PR-012-65 - DIY tool Vevor - Free user manual and instructions

Product Type	Ninja Obstacle Course and Slackline Kit
Brand	Vevor
Model	PR-012-65
Ribbon Length	19.8 meters (65 feet)
Number of Included Pieces	12
Six-layer Rope Ladder	1 piece
Flexible Swing Panel	1 piece
Climbing Web	1 piece
Triangular Gymnastics Ring	1 piece
Buranko Corner Swing	1 piece
Monkey Knot	2 pieces
Monkey Fist	2 pieces
Gymnastics Ring	2 pieces
Spinning Wheel	1 piece
Primary Use	Creating Ninja Obstacle Courses and Slacklines
Cleaning	Soft dry cloth or clean water, dry after cleaning
Safety	Read the manual, keep out of reach of children, do not use under influence
Warranty	Technical support and electronic warranty certificate at www.vevor.com/support
Manufacturer	Shanghai Muxinmuyeyouxiangongsi, Baoshan, Shanghai, China
Country of Manufacture	China
Importer (Australia)	SIHAO PTY LTD, Eastwood NSW
Importer (United States)	Sanven Technology Ltd, Rancho Cucamonga, CA
Importer (EU)	YH CONSULTING LIMITED, Frankfurt am Main

Frequently Asked Questions - PR-012-65 Vevor

How to install the Vevor PR-012-65 kit?

Follow the installation instructions provided in the manual. For the Ninja obstacle course, use the straps and carabiners to attach the elements to trees or a stable structure. For the slackline, tighten the ribbon between two strong anchor points. Refer to the illustrated guide for more details.

What safety precautions should be taken?

Read all instructions carefully before use. Wear gloves during assembly. Do not climb if you are tired or under the influence of alcohol, drugs or medication. Keep small parts out of reach of children to avoid choking hazards. Inspect the device before each use.

How to clean and maintain the kit?

Wipe the parts with a soft dry cloth. Use clean water if necessary, then dry thoroughly. Never use abrasive cleaners or harsh pads. Keep the product dry after cleaning. Children should not participate in cleaning.

What accessories are included in the PR-012-65 model?

The kit contains 12 pieces: 1 six-layer rope ladder, 1 flexible swing panel, 1 climbing web, 1 triangular gymnastics ring, 1 buranko corner swing, 2 monkey knots, 2 monkey fists, 2 gymnastics rings, 1 spinning wheel and 1 19.8 meter ribbon.

Can I use this kit outdoors?

Yes, the kit is designed for outdoor use. Make sure to attach it to solid and stable structures (trees, poles). Avoid areas with potential hazards. Store the kit indoors or sheltered from the weather when not in use.

What is the length of the slackline ribbon?

The specified ribbon is 65 feet (19.8 meters). This length allows you to create a slackline suitable for most outdoor spaces.

Is it suitable for children?

The kit is designed for children and adults, but adult supervision is required. Respect the weight limits and recommendations in the manual. Small parts pose a choking hazard to young children during assembly.

How to store the kit after use?

After disassembly, clean and dry all parts. Store them in a dry place away from direct sunlight. Use the original bag if available to avoid loss of small accessories.

What to do if a part is damaged?

Do not use the kit with damaged parts. Contact Vevor technical support via www.vevor.com/support for replacement parts or repair advice. Keep your electronic warranty certificate.

Is there a warranty for this product?

Yes, Vevor offers an electronic warranty. Go to www.vevor.com/support to register your product and access technical support. The warranty covers manufacturing defects under normal use conditions.

USER MANUAL PR-012-65 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

NINJA LINE/SLACK LINE KIT

MODEL: PR-012-50/PR-010-50/PR-012-56/PR-014-60/PR-012-65/PR-03-60

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent savings you might benefit from buying certain tools with us compared to top brands, and do not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: PR-012-50/PR-010-50/PR-012-56/

PR-014-60/PR-012-65/PR-03-60

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

	Warning-To reduce the risk of injury, user must read instructions manual carefully.
	Be careful to pinch your hands.

