TK 2030 T - Cooker ECG - Free user manual and instructions

Product Type	Convector heater (fan heater)
Brand	ECG
Model	TK 2030 T
Rated Voltage	220–240 V~ 50 Hz
Power Consumption	1800–2000 W
Power Levels	2 (1200 W and 2000 W)
Fan	Built-in (TURBO function with fan)
Thermostat	Continuously adjustable
Heating Technology	Convection heating with temperature control
Safety Features	Overheating protection (thermal cut-out), safety cut out switch
Installation Type	Free-standing (requires base attachment)
Dimensions (Approx.)	450 x 200 x 250 mm
Weight (Approx.)	2.0 kg
Package Contents	1 convector, 2 base parts, 4 screws
Cleaning	Wipe outer surface with damp cloth; do not use abrasive cleaners
Storage	Clean, dry place away from dust
Environmental Protection	Dispose of at designated recycling centers for electronic equipment
Compliance	EU directives on electromagnetic compatibility and electrical safety

Frequently Asked Questions - TK 2030 T ECG

What are the power levels of the TK 2030 T convector?

The convector has two power levels: 1200 W (setting I) and 2000 W (setting II). It also offers TURBO modes with fan at both power levels, indicated by ^* I and ^* II.

Can I use the convector in a bathroom?

No, the convector must not be used close to a bathtub, shower, or pool. It is not designed for wet environments and should be placed away from water sources to avoid electric shock.

How do I clean the convector?

Always unplug the convector and let it cool completely. Clean the outer surface with a damp cloth. Do not use abrasive cleaners or sharp objects, as they may damage the surface.

What should I do if the convector automatically shuts off?

This indicates overheating protection has activated. Unplug the convector and let it cool for about 15 minutes. Then plug it back in and check that ventilation openings are not covered and the thermostat is set correctly.

Can I cover the convector?

No, never cover the convector. Covering can cause overheating and fire risk. Keep all vents unobstructed and maintain at least 30 cm clearance from surrounding objects.

Is it safe to leave the convector unattended?

Do not leave the convector with the power cord inserted unsupervised. Always unplug when not in use, especially when moving it or before cleaning.

How do I install the base?

Turn the convector upside down. Align the holes in the convector with the holes in the base parts. Tighten the four screws carefully and ensure the convector is stable before use. Never operate without the base attached.

What is the TURBO function?

The TURBO function uses the built-in fan together with the heating elements to circulate warm air faster. It is available at both power levels (1200 W and 2000 W) and helps heat the room more quickly.

What voltage does the convector require?

The converter operates at 220–240 V~ 50 Hz. Ensure your outlet voltage matches this and the socket is correctly grounded according to local electrical codes.

How should I dispose of the convector at the end of its life?

Do not dispose of it with household waste. Recycle it at designated collection points for electrical and electronic equipment. This helps protect the environment and human health.

USER MANUAL TK 2030 T ECG

Black electric heater with grid-patterned front panel and 'ECG' branding (no visible text or symbols on device body)

TK 2030 T

TEPLOVZDUŠNÝ KONVEKTOR NÁVOD K OBSLUŽE

TEPLOVZDUŠNÝ KONVEKTOR NÁVOD NA OBSLUHU

GRZEJNIK KONWEKTOROWY INSTRUKCJA OBSŁUGI

HÖSUGÁRZÓ HASZNÁLATI ÚTMUTATÓ

A. Temperature control

B. ON/OFF and power level control

HR/BIH

Do not immerse in water! – Neponořovat do vody!

INSTALACE

Technical line drawing of a mechanical clamp or bracket with a screwdriver inserted (no text or symbols)

Technical line drawing of a mechanical tool with a screwdriver inserted, no text or symbols present

Mechanical assembly diagram showing a tool inserted into a component with a ruler, labeled 'PL' (no text or symbols on the diagram itself)

Technical line drawing of a mechanical device with a screwdriver inserted, no text or symbols present

Technical line drawing of a mechanical clamp or bracket assembly with a screwdriver (no text or symbols)

Read carefully and save for future use!

