K 7 WCM Premium - Pressure washer Kärcher - Free user manual and instructions

Product type	High-pressure cleaner
Brand	Kärcher
Model	K 7 WCM Premium
Operating pressure	15 MPa (150 bar)
Maximum permissible pressure	18 MPa (180 bar)
Water flow rate	9.2 l/min
Maximum flow rate	10 l/min
Detergent flow rate	0.3 l/min
Connected load	3.0 kW
Supply voltage	230 V ~ 1 phase, 50 Hz
Main fuse	16 A (slow-blow)
Protection type	IPX5
Protection class	I
Operating weight	19.3 kg
Dimensions (L × W × H)	394 × 369 × 946 mm
Max. supply temperature	60 °C
Max. supply pressure	1.2 MPa
Max. suction height	0.5 m
Hand-arm vibrations	2.3 m/s²
Sound pressure level	75 dB(A)
Sound power level	91 dB(A)
Main functions	Vario Power lance (adjustable pressure), Rotabuse lance, Auto-Stop function, Motor thermal protection
Scope of delivery	High-pressure gun, Vario Power lance, Rotabuse lance, high-pressure hose, hose reel, transport handle
Safety	Gun lock, main switch, automatic shut-off, thermal protection
Maintenance	Cleaning of water inlet filter and detergent filter

Frequently Asked Questions - K 7 WCM Premium Kärcher

How to bleed air from the unit after first use?

Turn on the unit without a lance connected for a maximum of 2 minutes. Press the gun until water comes out without bubbles. Then connect the lance.

Which lance to use for stubborn dirt?

Use the Rotabuse lance (rotary nozzle) for stubborn dirt. For everyday tasks, prefer the Vario Power lance.

How to adjust the working pressure?

Release the gun lever and turn the Vario Power lance to the desired position from SOFT to HARD. Detergent is dosed by turning the lance fully to SOFT.

What to do if the unit does not start?

Check the mains voltage, power cable, and gun lever. If the motor is overheated, let it cool for 1 hour after turning off the unit.

Can the unit be used with a water tank?

Yes, with the KÄRCHER suction hose (special accessory ref. 2.643-100). Fill the hose with water, screw it onto the connection and immerse it in the water source. Max. suction height is 0.5 m.

How to maintain the water inlet filter?

Remove the coupling from the water connection, take out the mesh with flat pliers, clean it under running water and put it back. Check that it is not damaged.

Why does the pressure vary?

The high-pressure nozzle may be clogged. Clean it with a pin. Also check the water flow and the condition of the inlet mesh.

How to store the unit in winter?

Completely drain the unit: turn off water, disconnect the hose, run for 1 minute to expel residual water. Store in a frost-free room.

What to do in case of water leak?

A slight leak is normal. If the leak is significant, contact authorized customer service. Do not continue using the unit.

How to use detergent?

Take out the detergent suction hose, immerse it in the solution. Use the Vario Power lance in SOFT position (low pressure). Apply detergent to the dry surface, let it act, then rinse at high pressure.

USER MANUAL K 7 WCM Premium Kärcher

Czech 83

Slovenian 88

Polish 93

Romanian 98

Slovak 103

Croatian 108

Serbian 113

Bulgarian 118

Estonian 124

Latvian 128

Lithuanian 133

Ukrainian 139

Kazakh 144

B

Contents

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

Contents

General notes.... 12

Environmental protection.... 12

Intended use.... 12

Accessories and spare parts 12

Scope of delivery.... 12

Device description 12

Safety devices 13

Symbols on the device 13

Installation 13

Initial startup 13

Operation.... 14

Transport 15

Storage.... 15

Care and service 15

Troubleshooting guide.... 15

Warranty 16

Technical data 16

EU Declaration of Conformity.... 16

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time. Proceed accordingly.

Keep both books for future reference or for future owners.

Keep both books for future reference or for future owners.

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can

pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Cleaning work producing in oily waste water, e.g. washing engines, washing undercarriages etc., may be performed at washing stations with an oil separator.

Working with detergents may only be performed on watertight surfaces with connection to the waste water sewage system. Do not allow detergent to enter waterways or the soil.

Extraction of water from public waterways is not permitted in some countries.

Notes on the content materials (REACH)

Current information on content materials can be found at: www.kaercher.de/REACH

Intended use

Use the high-pressure cleaner in private households only.

The high-pressure cleaner is intended for cleaning machines, vehicles, buildings, tools, façades, terraces, garden machines etc. using a high-pressure water jet.

