SP 11.000 Dirt - Pumps Kärcher - Free user manual and instructions

Product type	Pump for dirty water
Brand	Kärcher
Model	SP 11.000 Dirt
Mains voltage	230-240 V
Mains frequency	50 Hz
Nominal power	400 W
Max flow rate	11 000 l/h
Max pressure	0.07 MPa (0.7 bar)
Max delivery head	7 m
Max immersion depth	7 m
Permissible liquid temperature	5 to 35 °C
Max particle size of transported fluids	20 mm
Minimum liquid height (manual mode)	60 mm
Residual water height	25 mm
Weight (without accessories)	4.4 kg
Main features	Float switch, Quick-Connect, automatic air bleed
Permitted transported fluids	Fresh water up to 20 mm particles, pool water, detergent solution
Protection	Thermal circuit breaker against overheating, dry running protection
Maintenance	Rinse with clean water after use, clean suction area
Storage	Frost protection, device completely emptied

Frequently Asked Questions - SP 11.000 Dirt Kärcher

What to do if the pump does not start or stops during operation?

Check the power supply (fuses, socket). If the thermal circuit breaker has tripped, disconnect, let it cool down and clean the suction area. Also check the position of the float switch.

Why is the flow rate low or decreasing?

This may be due to a blocked suction area, too high delivery head, a hose that is too long or too small in diameter, or a partially closed valve. Clean the suction and optimize the circuit.

The pump runs but does not transport water, why?

Air in the pump: check the commissioning. Clean the suction area if particles block it. In manual mode, the liquid level must be sufficient.

Can I use the pump with very dirty water?

Yes, up to a particle size of 20 mm. For larger particles, use a pre-filter. After use, rinse the pump with clean water.

What is the minimum residual water height?

In manual mode, the pump can pump down to 25 mm residual water height. Fold the support feet to achieve this height.

Is it possible to run the pump continuously?

No, the device is not designed for continuous operation without interruption. Avoid prolonged cycles such as continuous circulation in a pond.

How to maintain the pump?

After each use, especially with dirty water or additives, rinse the pump with clean water. Clean the outside with a soft cloth. Empty and dry the device before storage.

What to do if the Quick-Connect does not open?

The system may be blocked by dirt. Remove the clip and clean it. Make sure the connection sleeve is clear.

Can I use the pump in winter during frost?

No, do not operate the pump during frost and protect it from frost. Store it in a frost-free place, completely emptied.

What types of liquids can I pump?

Fresh water, pool water (with dosed additives), detergent solutions. Prohibited: explosive, flammable, corrosive liquids, fats, oils, salt water, toilet wastewater.

USER MANUAL SP 11.000 Dirt Kärcher

Deutsch 4

English 8

Français 13

Italiano 18

Nederlands 23

Español 28

Português 33

Dansk 38

Norsk 43

Svenska 47

Suomi 52

Ελληνικά 56

Türkçe 61

Русский 66

Magyar 72

Czech 77

Slovenian 81

Polish 86

Romanian 91

Slovak 96

Croatian 101

Serbian 106

Bulgarian 110

Estonian 115

Latvian 120

Lithuanian 125

Ukrainian 129

Japanese 134

Kazakh 139

Arabic 145

A

Contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Contents

General notes.... 8

Intended use 9

Hazard levels 9

Environmental protection 9

Accessories and spare parts.... 9

Scope of delivery.... 9

Warranty....9

Description of the device.... 9

Initial startup.... 10

Operation 10

Care and maintenance.... 11

Transport.... 11

Storage.... 11

Troubleshooting guide.... 11

Technical data 12

Optimising the flow rate.... 12

Declaration of Conformity.... 12

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first

time. Proceed accordingly.

Keep both books for future reference or for future owners.

Intended use

Only use the device in private households.

Intended use:

• Removal of water from building sections in the event of flooding • Transferring and pumping water from containers • Water removal from wells and shafts
• Pumping fresh water out of boats and yachts

For notes on functional principle, see chapter Operation.

Permissible feed fluids

⚠️DANGER

Danger of death and risk of damage when pumping explosive, flammable or unsuitable substances!

Flammable or explosive substances may ignite or explode.

Unsuitable substances can damage the pump.