Warning: The safety measures and instructions, contained in this manual, do not include all conditions and situations possible. The user must understand that common sense, caution and care are factors that cannot be integrated into any product. Therefore, these factors shall be ensured by the user/s using and operating this appliance. We are not liable for any damages caused during shipping, by incorrect use, voltage fluctuation or the modification or adjustment of any part of the appliance.

To protect against a risk of fire or electric shock, basic precautions shall be taken while using electrical appliances, including the following:

1. Make sure the voltage in your outlet corresponds to the voltage provided on the appliance label and that the socket is correctly grounded. The outlet must be installed in accordance with applicable electrical codes according to EN.
2. Do not operate the heat convector without the base properly attached.
3. Do not operate the device if the cord is damaged. All repairs, including cord replacements, must be carried out at a professional service centre! Do not remove the protective covers from the appliance; there is a risk of electric shock!
4. Protect the device from a direct contact with water and other liquids in order to prevent injury from electrical shock.
5. Do not use the convector outside or in wet environment and do not touch the power cable or the device with wet hands. Risk of electric shock.
6. Be cautious when using the convector near children!
7. Make sure the convector is placed on a flat surface.
8. Do not use the convector close to flammable objects or underneath them, e.g. curtains. The temperature of the surfaces near the

convector may be higher while it is in operation than usual. Place the convector to ensure sufficient air circulation.

1. Do not place the convector on a high pile carpet.
2. Do not place the convector in front of or directly under an electric socket.
3. Do not cover the heat convector! In case of covering it there is a risk of overheating of fire.
4. The convector must not be connected to the electrical outlet via a timer or connected to a remote switching power circuit, as in the case of remote switching on the covered or incorrectly placed convector there is a risk of fire.
5. Do not use the convector close to a bathtub, shower or a pool and do not place it in locations where is a danger of it falling into a bathtub or another container with water!
6. If the device emits an abnormal smell or smoke, immediately unplug it and have it checked by a service centre.
7. Do not switch off the device by pulling on the power cord. Always turn off the main switch of the convector first!
8. Always unplug the convector when moving it to another location.
9. Do not leave a convector with inserted power cord unsupervised. Disconnect the cord from the electrical outlet prior to any maintenance. Do not unplug the device by pulling the power cord. Unplug the power cord from the outlet by grasping the plug.
10. Do not allow the power cord to touch hot surfaces or run the cord over sharp edges.
11. Do not use the convector in places where flammable materials are stored (paint, gasoline, solvent etc.) or where there is a risk of flammable fumes appearing.
12. Do not put your fingers or other objects into the openings of the heat convector.

13. Do not cover the output vents by e.g. a towel or dry any laundry on it.

14. Use the convector only according to the instructions provided in this manual. The manufacturer is not liable for damages caused by the improper use.

15. This appliance can be used by children aged 8 years and older and people with lower physical or mental abilities or lack of experience and knowledge, if they are supervised or have been instructed to use the product in a safe manner and understand the potential dangers. Children must not play with the appliance. User cleaning and maintenance must not be performed by unsupervised children. Children under 8 years old must keep away from the appliance and its power supply.

16. Children under 3 years of age may not be near the device unless constantly supervised.

17. Children aged 3 to 8 years can turn the appliance on and off only if it is properly placed and installed in its correct working position when they are under supervision or have been instructed on the use of the appliance in a safe way and understand the potential dangers. Children aged 3 to 8 years are not allowed to plug the appliance, set controls, clean it or perform user maintenance.

WARNING: Some parts of the appliance may be hot during operation and can cause burns. It is necessary to exercise caution in the presence of children or persons with physical or mental impairments.

WARNING: The heater must not be operated without installed supports.

Do not immerse in water!

INSTALLATION

Make sure that the package contains all the parts required to assemble the convector. Contact your vendor if this is not the case.

Package contents:

1. Heat convector 1 piece
2. Base: 2 pieces
3. Attachment screws: 4 pieces

Always disconnect the power supply before any manipulation with the device in order to prevent electric shock.

WARNING

Never operate the heater without an attached base.

Installation requirements

Place the convector on a flat surface with a sufficient amount of space around the appliance to ensure the proper function of exhaust vents.

There must be a distance of at least 30 cm between the device and the surrounding objects.

