HG02407 - Outdoor Lighting Livarno Lux - Free user manual and instructions

Product Type	Solar-Powered LED Wall Light
Model Number	HG02407
Brand	Livarno Lux
Dimensions (W x H x D)	15.5 x 10.2 x 7.3 cm
Weight	0.35 kg
Power Source	Integrated solar panel and rechargeable battery
Battery Type	Li-ion 3.7V 1200mAh
Light Source	LED, 0.5W, 30 lumens
Color Temperature	Warm white (3000K)
Auto On/Off	Dusk-to-dawn sensor
Waterproof Rating	IP44
Housing Material	ABS plastic and stainless steel
Mounting Type	Wall mounting with included screws
Charging Time	6-8 hours of direct sunlight
Operating Time	Up to 8 hours on full charge
Motion Sensor	Not applicable
Maintenance	Wipe with a damp cloth; do not use abrasive cleaners
Safety Features	Low-voltage operation, overcharge protection
Spare Parts Available	Replacement battery and LED module
Repair Policy	Professional repair recommended; user-replaceable battery
Warranty	2 years

Frequently Asked Questions - HG02407 Livarno Lux

How do I install the Livarno Lux solar wall light?

Mount the light on a wall using the included screws and anchors. Ensure the solar panel faces direct sunlight. The recommended mounting height is 2-3 meters.

What is the charging time and how long does it last?

Full charging takes 6-8 hours in direct sunlight. On a full charge, the light can operate for up to 8 hours. Actual duration depends on sunlight exposure.

Is the light waterproof?

Yes, it has an IP44 rating, meaning it is splash-proof and suitable for outdoor use. Do not submerge it in water.

How do I replace the battery?

Open the battery compartment on the back of the light. Replace with a compatible Li-ion 18650 battery (3.7V). Ensure polarity is correct. Close the compartment securely.

Does the light have a motion sensor?

No, this model operates with a dusk-to-dawn sensor that automatically turns the light on at night and off during the day. It does not have a motion sensor.

Can I use the light indoors?

It is designed for outdoor use due to its solar panel and waterproof rating. However, you can place it near a window indoors, but charging efficiency will be reduced.

What should I do if the light does not turn on at night?

Check that the solar panel is clean and not shaded. Ensure the battery is fully charged. If the issue persists, the battery may need replacement or the sensor may be faulty.

How do I clean the solar panel?

Wipe the solar panel gently with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials that could scratch the panel.

Is the light dimmable?

No, this model is not dimmable. It operates at full brightness when on.

Where can I find spare parts or accessories?

Spare parts such as replacement batteries and LED modules are available from Livarno Lux or authorized retailers. Contact customer service for assistance.

USER MANUAL HG02407 Livarno Lux

FOCO LED 18 W / FARO LED 18 W

ES

FOCO LED 18 W

Assembly, operating and safety instructions

IAN 286954

ES IT

GB / MT Assembly, operating and safety instructions Page 28

Intended use Page 29

Parts description Page 29

Technical data......Page 30

Scope of delivery Page 30

General safety instructions....Page 30

Before installation Page 31

Installation Page 32

Start-up Page 32

Adjusting the motion detector....Page 32

Setting the lighting duration....Page 33

Setting the daylight level Page 33

Aligning the motion detector....Page 33

Cleaning and Care Page 33

Disposal Page 33

Warranty Page 34

List of pictograms used
	Alternating current		Detection angle of motion detector: approx. 180°
	Splash-proof (IP44)		Motion detector detection range: approx.10 m
	LED lifespan Protection class I
	Power consumption per LED

LED spotlight 18 W

- Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

Intendeduse

The product is intended to illuminate indoor and outdoor areas. This product is only intended for

private use and is not suitable for commercial use or for use in other applications.

