and/or material damage.

• The light may only be charged with the power supply unit supplied or with the car cigarette lighter adapter.
• The device may only be charged under supervision.

• After the device has been charged, always disconnect the light from the battery charger and allow it to cool down before use.

• Lithium-ion batteries are mechanically sensitive. They can ignite due to an internal short circuit and when coming into contact with air.

• A damaged lithium-ion battery, e.g. because the light is damaged, can ignite 30 or more minutes later.
• Lithium-ion batteries must never be short circuited. A battery removed for disposal can ignite due to a short circuit.
• A burning battery must not be extinguished using water, but rather with sa

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

Disposal

- Also dispose of the packaging materials properly and in an environmentally sound manner. These are raw materials and can be recycled.

Batteries and rechargeable batteries are not permitted to be disposed of with household waste!

- Every consumer is legally obligated to submit batteries and rechargeable

batteries to the collection centre of his local municipality, district or to retailers. All batteries and rechargeable batteries can thereby be disposed of in an environmentally friendly manner.

If the device can no longer be used, submit it to a collection centre for electrical and electronic waste.

Do not dispose of it with household waste.

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

Prior to the disposal of the work lamp, the rechargeable battery must be removed, please refer to “Remove rechargeable battery prior to disposal”.

Damaged rechargeable batteries must be disposed of in accordance with the valid regulations and ordinances.

• Keep removed batteries away from children, do not throw into fire, short circuit or dismantle.
• If battery liquid has leaked, avoid contact with skin, eyes and mucous membranes. When coming into contact with battery acid, immediately rinse the affected areas with plenty of clean water and immediately contact a physician.

Cordless LED Workshop Lamp Safety instructions

- If you suspect a battery to have been swallowed, seek immediate medical attention.

CE Conformity Declaration

The conformity of the product with the legally prescribed standards is guaranteed. You can find the full conformity declaration on the Internet at www.gt-support.de.

Cordless LED Workshop Lamp Use

Use

Recharge battery

Do not leave the work lamp unattended when it is being charged.

The rechargeable battery takes around 6 hours to charge. Switch off the work lamp while it is charging.

AFTER SALES SUPPORT

GB 0800 / 328 6020

00800 / 4467 5888

[e-mail]

• Remove the rubber lip 4 from the socket 5.
• Connect power supply connector or car cigarette lighter adapter to socket 5.
• Connect the power supply unit to a properly installed socket or the car cigarette lighter adapt to a live (turn ignition key to Pos. I if necessary) cigarette lighter adapter in a car.

Cordless LED Workshop Lamp Use

- The LED 7 illuminates red during the charging process. As soon as the charging process has ended, the LED illuminates green.

The rechargeable battery is protected from overloading by the electronics. Disconnect the work lamp from the power supply as soon as the LED 7 illuminates green. It is possible to recharge the battery at any time.

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

An empty battery charges in approx. 6 hours.

Information regarding the car cigarette lighter adapter

If charging with the car cigarette lighter adapter does not function, but the work lamp can be charged using the power supply unit, it is possible that the installed fuse has blown. Replace this as described below.

Fire hazard! Never bridge a defective fuse and only replace it with a fuse of the same type. Check the cable of the car cigarette lighter adapter for damage; replace the car cigarette lighter adapter, if necessary.

• Unscrew the ring on the adapter anti-clockwise.
• Replace the defective fuse with a new one of the type F0.5AL250V (0.5 A, 250 V, fl ink).

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

Cordless LED Workshop Lamp

Use

- Turn the coloured ring with the inserted metal cap clockwise to tighten.

Switching on and off

• Press the on/off-switch 6 to switch on the work light.
• Press the on/off-switch 6 again to switch off the work light.

In order to avoid glare from the work lamp, turn the work lamp to the side with the on/off switch 6 when you pull it apart.

The LEDs can be switched on during the charging process.

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

- The workshop lamp can be positioned using the magnet 9 on a magnetic surface or hung up by the hook.

10 /fold-out hook

In order to avoid damage to surfaces, do not slide the work lamp over the surface to which it is adhered. If necessary, place a rag, a piece of film or paper on the surface.

