USER MANUAL DIS-700G-28XS D-LINK
natural_image
Line drawing of a multi-USB network switch device (no text or labels)
CLI Reference Guide
Product Model : DIS-700G-28XS
Industrial 10G Ethernet Managed Switch
Release 1.00
CONTENTS
1 SCOPE 10
1.1 SCOPE 10
2 OPERATOR INTERFACE 12
2.1 INTRODUCTION 12
3 COMMANDS DESCRIPTIONS....16
3.1 INITIALIZE MODE COMMANDS 16
3.1.1 bye 16
3.2 ENABLE MODE COMMANDS....18
3.2.1 bye 18
3.2.24 show runningcfg backup.... 20
3.2.25 show bootloader.... 20
3.2.26 show system information 20
3.2.27 show http 20
3.2.28 show temperature 21
3.2.29 show time.... 21
3.2.30 show version.... 21
3.2.31 show system inventory 21
3.2.32 show aging 21
3.2.33 showfdb 21
3.2.34 showfdb interface gigabit 22
3.2.35 showfdb vlan 22
3.2.36 showfdbstatic 22
3.2.37 showfdbstatic interface gigabit 22
3.2.38 showfdbstatic vlan 22
3.2.39 show interface gigabit 22
3.2.40 show interface gigabit counter 23
3.2.41 show interface gigabit stp 23
3.2.42 show interface gigabit vlan 23
3.2.43 show jumboframe 23
3.2.44 show stp.... 23
3.2.45 show vlan 23
3.2.46 show vlan 23
3.2.47 show cos-queue-mapping 24
3.2.48 show interface gigabit qos 24
3.2.49 show policer 24
3.2.50 show profile acl {|all} 24
3.2.51 show interface gigabit acl.... 24
3.2.52 show queue-scheduler profile.... 24
3.2.53 show queue-shaper 24
3.2.54 show port-shaper 24
3.2.55 show port-isolation 25
3.2.56 show interface gigabit port-isolation.... 25
3.2.57 show interface gigabit storm-control 25
3.2.58 show vlan {unknown-uc|unknown-mc|broadcast} 25
3.2.59 show port-mirror 25
3.2.60 show interface gigabit rmon-counter 25
3.2.61 show interface vlan igmp.... 26
3.2.62 show multicast-fdb.... 26
3.2.63 show multicast-fdb static 26
3.2.64 show ring 26
3.2.65 show ssl decrypted.... 26
3.2.66 show ssl encrypted.... 26
3.2.67 show interface gigabit 26
3.2.68 show ext-tpid 27
3.2.69 show interface vlan.... 27
3.2.70 show interface vlan 27
3.2.71 show protocol-vlan 27
3.2.72 show interface gigabit vlan 27
3.2.73 show vlan-trans 27
3.2.74 show igmp-mvr-profile {|all} 28
3.2.75 show igmp-acl-profile {|all}. 28
3.2.76 show interface gigabit igmp 28
3.2.77 show interface vlan igmp.... 28
3.2.78 show interface vlan igmp 28
3.2.79 show multicast-fdb srclist 28
3.2.80 show multicast-fdb 28
3.2.81 show dot1x 29
3.2.82 show dot1x pae-info-status {|all}. 29
3.2.83 show dot1x eapol-stats {|all} 29
3.2.84 show dot1x radius-stats.... 29
3.2.85 show http 29 ...... 29 30 30 30
3.3.1 bye 31 31 31 31 32 32 32 33 34 34 { cli|console|web} 34 34 35 35 35 35 {binary|cli} 37 {binary|cli} 38 38 39 39 40 41 netmask gateway 41 netmask 41 41 ...... 42 42 42
3.3.51 system-info name 42
3.3.52 http port { | default} 43
3.3.53 temperature shift down 43
3.3.54 temperature shift up 43
3.3.55 temperature threshold down ...... 43
3.3.56 temperature threshold up 43
3.3.57 vlan 43
3.3.58 vlan { | broadcast | disable | unknown-mc | unknown-uc} {block | forward}...... 44
3.3.59 vlan disable 44
3.3.60 aging 44
3.3.61fdb-delete all 44
3.3.62fdb-delete interface gigabit 44
3.3.63fdb-delete vlan 45
3.3.64 fdbstatic interface gigabit 45
3.3.65 fdbstatic delete 46
3.3.66 fdbstatic delete all 46
3.3.67 fdbstatic delete interface gigabit 46
3.3.68 fdbstatic delete vlan 46
3.3.69 stp {disable|enable}....46
3.3.70 stp bpdu {deny|flooding} 46