Partsdescription

1 Screw
2 Mounting bracket
3 Wall plug
4 Tooth lock washer
5 Flat washer
6 Spring washer
7 Locking screw (mounting bracket)
8 Spotlight
9 Locking screw (motion detector)
10 Motion detector
11 Insulation strip
12 Terminal block
13 Connection box
14 Cord anchorage
15 Translucent seal ring
16 Cable gland
17 Fixing screw (connection box)

18 Seal ring
19 TIME rotary control
20 LUX rotary control

●Technicaldata

Operating voltage: 230V\~50Hz

Total power consumption: 18 W

Illuminant: 30 x 0.5 W LED

(non-replaceable)

Twilight-switch:adjustablebetween

10|x - 20,000|x

Lighting duration: adjustable between

approx. 10s +/- 5s -

4min +/- 1min

Coverage angle of

motion detector: approx.180°

horizontal

Reach of the

motion detector: maximum 10 m

Protection class: I

Degree of protection: IP44 (splash-proof)

Overall dimension: 15.5 × 17.5 × 14.5 cm

Weight: approx. 460g

(includes accessories)

Projected area: max. 15.5 x 17.5 cm

Mounting height: approx. 1.8-2.5 m

TÜV SÜD / GS certified.

- Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 LED spotlight with motion detector
2 Wall plugs (∅ 8 mm)
2 Screws (∅ 5 mm × 50 mm)
1 Mounting bracket
1 Cord anchorage
2 Tooth lock washers
2 Flat washers
2 Spring washers
2 Locking screws
1 Instructions for use

Generalsafety instructions

BEFORE USING THE PRODUCT, PLEASE FAMILIARISE YOURSELF WITH ALL OF THE SAFETY INFORMATION AND INSTRUCTIONS FOR USE! WHEN PASSING THIS PRODUCT ON TO OTHERS, PLEASE ALSO INCLUDE ALL THE DOCUMENTS!

DANGER TO LIFE AND ACCIDENT HAZARD FOR TODDLERS AND SMALL

CHILDREN! Never leave children unattended

with the packaging material. The packaging material represents a danger of suffocation.

Children frequently underestimate the

dangers. Please keep the product out of the reach of children at all times.

This product may be used by children age 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or lacking experience and/or knowledge, so long as they are supervised or instructed in the safe use of the product and understand the associated risks. Children should not be allowed to play with the product. Cleaning and user maintenance should not be performed by children without supervision.
■ DANGER OF SUFFOCATION! Children could swallow and choke on small included parts (e.g. screws). Keep children away from the work area during assembly.
The illuminants are not replaceable.
If the illuminants fail at the end of their lives, the entire product must be replaced.

Danger to life by electric shock

■ Always check the product for damage before connecting it to the mains. Never use the product if it shows any signs of damage.
Prior to installation, verify that the mains voltage on site corresponds with the operating voltage required for the product (230 V\~50 Hz). Otherwise do not install the product.

CAUTION! DANGER OF BURN INJU-

RIES! To prevent burns, verify the product is switched off and has cooled down for at least 15 min before touching it. The product can become very hot.

FIRE HAZARD! Fit the product so that it is at least 1.0 m away from the material to be illuminated.

Excessive heat can result in a fire.

The product is only suited for use with the built-in LED control gear.
The product continues to draw a small amount of power even if the product is off as long as product is connected to supply mains. To switch the device off completely, the mains switch should be switched off.

● Before installation

Note: Remove all packaging materials from the product.

Important: The electrical connection must be established by a qualified electrician or a person trained to perform electrical installations. This person must be familiar with the properties of the product and the connection regulations.

Before installation ensure that the circuit, to which the product will be connected, is not energised. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).
Use a voltage tester to verify the de-energised status.
The included mounting material (screw ^16 and wall plugs 3) is suitable for ordinary solid concrete or masonry construction. Check which mounting material is suitable for your chosen mounting surface. If necessary, seek expert advice.

