HSTW-12 - Towel rack Vevor - Free user manual and instructions

Product Type	Towel Warmer Bucket
Brand	Vevor
Model	HSTW-12
Dimensions (L x D x H)	320 x 320 x 470 mm
Net Weight	4.2 kg
Capacity	20 liters (approx. 2 large towels or one blanket)
Power Supply	120 V~ 60 Hz (North America) or 230 V~ 50/60 Hz (Europe/Australia)
Power	450 W (+5%/-10%) for 120 V; 400 W (+5%/-10%) for 230 V
Maximum Temperature	Approx. 130 °C (266 °F) when heating, maintains between 100 and 130 °C
Timer	20, 40 or 60 minutes
Delayed Start Function	Yes, adjustable in 30-minute increments up to 24 hours
Display	LED: temperature in °F and remaining time
Lid	Double-walled insulated, with child safety lock
Aromatherapy	Rotating compartment for scented tablet
Included Accessories	4 removable hooks, user manual
Indicator Lights	Green (temperature < 60°C), red (temperature > 60°C), flashing while heating
Error Codes	E01 (NTC open), E02 (no heating)
Safety	Automatic shut-off at end of cycle, overheat protection, do not use outdoors
Maintenance	Unplug before cleaning; wipe with a damp cloth; do not immerse
Repairability	Do not disassemble yourself; contact Vevor after-sales service

Frequently Asked Questions - HSTW-12 Vevor

How to turn on the Vevor HSTW-12 towel warmer bucket?

Plug in the device, then press the ON/OFF button. The LED screen lights up and displays the ambient temperature if above 60°C, otherwise it stays in standby. Press again to start heating.

How to set the heating timer?

Press the TIME button to cycle through durations: 20, 40 or 60 minutes. The selection blinks and is confirmed after 5 seconds of inactivity.

How to use the delayed start function?

Press the DELAY button to enter delayed mode. Set the delay in 30-minute increments (up to 24 h) by pressing repeatedly or holding the button. Once the delay elapses, heating starts automatically.

Can I add fragrance to the bucket?

Yes, the bucket has an aromatherapy compartment on the lid. Turn it counterclockwise to open, insert a scented tablet, then close by turning clockwise.

How to clean the towel warmer?

Always unplug the device before cleaning. Use a soft damp cloth to wipe exterior surfaces. Never immerse the device in water and avoid abrasive cleaners.

What does error code E01 on the screen mean?

Code E01 indicates a temperature sensor (NTC) open circuit. The device stops and all LEDs flash. Unplug it and contact Vevor after-sales service for repair.

What does error code E02 mean?

Code E02 means the temperature does not rise after 1 minute of heating. This may be due to a faulty connection. Unplug the device and contact Vevor support.

What are the dimensions and weight of the HSTW-12?

The product measures 320 x 320 x 470 mm and weighs approximately 4.2 kg. It can hold up to two large bath towels or one blanket.

What is the electrical power of the towel warmer bucket?

Power varies by version: 450 W for 120 V model (North America) and 400 W for 230 V model (Europe/Australia).

Is it safe to leave the device unattended?

It is not recommended to leave the device unattended, especially with children or pets. Use the timer for automatic shut-off and follow the safety instructions in the manual.

USER MANUAL HSTW-12 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

TOWEL WARMER BUCKETS

MODEL: HSTW-12

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands, and do not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

	Warning-To reduce the risk of injury, user must read instructions manual carefully.READ ALL INSTRUCTIONS BEFORE USEAll the safety and operating instructions should be read adhered to and followed before the unit is operated.
FC	This device complies with Part 15 of the FCC Rules. is subject to the following two conditions:(1) This device not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
	This product is subject to the provision of European D 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products as such may not be discarded with normal domestic w must be taken to a collection point for recycling electric electronic devices

SAFETY & WARNINGS

WARNING: To reduce the risk of electric shock, or serious injury to persons when using the appliance, follow basic precautions including the following: Read all instructions before using the appliance.

Read all instructions before using the appliance.

• To reduce the risk of electric shock, burns, fire, or injury: - Do not use this appliance for anything other than its intended use. - Do not place or store the unit where it can fall or be pulled into a tub or sink. - Do not place in or drop into water or other liquid.

• Do not reach for a unit that has fallen into water. Unplug it immediately.
• Care should be taken so that objects do not fall into and liquids are not spilled onto the unit.
• Close supervision is necessary when this unit is used near children or disabled persons.
• Use this unit only for its intended use as described in this manual.
• Never operate this unit if it has a damaged cord or plug, if it is not working properly, or if it has been
• dropped, damaged, or dropped in water.
• Keep cords away from heated surfaces. Do not wrap the cord around the exterior of the appliance or let
• the cord hang over the edge of a table or counter.
• Do not use outdoors.
• Do not alter the safety plug or use an extension cord with this device.
• Do not operate with a voltage converter.
• Do not touch hot surfaces.
• Do not use accessory attachments not recommended by the manufacturer as this may cause injuries.

PRODUCT PARAMETERS

Model	HSTW-12
District	North America	Europe	Australia
Voltage	AC 120V 60Hz	AC 230V 50/60HZ
Wattage	450W (+5%~-10%)	400W (+5%~-10%)
Capacity	20L
Net Weight	4.2kg
Product Size	320*320*470mm

PACKING LIST

NO.	ACCESSORY NAME	QUANTITY
1	Towel Warmer Buckets	1 pc
2	Hook	4 pcs
3	User Manual	1 pc

INSTRUCTIONS

1. BUTTON CONTROL

1.1 Switch button: opens and closes the towel bucket. 1.2 Time key: selects the heating timing time. 1.3 Delay key: selects the delay time.