3.3.71 stp forward-delay 46
3.3.72 stp hello-time 47
3.3.73 stp max-age 47
3.3.74 stp msti { add | create | delete | set} { | range}. 47
3.3.75 stp priority 47
3.3.76 stp region-name 47
3.3.77 stp revision 47
3.3.78 stp version {stp|rstp|mstp}....48
3.3.79 jumboframe {enable|disable} 48
3.3.80 jumboframe mtu 48
3.3.81 cos-queue-mapping cos queue 49
3.3.82 policer cos-mark green yellow red 49
3.3.83 policer dscp-mark green yellow red .... 49
3.3.84 policer ingress-color {aware|blind} 49
3.3.85 policer ingress-color cos {red|yellow|green} 50
3.3.86 mirror analyzer-port {enable|disable} 50
3.3.87 mirror analyzer-port 50
3.3.88 vlan unknown-uc {blcok|forward}....50
3.3.89 vlan unknown-mc {block|forward}....50
3.3.90 vlan broadcast {block|forward} 50
3.3.91 port-mirror monitor-port 51
3.3.92 port-mirror {enable|disable}....51
3.3.93 port-mirror {tx-analyzer-port|rx-analyzer-port} ....51
3.3.94 counter interface-counter clear 51
3.3.95 counter rmon-counter clear 51
3.3.96 multicast-fdb delete all 51
3.3.97 multicast-fdb static delete....52
3.3.98 multicast-fdb static interface gigabit ....52
3.3.99 ring-group 52
3.3.100 ext-tpid 52
3.3.101 profile igmp-mvr 53
3.3.102 profile igmp-acl 53
3.3.103 dot1x {enable|disable}. 53
3.3.104 dot1x radius set 54
3.3.105 dot1x clear eapol-stats {|all} 54
3.3.106 dot1x clear dot1x-radius-stats.... 54
3.3.107 https {enable|disable}....54
3.3.108 https port {|default} 54
3.3.109 interface trunk-group 55
3.3.110fdb-delete interface trunk-group 55
3.3.111 ssl default-certificate 55
3.3.112 ssl upload 55
3.4 INTERFACE GIGABIT MODE COMMANDS....56
3.4.1 accfrm 56
3.4.2 priority 56
3.4.3 vlan 56
3.4.4 vlan disable 56
3.4.5 vlan tag 56
3.4.6 vlan untag 56
3.4.7 stpport {disable|enable} 57
3.4.8 stpport cost ......57
3.4.9 stpport edge-port {enable|disable}....57
3.4.10 stpport priority 57
3.4.11 flow-control {enable|disable}....58
3.4.12 speed....58
3.4.13 sfp-speed (for 10G ports) 58
3.4.14 sfp-speed (for 1G ports) 58
3.4.15 port {enable/disable}.... 58
3.4.16 default vlan....59
3.4.17 policer pir pbs cir cbs {drop|cos|dscp} 60
3.4.18 policer disable....60
3.4.19 acl-profile-bind 60
3.4.20 def-acl {permit|deny} 60
3.4.21 queue-scheduler bind 60
3.4.22 port-shaper {enable|disable}....60
3.4.23 port-shaper 61
3.4.24 queue-shaper {enable|disable}....61
3.4.25 queue-shaper queue 61
3.4.28 unknown-uc {block|forward}....61
3.4.29 unknown-mc rate 62
3.4.30 unknown-mc {block|forward}....62
3.4.31 broadcast rate 62
3.4.32 broadcast {block|forward} 62
3.4.33 vlan-stack {enable|disable} 62
3.4.34 protocol-vlan create 62
3.4.35 protocol-vlan delete 63
3.4.36 vlan-trans create many-to-....63
3.4.37 vlan-trans delete 63
3.4.38 igmp mvrprofile 64
3.4.39 igmp aclprofile 64
3.4.40 igmp max-channel ....64
3.4.41 dot1x {force-reinitialize|force-reauthenticate}....64
3.4.42 dot1x auth-port-control {auto|force-authorized|force-unauthorized} 64
3.4.43 dot1x auth-quiet-period 64
3.4.44 dot1x auth-tx-period 65
3.5.4 acl-profile set entry mac-type set vlan 67
3.5.5 acl-profile set entry mac-type set vlan any....68
3.5.6 acl-profile set entry mac-type set {srcmac|dstmac} . 68
3.5.7 acl-profile set entry mac-type set ethertype ...... 68
3.5.8 acl-profile set entry mac-type set ethertype any....69
3.5.9 acl-profile set entry ipv4-type set {srcip|dstip} .... 69
