SBS-TW-3000/100G - Scale STEINBERG - Free user manual and instructions

Product Type	Digital Pocket Scale
Brand	Steinberg
Model	SBS-TW-3000/100G
Maximum Capacity	3000 g
Accuracy	0.1 g
Minimum Weight	0.6 g
Units of Measurement	g, oz, lb, kg, tl, ct
Display	LCD
Power Supply	2 AAA batteries (1.5 V)
Battery Life	26 hours
Main Functions	Zero setting, tare, piece counting, calibration
Calibration	Manual with calibration weights (2000 g and 3000 g)
Counting Function	Samples of 25, 50, 75 or 100 pieces
Tare Range	Up to maximum capacity
Auto-zero	Yes, via M button
Overload Protection	Do not exceed 3000 g
Usage Recommendations	Stable surface, away from vibrations and drafts
Maintenance	Clean with a soft dry cloth, avoid moisture
Storage	In a dry, ventilated place, away from corrosive gases
Safety	Do not open, do not use in rain or storm
Repairability	Contact the retailer, do not repair yourself

Frequently Asked Questions - SBS-TW-3000/100G STEINBERG

How to calibrate my Steinberg SBS-TW-3000/100G scale?

Turn on the scale, press the M button until 3000 is displayed, release then press again to show CAL and the first weight (2000g). Place the 2000g weight, wait for stability, then place the second 3000g weight. The screen displays PASS and the scale turns off.

What to do if my scale does not show zero when empty?

Press the M button to perform auto zero.

How to use the tare function?

Place an empty container on the scale, wait for a stable value, then press the T button (or M depending on model) to tare. The display shows 0, and you can weigh the net content.

What batteries to use?

Use 2 AAA 1.5V batteries. Replace exhausted batteries with new ones.

Can I weigh more than 3000 g?

No, the maximum capacity is 3000 g. Do not overload the scale to avoid damaging the load cells.

How to clean my scale?

Clean it with a soft dry cloth. Avoid direct contact with water and never immerse the scale in water.

What to do if the scale displays an error message?

Consult the manual for error codes. Generally, remove the batteries, wait a few minutes, then reinsert them. If the problem persists, contact the retailer.

How to use the counting function?

Place a sample of 25, 50, 75 or 100 pieces on the platform. Press the PCS button for 2 seconds, select the number with the M button, confirm with PCS. The scale then displays the number of pieces.

Where to find the serial number?

The serial number is on the device's nameplate.

Can the scale be used outdoors?

It is not recommended to use the scale in rain or stormy weather. Use it in a dry environment protected from the weather.

USER MANUAL SBS-TW-3000/100G STEINBERG

Abstract geometric line pattern with overlapping angular shapes on a gray background (no text or symbols)

INTRODUCTION

Before you use the scale, please read this manual carefully, and keep it stored properly for future use.

SAFETY GUIDE

For good performance and precise measurement, be careful during daily operation and maintenance. Regard the following instructions:

• Do NOT overload the scale. This will damage the load cell and void the warranty.
• Do NOT leave load on the scale for long. This will decrease the scale's accuracy and shorten the load cell's life.
• When the scale runs out of power, replace the batteries.
• Do NOT use the scale in thunder or rain.
• Do NOT attempt to repair the scale yourself. Contact your local representative.
• Avoid extreme temperatures. Do not place the unit in direct sunlight or near the air conditioning.
• Make sure the scale is placed on a stable table and is not subject to vibrations.
• Do not use the scale close to large electrical appliances such as welding machines or large motors. Do not leave batteries in the device if you do not use it for a long time.
• Avoid vibrations. Do not place your scale near vibrating heavy machinery.
• Avoid places where moisture can lead to condensation. Avoid direct contact with water.
  • Do not place the unit close to windows, doors or fans that may cause unstable results due to air currents.
• Keep your machine clean. Do not store products on the scale when it is not used.

SPECIFICATIONS

Model SBS-TW-3000/100G SBS-TW-500/10G
Max weight / Accuracy 3000 g / 0.1 g	500 g / 0.01 g
Min. weight 0.6 g 0.06 g
Display LCD
Units g / oz / lb / kg / tl / ct
Power 2 x AAA batteries
Functions Zero, tare, pieces counting, calibration
Max operation time with batteries	26 hours

DISPLAY

pee 100.0.0 g oz lt k t ct 2 4 5 T/0

1. main display
2. units – during normal operation the display will show one unit
3. counting function
4. negative load indication
5. tare

FUNCTIONS OF THE KEYS

„ON / OFF“:

Press the ON / OFF button to start the scale.

„M” button:

The unit change is possible by pressing the "M" button. Then press up to reach the desired unit. The following units can be selected: g / oz / lb / kg / tl / ct.

Counting function „PCS“: Put the desired number of pieces on the scale dish (it must be 25, 50, 75 or 100). Press and hold the PCS button for about 2 seconds, the display will show “100”. Then press the “M” button to select the number corresponding to the number of pieces on the scale dish - 25, 50, 75 or 100. Press PCS to confirm the selection. The scale will show the number of pieces put on the scale dish. To exit the piece calculation mode, press the “M” button.

Tare key „T”: Press this button to subtract the weight of a container or any weight on the scale. This key is also used for zeroing the scale.

FUNCTION OF TARE

1. Place an empty container on the weighing platform until the balance indicates a stable value. Then press „M“. Your balance now displays „0“. To exit the tare function, remove the container and repress the „ZERO“ button. Your scale is back to normal.

2. The range of tare: entire load range.

AUTO-ZERO

Press „M“ if the scale does not show „0“ when nothing is placed on it. The scale must not be overloaded.

CALIBRATION

Switch the scale on. Press and hold the "M" button until the display shows 500 (in case of the SBS-TW-500/10G) / 3000 (in case of the SBS-TW-3000/100G). Release the "M" button, then press it again - the display will show "CAL" and a flashing standard load value in grams: 200 (in case of the SBS-TW-500/10G) / 2000 (in case of the SBS-TW-3000/100G). Put the indicated standard load value on the scale dish and wait for the scale to stabilise. Then the display will show another flashing standard load value in grams (500 in case of the SBS-TW-500/10G / 3000 in case of the SBS-TW-3000/100G) which must be placed on the scale dish for the scale to stabilise. When the calibration is completed, a flashing "PASS" message is displayed on the display and the scale turns off.

TRANSPORTATION AND STORAGE

Shaking, crashing and turning upside down of the device should be prevented when transported. Store it in a properly ventilated surrounding with dry air and without any corrosive gas.

REGULAR CONTROL OF THE DEVICE

Regularly control that the device doesn't present any damage. If there is any damage, please stop using the device. Please contact your customer service to solve the problem.

What to do in case of a problem?

Please contact your customer service and prepare following information:

• Invoice number and serial number (the latter is to be found on the technical plate on the device).

- If relevant, a picture of the damaged, broken or defective part.

• The more detailed your information, the better the customer service will be able to solve your problem rapidly and efficiently!

CAUTION: Never open the device without the authorization of your customer service. This can lead to a loss of warranty!

MODE D'EMPLOI

BALANCE DE TABLE

FR

INTRODUCTION

Abstract geometric line pattern with overlapping angular shapes on a gray background (no text or symbols)

INTRODUZIONE

Rev. 12.04.2022 Rev. 12.04

NOTIZEN | NOTES NOTIZEN | NOTES

steinberg® BASIC

For the disposal of the device please consider and act according to the national and local rules and regulations.

CONTACT

expondo Polska sp. z o.o. sp. k.