2. DELAYED HEATING FUNCTION

1. When the machine is turned on, press the delay button to enter delay mode. Press the delay button to adjust the delay time in 30-minute increments, up to a maximum of 24 hours.
2. When the delay button is pressed, the LED round light above it flashes.
3. At any time, if the delay reservation button is pressed, the reservation time will be executed first, and then heating will be performed.
4. After the heating work is completed, reset the delay time and re-enter

the delay heating mode.

1. During the heating process, if the delay function is operated, the delay is executed first and then reheating occurs.
2. When you press and hold without releasing, the reservation time changes at a rate of 2-3 times per second.

The time of the first long press will be accumulated, and the time will be decreased by releasing the hand again, and the time will be accumulated again, etc.

3. HEATING COUNTDOWN FUNCTION

1. After the delay time is over, heat according to the set heating time, which defaults to 20 minutes.
2. Press the time key to enter the heating time setting mode. Press the key to adjust the delay time in 20-minute increments, with a maximum selection of 20-40-60.
3. When the time button is pressed, the LED round light above it flashes. After flashing for 5 seconds without any operation, the option is confirmed.
4. During the heating process, operate the time key to reset the heating time.
5. At each operation time, the LED lights up corresponding to the timer.
6. After starting heating, increase the temperature to 266 °F for the minutes and maintain the temperature at 215-266 °F.
7. If the timer is more than 20 minutes, after more than 20 minutes enter the heat preservation state and keep the temperature at 180-215 until the timer expires.

1. After power on, light up all LEDs for 3S self-test.
2. In standby mode, press the power button to wake up the CPU, a LED screen flashes waiting for input instructions.

Except for the rest of the standby state, press the power button and program will first detect the temperature. When the temperature is greater than 60° , the real-time temperature will be displayed. When it is lower than 60° , the screen will turn off and enter standby.

5. Temperature display

After pressing the Power Button, the temperature is displayed in Fahrenheit (°F)

6. Working LED indication

1: When the product is powered on and the temperature of the tower bucket wall is lower than 60° , the green light appears;

2: If the temperature of the towel bucket wall is greater than 60° , the light will turn on;

3: When the heating time is over and the temperature in the barrel is lower than 50° C, turn off the light;

4: There is a horizontal light between the time and temperature, which flashes slowly when heating and stays on when not heating.

1. Press the child lock switch to open the flip cover.
2. Aromatherapy box : can be opened and removed by turning counterclockwise, and installed by turning clockwise.
3. Removable hook.
4. Side handles.
5. The power cord case can be stored at the bottom.

FAILURE ANALYSIS

1. The NTC is open circuit. After turning on the heating for 1 minute, the program is locked, the heating relay is disconnected, the fault code E is displayed on the screen, and all LEDs flash, and the buttons do not respond.
2. Without heating, the temperature does not change after 1 minute of power on, the program is locked, the heating relay is disconnected, the fault code E02 is displayed on the screen, and all LEDs flash, and buttons do not respond.

Measures: Unplug the plug, contact the dealer to return to the factory for repair.

Do not disassemble parts by yourself.

1. Performance: The screen displays fault code E02, and all LEDs are blinking, no response to touch.

Reason: The wire is not connected. After heating for 1 minute, the temperature does not change.

Measures: Unplug the plug, contact the dealer to return to the factory for repair.

Do not disassemble parts by yourself.

INSTALLATION AND MOVEMENT

• The generous cavity has the capacity to hold two large bath towels and one personal throw blanket. The simple, single-touch controls provide you with up to 60 minutes of warming.
• Add a fresh, odor-neutralizing scent to your towels and blankets by inserting the aromatherapy tablet into the disc holder.
• The double walled insulated lid keeps heat in while remaining cool to the touch.

POLARIZED PLUG

This appliance has a polarized plug (one blade is wider than the other).

This plug will fit in a polarized outlet only one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

SET UP

1. Open the lid and remove any packaging contents.
2. Place the towel warmer on a dry, level, hard surface.
3. Insert the plug into a standard outlet.

FCC INFORMATION

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

• - Increase the separation between the equipment and receiver.
• - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

Manufacturer: Shanghai Muxin Muye Youxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, Baoshanqu, Shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centre House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands and do not necessarily mean that all categories of tools offered are covered. We kindly remind you to verify carefully when placing an order with us to ensure you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you if there are any technology or software updates on our product.

INSTALLATION AND MOVEMENT

C/0 YH Consulting Limited Office 147, Centre House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

HANDTUCHWÄRMER-EIMER

MODELL: HSTW-12

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to top brands, and does not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you in advance if there are any technology or software updates on our product.

INSTALLATION AND MOVEMENT

Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Cent

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent estimate of savings you might benefit from buying certain tools with us compared to top brands and does not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when you are placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you if there are any technology or software updates on our product.

INSTALLATION AND MOVEMENT

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent estimate of savings you might benefit from buying certain tools with us compared to top brands and does not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when you are placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

6. Working LED indication

INSTALLATION AND MOVEMENT

Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am M

UK

REP

YH CONSULTING LIMITED.

C/0 YH Consulting Limited Office 147, Cent

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and e-Warranty Certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

HAND DUCK WARMER BUCKETS

MODEL: HSTW-12

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands, and do not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you in advance if there are any technology or software updates on our product.

INSTALLATION AND MOVEMENT

C/O YH Consulting Limited Office 147, Cent

Houses London Road, Otkinos, New Thames

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands and does not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

INSTALLATION AND MOVEMENT

C/O YH Consulting Limited Office 147, Cent

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price" or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to top brands, and does not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

MODEL: HSTW-12

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you if there are any technology or software updates on our product.

INSTALLATION AND MOVEMENT

Imported in Australia: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

C/O YH Consulting Limited Office 147, Centre House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE