IAN 270802 - Lighting Livarno Lux - Free user manual and instructions

Product Type	Halogen Ceiling Light
Brand	Livarno Lux
Model	IAN 270802
Operating Voltage	230-240 V~, 50 Hz
Lamp Type	4 x Halogen GU10, 35 W
Maximum Power	140 W (4 x 35 W)
Protection Class	I
Protection Rating	IP20
Materials	Metal, glass, plastic
Intended Use	Indoor, dry spaces
Mounting	Ceiling, on normally inflammable surfaces
Safety Distance	At least 0.5 m from illuminated material
Lamp Replacement	Disconnect power, allow to cool, replace with same type
Cleaning	Use dry, lint-free cloth; do not use water or solvents
Included Accessories	4 lamps, glass plate, decorative rings, mounting hardware
Warranty	3 years (guarantee)
Compliance	CE, RoHS
Manufacturer	59929 Brilon, Germany
Disposal	Separate collection for electronic waste

Frequently Asked Questions - IAN 270802 Livarno Lux

Can I install this ceiling light myself?

The installation must be performed by a qualified electrician or a person trained in electrical installations due to risk of electric shock. Follow all safety instructions in the manual.

What type of bulbs does the light use?

The light uses 4 x halogen bulbs with GU10 base, 35 W each. Only use halogen bulbs with cover glass or low-pressure technology. Do not use cold light lamps with reflectors.

Can I use LED bulbs instead of halogen?

No, the light is specifically designed for halogen bulbs. Using LED bulbs may cause overheating or improper function. Always use the specified halogen bulbs.

How should I clean the ceiling light?

First, disconnect the light from the power supply by removing the fuse or switching off the circuit breaker. Allow the light to cool completely. Then clean with a dry, lint-free cloth. Do not use water, solvents, or abrasive cleaners.

What does the protection rating IP20 mean?

IP20 means the light is protected against solid objects larger than 12.5 mm (e.g., fingers) but not against water. It is suitable for indoor use in dry areas, not for bathrooms or outdoor locations.

Does the light come with bulbs?

Yes, the scope of delivery includes 4 halogen bulbs (GU10, 35 W) pre-installed. You also get a glass plate, decorative rings, and mounting hardware.

Can this light be dimmed?

The manual does not specify dimmability. It is likely not dimmable. If you require dimming, consult a qualified electrician and use compatible dimmable bulbs, but this may void the warranty.

What is the warranty period?

The product comes with a 3-year guarantee from the date of purchase, covering material and manufacturing defects. Keep your receipt as proof of purchase.

How do I replace a faulty bulb?

First, disconnect the power by removing the fuse or switching off the circuit breaker. Allow the bulb to cool. Remove the defective bulb by turning it 1/4 turn to the left. Insert a new GU10 halogen bulb (35 W) by turning it 1/4 turn to the right. Then restore power.

Is the light suitable for bathrooms or wet areas?

No, the light has an IP20 rating, which offers no water protection. It should only be installed indoors in dry, enclosed spaces. Do not expose to moisture or liquids.

USER MANUAL IAN 270802 Livarno Lux

HALOGEN CEILING LIGHT

GB

HALOGEN CEILING LIGHT

Assembly, operating and safety instructions

RO

PLAfONIERă Cu HALOGEN

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

RO

GB Assembly, operating and safety instructions Page 5

Intended use....Page 6

Scope of delivery Page 6

Parts description Page 6

Technical Data Page 6

Safety

Safety notices Page 7

Preparation

Required tools and material....Page 8

Prior to installation Page 8

Start-up

Mounting the light....Page 8

Replacing lamps....Page 9

Maintenance and Cleaning......Page 9

Disposal Page 9

Warranty and Service

Warranty Declaration......Page 9

Service address....Page 9

Declaration of conformity....Page 10

Manufacturer......Page 10

Halogen ceiling light

- Introduction

Congratulations on your new product. You have selected a high quality product. Please be sure to carefully read the complete operating instructions. Fold out the page with the illustrations. These instructions are part of the product and contain important information on setup and handling. Always follow all safety instructions. Before using this product for the first time verify the correct voltage and that all parts are properly installed. Should you have any questions or you are unsure about operating the product, please contact the dealer or service centre. Please keep these instructions in a safe place and pass them on third parties as applicable.