SAFETY WARNINGS AND PRECAUTIONS

Thank you for using this product. In order to ensure that you can operate the machine correctly, read this instruction carefully before operation and keep it properly for future reference. Please be sure to follow the precautions and safety rules on this page to ensure your safe use. The manual will outline safety warnings and precautions, operating, maintenance, and cleaning. The warnings and instructions reviewed in the manual cannot cover all possible conditions and situations that may occur. Caution and common sense are not built into this product, since we expect that the users will comply with these codes.

Please read ALL the instructions before using your machine.

1. Assembly needs to follow these instructions. Incorrect assembly can create a hazard. Wear heavy-duty work gloves during assembly.
2. Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
3. Keep the assembly area clean and well-lit.
4. Inspect before every use. Do not use it if parts are loose or damaged.

WARNING:

- This product contains small parts. If swallowed, it will pose a choking hazard. Keep these small parts away from children when assembling!

TIPS: Before installation, the packaging can be laid flat on the ground, and the product placed on the packaging for assembly to protect the process. About this item.

Product related parameters

Model	PR-012-50	PR-010-50	PR-012-56	PR-014-60	PR-012-65	PR-03-60
Ribbon specifications	50FT	50FT	56FT	60FT	65FT	60FT
Six layer rope ladder	1	1	1	1	1
Soft board swing	1	1	1	1	1
Climbing the web	1	1	1	1	1
Climbing rope	/	/	/	1	/
Kuchu buranko	1	/	/	1	1
Gymnastic Triangle Ring	1	/	/	2	1
Monkey pole	2	3	3	2	2
Monkey fist	2	3	3	2	2
Gymnastic Circle	2	/	2	2	2
Rotating wheel	1	1	1	1	1
Total quantity	12	10	12	14	12	/

PR-012-50

Installation instructions

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They can not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation. You can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slacklinel kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing go through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet. Until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180 ° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

Installation instructions

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to slow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

PR-012-56

Installation instructions

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Installation instructions

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-65

Installation instructions

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m(7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you cannot pull the handle of the ratchet. Note: Please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to store the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-03-60

Installation instructions

• HOW TO SET UP A SLACKLINE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninjaline, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. They can not only protect trees, but also reduce the wear of the slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the installation height difference of two slacklines be slightly less than: your child's height + half of the length of the balance belt, and the slackline at the bottom is about 23.6in from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of the ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet. Until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180 degrees at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

CLEANING AND STORAGE

1. Wipe with a soft, dry cloth. Never use an abrasive cleanser or heat. Wipe with clean water. Keep product dry after cleaning.
2. Children are not allowed to wipe the product to avoid tipping and injuries.
3. After the product is disassembled, please put the parts and accessories together.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Cent House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EC

REP

E-CrossStu GmbH

Mainzer Landstr. 69, 60329 Frankfurt am Main

Made in China

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

When you are ready to stow the slackline kit, pull the switch marked in the figure outward and simultaneously open the handle of the ratchet to about 180°. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-56

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8 inches.

If you are unable to determine the exact location during installation, you can straighten the main line and lay it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then, with one hand, tighten the webbing while holding the ratchet handle with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can no longer pull the handle. Note: ensure the ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and simultaneously open the ratchet handle to about 180°. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Step 1: Where to Slackline?

Choosing a location for slacklining is mostly based on personal preference. To set up the ninja line, you will need two objects to anchor it (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slacklining), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, or loose soil. This is only a partial list. You must use your good judgment to determine what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-65

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the hole is not positioned at the top, you can adjust it by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then, tighten the webbing with one hand while holding the ratchet handle with the other. Tighten the webbing by continuously opening and closing the ratchet until you can no longer pull the handle. Note: Make sure the ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and open the ratchet handle to about 180° at the same time. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Step 1: Where to Slackline?

Choosing a place to slackline is mostly based on personal preference. To set up the ninja line, you will need two objects to tie it to (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, or loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the height difference between the two slacklines be slightly less than: your child's height + half the length of the balance belt, and the bottom slackline should be about 23.6 inches from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

A/S YH Consulting Limited Bureau 147, Centurion Maison, London Road, Staines-upon-Thames, Surrey, TW18 4AX

E-CrossStu GmbH

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then, tighten the webbing with one hand while holding the ratchet handle with the other. Continue opening and closing the ratchet to tighten the webbing until you can no longer pull the handle. Note: ensure the ratchet is closed when it is finally tightened.

3. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and open the ratchet handle to about 180° at the same time. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

Step 1: Where to Slackline?

Choosing a location for slacklining is mostly based on personal preference. To set up the ninja line, you will need two objects to anchor it (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline); live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, or loose soil. This is only a partial list. You must use your good judgment to determine what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-56

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They can not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-03-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninjaline, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the installation height difference of two slacklines be slightly less than: your child's height + half of the length of the balance belt, and the slackline at the bottom is about 23.6in from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing go through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet. Until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

C/O YH Consulting Limited Office 147, Centurion Haus, London Road, Staines-upon-Thames, Surrey, TW18 4AX

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

3 When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8 inches.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-56

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the hole is not positioned at the top, you can adjust it by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then, tighten the webbing with one hand while holding the ratchet handle with the other. Continue opening and closing the ratchet to tighten the webbing until you can no longer pull the handle. Note: Make sure the ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and open the ratchet handle to about 180° at the same time. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-65

Step 1: Where to Slackline?

Choosing a place to slackline is mostly based on personal preference. To set up the ninja line, you will need two objects to tie it to (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, or loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-03-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninjaline, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the installation height difference of two slacklines be slightly less than: your child's height + half of the length of the balance belt, and the slackline at the bottom is about 23.6 inches from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of the ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

Imported in AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD

New South Wales 2122 Australia

C/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

Electronics www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8 inches.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand while holding the ratchet handle with the other. Continue opening and closing the ratchet to tighten the webbing until you can no longer pull the handle. Note: ensure the ratchet is closed when fully tightened.

3. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and simultaneously open the ratchet handle to about 180°. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

Step 1: Where to Slackline?

Choosing a location for slacklining is mostly based on personal preference. To set up the ninja line, you will need two objects to anchor it (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline); live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, or loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-56

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce the wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-03-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninjaline, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. They can not only protect trees, but also reduce the wear of the slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the installation height difference of two slacklines be slightly less than: your child's height + half of the length of the balance belt, and the slackline at the bottom is about 23.6in from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing go through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet. Until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

CLEANING AND STORAGE

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

E-CrossStu GmbH

NEED HELP? CONTACT US!

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

3 When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline); live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Recommended installation height: more than 2.2 m (7.2 ft).

Of course, this value is not absolute. You can adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8–15.8 in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you cannot pull the handle of the ratchet. Note: Please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-56

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you cannot pull the handle of the ratchet. Note: Please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-03-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninjaline, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce wear on the slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the height difference between the two slacklines be slightly less than your child's height plus half the length of the balance belt, and the lower slackline should be about 23.6 inches from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slacklines.)

Step 5: How to use the slackline ratchet?

We have introduced the use of the ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the hole is not positioned at the top, you can adjust it to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand while holding the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

CLEANING AND STORAGE

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

Przedstawiciel UE

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main.

NEED HELP? CONTACT US!

www.vevor.com/support

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation. You can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet. Until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

3 When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180 ° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline); live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation. You can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use the carabiners to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-56

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Recommended installation height: more than 2.2 m (7.2 ft).

Of course, this value is not absolute. You can adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8–15.8 in.

If you are unable to determine the exact location during installation, you can straighten the main line and lay it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you cannot pull the handle of the ratchet. Note: Please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-014-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: Please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8-15.8 inches.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not on top, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand while holding the handle of the ratchet with the other. Tighten the webbing by continuously opening and closing the ratchet until you can no longer pull the handle. Note: make sure the ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-03-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninjaline, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. They not only protect trees but also reduce the wear of the slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the installation height difference of two slacklines be slightly less than: your child's height + half of the length of the balance belt, and the slackline at the bottom is about 23.6in from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

Mainzer Landstr. 69, 60329 Frankfurt am Main.

Made in China

VEVOR®

TOUGH TOOLS, HALF PRICE

Warranty certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

3 When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-010-50

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline); live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect trees, but also reduce the wear of the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the hole is not positioned at the top, you can adjust it by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand while holding the ratchet handle with the other. Tighten the webbing by continuously opening and closing the ratchet until you can no longer pull the handle. Note: make sure the ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, pull the switch marked in the figure outward and open the ratchet handle to about 180° at the same time. After hearing a "bang", you can pull the webbing out of the ratchet and put it away.