3.5.10 acl-profile set entry ipv4-type set ip-protocol ...... 69
3.5.11 acl-profile set entry ipv4-type set ip-protocol any....70
3.5.12 acl-profile set entry l4port-type set protocol {tcp|udp}....70
3.5.13 acl-profile set entry l4port-type set {srcip|dstip} . 70
3.5.14 acl-profile set entry l4port-type set {srcport|dstport} ...... 71
3.5.15 acl-profile set entry l4port-type set {srcport|dstport} any.....71
3.5.16 acl-profile set entry tos-type set {srcip|dstip} ..... 71
3.5.17 acl-profile set entry tos-type set type {precedence|tos|dscp} 72
3.5.18 acl-profile set entry tos-type set type any 72
3.5.19 acl-profile set entry action forwarding {deny|permit}....72
3.5.20 acl-profile set entry action queue 73
3.5.21 acl-profile set entry action cos ....73
3.5.22 acl-profile set entry action copyframe.... 73
3.6 SCH-PROFILE CONFIGURE MODE COMMANDS....74
3.6.1 scheduler-profile method {spq|spq-wrr|wrr} 74
3.6.2 scheduler-profile queue weight 74
3.7 SNMP CONFIGURE MODE COMMANDS 75
3.7.1 snmp notify 75
3.7.2 snmp notify delete.... 75
3.7.3 snmp target .... 75
3.7.4 snmp target delete.... 75
3.7.5 snmp community group 76
3.7.6 snmp community ro....76
3.7.7 snmp community rw....76
3.7.8 snmp community view 76
3.7.9 snmp create-community {ro | rw} {view | group} 77
3.7.10 snmp create-group model {v1 | v2 | v3sum} level {auth | noauth | priv} read write 77
3.7.11 snmp create-user {access | group} {ro | rw} {md5 | sha} des ..... 77
3.7.12 snmp create-view type { exclude | include} subtree ....78
3.7.13 snmp delete-community 78
3.7.14 snmp delete-group 78
3.7.15 snmp delete-user name 79
3.7.16 snmp delete-view { index | name }.... 79
3.7.17 snmp version { v2c | v3 }.... 79
3.8 INTERFACE VLAN MODE COMMANDS.... 80
3.8.1 igmp vlan {create|delete} 80
3.8.2 igmp router-port 80
3.8.3 igmp access-mode {snooping|proxy}....80
3.8.4 igmp leave-mode {normal|fast}....80
3.8.5 igmp version {v2|v3|v3compatible}....80
3.8.6 igmp robustness 80
3.8.7 igmp query-interval ...... 80
3.8.8 igmp max-response-time 81
3.8.9 igmp last-member-query-count 81
3.8.10 igmp last-member-query-interval 81
3.8.11 igmp vlan interface address ...... 81
3.8.12 ip-address 81
3.8.13 ip-address netmask 81
3.8.14 igmp version {v2|v3| v3compatible} 82
3.9 RING GROUP MODE COMMANDS....83
3.9.1 ringv2-group 83
3.9.2 guardtimer 83
3.9.3 mode enable 83
3.9.4 mode disable....83
3.9.5 node1 83
3.9.6 node2 83
3.9.7 role ring-master 83
3.9.8 role ring-slave 84
3.9.9 role coupling-primary 84
3.9.10 role coupling-backup 84
3.10 IGMP MVR MODE COMMANDS 86
3.10.1 igmp-mvr {create|delete}....86 entry 86 entry delete 86
3.11 IGMP ACL MODE COMMANDS 87
3.11.1 igmp-acl {create|delete}. 87 {default-deny| default-permit} 87 entry {|all} {permit|....87 entry delete....87
3.12 TRUNK GROUP MODE COMMANDS 88
3.12.1 trunk enable static 88 88 |all}. 88
3.13 ALARM RELATED COMMANDS....89
3.13.1 show profile alarm....89 {mask|unmask|major|minor}....90
[LIST OF TABLES]
Table 2-1 List of Execution Modes ...... 13
Table 2-2 List of Terminal Keys....14
Figure 2-1 Screen Description....13
1. Scope
1.1 Scope
1 Scope
1.1 Scope
This user guide describes the commands and parameters of the Command Line Interface (CLI) as implemented in the current version of DIS-700G-28XS software. These commands are used to set-up, administer and maintain the system.
