ZY-40X8-4 - DIY tool Vevor - Free user manual and instructions

Product Type	Galvanized Steel Metal Edging
Brand	Vevor
Model	ZY-40X8-4
Dimensions (per section)	40 x 8 inches (101.6 x 20.32 cm)
Color	Black
Material	Galvanized Steel
Number of sections included	4
Number of connectors included	6
Gloves included	Yes (1 pair)
Tools required	Spade, hammer, wooden block
Installation	Partially bury in the ground and secure with a hammer (use a wooden block to protect the edging)
Use	Garden edging, flower beds, pathways
Safety	Wear ANSI-approved safety gloves and goggles during installation
Maintenance	Clean with a damp cloth if necessary; no special maintenance required
Rust resistance	Yes, thanks to the galvanized coating
Bending	Can be bent to the desired angle using a workbench or table
Warranty and support	Technical support and electronic warranty certificate at www.vevor.com/support

Frequently Asked Questions - ZY-40X8-4 Vevor

How to install the Vevor ZY-40X8-4 metal edging?

To install the edging, start by marking the edge line and removing obstacles. If the soil is rocky, loosen it with a spade. Then, bend the edging to the desired angle using a workbench or table. Insert the connected sections into the ground and tap them with a hammer while placing a wooden block to avoid damaging the edging. Finally, insert a connector to secure the connection between the sections.

Can the edging be cut to the desired length?

No, it is not recommended to cut the edging with a tool as it could cause injury and damage the galvanized coating. The sections are designed to be used as is. If you need a different length, choose the appropriate model.

What tools do I need for installation?

The required tools are a spade, a hammer, and a wooden block. The spade is used to prepare the soil, the hammer to drive the edging in, and the wooden block to protect the edging during hammering.

Is the edging rust resistant?

Yes, the edging is made of galvanized steel, which provides excellent resistance to rust and corrosion, even outdoors.

How to connect multiple sections together?

Each section is connected using the provided connectors. After aligning the sections, insert a connector into the designated slots to secure the pieces together. The connection is secure and durable.

Can I bend the edging to follow a curve?

Yes, the edging can be bent manually to conform to the desired shape. Use a workbench or the edge of a table as support for a clean bend. You can create curves or right angles as needed.

What to do if a section is damaged?

If a section is damaged, it is recommended to replace it with a new section of the same model. The edging is not repairable. Contact customer service at www.vevor.com/support for replacement parts.

How to clean and maintain the edging?

Maintenance is simple: clean the edging with a damp cloth if dirty. Avoid abrasive products that could scratch the galvanized coating. No special maintenance is required.

What safety precautions should be taken?

During installation, wear ANSI-approved safety goggles and robust work gloves for protection. Ensure the work area is clean and well-lit, and do not work if you are tired or under the influence of substances.

Where to find replacement parts or support?

For technical assistance or to obtain replacement parts, visit www.vevor.com/support. There you will find the electronic warranty certificate and can contact customer service.

USER MANUAL ZY-40X8-4 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

GALVANIZED STEEL METAL EDGING

USER MANUAL

MODEL: ZY-40X6-3Black / ZY-40X6-4Black / ZY-40X6-6Black / ZY-40X8-3Black / ZY-40X8-4Black / ZY-40X8-6Black / ZY-40X12-4Black

We continue to be committed to providing you with tools at competitive prices.

"Save Half", "Half Price", or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to other brands, and do not necessarily mean to cover all categories of tools offered by us. We kindly remind you to verify carefully when placing an order with us if you are actually saving half compared to the top major brands.

Model: ZY-40X6-3Black / ZY-40X6-4Black / ZY-40X6-6Black / ZY-40X8-3Black / ZY-40X8-4Black / ZY-40X8-6Black / ZY-40X12-4Black

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact Technical Support and E-Warranty Certificate at www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.

WARNING:

Read this material before using this product. Failure to do so can result in serious injury.

Assembly precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or when under the influence of alcohol, or medication.
6. The product capabilities apply to properly and completely assembled products only.
7. Assemble on a flat, level, hard and smooth surface capable of supporting the Wooden Hall Tree.
8. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

SAVE THIS MANUAL

PRODUCT SPECIFICATIONS

Model	ZY-40X6-3Black
Size of Single metal edge	40*6in
Color	Black

Model	ZY-40X6-4Black
Size of Single metal edge	40*6in
Color	Black

Model	ZY-40X6-6Black
Size of Single metal edge	40*6in
Color	Black

Model	ZY-40X8-3Black
Size of Single metal edge	40*8in
Color	Black

Model	ZY-40X8-4Black
Size of Single metal edge	40*8in
Color	Black

Model	ZY-40X8-6Black
Size of Single metal edge	40*8in
Color	Black

Model	ZY-40X12-4Black
Size of Single metal edge	40*12in
Color	Black

PRODUCT COMPONENTS

Model
	Metal edge	Connector	Gloves
ZY-40X6-3Black	x3	x5	X1
ZY-40X6-4Black	x4	x6
ZY-40X6-6Black	x6	x8
ZY-40X8-3Black	x3	x5
ZY-40X8-4Black	x4	x6
ZY-40X8-6Black	x6	x8
ZY-40X12-4Black	x4	x6

ZY-40X6-3Black / ZY-40X6-4Black / ZY-40X6-6Black

ZY-40X8-3Black / ZY-40X8-4Black / ZY-40X8-6Black

ZY-40X12-4Black

REQUIRED TOOLS

Spade
Hammer and a block of wo

PRODUCT ASSEMBLY INSTRUCTIONS

STEP 1: Prepare a line for the edging to follow and remove any obstructions. If ground is stony, loosen with pickaxe.