• HOW TO SET UP A NINJA OBSTACLE COURSE?

Step 1: Where to Slackline?

Choosing a place to slackline is mostly based on personal preference. To set up the ninja line, you will need two objects to tie it to (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, or loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees but also reduce wear on the slackline.

Installation height: more than 2.2m (7.2ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

▲ MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. They not only protect the trees, but also reduce wear on the slackline.

Installation height: more than 2.2 m (7.2 ft) is recommended.

Of course, this value is not absolute. You can adjust the installation height of the slackline appropriately according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles onto the main line.

It is recommended to install a hanging buckle every 11.8–15.8 in.

If you are unable to determine the exact location during installation, you can straighten the main line and place it on the ground. Then measure with a tape measure and mark the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: If you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you cannot adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang" you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty Certificate www.vevor.com/support

PR-012-65

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, please contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Installation height: more than 2.2m (7.2ft) is recommended

Of course, this value is not absolute. You can appropriately adjust the installation height of the slackline according to your child's height.

Step 3: Install the main line and ratchet line on the installed tree protectors.

Step 4: Install the hanging buckles to the main line.

It is recommended to install a hanging buckle every 11.8-15.8in.

If you are unable to determine the exact location during installation, you can straighten the main line and put it on the ground. Then measure with a tape measure and mark on the main line with a marker pen.

Step 5: Use the ratchet to tighten the main line of the slackline.

Tip: if you need to adjust the position of your hanging buckles, you must loosen the ratchet line before adjustment. Because the friction between the buckles and the main line is very large when the main line is tightened, you can't adjust the position of the hanging buckles.

Step 6: Use contact buckles to hang all accessories on the hanging buckle and tighten it.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your ninja slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE

1. First, close the ratchet and thread the webbing through the upper hole in the middle of the ratchet. If the position of the hole is not above, it can be adjusted to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

PR-03-60

Step 1: Where to Slackline?

Picking a place to slackline is mostly based on personal preference. To set up the ninja line, two objects will be needed to tie it into place (typically trees).

MATTERS NEEDING ATTENTION:

Do not use buildings or playground structures (unless specifically built for slackline), live power/telephone poles, dead trees or stumps, trees with rot, disease, structural cracks, excessive lean, exposed roots, or trees in boggy, wet, sandy, loose soil. This is only a partial list. You must use your good judgment in determining what is not an appropriate anchor point. If in doubt, contact us.

Step 2: Install tree protectors. It can not only protect trees, but also reduce the wear of slackline.

Step 3: Attach the main line to a tree or solid post.

Installation height: Generally, we recommend that the installation height difference of two slackline be slightly less than: your child's height + half of the length of the balance belt, and the slackline at the bottom is about 23.6in from the ground. Of course, you can adjust the height according to your actual situation.

Step 4: Attach the ratchet line to another tree or solid post. Put the ratchet protector on first. Then use the ratchet to tighten the main line of the slackline. Cover the protective sleeve onto the ratchet again. (The protective sleeve is used for 2-inch slackline.)

Step 5: How to use the slackline ratchet?

We introduced the use of ratchet on the right.

Please note that after installing the accessories, you need to test their reliability. We sincerely hope you enjoy your slackline kit as much as possible. Have fun!

• HOW TO USE THE RATCHET LINE?

1. First, close the ratchet, and thread the webbing through the upper hole in the middle of the ratchet. If the hole is not positioned at the top, you can adjust it to the top by opening and closing the ratchet.
2. Pull the webbing down until it is as tight as possible. Then tighten the webbing with one hand and hold the handle of the ratchet with the other hand. Tighten the webbing by continuously opening and closing the ratchet until you can't pull the handle of the ratchet. Note: please make sure your ratchet is closed when it is finally tightened.

1. When you are ready to stow the slackline kit, you can pull the switch marked in the figure outward and open the handle of the ratchet to about 180° at the same time. After hearing the "bang", you can pull the webbing out of the ratchet and put it away.

Technical Support and E-Warranty

Certificate www.vevor.com/support

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main.

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support