S39918 - Monitor Satco - Free user manual and instructions

Product type	T8 LED retrofit kit
Brand	Satco
Model	S39918
Tube length	4 feet (approximately 122 cm)
Base type	G13 (standard T8)
Power supply	Line voltage (120V-277V)
Typical wattage	Approximately 18-20 W (equivalent to 40W fluorescent)
Color temperature	Not specified, typically 4000K or 5000K
Luminous flux	Approximately 2000-2500 lumens
Color Rendering Index (CRI)	Greater than 80
Rated lifetime	50,000 hours
Certifications	c-UL-us, FCC Part 15
Protection rating	Suitable for damp locations
Housing material	Aging-resistant glass
Installation type	Single or double end (retrofit)
Ballast compatibility	Type B: direct line voltage, no ballast
Dimmer	Not compatible with standard dimmers
Compatible emergency equipment	Satco S8000 (5W LED emergency driver)
Applications	Residential, offices, commercial, warehouses
Warranty	Not specified, typically 5 years

Frequently Asked Questions - S39918 Satco

What type of luminaire supports this retrofit kit?

This kit is designed for T8 fluorescent fixtures with G13 bases, using traditional lamp holders connected directly to the branch circuit (Type B).

Can I use this tube with an existing ballast?

No, this tube is Type B and must be connected directly to the mains, without a ballast. The ballast must be bypassed or removed.

How to install this tube in single-ended mode?

Refer to the diagrams provided in the manual. Generally, one side of the fixture is connected to the line (L) and the other to the neutral (N). The sockets must not be shunted.

Does this tube work with a dimmer?

No, this tube is not compatible with standard incandescent lamp dimmers. Use only the control provided or specified by the manufacturer.

What safety precautions should be taken?

Always disconnect power before installation. Do not modify existing wiring unless necessary. Ensure the fixture is suitable for the kit's wattage.

Can this tube be used outdoors?

It is suitable for damp locations, but not for direct exposure to rain. Use it in protected fixtures.

Can I replace an existing fluorescent tube with this LED tube?

Yes, it is a retrofit. You must remove the ballast and rewire the fixture according to the instructions. The LED tube is directly compatible with the mains.

What is the lifespan of this tube?

The rated lifespan is approximately 50,000 hours, much longer than a standard fluorescent tube.

Is the tube dimmable?

No, it is not dimmable with standard dimmers. Consult the manufacturer for specific compatible dimmers.

What to do if the tube does not light up after installation?

Check that the power supply is correctly connected and the wiring is according to the diagrams. Ensure the sockets are not shunted and the ballast is bypassed.

USER MANUAL S39918 Satco

Models: S39917, S39918, S39919, S39920

INSTALLATION AND SAFETY INSTRUCTIONS

IMPORTANT: Read before installing fixture. Retain for future reference.

WARNING:

• DANGER: Risk of shock-disconnect power before installation.
• WARNING: Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
• WARNING: Product must be installed in accordance with the national electrical code or your local electrical code. If you are not familiar with these codes and requirements, contact a qualified electrician.
• WARNING: Install this kit only in luminaries that have the construction features and dimensions shown in the photographs and/or drawing and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
• WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• WARNING: To avoid potential fire or shock hazard, do not use this retrofit kit in luminaries employing shunted bi-pin lampholders. NOTE: Shunted lamp holders are found only in fluorescent luminaries with instant-start ballasts. Instant-start ballasts can be identified by the words "Instant Start" or "I.S." marked on the ballast. This designation may be in the form of a statement pertaining to the ballast itself, or may be combined with the marking for the lamps with which the ballast is intended to be used, for example F40T 12/IS, for more information contact the LED luminaire retrofit kit manufacturer.

Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. Installers should not disconnect the existing wire from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors.

- WARNING: Luminaire wiring and electrical parts may be damages when installing retrofit kit hardware. Check for enclosed wiring and components.

- WARNING: Check the existing wiring for damage before installing upgrade kit. Do not install if existing wires are damaged.

This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.

Type B Lamp – intended for operation in luminaires with traditional fluorescent-type lamp holders wired directly to the branch circuit. This includes both factory-wired luminaries as well as those converted for this purpose under a retrofit program.