Cleaning

CAUTION! Prior to any cleaning, ensure that you disconnect the power supply unit from the socket/the car cigarette lighter adapter from the socket of the motor vehicle.

Never immerse the device in water or

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

Cordless LED Workshop Lamp Cleaning

Do not use any corrosive, aggressive or abrasive detergents in order to avoid damaging the surfaces.

Only use a well wrung-out, slightly dampened cloth with some dishwashing detergent for cleaning the work lamp, the power supply unit and the car cigarette lighter adapter.

Technical data

Cordless LED Workshop Lamp

Model: GT-LS12-UK

Battery: 3,7 V ===, 1800 mAh, Lithium-Ion rechargeable battery

Input: 12 V ---, Max 500 mA

LED Output: Max 2,5 W

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

Cordless LED Workshop Lamp Technical data

Power supply unit

Model: LY06-120-0500B

Input: 100-240 V\~, 50/60 Hz

Output: 12 V, 500 mA---

Cordless LED Workshop Lamp

Technical data

Car cigarette lighter adapter

Type: ZZ-103

Input / Output: 12 V / 12 V === ===

Fuse: F0.5AL250V

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

Cordless LED Workshop Lamp Technical data

The Cordless LED Workshop Lamp complies with the requirements of the EU directive 2004/108/EC (Electromagnetic compatibility) and complies with the critical values of the sections 6.5, 6.6, 6.8, 6.9 and attachment I of the EU Directive 72/245/EWG with the effective amendments of the 2006/96/EG (automotive directive).

Cordless LED Workshop Lamp Remove rechargeable battery prior to disposal

Remove rechargeable battery prior to disposal

Prior to removing the rechargeable battery, disconnect the work lamp from the power supply and completely discharge the battery! After removing the battery, the work lamp is destroyed and cannot be repaired.

Ensure that you wear safety glasses and safety gloves in order to avoid injuries to the eyes from splinters or cut injuries on the hands.

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

It is important that you follow steps 1

CAUTION FIRE HAZARD! To avoid a short-circuit and thus avoid a fire, the removal of the rechargeable batteries may only take place by a competent person when disposing of the product as described.

The battery cables must be cut separately. If the cables are cut at the same time the battery could short circuit.

Cordless LED Workshop Lamp

Remove rechargeable battery prior to disposal

Step 1 Step 2

Close-up of a flashlight with screw base and internal components (no visible text or symbols)

AFTER SALES SUPPORT

GB 0800 / 328 6020 IRE 00800 / 4467 5888

[e-mail]

WARRANTY CARD Cordless LED Workshop Lamp

Your details:

Name

Address

E mail

(for status reports for repair)

Date of purchase*

* We recommend you keep the receipt with this warranty card.

Location of purchase

Description of malfunction:

If after contacting the manufacturer you are requested to return the faulty product please return the completed warranty card together with it.

Globaltronics Service Center, c/o Bridges Logistics PO Box 1125, Bromley

BR1 9TW

[Non-Text]

AFTER SALES SUPPORT

0800/3286020

00800 / 4467 5888 [e-mail]

m = 311

MODEL: GT-LS12-UK PRODUCT CO

YEAR WARRANTY

PO51000314

The ALDI warranty offers you extensive benefits:

Warranty period: 3 years from date of purchase.

Costs: F r e

N O

F r e

ADVICE: Please contact our service hotline by

phone, e-mail or fax before sending in the device. This allows us to provide support in the event of possible

support in the event of possible operator errors.

In order to make a claim under the warranty, please send us:

- the faulty item together with the original

purchase receipt and the completed warranty card.

- the product with all components included in the packaging.

The warranty does not cover damage caused by:

- Accident or unanticipated events (e. g.

lightning, water, fire).

- Improper use or transport.

instructions.

- Other improper treatment or modification.

After the expiry of the warranty period, you still have the possibility to have your product repaired at your own expense. If the repair or the estimate of costs is not free of charge you will be informed accordingly in advance.

This does not affect your statutory rights.

In the event that a product is received for repair,

neither the service company nor the seller will assume any liability for data or settings possibly

stored on the product by the customer.

This sentence may be asked by SUA to be

sold.