WARNING

To prevent the device from overheating, do not cover the heater.

The heater must not be placed directly under an outlet.

The surfaces marked this way become hot during use.

DO NOT COVER!

WARNING

Some parts of this product may become very hot and cause burns. It is necessary to exercise extra caution in the presence of children or persons with impairments.

Installing supports

Technical line drawing of a mechanical component with a screwdriver inserted (no text or symbols)

1. Turn the convector upside down.
2. Attach the base so that the holes in a convector line up with the holes in the base.
3. Tighten the screws carefully and check if the convector is stable.

USING THE APPLIANCE

Note: When first switched on or switched on after a long period of inactivity, the heaters may emit odor or smoke. This is normal and will fade away in a short while.

This convector uses convection heating technology with temperature control. It is also equipped with the function TURBO (use of heating together with a fan) Thermostat control (A) is used to regulate temperature.

Turn the power control to set the required level: You can use the function TURBO to heat the room faster.

With the power control (B) you can set:

2 power levels:

I = 1200 W

II = 2000 W

2 power levels using the fan (TURBO):

^* =1200W

^* II = 2000 W

Any handling of the device can be done only when it is turned off using the main switch and unplugged from the outlet.

Turning off the convector

First, set the thermostat control to position „MIN" and switch to position "0". Then always unplug the power cable from the outlet!

The device shall only be handled when turned off via the switches and disconnected from the network outlet.

Protection against overheating

The internal thermal fuse protects the heater from overheating and automatically shuts down. In this case the operating indicator light turns off.

If the device shuts itself, unplug the power cable from the outlet. If it cools (in about 15 minutes), the device is again ready for use. Plug the power cable back into the socket.

If the situation repeats itself, check first, if the thermostat control is properly set and if the ventilation openings of the device are not covered.

CLEANING AND MAINTENANCE

Always unplug the power cable from the outlet and wait until the device entirely cools. Clean the outer surface of the convector with a damp cloth. Do not use for cleaning sharp objects or abrasive cleaners, you could damage the surface of the convector.

You can store the convector only after you properly turn off the main switch, disconnect it from the electrical outlet and let it cool completely.

CONVECTOR STORAGE

If you do not plan to use the appliance for a longer period of time, it should be placed in a clean and dry location protected against dust.

TECHNICAL DATA

Max. input power 2000 W

2 power levels: 1200 W a 2000 W

Built-in fan

Continuous thermostat regulation

Safety cut out switch

Free-standing

Nominal voltage: 220–240 V\~ 50 Hz

Nominal input power: 1800-2000 W

USE AND DISPOSAL OF WASTE

Wrapping paper and corrugated paperboard – deliver to scrapyard. Packing foil, PE bags, plastic elements – throw into plastic recycling containers.

DISPOSAL OF PRODUCTS AT THE END OF LIFETIME

Disposal of electric and electronic equipment (valid in EU member countries and other European countries with an implemented recycling system)

The represented symbol on the product or package means the product shall not be treated as domestic waste. Hand over the product to the specified location for recycling electric and electronic equipment. Prevent negative impacts on human health and the environment by properly recycling your product.

Recycling contributes to preserving natural resources. For more information on the recycling of this product, refer to your local authority, domestic waste processing organization or store, where you purchased the product.

This product complies with EU directive requirements on electromagnetic compatibility and electrical safety.

08/05

The instruction manual is available at website www.ecg-electro.eu.

Changes in text and technical parameters reserved.

GB

SIGURNOSNE UPUTE

Technical line drawing of a mechanical clamp or bracket with a screwdriver inserted (no text or symbols)

UPUTE ZA UPORABU

2 razine snage 1200 W i 2000 W

Ugrađeni ventilator

Kontinuirano podesivi termostat

Toplinski osigurač

Samostojeći

Nazivni napon: 220–240 V\~ 50 Hz

Nazivna snaga: 1800-2000 W

UPORABA I ODLAGANJE OTPADA

Technical line drawing of a mechanical clamp or bracket with a screwdriver inserted (no text or symbols)

Technical line drawing of a mechanical clamp or bracket with a screwdriver inserted (no text or symbols)