303673 - Receiver Aplic - Free user manual and instructions

Product Type	Bluetooth Audio Receiver
Brand	Aplic
Model	303673
Bluetooth Version	5.0 + EDR, supports A2DP
Range	Up to 10 m (Class 2)
Battery	3.7 V, 35 mAh
Power Supply	Micro USB 5 V DC, 500 mA
Microphone	Built-in
Connectivity	3.5 mm jack (via included adapter)
Package Contents	Receiver, jack adapter, microUSB cable, user manual
Approximate Weight	15 g
Approximate Dimensions	46 x 46 x 16 mm
Status LED	Red (charging), Blue (connected), Red/Blue flashing (pairing)
Hands-free Calling Function	Yes
Care	Clean with a soft dry cloth. Avoid moisture.
Safety	Do not open, do not expose to water or high temperatures.
Compliance	Directive 2014/53/EU, WEEE 2012/19/EU

Frequently Asked Questions - 303673 Aplic

How to pair the receiver with my smartphone?

Turn on the receiver by pressing and holding the multifunction button for 2-3 seconds. The LED blinks. Enable Bluetooth on your smartphone, search for devices, and select 'aplic-303673'. The connection is established when the blue LED stays on.

How to charge the receiver?

Use the included microUSB cable and plug it into a 5V power source (USB port or wall adapter). The red LED lights up during charging and turns off when fully charged. Unplug after charging.

What is the battery life?

The 35 mAh battery provides about 2-3 hours of continuous use, depending on volume and distance.

What to do if the Bluetooth connection is unstable?

Make sure the distance does not exceed 10 meters and that no obstacles (walls, furniture) interfere with the signal. Reduce distance or re-pair the devices. If the problem persists, turn off the receiver for 20 seconds and try again.

Can I use the receiver for phone calls?

Yes, the receiver has a built-in microphone. During an incoming call, briefly press the multifunction button to answer, and again to hang up.

How to turn off the receiver?

Press and hold the multifunction button for 2-3 seconds. The LED stops blinking. If disconnected from the audio device, it automatically turns off after one minute.

What to do if the receiver does not turn on?

Fully recharge the battery using the microUSB cable. If the problem persists, check that the cable and power source work. After charging, press and hold the button for 2-3 seconds to turn on.

What is the maximum range of the receiver?

The range is 10 meters in open space (Class 2). Obstacles like walls reduce the range.

Can I connect the receiver to a Hi-Fi system?

Yes, use the included jack adapter to connect the receiver to the audio input of your Hi-Fi system. Plug the adapter into the receiver's jack and connect it to the audio device.

How do I know if the battery is charged?

During charging, the red LED stays on continuously. When charging is complete, the red LED turns off. If the receiver is on and connected, the blue LED stays on.

USER MANUAL 303673 Aplic

Blue abstract logo shape resembling a stylized letter 'Q' or partial circle (no text or symbols)

aplic

Bluetooth Audio Receiver

ENG: Latest information, drivers, user manuals and data sheets can be found at www.ganzeinfach.de in our download area.

Thank you for choosing an aplic product. Please read the following user manual carefully so as to get the most from the product you have purchased. Before using the product, first check that the delivered item is complete, accurate and undamaged.

1. Scope of delivery

• Bluetooth audio receiver
  • Audio connection adapter
• MicroUSB charging cable
• User manual

2. Technical data

Connection Bluetooth V5.0	+ EDR / supports A2DP
Range Class 2 (up to 10m)
Battery 3.7V, 35mAh
Max. transmission power -4.38 dBm
Frequency range 2402-2480 Ghz
Charging Port microUSB (5V DC, 500mA)
Features Built-in microphone

3. Initial use

1. Take the device out of the package and remove all the packaging material. Charge the Bluetooth audio receiver fully before using it for the first time.
2. Connect the device using the supplied micro-USB charging cable to a suitable charging source such as the USB port of a computer or a USB power adapter (for example, the charger of a smartphone). The LED display is illuminated in red during the charging process. When the charging is completed, it turns off.

3. Please unplug the device from the power source after charging each time, in order to avoid constant recharging.

4. Then connect the audio receiver using the supplied audio adapter to an audio output device. This may be, for example, a hi-fi system.

5. To turn the device on or off, press and hold the multifunction button on the front panel for about 2-3 seconds. The LED in the button starts flashing.
6. If you disconnect the device from your audio playback device, the Bluetooth receiver turns off automatically after about one minute.