Do not pump explosive, flammable or corrosive liquids or gases (e.g. fuels, petroleum, nitro thinner) and do not pump fats, oils, salt water or waste water from sanitary facilities or water that has a lower flowing ability than clean water.

Permissible feed fluids:

• Fresh water up to the specified degree of contamination Water with a degree of contamination up to a diameter of 20 mm Water with a degree of contamination up to a diameter of 5 mm
• Swimming pool water with intended dosage of additives
• Washing lye, e.g. from leaking washing machines. Afterwards, rinse and clean the pump with clear fresh water, see chapter Rinsing and cleaning.
• The temperature of the feed fluids should lie between 5 °C and 35 °C.

SP 9,500 Dirt and SP 11,000 Dirt (dirty water pump):

SP 9,000 Flat (clean water pump):

Improper use

ATTENTION

Risk of damage due to frost!

Operation during frost may damage the device.

An incompletely emptied device can be damaged by frost.

Do not operate the device during frost.

Protect the device from frost.

ATTENTION

Risk of damage during continuous operation!

The device is not suitable for continuous operation.

Do not operate the device continuously for long periods (e.g. continuous circulation operation in ponds) or as a stationary installation (e.g. as a water lifting system, fountain pump).

Note

The manufacturer accepts no liability for possible damage caused by improper use or incorrect operation.

Hazard levels

DANGER

Indication of an imminent threat of danger that will lead to severe injuries or even death.

WARNING

Indication of a potentially dangerous situation that may lead to severe injuries or even death.

CAUTION

Indication of a potentially dangerous situation that may lead to minor injuries.

ATTENTION

Indication of a potentially dangerous situation that may lead to damage to property.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can

pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Notes on the content materials (REACH)

Current information on content materials can be found at: www.kaercher.de/REACH

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Warranty

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

(See overleaf for the address)

Description of the device

See graphics page for illustrations Illustration A

① Carrying handle ② Power supply cable with plug ③ Lock (float switch) ④ *Pump connecting piece G 1 (3/4" and 1" hose connection and G 1 - thread) ⑤*Check valve ⑥ G 1 - threaded connection

⑦ Pump connecting piece G 1 ½ (1", 1 ¼" and 1 ½" hose connection and G 1 ½ - thread) ⑧ Pipe union (G 1 ½ - thread) ⑨ Float switch ⑩ Quick-Connect ⑪ Automatic venting device ⑫Feet (SP 9,000 Flat)

*Not included in the scope of delivery.

Initial startup

⚠️DANGER

Risk of electric shock and risk of injury!

The device contains electrical and mechanical components.

Always disconnect the device from the power supply before assembling, disassembling or cleaning.

Note

The shorter the hose length and larger the hose diameter, the higher the pump capacity.

To avoid clogging the pump, use a pre-filter for hose diameters smaller than 1 1/4".

The pump connection is equipped with a plug-in system (Quick-Connect).

The pipe union with pump connecting piece G 1 1/2 and the G 1 threaded connection are supplied unassembled with the device.

Note

Hoses with a diameter of 1", 1 1/4" and 1 1/2" can be connected to the pump connecting piece G 1 1/2.

A sufficiently large hose diameter must be selected and the pump connecting piece G 1 1/2 must be shortened according to the grooves so that the required particle size can be used. A large hose diameter is also recommended for smaller particle sizes to allow a high flow volume.

Connect hose to pump if using a 1", 1 1/4" or 1 1/2" hose:

1 Screw the pump connecting piece G 1 1/2 onto the pipe union.

Illustration B

2 Push the hose clamp onto the hose.

3 Push the hose onto the pump connecting piece G 1 1/2 and fasten it with a hose clamp.

4 Push the pipe union into the Quick-Connect. Illustration C

Connect hose to pump if using a 3/4" or 1" hose:

1 Screw the G1 threaded connection onto the pipe union.

Illustration B

2 Fit the special accessory pump connecting piece G 1 (6.997-359.0 pump connecting piece G 1 (33.3 mm) incl. check valve - not included in the scope of delivery) onto the G 1 threaded connection: a Place the check valve on the G 1 threaded connection so that the lettering 'UP' is legible. b Screw the pump connecting piece G 1 onto the G 1 threaded connection. 3 Push the hose clamp onto the hose. 4 Push the hose onto the pump connecting piece G 1 and fasten it with a hose clamp. 5 Push the pipe union into the Quick-Connect. Illustration C

Setting up / immersing the pump:

1 Fold out or in the feet (SP 9,000 Flat).

Illustration D

2 Place the pump securely on solid ground in the feed fluid or immerse it by means of a rope attached to the carrying handle.