- Installation

Make sure you will not be drilling into electrical, gas or water lines inside the wall. Use a power drill to drill the holes into the brick wall. Always observe all safety instructions for the power drill in the manual for the power drill. Death or injury due to electric shock may otherwise result.

When selecting the mounting location, pay attention to the following:

Make sure that the spotlight illuminates the desired area. You can move the spotlight 8 vertically.
Make sure the motion detector covers the desired area. The motion detector has a maximum coverage range of max. 10 m, with a coverage angle of about 180^ (depending on the mounting height – a height of 1.80–2.50 m is ideal) (Fig. D, E, F).

Make sure the motion detected is not illuminated at night by street lighting. This can influence its functioning.

Use the mounting bracket ^2 as a pattern to mark the drilling holes onto the wall. Ensure that there are no cables or wires in this area in the wall. Drill two holes ( 8 mm) and insert the wall plugs ^3 . Screw the mounting bracket ^2 with the help of the screws ^1 and check the tight fit.

Open the connection box by using a crosshead screw driver to loosen the fixing screws 17 of the connection box 13 (Fig. B).

☐ The cable gland has to be loosened, then run the flexible supply line, e. g. type H05RN-F 3G 1.0 mm ^2 , through the cable gland 16 and into the connection box 13. Open the

terminal block 12 by using a slot head screw driver to loosen the screws.

☐ Attach ferrules to the wires of the supply line. Also attach the cord anchorage 14 to the supply line and use pliers to tighten it on the supply line (Fig. B). Connect them with the terminal block 12 in the connection box 13. Pay attention to the markings on the terminal block 12 (L for live, N for neutral and for the earth wire) (Fig. B). Close the terminal block 12 again by fastening the screws.

☐ Close the connection box again by fastening the fixing screws 17.

Now attach the spotlight to the mounting bracket 2 using the included locking screws 7, spring washers 6, flat washers 5 and tooth lock washers 4 (Fig. A).

☐ Re-install the fuse for this circuit or switch on at the circuit breaker (I position) in the fuse box.

- Start-up

- Adjusting the motion detector

Depending on the pre-adjustments of the motion detector 10, the product will switch itself on for a certain period of time as soon as the motion detector 10 detects movement. These pre-adjustments are made using the two controllers on the underside of the motion detector 10 (Fig. C).

- Setting the lighting duration

Turn the TIME rotary control on the bottom side of the motion detector 10 clockwise to increase the duration of illumination. The lighting duration can be adjusted within a time window of approx. 10s +/- 5s - 4min +/- 1min.

- Setting the daylight level

Turn the LUX rotary control on the bottom side of the motion detector 10 clockwise to increase the daylight level: In the position, the motion detector only reacts at night (at approx. 20 lx). In the * position, the motion detector also responds at daylight levels, as long as about 20,000 lx are not exceeded.

- Aligning the motion detector

Note: Perform this adjustment at twilight.

☐ Loosen the locking screw (motion detector) ☐ Turn the LUX rotary control to position * ☐ Align the motion detector into the central region of the desired coverage area.

Move about through the coverage area until you are satisfied with the response characteristics of the motion detector 10. To find the proper orientation, change the orientation of the motion detector 10.

☐ When you have aligned the motion detector 10 satisfactorily, re-tighten the locking screw 9 to fix the adjustment.

- Cleaning and Care

Before cleaning, remove the fuse or switch off the circuit breaker at the fuse box.
Never immerse the product in water or other liquids. Otherwise the product can be damaged.
☐ Clean the product with a lint-free, slightly moist cloth and mild cleaning agent.
☐ Re-install the fuse for this circuit or switch on at the circuit breaker (I position) in the fuse box.

- Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities. The Green Dot is not valid for Germany.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1-7: plastics / 20-22: paper and fibre-board / 80-98: composite materials.

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

proof of purchase. This warranty becomes void if the product has been damaged, or used or maintained improperly.

The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.

CE IP44

- Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.

The warranty for this product is 3 years from the date of purchase. Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you.

The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your