1.2 Audience
The guide is intended for Operating personnel (sometimes called craft persons).
1.3 Pre-required Knowledge
The reader must be familiar with the:
Basic operations of DIS-700G-28XS switch (see the Quick Installation Guide).
1.4 Access to Hardware Interface
Access to the hardware interface is by a terminal (or computer with terminal emulation software). Requirements for the terminal are:
• RS-232 ASCII port
You may want to refer to the following related documents:
• DIS-700G-28XS Quick Installation Guide
2. Operator Interface
2.1 Introduction
2 Operator Interface
2.1 Introduction
Access to the Operations System (OS) /Network Element (NE) system is protected by a logon security system. You can log on to the NE with the user name and password. After three failed logon attempts, the system refuses further attempts.
After you log on, the system monitors the interface for periods of inactivity. If the interface is inactive for too long, you are automatically logged off.
All the NEs have the same initial user name (admin) and password (admin). You should change the password as soon as possible, because the initial password is known to anyone who reads this manual. You can also change the user name or add additional user names. Use the “account add” command to enter a new user identification, password and authorization level. The system can handle one local logon session and at least four remote/OS sessions.
2.2 Connect Interface
Interface Parameter Console Baud rate: 115200bps,Data bit: 8,Parity: None,Stop bit: 1 Telnet Port 23 SSH Port 22 (In Windows, you can run terminal emulator such as PuTTY)
2.3 Authorization Level
Level Description Superuser Superuser can access all management features. Engineer Engineer can access all management features except user account management. Guest (default) Read-only mode (Guest can only change his own password). Users of this level can query pages like PM and FM.
2.4 Login Example
Localhost login: admin
Password: *****
DIS-700G-28XS 1.00.001
Localhost:>enable
Localhost:%show version
DIS-700G-28XS v1.00.001
Figure 2-1 login example
2.5 Execution Modes
The CLI contains several execution modes. Users will see different set of commands under different execution modes. Table 2-1 lists all the execution modes and their purposes. When users enter a certain execution mode, the corresponding mode prompt will be displayed automatically on the screen. The mode prompts of all the execution modes are also listed in Table 2-1.
Table 2-1 List of Execution Modes
Mode Access Level Prompt Init Mode Guest > Enable Mode Guest % Config Mode Guest (conf)# Alarm Profile Config Mode Engineer (alarm-profile-conf)# Gigabit Interface Config Mode Engineer (gigabit-intf-conf)# ACL Profile Config Mode Engineer (acl-profile-conf)# scheduler Profile Config Mode Engineer (sch-profile-conf)# Vlan Interface Config Mode Engineer (vlan-intf-conf)# IGMP MVR Profile Config Mode Engineer (igmp-mvr-profile-conf)# IGMP ACL Profile Config Mode Engineer (igmp-acl-profile-conf)# Ring Group Config Mode Engineer (ring-group-conf)# Trunk Group Config Mode Engineer (trunk-group-conf)# Router Rip Config Mode Engineer (router-rip-conf)# Router Ospf Config Mode Engineer (router-ospf-conf)#
2.6 Getting help
The user can get help by entering a question mark '?' at each position in the command. The displayed result depends on the execution mode and previous input.