STEP 2: Bending instructions: A work bench, the edge of a table, or other former is advised when bending the metal edge to the required shape.

NOTE: Do not cut with anything as it can cause injury.

STEP 3: Insert the connected metal edges into the ground and set with a hammer.

NOTE: Place a piece of wood over the metal edge when striking with a hammer to avoid damaging the metal edge.

Supplementary statement: The metal barrier can be bent into the shape you need according to your needs (Including but not limited to the following shapes).
①
②
③

CLEAR ENGRAVED GRADUATIONS

Precision control of rotation degree

Manufacturer: Shanghai Muxin Muye Youxiangongsi

Address: Shuangcheng Lu 803 Nong 11 Hao 1602A-1609 Shi, Baoshan Qu, Shanghai 200000 CN.

EC REP: E-CrossStu GmbH.

Mainzer Landstr. 69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road,

Staines-upon-Thames, Surrey, TW18 4AX

Imported to AUS: SIHAO PTY LTD.

1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd.

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

Precision control of rotation degree

Manufacturer: Shanghai Muxin Muye Youxian Gongsi

Address: Shuangchenglu 803 nong 11 hao 1602A-1609 shi, Baoshan Qu, Shanghai 200000 CN.

EC REP: E-CrossStu GmbH.

Mainzer Landstr. 69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED.

C/O YH Consulting Limited, Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

Imported into AUS: SIHAO PTY LTD.

1 ROKEVA STREET, EASTWOOD, NSW 2122, Australia

Imported into USA: Sanven Technology Ltd.

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

Precision control of rotation degree

Staines-upon-Thames, Surrey, TW18 4AX

Imported into AUS: SIHAO PTY LTD.

1 ROKEVA STREET, EASTWOOD, NSW 2122, Australia

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

Precision control of rotation degree

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Staines-upon-Thames, Surrey, TW184AX

Imported into AUS: SIHAOPTYLTD.

1ROKEVASTREETEASTWOODNSW2122Australia

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

INSTRUCTIONS FOR PRODUCT ASSEMBLY

Precision control of rotation degree

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

ECREP: E-CrossStuGmbH.

Mainzer Landstr. 69, 60329 Frankfurt am Main.

UKREP: YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

Imported to AUS: SIHAO PTY LTD.

1 ROKEVA STREET, EASTWOOD NSW 2122, Australia

Imported to USA: Sanven Technology Ltd.

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical support and e-warranty certificate www.vevor.com/support

GALVANIZED STEEL METAL EDGING

USER MANUAL

MODEL: ZY-40X6-3 Black / ZY-40X6-4 Black / ZY-40X6-6 Black / ZY-40X8-3 Black / ZY-40X8-4 Black / ZY-40X8-6 Black / ZY-40X12-4 Black

NEED HELP? CONTACT US!

Precision control of rotation degree

Manufacturer: Shanghai Imuxin Wood Industry Co., Ltd.

Address: Room 1602A-1609, No. 11, Lane 803, Shuangcheng Road, Baoshan District,

Shanghai 200000, China.

EC REP: E-CrossStu GmbH.

Mainzer Landstr. 69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED.

C/O YH Consulting Limited, Kantoor 147, Centurion House, London Road,

Staines-upon-Thames, Surrey, TW18 4AX

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

Warranty certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

PRODUCT FEATURES

PRODUCT ASSEMBLY INSTRUCTIONS

Precision control of rotation degree

Manufacturer: Shanghai Muxin Muye Youxian Gongsi

Address: Shuangchenglu 803 nong 11 hao 1602A-1609 shi, Baoshan Qu,

Shanghai 200000 CN.

EC REP: E-CrossStu GmbH.

Mainzer Landstr. 69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED.

C/O YH Consulting Limited Bureau 147, Centurion House, London Road, Staines-upon-

Thames, Surrey, TW18 4AX

1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

Precision control of rotation degree

Manufacturer: Shanghai Muxin Muye Co., Ltd.

Address: Room 1602A-1609, No. 11, Lane 803, Shuangcheng Road, Baoshan District, Shanghai 200000, CN.

EC REP: E-CrossStu GmbH.

Mainzer Landstr. 69, 60329 Frankfurt am Main.

UK REP: YH CONSULTING LIMITED.

C/O YH Consulting Limited, Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support