THIS RETROFIT KIT INCLUDES, LED TUBE, OPERATING INSTRUCTIONS, AND FIXTURE LABEL FOR THE DOUBLE OR SINGLE ENDED APPLICATION.

• “This luminaire has been modified and can no longer operate the originally intended lamp,” shall be marked on the retrofit luminaire where readily visible by the user during normal maintenance including lamping.
• Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control. Please consult with manufacture for detailed dimmer information.
• Suitable for damp locations.
• Suitable for use in enclosed luminaries.
• Suitable for use with the following emergency equipment; SATCO Products, Inc., model S8000, 5W Emergency LED Driver.
• This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Features, applications and installation instructions continued on pages 2-4.

The units covered by this report were intended to retrofit surface mount, Type IC or non-IC recessed mount Listed fluorescent luminaires that use maximum 4 tubular lamps, the minimum lamp compartment dimensions are tabulated below.

Item Number-Description Volts		Minimum Lamp Compartment Dimensions (Length x Width x Height)	Lamp Quantity	Lamp-to-Lamp Spacing
S39917-15T8/LED/48-830/BP/SE-DES39918-15T8/LED/48-835/BP/SE-DES39919-15T8/LED/48-840/BP/SE-DES39920-15T8/LED/48-850/BP/SE-DE	120-277V	48 1/2 x 13 1/2 x 1 7/8 inches (1230 x 340 x 45 mm)	4	1 3/16 inches (30mm)

FEATURES

• c-UL-us classified and recognized

• Full glass housing: No aging, yellowing, bending

Single Ended

AC INPUT (120-277V) L N (L1)

APPLICATIONS

Widely used in residential buildings, offices, shopping malls, supermarkets, hospitals, assembly lines, warehouses, etc. for energy saving illumination.

Double Ended

AC INPUT (120-277V) L N (L1)

Rapid Start

Instant Start

The below ballast wiring represents typical configuration. The actual ballast wiring varies according to ballast model. The socket should be non-shunted.

INSTALLATION: SINGLE ENDED

Single Ended Retrofit Luminaire / 1 Lamp

graph TD
    A["Instant Start"] --> B["Electronic Ballast"]
    B --> C["Fluorescent lamp"]
    D["Rapid Start"] --> E["Electronic Ballast"]
    E --> F["Fluorescent lamp"]
    G["LED lamp"] --> H["N(L1)"]
    H --> I["L"]
    I --> J["×"]
    J --> K["×"]
    K --> L["×"]
    L --> M["×"]
    M --> N["×"]
    N --> O["×"]
    O --> P["×"]
    P --> Q["×"]
    Q --> R["×"]
    R --> S["×"]
    S --> T["×"]
    T --> U["×"]
    U --> V["×"]
    V --> W["×"]
    W --> X["×"]
    X --> Y["×"]
    Y --> Z["×"]
    Z --> AA["×"]
    AA --> AB["×"]
    AB --> AC["×"]
    AC --> AD["×"]
    AD --> AE["×"]
    AE --> AF["×"]
    AF --> AG["×"]
    AG --> AH["×"]
    AH --> AI["×"]
    AI --> AJ["×"]
    AJ --> AK["×"]
    AK --> AL["×"]
    AL --> AM["×"]
    AM --> AN["×"]
    AN --> AO["×"]
    AO --> AP["×"]
    AP --> AQ["×"]
    AQ --> AR["×"]
    AR --> AS["×"]
    AS --> AT["×"]
    AT --> AU["×"]
    AU --> AV["×"]
    AV --> AW["×"]
    AW --> AX["×"]
    AX --> AY["×"]

Single Ended Retrofit Luminaire / 2 Lamps

graph TD
    A["Electronic Ballast"] --> B["Fluorescent lamp"]
    C["N(L1)"] --> A
    D["LED lamp"] --> E["Fluorescent lamp"]
    F["Rapid Start Instant Start"] --> G["Electronic Ballast"]
    G --> H["Fluorescent lamp"]
    I["N(L1)"] --> J["LED lamp"]
    K["LED lamp"] --> L["Fluorescent lamp"]
    M["LED lamp"] --> N["Fluorescent lamp"]