2.7 Terminal Key Function
Following is the list of all the terminal keys and their function.
Table 2-2 List of Terminal Keys
ENTER Run a CLI config script CTRL-M TAB Tab completion. If tab is pressed after a non-whitespace character, complete the word before the Tab.If tab is pressed after a whitespace character, complete the next word. CTRL-I ? Display available commandsIf ? is pressed after a non-whitespace character, show possible choices for this word.If ? is pressed after a whitespace character, show possible choices for the next word. Up history CTRL-P Down history CTRL-N Home Move the cursor to the beginning of the input line CTRL-A End Move the cursor to the end of the input line CTRL-E Move the cursor backward CTRL-B Move the cursor forward CTRL-F BACKSPACE Erase the character before the cursor CTRL-H
2.8 Notation Conventions
The notation conventions for the parameter syntax of each CLI command are as follows:
Parameters enclosed in [ ] are optional.
Parameter values are separated by a vertical bar “|” only when one of the specified values can be used.
Parameter values are enclosed in {} when you must use one of the values specified.
3. Commands Descriptions
3.1 Initialize Mode Commands
3 Commands Descriptions
3.1 Initialize Mode Commands
The commands in this section (except 'enable' command) can be executed under all command modes. These commands are global commands.
3.1.1 bye
Description Quit CLI. Syntax bye Parameter None
3.1.2 !
Description Execute the specific number of command in history Syntax ! Parameter Name Description Valid values: 1 ~ 32Type: Mandatory
Description Enter configuration mode. Syntax configure Parameter None
3.1.4 enable
Description Enter enable mode. Syntax enable Parameter None
3.1.5 exit
Description Exit current mode. Syntax exit Parameter None
3.1.6 list command-tree
Description List tree of all available CLI commands Syntax list command-tree Parameter None
3.1.7 list timezone
Description List time zones Syntax list timezone Parameter None
3.1.8 show env
Description Show CLI environment variables Syntax show env Parameter None
3.1.9 show history
Description Show command history (Note: commands issued in one execution mode only appear in history of that execution mode) Syntax show history Parameter None
3.1.10 show time
Description Show current time Syntax show time Parameter None
3.1.11 show uptime
Description Show uptime Syntax show uptime Parameter None
3.1.12 sleep
Description Sleep for the specified number of milli-seconds Syntax sleep Parameter Name Description Valid values: 1 ~ 0xFFFFFFFF msType: Mandatory
3.2 Enable Mode Commands
All the "show --" commands in this section can also be executed under any other command mode except Initialize Mode.
3.2.1 bye
Description Quit CLI. Syntax bye Parameter None
3.2.2 !