Note

The suction area must not be blocked by contamination. If the ground is muddy, place the pump on a brick or something similar. Make sure that the pump is horizontal. Do not carry the pump using the cable or hose.

Operation

DANGER

Danger of death from electric shock.

Danger of death from electric shock if live parts are touched.

During operation, do not touch the rope attached to the carrying handle or any objects that are in contact with the pumped liquid (e.g., pipelines protruding into the pumped liquid, railings) and do not reach into the pumped liquid.

Automatic venting device

1. If the fluid level is low, any sucked-in air, or air present in the pump, may escape via the automatic venting device. Fluid can also leak along with air. If the pump has problems with suction when the fluid level is low, unplug and plug in the mains plug repeatedly to assist the suction process.

Illustration E

Automatic mode

1. If necessary, fold out the feet, see chapter Initial startup (SP 9,000 Flat).

Note

Folding out the feet is not absolutely necessary, but it does increase the pump capacity.

1. Plug the mains plug into a mains socket.

Note

In automatic mode, the float switch controls the pumping process automatically.

The pump switches on as soon as the float switch has reached the switch-on height caused by the rising fluid level.

The pump switches off as soon as the float switch has reached the switch-off height caused by the sinking fluid level.

The float switch must be able to move freely.

Illustration F

Min / Max SP	9,000 Flat	SP 9,500 Dirt	SP 11,000 Dirt
Switch-on height cm*	36 / 44 43 / 50	43 / 50
Switch-off height cm*	15 / 24 18 / 30	18 / 30

* The switching heights vary depending on the position of the float switch.

Manual operation

Note

In manual operation, the pump stays switched on continuously. For the pump to suction itself in manual mode, the fluid level must be at least 60 mm (SP 9,500 Dirt and SP 11,000 Dirt) or 7 mm (SP 9,000 Flat).

Note

The pump can pump up to a residual fluid height of 25 mm (SP 9,500 Dirt and SP 11,000 Dirt) or 1 mm (SP 9,000 Flat).

The specified residual fluid heights are only achieved in manual operation.

The float switch must be able to move freely.

1. Fold in the feet, see chapter Initial startup (SP 9,000 Flat).

Note

By folding in the feet, flat suction of the fluid up to 1 mm residual fluid height is possible in manual operation.

1. Fasten the float switch in the lock so it points upwards.

Illustration G

ATTENTION

Risk of damage from dry running!

Dry running leads to increased wear on the pump.

Do not leave the pump unattended in manual operation. In case of dry running, immediately pull the mains plug out of the socket.

1. Plug the mains plug into a mains socket.

Finishing operation

1. Pull the mains plug out of the socket. The device stops.

ATTENTION

Risk of damage!

Risk of damage due to dried soiling or additives.

Rinse and clean the device immediately after each use.

1. If dirty liquids or liquids with additives have been pumped, rinse and clean the device immediately after finishing operation, see chapter Rinsing and cleaning.
2. Drain the device and accessories and let them dry.

Care and maintenance

⚠️DANGER

Risk of electric shock and risk of injury!

The device contains electrical and mechanical components.

Cleaning and user maintenance may not be carried out by children.

Rinsing and cleaning

ATTENTION

Risk of damage!

Risk of damage due to dried soiling or additives.

Rinse and clean the device immediately after each use.

1 If dirty liquids or liquids with additives have been pumped, the device must be rinsed afterwards: Use the device to pump clear fresh water without additives until all soiling or additives have been flushed out of the device.

⚠️DANGER

Risk of electric shock and risk of injury!

The device contains electrical and mechanical components.

Always disconnect the device from the power supply before assembling, disassembling or cleaning.

2 Pull the mains plug out of the socket.

3 Press the Quick-Connect button and remove the connection nozzle.

Illustration C

4 Where necessary, remove residue from the hose and on Quick-Connect.

5 Clean the outside of the device with a soft, clean cloth and clear fresh water.

6 Drain the device and accessories and let them dry.

Service

The device is maintenance-free.