Single Ended Retrofit Luminaire / 3 Lamps

graph TD
    A["Instant Start"] --> B["Electronic Ballast"]
    B --> C["Fluorescent lamp"]
    B --> D["Fluorescent lamp"]
    B --> E["Fluorescent lamp"]
    F["Rapid Start"] --> G["Electronic Ballast"]
    G --> H["Fluorescent lamp"]
    G --> I["Fluorescent lamp"]
    G --> J["Fluorescent lamp"]
    K["L"] --> L["N(L1)"]
    M["L"] --> N["N(L1)"]
    O["L"] --> P["N(L1)"]
    Q["L"] --> R["N(L1)"]
    S["L"] --> T["N(L1)"]
    U["L"] --> V["N(L1)"]
    W["L"] --> X["N(L1)"]
    Y["L"] --> Z["N(L1)"]
    AA["↓"] --> AB["LED lamp"]
    AC["LED lamp"] --> AD["LED lamp"]

Single Ended Retrofit Luminaire / 4 Lamps

graph TD
    subgraph Instant Start
        L1["L"] --> N1["Electronic Ballast"]
        N1 --> Fluorescent1["Fluorescent lamp"]
        N1 --> Fluorescent2["Fluorescent lamp"]
        N1 --> Fluorescent3["Fluorescent lamp"]
        N1 --> Fluorescent4["Fluorescent lamp"]
        N1 --> N2["L"]
        N2 --> N3["Electronic Ballast"]
    end

    subgraph Rapid Start
        L2["L"] --> N2
        N2 --> Fluorescent5["Fluorescent lamp"]
        N2 --> Fluorescent6["Fluorescent lamp"]
        N2 --> Fluorescent7["Fluorescent lamp"]
        N2 --> Fluorescent8["Fluorescent lamp"]
        N2 --> N3
        N3 --> LED1["LED lamp"]
        N3 --> LED2["LED lamp"]
        N3 --> LED3["LED lamp"]
        N3 --> LED4["LED lamp"]
        N3 --> LED5["LED lamp"]
    end

    L1 --> N1
    N2 --> N2
    N3 --> N3
    N3 --> N4["L"]
    N4 --> N3

The below ballast wiring represents typical configuration. The actual ballast wiring varies according to ballast model. It is not needed to change socket (if in good condition) to operate double ended lamps, regardless the type of sockets. Make sure one side of fixture is connected to the Live (L) and the other side to Neutral (N).

INSTALLATION: DOUBLE ENDED

Double Ended Retrofit Luminaire / 1 Lamp

graph TD
    subgraph Rapid Start
        A["Electronic Ballast"] --> B["Fluorescent lamp"]
        C["N(L1)"] --> D["LED lamp"]
        E["L"] --> F["LED lamp"]
        G["N(L1)"] --> H["LED lamp"]
    end

    subgraph Instant Start
        I["Electronic Ballast"] --> J["Fluorescent lamp"]
        K["L"] --> L["LED lamp"]
        M["N(L1)"] --> N["LED lamp"]
        O["L"] --> P["LED lamp"]
        Q["N(L1)"] --> R["LED lamp"]
    end

    style Rapid Start fill:#f9f,stroke:#333
    style Instant Start fill:#bbf,stroke:#333

Double Ended Retrofit Luminaire / 2 Lamps

graph TD
    A["L"] --> B["Electronic Ballast"]
    C["N(L1)"] --> B
    B --> D["Fluorescent lamp"]
    D --> E["LED lamp"]
    F["L"] --> G["LED lamp"]
    H["N(L1)"] --> G
    G --> I["LED lamp"]
    style A fill:#f9f,stroke:#333
    style C fill:#f9f,stroke:#333
    style F fill:#f9f,stroke:#333
    style H fill:#f9f,stroke:#333

graph TD
    A["L"] --> B["Electronic Ballast"]
    C["N(L1)"] --> B
    B --> D["Fluorescent lamp"]
    B --> E["Fluorescent lamp"]
    D --> F["LED lamp"]
    E --> F
    F --> G["LED lamp"]
    H["L"] --> I["N(L1)"]
    I --> J["LED lamp"]
    J --> K["LED lamp"]
    style A fill:#f9f,stroke:#333
    style C fill:#f9f,stroke:#333
    style H fill:#f9f,stroke:#333
    style I fill:#f9f,stroke:#333