Note: Charge the battery fully once again, if the receiver switches off in battery mode or if it cannot be switched on.

4. Establishing a Bluetooth connection

1. Turn on the Bluetooth audio receiver by pressing and holding the multifunction key for about 2-3 seconds. The button is located on the front of the device.
2. The LED indicator on top starts flashing. The Bluetooth audio receiver then waits for a connection.
3. Enable the Bluetooth interface on your audio playback device (e.g., a Smartphone) and perform a scan. Then pair the device using "aplic-303673". The connection has now been established successfully with the Bluetooth audio receiver.

Note: Switch off the audio receiver for about 20 seconds and try to pair again if the connection could not be established.

5. Bluetooth calls

You can answer incoming calls by pressing the multifunction button briefly during an incoming call. You can hang up by pressing the multifunction button briefly during a call.

1. Status LED

Function Status LED
Pairing or establishing a connection	The blue and red LEDs flash successively
Connected The blue LED starts glowing
Standby mode LED turns off	after flashing for one minute
Charging process	The red LED glows continuously Once the device is fully charged, the LED stops glowing
Charging process and connected	The red and blue LEDs glow continuously. If the device is fully charged, the red LED stops glowing

7. Troubleshooting

The following problems can result in disconnection or unsuccessful connection:

Error Troubleshooting
The transmission has exceeded the range of 10m, or there are barriers such as walls or furniture between the receiver and the transmitter.	Ensure that the range is not exceeded.
One of the two devices (audio output device or Bluetooth receiver) is turned off.	Turn on the corresponding devices.
The pairing did not work properly and switched off automatically after 5 minutes.	Pair the devices again. Make sure that the connection is not prevented by excessive transmission range or obstacles.

8. Safety instructions and disclaimer

Never try to open the device to carry out repairs or modifications. Avoid contact with the mains voltage. Do not short-circuit the product. The device is not approved for outdoor use. Therefore please use it only in dry surroundings. Protect it from high humidity, water and snow. Keep the device away from high temperatures. Do not expose the device to sudden changes in temperature or strong vibrations, as this could damage the electronic components. Check the device for damage before using it. The device should not be used if it was subject to impact or has been damaged in some other manner.

Please comply with the local regulations and restrictions. Do not use the device for purposes other than those described in the user manual. This product is not a toy. Keep it out of the reach of children or mentally disabled persons. Any repair or modifications to the device, which is not carried out by the original supplier will void any warranty and guarantee claims. The device should only be used by those who have read and understood this user manual. The specifications of the device may be changed without prior intimation.

9. Disposal instructions

In line with the European WEEE directive, electrical and electronic devices should not be disposed of along with domestic waste.

Their components have to be separately sent for recycling or disposal, because improper disposal of toxic and dangerous components may permanently damage the environment. According to the Electrical and Electronic Equipment Act (ElektroG), you are obliged (as a consumer) to return (free of charge) all electrical and electronic devices to the manufacturer, the point of sale, or public collection points at the end of their service life. The relevant local laws regulate the details in this regard. The symbol displayed on the product, in the user manual or/and on the packaging refers to these regulations. With this manner of sorting, recycling and disposal of used devices, you make an important contribution towards protecting our environment.

10. Instructions for battery disposal

In conjunction with the sale of batteries along with the supply of devices that include batteries, the supplier is obliged to point out the following to the customer: The customer is legally obliged to return used batteries. He can return used batteries which the supplier offers or has offered as new batteries in his assortment free of charge to the supplier's dispatch warehouse (shipping address). The symbols shown on the batteries indicate the following: Pb = battery contains more than 0.004 percent lead by weight, Cd = battery contains more than 0.002 percent cadmium by weight, Hg = battery contains more than 0.0005 percent mercury by weight.

The symbol of the crossed-out dustbin means that the battery may not be disposed of in household waste.

WEEE Guideline: 2012/19/EU

WEEE Register no.: DE 67896761

The company WD Plus GmbH hereby certifies that the device 303673/20190325SZ229 complies with the fundamental requirements and all other relevant stipulations of the guideline 2014/53/EC. A complete conformity statement can be obtained from: WD Plus GmbH, Wohlenbergstraße 16, 30179 Hannover, https://downloads.ganzeinfach.de/