Intended use

This light is only suitable for indoor use in dry and enclosed spaces. The light can be fastened to any normally inflammable surface. This product is intended for private household use only.

Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 Halogen ceiling light 4-flame
4 Halogen lamps GU10, 35 W
1 Glass plate
4 Chrome-plastic decorative rings
2 Spacers
2 Large screws
6 Tooth lock washers
2 Washers (metal)
1 Metal plate
2 Washers (rubber, small)
2 Washers (rubber, large)
2 Box nuts

2 Screws (mounting angle)
2 Protective tubes
2 Screws
2 Wall plugs

1 Nut

1 Set of assembly instructions and instructions for use

Parts description

1 Mounting bracket
2 Wall plug
3 Retaining screws (connection housing)
4 Screws (mounting bracket)
5 Terminal block
6 Mains connection cable (external)
7 Protective tube
8 Connection housing
9 Glass plate
10 Box nut
11 Light bulb
12 Chrome-plastic decorative ring
13 Small washer (rubber)
14 Large washer (rubber)
15 Spacer
16 Nut
17 Tooth lock washer
18 Washer (metal)
19 Metal plate
20 Large screw

Technical Data

Item no.: 14106802L

Operating voltage: 230-240V\~, 50Hz

Lamp: halogen lamp GU10, 35 W

Rated power

maximum: 4 x 35 W

Protection class: I/

Protection type: IP20

Safety

Safety notices

Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions!

Avoid the risk of fatal injury from electric shock

■ Ensure that a qualified electrician, or a person trained to carry out electrical installations, performs the electrical installation.

Always check the light, power supply, and mains cable for damage before plugging it in. Never use the light if it shows any signs of damage.

CAUTION! A damaged mains cable indicates a life-threatening danger due to electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician.

Prior to installation, remove the fuse or switch off the circuit breaker (0 setting) in the fuse box.

Prior to installation verify the mains voltage on site corresponds with the operating voltage required for the light (230-240 V\~).

■ Ensure that the light does not come into contact with water or other liquids under any circumstances.

Never open any of the components of the electrical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock.

Do not install the light on a wet or conductive substrate!

Prevent fire and injury hazards

RISK OF INJURY! Check each lamp and lamp glass for damage immediately after unpacking.

Do not mount the light with defective lamps and/or lamp lenses. In this case contact the service centre for a replacement.

RISK OF BURNS! Ensure that the luminaire has been switched off and has cooled before touching it, to avoid burn injuries. Lamps develop a lot of heat in the area of the lamp head.

Allow the lamp to cool off completely.

- Replace defective bulbs with new ones immediately. Before changing bulbs, always first remove the fuse or switch off the circuit breaker.

FIRE HAZARD! Fit the light so that it is at least 0.5 m away from the material to be illuminated. Excessive heat can result in a fire.

Do not leave the light or packaging material lying unattended. Plastic film or bags, plastic parts, etc. can be dangerous for children to play with.

Do not use cold light lamps with reflectors.

Only use halogen light bulbs with cover glass or low-pressure technology.

Safe working

Only use 230-240 V \~ halogen lamps GU10 with a maximum output of 35W.

Mount the light so that it is protected from moisture and dirt.

Carefully prepare for assembly and allow yourself adequate time. Organise all parts and any necessary additional tools or materials before starting so they are easy to reach.

Always be attentive! Always pay attention to what you are doing and use common sense.

Never install the light if you are having difficulty concentrating or do not feel well.

● Preparation

- Required tools and material

The tools and materials specified are not included. This information and these values are non-binding and are only provided as a reference. The nature of the material is determined by the individual local conditions.

• Pencil/making tool
• Voltage tester
• Screwdriver
• Electric drill
• Bit (ø approx. 0.6 cm)
• Side cutting pliers
• Ladder

- Prior to installation

Important: The electrical connection must be established by a qualified electrician or a person trained to perform electrical installations. This person must be familiar with the properties of the light and the connection regulations.

Familiarise yourself with all the instructions and diagrams in this manual, as well as with the light itself, before you install it.
Before installation ensure that the circuit, to which the light will be connected, is not energised. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).
☐ Use the voltage tester to verify the de-energised status.