Description Execute the specific number of command in history Syntax ! Parameter Name Description Valid values: 1 ~ 32Type: Mandatory
3.2.3 exit
Description Exit current mode. Syntax exit Parameter None
Description Enter configuration mode. Syntax configure Parameter None
3.2.5 disable
Description Enter init mode. Syntax disable Parameter None
3.2.6 kick
Description Kick off a logged-in user (only superuser can execute this command) Syntax kick{console | cli | web} Parameter Name Description Valid values: 1 ~ 10Type: Mandatory
3.2.7 list alarm
Description List valid alarm ID Syntax list alarm Parameter None
3.2.8 list command-tree
Description List tree of all available CLI commands Syntax list command-tree Parameter None
3.2.9 list event
Description List valid event ID Syntax list event Parameter None
3.2.10 list execution-modes
Description List all available execution modes Syntax list execution-modes Parameter None
3.2.11 list timezone
Description List timezones Syntax list timezone Parameter None
3.2.12 ping
Description send ICMP ECHO_REQUEST to network hosts Syntax ping <ip> ping <ip> count <count> ping <ip> count <count> size <size> ping <ip> size <size> Parameter Name Description Valid values: -Type: Mandatory Packet countValid values: 1 ~ 4294967295Default value: 0Type: Mandatory The number of data bytes to be sentValid values: 1 ~ 65500Default value: 0Type: Mandatory
3.2.13 show sntp
Description Show SNTP information. Syntax show sntp Parameter None
3.2.14 show account
Description Show account list. Syntax show account Parameter None
3.2.15 show login-users
Description Show logged-in users. Syntax show login-users Parameter None
3.2.16 show syslog
Description Show syslog configuration. Syntax show syslog Parameter None
3.2.17 show clisettings
Description Show CLI settings. Syntax show clisettings Parameter None
3.2.18 show runningcfg
Description Show running configuration. Syntax show runningcfg Parameter None
3.2.19 show runningcfg default
Description Show default running configuration. Syntax show runningcfg default Parameter None
3.2.20 show firmware status
Description Show firmware update status. Syntax show firmware status Parameter None
3.2.21 show firmware partition
Description Show firmware partition information. Syntax show firmware partition Parameter None
3.2.22 show management
Description Show management channel settings. Syntax show management Parameter None
3.2.23 show route static
Description Show routing static table. Syntax show route static Parameter None
3.2.24 show runningcfg backup
Description Show running configuration backup. Syntax show runningcfg backup Parameter None
3.2.25 show bootloader
Description Show boot loader information. Syntax show bootloader Parameter None
Description Show system information. Syntax show system information Parameter None
3.2.27 show http
Description Show HTTP configuration. Syntax show http Parameter None
3.2.28 show temperature
Description Show temperature information. Syntax show temperature Parameter None
3.2.29 show time
Description Show current time. Syntax Show time Parameter None
3.2.30 show version
Description Show version information. Syntax show version Parameter None
3.2.31 show system inventory
Description Show system inventory. Syntax show system inventory Parameter None
3.2.32 show aging
Description Show aging time for MAC learning table (system-wide). Syntax show aging Parameter None
3.2.33 showfdb
Description Show MAC learning table. Syntax show fdb Parameter None
3.2.34 showfdb interface gigabit
Description Show MAC learning table per gigabit port. Syntax show fdb interface gigabit Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.2.35 showfdb vlan
Description Show MAC learning table per VLAN index. Syntax Show fdb vlan Parameter Name Description Valid values: 1~4094Type: Mandatory
3.2.36 show fdbstatic
Description Show static MAC forwarding table. Syntax Show fdbstatic Parameter None
3.2.37 show fdbstatic interface gigabit
Description Show static MAC forwarding table per gigabit port. Syntax Show fdbstatic interface gigabit Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.2.38 show fdbstatic vlan
Description Show static MAC forwarding table per VLAN index. Syntax show fdbstatic vlan Parameter Name Description Valid values: 1~4094Type: Mandatory
3.2.39 show interface gigabit
Description Show interface information per gigabit port. Syntax show interface gigabit Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.2.40 show interface gigabit counter
Description Show Ethernet counter per gigabit port. Syntax show interface gigabitcounter Parameter Name Description Valid values: 1 ~ 28Type: Mandatory counter Show Gigabit Ethernet counter.
3.2.41 show interface gigabit stp
Description Show STP information per gigabit port. Syntax show interface gigabitstp Parameter Name Description Valid values: 1 ~ 28Type: Mandatory stp Show STP port information.
3.2.42 show interface gigabit vlan
Description Show VLAN information per gigabit port. Syntax show interface gigabitvlan Parameter Name Description Valid values: 1 ~ 28Type: Mandatory vlan Show VLAN information.
3.2.43 show jumboframe
Description Show jumbo frame settings. Syntax show jumboframe Parameter None
3.2.44 show stp
Description System Wide Spanning Tree Setting/Status. Syntax show stp Parameter None
3.2.45 show vlan
Description Show bridge port memberset/status. Syntax show vlan Parameter None
3.2.46 show vlan
Description Show bridge port member set/status per VLAN index (1~4094). Syntax show vlan Parameter Name Description Valid values: 1~4094Type: Mandatory.