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

The scope of delivery for the appliance is shown on the packaging. Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Device description

For the illustrations, refer to the graphics page Illustration A

Illustration B

①Transport wheel ② Water connection with integrated sieve ③ Detergent suction hose ④ Mains connection cable with mains plug ⑤ Mains connection cable storage compartment ⑥ Hose reel ⑦ Holder for high-pressure hose ⑧ Spray lance dirt blaster for stubborn soiling ⑨ Vario Power spray lance for common cleaning tasks The working pressure can be continuously increased from "SOFT" to "HARD". To adjust the working pressure, release the trigger gun lever and turn the spray lance to the desired position. Detergent can be added to the water jet when the spray lance is turned all the way in the SOFT direction.

10 High-pressure gun

⑪Button for separating the high-pressure hose from the high-pressure gun

⑫High-pressure gun lever

⑬High-pressure gun lock

⑭ High-pressure hose

⑮Trigger "0/OFF" / "I/ON"

⑯ Storage for spray lance

⑰ Storage for high-pressure hose / mains connection cable

⑱Transport handle

Storage for high-pressure gun

20 Quick coupling for high-pressure connection 21 Type plate 22 Water connection coupling 23 Garden hose (fabric reinforced, diameter at least 1/2 inch (13 mm), length at least 7.5 m, with commercially available quick coupling) 24 KÄRCHER suction hose for water supply from open containers (order no. 2.643-100) 25 Screws 26 High-pressure hose clip

** additionally required

Safety devices

CAUTION

Missing or modified safety devices!

Safety devices are provided for your own protection. Do not bypass, remove or render ineffective any safety devices.

Power switch

The power switch prevents unintentional operation of the device.

High-pressure gun lock

The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.

Auto-stop function

If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.

Motor circuit breaker

The motor circuit breaker shuts off the device if power consumption is too high.

Symbols on the device

Do not aim the high-pressure jet at persons, animals, live electrical equipment, or the device itself.

Protect the device against frost.

The device may not be connected to the public drinking water network.

Installation

For the illustrations, refer to the graphics page.

Fit the supplied loose parts onto the device before starting up the device.

Place the screws provided and matching screwdriver at the ready.

Mounting the transport handle

1. Attach the transport handle.
2. Secure the transport handle with 3 screws.

Illustration C

Mounting the storage option for the high-pressure hose / mains connection cable

1. Insert the storage option for the high-pressure hose / mains connection cable into the holder at the centre of the transport handle.

The storage option locks into place.

Illustration D

Mounting the storage option for spray lances

1. Push the storage option for the spray lances into the holder on the device.
2. Hold the storage option in the end position and secure it with a screw.

Illustration E

Mounting the storage option for the high-pressure gun

1. Push the storage option for the high-pressure gun into the holder on the device.
2. Hold the storage option in the end position and secure it with a screw.

Illustration F

Mounting the storage option for the mains connection cable

Devices without a hose reel

1. Push the storage option for the mains connection cable into the holder on the transport handle.
2. Hold the storage option in the end position and secure it with a screw.

Illustration G

Mounting the high-pressure hose reel

Devices with a hose reel

1. Attach the holder for the hose reel.
2. Secure the holder using 2 screws.

Illustration H

1. Attach the hose reel.

The hose reel locks into place.

Illustration I

Installing the water connection coupling

1. Screw the water connection coupling onto the water connection on the device.

Illustration J

Initial startup

Note

Take care not to exceed the maximum permissible mains impedance at the connection point (see chapter Technical data).

Contact your electricity supplier in the case of any uncertainties regarding the mains grid impedance at your electrical connection point.

1. Place the device on a flat and level surface.
2. Unwind the high-pressure hose and eliminate any loops and twists.

Note

Devices with a hose reel: During operation, the high-pressure hose must be completely unwound from the hose reel. 3. Insert the high-pressure hose into the high-pressure gun until it audibly latches into place.

Illustration K

Note

Take care to ensure the correct alignment of the nipple. 4. Insert the high-pressure hose into the quick coupling until it audibly latches into place.

Illustration L

1. Check for a secure connection by pulling on the high-pressure hose.
2. Plug the mains plug into a mains socket.

Water supply

For the connection values, see the type plate or chapter Technical data.

Observe the water distribution company regulations.

ATTENTION

Damage through contaminated water

Contamination in the water can damage the pump and the accessories.

KÄRCHER recommends using the KÄRCHER water filter for protection (special accessory, order number 4.730-059).

Connection to the water line

ATTENTION

Hose coupling with Aquastop on the water connection of the device

Damage to the pump

Never use a hose coupling with Aquastop on the water connection of the device.

You can use an Aquastop coupling on the tap.