Transport

Manual transport

△CAUTION

Risk of injury from tripping!

There is a risk of injury from tripping on loose cables and hoses.

Be careful of cables and hoses when moving the device.

1. Lift and carry the device by the carrying handle.

Transport in vehicles

⚠ WARNING

Risk of injury, risk of damage!

Note the weight of the device during transport.

Store or secure the device in accordance with applicable guidelines so that it cannot slip or be thrown around during transport.

1. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respectively applicable guidelines.

Storage

ATTENTION

Risk of damage due to frost!

An incompletely emptied device can be damaged by frost.

Completely empty the device and accessories before storing them.

Protect the device from frost.

Store the device in a frost-free place and not outdoors.

△CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

1. Completely empty the pump and accessories.
2. Allow the pump and accessories to dry out.
3. Store the pump in a frost-protected place.

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

Fault Cause Rectification
Pump is running, but not delivering	Air is in the pump. 1. Check for correct startup (see chapter Initial startup and Operation).
	Dirt particles block the suction area. 1. Pull the mains plug out of the socket.2. Clean the suction area.
	The fluid level is too low (manual operation), see chapter Technical data.	1. Immerse the pump deeper into the feed fluid, see chapter Manual operation.

Fault Cause Rectification
The pump does not start or stops during operation	The power supply is disconnected. 1. Check the fuses and the electrical connections.
	The thermal protection switch has switched off the pump because of overheating.	1. Pull the mains plug out of the socket.2. Allow the pump to cool down.3. Clean the suction area.4. Prevent the pump from running dry.
	Dirt particles are trapped in the suction area.	1. Pull the mains plug out of the socket.2. Clean the suction area.
	The float switch switches the pump off. 1.	Automatic mode: Check the position and free movement of the float switch and correct if necessary, see chapter Automatic mode.2. Manual operation: Attach the float switch correctly, see chapter Manual operation.
The pump capacity drops or is too low	The suction area is clogged. 1. Pull the mains plug out of the mains socket and clean the suction area.
	The delivery rate of the pump depends on the delivery head and the connected periphery.	1. Observe the maximum delivery height, see chapter Technical data. If necessary, select a larger hose diameter or shorter hose length.
	The cross-section on the pressure side is narrowed, e.g. due to the valve/ball tap not being fully open.	1. Fully open the valve / ball tap.
	The pressure side hose is kinked. 1. Eliminate the kink points in the hose.
Quick-Connect cannot be opened	The Quick-Connect plug system is blocked by contamination.	1. Remove the clip and clean it.

Technical data

		SP9.000Flat	SP9.500Dirt	SP11.000Dirt
Device performance data
Mains voltage V	230-240	230-240	230-240
Power frequen-cy	Hz 50	50	50
Nominal power W		280	280	400
Maximum flow rate	l/h	9.000	9.500	11.000
Solids content in water	kg/m 3	>2,5	>2,5	>2,5
Pressure (max.)	MPa(bar)	0,06(0,6)	0,06(0,6)	0,07(0,7)
Delivery height (max.)	m	6	6	7
Immersion depth (max.)	m	7	7	7
Perm. temp. feed fluid	°C	5...35	5...35	5...35
Particle size (max.) of permissible feed fluids	mm	5	20	20
Minimum fluid level (manual mode)	mm	7	60	60
Residual fluid height	mm	1	25	25

	SP9.000Flat	SP9.500Dirt	SP11.000Dirt
Weight (without kg accessories)	3,7	3,8	4,4

Subject to technical modifications.

Optimising the flow rate

The flow rate is further increased:

• The lower the delivery height is. • The greater the diameter of the hose used is. • The shorter the hose used is. - The smaller the pressure loss caused by the connected up accessories.

Declaration of Conformity

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health re-

quirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: Pump

Type: 1.645-xxx

Currently applicable EU Directives

2014/35/EU

2014/30/EU

2011/65/EU

2009/125/EC

Commission Regulation(s)

(EU) 2019/1781

Harmonised standards used

EN 60335-1

EN 60335-2-41

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

The signatories act on behalf of and with the authority of the company management.