Double Ended Retrofit Luminaire / 3 Lamps

graph TD
    A["L"] --> B["Electronic Ballast"]
    C["N(L1)"] --> B
    B --> D["Fluorescent lamp"]
    B --> E["Fluorescent lamp"]
    B --> F["Fluorescent lamp"]
    D --> G["LED lamp"]
    E --> G
    F --> G
    G --> H["LED lamp"]
    H --> I["LED lamp"]
    I --> J["LED lamp"]
    J --> K["LED lamp"]
    K --> L["LED lamp"]
    L --> M["LED lamp"]
    M --> N["LED lamp"]
    N --> O["LED lamp"]
    O --> P["LED lamp"]
    P --> Q["LED lamp"]
    Q --> R["LED lamp"]
    R --> S["LED lamp"]
    S --> T["LED lamp"]
    T --> U["LED lamp"]
    U --> V["LED lamp"]
    V --> W["LED lamp"]
    W --> X["LED lamp"]
    X --> Y["LED lamp"]
    Y --> Z["LED lamp"]
    Z --> AA["LED lamp"]
    AA --> AB["LED lamp"]
    AB --> AC["LED lamp"]
    AC --> AD["LED lamp"]
    AD --> AE["LED lamp"]
    AE --> AF["LED lamp"]
    AF --> AG["LED lamp"]
    AG --> AH["LED lamp"]
    AH --> AI["LED lamp"]
    AI --> AJ["LED lamp"]
    AJ --> AK["LED lamp"]
    AK --> AL["LED lamp"]
    AL --> AM["LED lamp"]
    AM --> AN["LED lamp"]
    AN --> AO["LED lamp"]
    AO --> AP["LED lamp"]
    AP --> AQ["LED lamp"]
    AQ --> AR["LED lamp"]
    AR --> AS["LED lamp"]
    AS --> AT["LED lamp"]
    AT --> AU["LED lamp"]
    AU --> AV["LED lamp"]
    AV --> AW["LED lamp"]
    AW --> AX["LED lamp"]
    AX --> AY["LED lamp"]
    AY --> AZ["LED lamp"]
    AZ --> BA["LED lamp"]
    BA --> BB["LED lamp"]
    BB --> BC["LED lamp"]
    BC --> BD["LED lamp"]
    BD --> BE["LED lamp"]
    BE --> BF["LED lamp"]
    BF --> BG["LED lamp"]
    BG --> BH["LED lamp"]
    BH --> BI["LED lamp"]
    BI --> BJ["LED lamp"]
    BJ --> BK["LED lamp"]
    BK --> BL["LED lamp"]
    BL --> BM["LED lamp"]
    BM --> BN["LED lamp"]
    BN --> BO["LED lamp"]
    BO --> BP["LED lamp"]
    BP --> BQ["LED lamp"]
    BQ --> BR["LED lamp"]
    BR --> BS["LED lamp"]
    BS --> BT["LED lamp"]
    BT --> BU["LED lamp"]
    BU --> BV["LED lamp"]
    BV --> BW["LED lamp"]

graph TD
    A["L"] --> B["Electronic Ballast"]
    C["N(L1)"] --> B
    B --> D["Fluorescent lamp"]
    B --> E["Fluorescent lamp"]
    B --> F["Fluorescent lamp"]
    D --> G["LED lamp"]
    E --> H["LED lamp"]
    F --> I["LED lamp"]
    G --> J["Final Output"]
    H --> J
    I --> J

Double Ended Retrofit Luminaire / 4 Lamps

graph TD
    A["Electronic Ballast"] --> B["Fluorescent lamp"]
    A --> C["Fluorescent lamp"]
    A --> D["Fluorescent lamp"]
    A --> E["Fluorescent lamp"]
    B --> F["LED lamp"]
    C --> G["LED lamp"]
    D --> H["LED lamp"]
    E --> I["LED lamp"]
    J["Instant Start"] --> K["Output"]

graph TD
    A["Electronic Ballast"] --> B["Fluorescent lamp"]
    A --> C["Fluorescent lamp"]
    A --> D["Fluorescent lamp"]
    A --> E["Fluorescent lamp"]
    B --> F["LED lamp"]
    C --> G["LED lamp"]
    D --> H["LED lamp"]
    E --> I["LED lamp"]
    J["L (L1)"] --> A
    K["N (L1)"] --> L["LED lamp"]
    M["L (L1)"] --> N["LED lamp"]

Modèles: S39917, S39918, S39919, S39920