1. Plug the garden hose onto the water connection coupling.
2. Connect the garden hose to the water line.

Illustration M

1. Open the water tap fully.

Sucking water from open containers

When used with the KÄRCHER suction hose with check valve (special accessory, order number 2.643-100), this high-pressure cleaner is suitable for sucking up surface water, e.g. from rain barrels or ponds (for the maximum suction height, see chapter Technical data).

The water connection coupling is not required for vacuuming operation.

1. Fill the suction hose with water.
2. Screw the suction hose onto the device water connection and hang it in a water source (e.g. water butt).

Vent the device

1. Switch the device on "I/ON".
2. Unlock the lever of the high-pressure gun.
3. Press the lever of the high-pressure gun. The device switches on.
4. Allow the device to run for a maximum of 2 minutes until the water escaping from the high-pressure gun is free of air bubbles.
5. Release the lever of the high-pressure gun.
6. Lock the lever of the high-pressure gun.

Operation

ATTENTION

Pump running dry

Damage to the device

If pressure does not build up in the device after 2 minutes, then switch the device off and proceed according to the instructions in the chapter Troubleshooting guide.

High-pressure operation

ATTENTION

Damage to painted or sensitive surfaces

Surfaces can be damaged when the jet is too close to the surface or an unsuitable spray lance is used.

Maintain a minimum spray distance of 30 cm when cleaning painted surfaces.

Do not clean car tyres, paint or sensitive surfaces such as wood with the dirt grinder.

1. Insert a spray lance into the high-pressure gun and lock it by turning it 90°.

Illustration N

1. Switch the device on ("I/ON").
2. Unlock the lever of the high-pressure gun.
3. Press the lever of the high-pressure gun. The device switches on.

Operation with detergent

⚠️DANGER

Failure to adhere to the safety data sheet

Incorrect handling of the detergent can seriously damage your health

Observe the safety data sheet of the detergent manufacturer, in particular the instructions on personal protective equipment.

Note

KÄRCHER detergents ensure fault-free operation. Ask us for a consultation, request our catalogue or our detergent information sheets.

Note

Detergent can only be mixed into the jet at low pressure.

1. Pull the desired length of the detergent suction hose out of the casing.

Illustration O

1. Hang the detergent suction hose in a container with detergent solution.
2. Use the Vario Power spray lance.
3. Turn the spray lance all the way into the "SOFT" position. The detergent solution is mixed with the water jet during operation.

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.

After operation with detergent

1. Flush the device with clear water for approx. 30 seconds.

Interrupting operation

1. Release the lever of the high-pressure gun. The device switches off when the lever is released. The high pressure in the system is retained.
2. Lock the lever of the high-pressure gun.

Illustration P

1. Switch the device off "0/OFF" during work breaks longer than 5 minutes.

Ending operation

△CAUTION

Pressure in the system

Injuries from high-pressure water escaping uncontrollably

Only disconnect the high-pressure hose from the high-pressure gun or the device when the system is fully depressurised.

1. Release the lever of the high-pressure gun.
2. Close the water tap.
3. Press the lever of the high-pressure gun for 30 seconds.

The pressure remaining in the system is discharged.

1. Release the lever of the high-pressure gun.
2. Lock the lever of the high-pressure gun.
3. Disconnect the device from the water supply.
4. Switch off the device "0/OFF".
5. Pull the mains plug out of the socket.

Transport

⚠CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transportation.

Pulling the device

1. Pull the device via the transport handle.

Transporting the device in a vehicle

1. Secure the device against slipping and tipping over.

Storage

△CAUTION

Risk of injury and damage!

The device may tip over on sloping surfaces.

Be aware of the weight of the device during storage.

Storing the device

1. Place the device on a level surface.
2. Disconnect the spray lance from the high-pressure gun.
3. Press the separation button on the high-pressure gun and disconnect the high-pressure hose from the high-pressure gun.
4. Press the casing of the high-pressure hose quick coupling in the direction of the arrow and pull out the high-pressure hose.
5. Stowing the high-pressure hose. Devices without a hose reel: Store the high-pressure hose on the device. Devices with a hose reel: a) Insert one end of the high-pressure hose into the opening at the front of the hose reel. b) Turn the crank to wind up the high-pressure hose. c) While doing so, guide the high-pressure hose with the second hand.

Illustration Q

d) Fasten the coiled high-pressure hose to the hose reel with the high-pressure hose clip.

Illustration R

1. Stow the mains connection cable on the device.
2. Stow both spray lances and the high-pressure gun in the appropriate storage options.

Observe the additional instructions before storing the device for a longer period of time, see chapter Care and service.