- Start-up

- Mounting the light

☐ Secure the chrome-plastic trim 12 to the smooth side of the glass plate 9, by pressing it into the opening in the glass plate.
☐ Remove the screws 4 visible at the side of the connection housing 8 and remove the mounting bracket 1 at the back.
☐ Insert the large screws 20 with one tooth lock washer each 17 from below through the connection housing 8 and the metal plate 19.
☐ Now insert one tooth washer 17, one washer 18 and a second tooth lock washer 17 on each of the screws 4.
☐ Fix the screws with the nuts provided 16.
☐ Insert a distance support 15 and a washer 14 (rubber, large) into the designated brackets in the light.
Place the glass plate 9 onto the spacer 15 and secure with the second washer 13 (rubber, small) and the box nut 10.
☐ Use the slotted holes in the mounting bracket 1 for the drill holes.
Now drill the fixing holes (approx. 6 mm, depth approx. 40 mm). Be careful not to damage the supply line.
□ Feed the power cord (external) through the cable guides 7.
☐ Insert the dowels into the bores.
☐ Fasten the mounting bracket with the provided screws 4.
Now connect the connection cable of the light to the mains connection cable (external) 6 using the included terminal block 5.
Note: Be sure to correctly connect each of the individual wires of the mains connection cable (external) 6: live wire, black or brown = symbol L, neutral wire, blue = symbol N, earth wire, green-yellow = symbol ⊥.
Now use the screws to connect the light to the mounting bracket 1.
☐ Use a clean, lint-free cloth to insert the lamps.

☐ Carefully insert the GU 10 halogen light bulb 11 into the socket and tighten it with a 14 turn to the right.

Ensure that it is properly positioned.

☐ Replace the fuse or switch on the circuit breaker in the fuse box (Position I).

Your light is now ready to use.

- Replacing lamps

CAUTION! RISK OF ELECTRIC SHOCK!

First disconnect the light from the mains when replacing the lamp. To do so, remove the fuse or switch off the circuit breaker in the fuse box (position 0).

☐ Allow the lamp to cool off completely.
☐ Use a clean, lint-free cloth to replace a bulb.
☐ Remove the defective GU10 light bulb from the socket with a 14 turn to the left.
☐ Carefully insert the new GU 10 light bulb into the socket and secure with a 14 turn to the right. Ensure that it is properly positioned.
☐ Reinsert the fuse or switch on the circuit breaker in the fuse box (I position).

Your light is now ready to use.

● Maintenance and Cleaning

CAUTION! RISK OF ELECTRIC SHOCK!

Disconnect the light from the mains circuit before cleaning. To do so, remove the fuse or switch off the circuit breaker in the fuse box (0 position).

CAUTION! RISK OF ELECTRIC SHOCK!

For electrical safety, never clean the light with water or other liquids, or immerse it in water.

CAUTION! DANGER OF BURN INJU-

RIES! Allow the light to cool completely.

Do not use solvents, benzene or similar substances. They could damage the light.
☐ Only use a dry, lint-free cloth for cleaning.

- Disposal

The package and packaging materials consist entirely of environmentally friendly materials. They can be disposed of at your local recycling facility.

The symbol of the wheelie bin with the line through it indicates within the European Union, this product must be dis-

posed of through separate refuse collection. This applies to the product and to all components bearing this symbol. Do not dispose of products bearing this symbol in your normal household waste, but instead they must be taken for recycling to a collection site for electrical and electronic appliances.

Recycling helps to reduce the consumption of raw materials and protects the environment.

● Warranty and Service

●WarrantyDeclaration

This product has a 3 year guarantee from the date of purchase extended only to the original buyer, not transferable. Please keep your receipt as proof of purchase. The guarantee applies to material or manufacturing defects only. It does not cover wear items or damage caused by improper use. Any modifications will void the guarantee. This warranty does not limit your legal rights. Please phone the service centre for guarantee claims. This is the only way to return your product free of charge.

Serviceaddress

Warranty and Service

Please have your receipt and the article number (e.g. IAN 12345) ready as your proof of purchase when enquiring about your product.

- Declaration of conformity CE

This product fulfils the requirements of the applicable European and national directives (Electromagnetic Compatibility 2004/108/EC, Low Voltage Directive 2006/95/EC, Ecodesign Directive 2009/125/EC, RoHS Directive 2011/65/EU). Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Manufacturer

59929 Brilon (Germany)