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Declaration of Conformity (UK)

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

Product: Pump

Type: 1.645-xxx

Currently applicable UK Regulations

S.I. 2016/1101 (as amended)

S.I. 2016/1091 (as amended)

S.I. 2012/3032 (as amended)

S.I. 2010/2617 (as amended)

Commission Regulation(s)

(EU) 2019/1781

Designated standards used

EN 60335-1

EN 60335-2-41

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

The signatories act on behalf of and with the authority of the company management.

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Table of contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01/06/2021

Contents

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01/06/2021

Index

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

SP 9.000 Flat (clean water pump):

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Contents

General notes.... 43

Optimize the flow rate 47

Optimize the flow rate

Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 2021/06/01

Contents

General information 47

D-71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.06.2021

Contents

General instructions 52

S. Reiser Manager Regulatory Affairs & Certification

Documentation officer: S. Reiser

Alfred Kärcher SE & Co. KG Alfred-Kärcher-Str. 28 - 40 71364 Winnenden (Germany) Phone: [phone] Fax: [phone] Winnenden, 1.6.2021

Table of Contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Table of Contents

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Winnenden, 2021/06/01

Table of Contents

General instructions 66

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Winnenden, 2021/06/01

Contents

General instructions 77

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Winnenden, 2021/06/01

Index

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Winnenden, 1. 6. 2021

Table of contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Relevant EU Directives

2014/35/EU

2014/30/EU

2011/65/EU

2009/125/EU

Regulation(s) used

(EU) 2019/1781

Harmonized standards applied

EN 60335-1

EN 60335-2-41

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 2015

EN 61000-3-2: 2014

EN 61000-3-3: 2013

EN IEC 63000: 2018

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Table of Contents

General notes 96

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.06.2021

Contents

General notes 101

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Authorized representative for documentation:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.06.2021.

Contents

Opšte napomene	106
Namenska upotreba	106
Stepeni opasnosti	106
Zaštita životne sredine	106
Pribor i rezervni delovi	106
Obim isporuke	106
Garancija	106
Opis uređaja	106
Puštanje u pogonl	107
Rad	107
Nega i održavanje	108
Transport	108
Skladištenje	108
Otklanjanje smetnji	108
Tehnički podaci	109
Optimizacija količine protoka	110
EU izjava o usklađenosti	110

General notes

Before first use, read the original operating instructions and the enclosed safety instructions. Follow

them accordingly.

Keep both booklets for future use or for the next owner.

Intended use

Use the device exclusively for private household use. Intended use:

• draining water in parts of buildings during floods
• pumping and emptying tanks
• taking water from wells and shafts
• Pumping fresh water from ships and yachts. For notes on the operating mode, see the chapter on Operation.

Permitted working fluids

⚠ DANGER

Danger to life and risk of damage when transporting explosive, flammable, or unsuitable materials!

Flammable or explosive materials can ignite or explode.

Unsuitable materials can damage the pump. Do not transport explosive, flammable, or corrosive liquids or gases (e.g., fuels, petroleum, nitro thinner) nor greases, oils, salt water, or wastewater from toilets, or water with a lower flow capacity than clean water.

Permitted working fluids:

• Fresh water up to the specified contamination level SP 9.500 Dirt and SP 11.000 Dirt (wastewater pump): Water with contamination level up to grain size 20 mm. SP 9.000 Flat (clean water pump): Water with contamination level up to grain size 5 mm.
• Bases even when additives are dosed as intended.
• Water with dissolved detergent, e.g., from washing machines. Then rinse the pump with clean fresh water and clean it, see the chapter on Rinsing and Cleaning.
• The temperature of the working fluids must be between 5 °C and 35 °C.

Non-intended use

CAUTION

Documentation authorized by:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 2021/06/01

Table of contents

General notes 110

Intended use 110

Hazard levels.... 111

Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2021/06/01

Table of Contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel: [phone]

Winnenden, 2021/06/01

Table of Contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Authorized Representative:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Phone: [phone]

Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Hose.

THANK YOU!

THANK YOU! THANKS! THANKS!

Register your product and benefit from many advantages.

www.kaercher.com/welcome

Rate your product and tell us your opinion.

www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28-40

71364 Winnenden (Germany)