Frost protection

ATTENTION

Danger of frost

Incompletely emptied devices can be destroyed by frost.

Completely empty the device and accessories.

Protect the device from frost.

The following requirements must be satisfied:

• The device is disconnected from the water supply. • The high-pressure hose is removed.
• Switch the device on "I/ON"
• Wait for a maximum of 1 minute until no more water escapes from the high-pressure connection.
• Switch off the device.
• Store the device in a frost-protected room, together with all accessories.

Care and service

⚠️DANGER

Danger of electric shock

Injuries due to touching live parts

Switch off the device.

Remove the mains plug.

The device is maintenance-free, i.e. you do not need to perform any maintenance work.

Clean the sieve in the water connection

ATTENTION

Damaged sieve in the water connection

Damage to the device through contaminated water

Check the sieve for damage before inserting it in the water connection.

If necessary, clean the sieve in the water connection.

1. Remove the water connection coupling.
2. Pull the sieve out.
3. Clean the sieve under running water. Illustration S
4. Insert the sieve into the water connection.

Clean the detergent filter

Clean the detergent filter before longer periods of storage.

1. Pull the filter off the detergent suction hose.
2. Clean the filter under running water.

Illustration T

Troubleshooting guide

Malfunctions often have simple causes that you can remedy yourself using the following overview. When in doubt, or in the case of malfunctions not mentioned here, please contact your authorised Customer Service.

⚠️DANGER

Danger of electric shock

Injuries due to touching live parts

Switch off the device.

Remove the mains plug.

Device not running

1. Press the lever of the high-pressure gun. The device switches on.
2. Check that the voltage specified on the type plate corresponds to the voltage of the power source.
3. Check the mains connection cable for damage.
4. If the motor is overloaded and the motor circuit breaker has triggered: a) Switch off the device "0/OFF". b) Allow the device to cool down for 1 hour. c) Switch the device on "I/ON" and resume operation. Have the device checked by Customer Service if this fault occurs repeatedly.

The device does not start up, the motor buzzes

Voltage drop due to a weak mains grid or when using an extension cable

1. When switching on, first press the lever on the high-pressure gun and then switch on the device "I/ON".

Device does not reach required pressure

The water supply is too low.

1. Open the water tap fully.
2. Check the water inlet for an adequate flow rate.
3. Check the setting at the spray lance.
4. Check that the maximum suction height is not exceeded.

The sieve in the water connection is dirty.

1. Pull the sieve in the water connection out using flat pliers.
2. Clean the sieve under running water. Illustration S

Air is in the device.

1. Vent the device:

a Switch on the device without a connected spray lance for a maximum of 2 minutes.

b Press the high-pressure gun and wait until the water escaping from the high-pressure gun is free of air bubbles.

c Connect the spray lance.

Strong pressure fluctuations

1. Clean the high-pressure nozzle:

a Use a needle to remove dirt from the nozzle drill.

b Rinse the high-pressure nozzle from the front with water.

2. Check the water supply volume.

Device leaking

1. The device leaks a small amount for technical reasons. If the leak is severe, request authorised Customer Service.

Detergent is not sucked in

1. Use the Vario Power spray lance and turn it all the way in the "SOFT" direction.
2. Clean the filter on the detergent suction hose.
3. Check the detergent suction hose for kinks.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

(See overleaf for the address)

Technical data

		K 7 WCM	K 7 WCM Premium
Electrical connection
Voltage	V		230
Phase ~ 1 1
Frequency Hz 50 50
Maximum permissible mains grid impedance	Ω 0,0377 +j0,0236		0,0377 +j0,0236
Power rating	kW	3,0	3,0
Degree of protection		IPX5	IPX5
Protection class		I	I
Power protection (slow-blowing)	A	16	16
Water connection
Feed pressure (max.)	MPa	1,2	1,2
Input temperature (max.) °C		60 60
Input amount (min.)	l/min	12 12
Suction height (max.)	m	0,5	0,5
Device performance data
Operating pressure	MPa	15 15
Max. permissible pressure	MPa	18	18
Water flow rate	l/min	9,2	9,2
Maximum flow rate l/min	10 10
Detergent flow rate	l/min	0,3	0,3

	K 7 WCM	K 7 WCM Premium
High-pressure gun recoil force N	27	27

Dimensions and weights

Typical operating weight	kg	18,8 19,3
Length	mm	355 394
Width	mm	369	369
Height	mm	946 946

Determined values in acc. with EN 60335-2-79

Hand-arm vibration value	m/s2	2,3	2,3
Uncertainty K	m/s2	0,7	0,7
Sound pressure level LpA	dB(A)	75 75
Uncertainty KpA	dB(A)	3 3
Sound power level LWA+ K uncertaintyWA	dB(A)	91 91

Exception according to Regulation (EU) 2019/1781 Annex I Section 2 (12): j)

Subject to technical changes without notice.

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

Product: High-pressure cleaner

Type: 1.317-xxx

Currently applicable EU Directives

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/E230

2009/125/EC

Commission Regulation(s)

(EU) 2019/1781

Harmonised standards used

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997 + A1: 2001 + A2: 2008

EN 61000-3-2: 2014

EN 61000-3-11: 2000

EN IEC 63000: 2018

Applied conformity evaluation method

2000/14/EG: Annex V

Sound power level dB(A)

Measured: 88

Guaranteed: 91

The signatories act on behalf of and with the authority of the company management.

H. Jenner

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

Contents

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

Applicable regulation(s)

(EU) 2019/1781

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01/10/2022

Contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/CE

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01/10/2022

Index

2006/42/CE (+2009/127/CE)

2014/30/UE

2011/65/UE

2000/14/CE

2009/125/CE

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Winnenden, 01/10/2022

Contents

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

Contents

General remarks 47

Environmental protection 47

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

2000/14/EC: Annex V

Sound power level dB(A)

Measured: 88

Guaranteed: 91

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 2022/10/01

Contents

General information.... 52

Environmental protection.... 52

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

D-71364 Winnenden (Germany)

Tel: [phone]

Fax: [phone]

Winnenden, 01.10.2022

Contents

General instructions 57

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 1.10.2022

Contents

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

Contents

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU ³⁰

2000/14/EC

2009/125/EG

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Winnenden, 2022/10/01

Contents

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Winnenden, 2022/10/01

Table of contents

General instructions 83

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Winnenden, 2022/10/01

Table of contents

General instructions 88

Environmental protection 88

Intended use 88

Apparatus and spare parts.... 88

Scope of delivery....88

Description of the device 88

Safety devices 89

Symbols on the device....89

Assembly....89

Start-up 89

Operation....90

Transport 90

Storage 90

15 Device switch "0/OFF" / "I/ON"

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/ES

Applicable regulation(s)

(EU) 2019/1781

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Winnenden, 1. 10. 2022

Table of contents

2006/42/WE (+2009/127/WE)

2014/30/UE

2011/65/UE

2000/14/WE

2009/125/WE

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Relevant EU Directive

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

Regulation(s) used

(EU) 2019/1781

Harmonized standards applied

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997 + A1: 2001 + A2: 2008

EN 61000-3-2: 2014

EN 61000-3-11: 2000

EN IEC 63000: 2018

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

Contents

General notes.... 103

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/ES

2009/125/ES

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.10.2022

Contents

General notes.... 108

Environmental protection 108

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EZ

Applied regulations

(EU) 2019/1781

Applied harmonized standards

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997 + A1: 2001 + A2: 2008

EN 61000-3-2: 2014

EN 61000-3-11: 2000

EN IEC 63000: 2018

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Documentation representative:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.10.2022.

Contents

General notes.... 113

2006/42/EC (+2009/127/EC)

2014/30/EU

2011/65/EU

2000/14/EC

2009/125/EC

Applied provision(s)

(EU) 2019/1781

Applied harmonized standards

EN 60335-1

EN 60335-2-79

EN 62233: 2008

EN 55014-1: 2017 + A11: 2020

EN 55014-2: 1997 + A1: 2001 + A2: 2008

EN 61000-3-2: 2014

EN 61000-3-11: 2000

EN IEC 63000: 2018

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

Person authorized to compile the technical documentation:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 2022/10/01

Table of contents

General notes.... 118

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2022/10/01

Table of contents

General instructions 124

Environmental protection 124

Product: High-pressure washer

Type: 1.317-xxx

2006/42/EU (+2009/127/EU)

2014/30/EU

2011/65/EU

2000/14/EU

2009/125/EU

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel: [phone]

Winnenden, 2022/10/01

Table of Contents

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

H. Jenner Chairman of the Board of Management

S. Reiser Manager Regulatory Affairs & Certification

71364 Winnenden (Germany)

Phone: [phone]

Fax: [phone]

Chairman of the Board of Management

S. Reiser

Manager Regulatory Affairs & Certification

Winnenden, 2022/10/01

THANK YOU!

THANK YOU! DANKE! GRACIAS!

Register your product and benefit from many advantages.

www.kaercher.com/welcome

Rate your product and tell us your opinion.

www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28-40

71364 Winnenden (Germany)