3.2.47 show cos-queue-mapping
Description Show CoS queue mapping table. Syntax show cos-queue-mapping Parameter None
3.2.48 show interface gigabit qos
Description Show QoS per gigabit port. Syntax show interface gigabitqos Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.2.49 show policer
Description Show ingress policer table. Syntax show policer Parameter None
3.2.50 show profile acl {|all}
Description Show ACL profile detail information. Syntax show profile acl {|all}. Parameter Name Description Valid values: 1 ~ 20Type: Mandatory all Show all ACL profile.
3.2.51 show interface gigabit acl
Description Show ACL profile per gigabit port. Syntax show interface gigabitacl Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.2.52 show queue-scheduler profile
Description Show scheduler profile table. Syntax show queue-scheduler profile Parameter None
3.2.53 show queue-shaper
Description Show queue shaper information. Syntax show queue-shaper Parameter None
3.2.54 show port-shaper
Description Show port shaper information. Syntax show port-shaper Parameter None
3.2.55 show port-isolation
Description Show all port isolation information. Syntax show port-isolation Parameter None
3.2.56 show interface gigabit port-isolation
Description Show isolation information per gigabit port. Syntax show interface gigabitport-isolation Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.2.57 show interface gigabit storm-control
Description Show storm control information per gigabit port. Syntax show interface gigabitstorm-control Parameter Name Description Valid values: 1~28Type: Mandatory
3.2.58 show vlan {unknown-uc|unknown-mc|broadcast}
Description Show storm control information by VLAN. Syntax show vlan unknown-ucshow vlan unknown-mcshow vlan broadcast Parameter Name Description unknown-uc Show unknown unicast storm control information by VLAN.Type: Mandatory unknown-mc Show unknown multicast storm control information by VLAN.Type: Mandatory broadcast Show broadcast storm control information by VLAN.Type: Mandatory
3.2.59 show port-mirror
Description Show port mirror information. Syntax show port-mirror Parameter None
3.2.60 show interface gigabit rmon-counter
Description Show Ethernet counter per gigabit port. Syntax show interface gigabitrmon-counter Parameter Name Description Valid values: 1~28.Type: Mandatory
3.2.61 show interface vlan igmp
Description Show IGMP VLAN information. Syntax show interface vlan igmpshow interface vlanigmp Parameter Name Description Valid values: 1~4094.Type: Optional
3.2.62 show multicast-fdb
Description Show IGMP VLAN multicast forwarding table. Syntax show multicast-fdbshow multicast-fdb vlanshow multicast-fdb interface gigabit Parameter Name Description Valid values: 1~4094.Type: Optional Valid values: 1~28.Type: Optional
3.2.63 show multicast-fdb static
Description Show IGMP VLAN static multicast forwarding table. Syntax show multicast-fdb staticshow multicast-fdb static vlanshow multicast-fdb static interface gigabit Parameter Name Description Valid values: 1~4094.Type: Optional Valid values: 1~28.Type: Optional
3.2.64 show ring
Description Show ring protection configuration. Syntax show ring Parameter None
3.2.65 show ssl decrypted
Description Show ssl certificate with decrypted format. Syntax show ssl decrypted Parameter None
3.2.66 show ssl encrypted
Description Show ssl certificate with encrypted format. Syntax show ssl encrypted Parameter None
3.2.67 show interface gigabit
Description Show interface gigaport information Syntax show interface gigabit Parameter Name Description Gigabit port. Valid values: 1 ~ 28 Type: Mandatory
3.2.68 show ext-tpid
Description Show TPID for the VLAN Tag Syntax show ext-tpid Parameter None
3.2.69 show interface vlan
Description Show VLAN interface information of all VLANs. Syntax show interface vlan Parameter None
3.2.70 show interface vlan
Description Show VLAN interface information of specify VLAN. Syntax show interface vlan Parameter Name Description VLAN ID. Valid values: 1 ~ 4094 Type: Mandatory
3.2.71 show protocol-vlan
Description Show protocol based VLAN information for all entries. Syntax show protocol-vlan Parameter None
3.2.72 show interface gigabit vlan
Description Show vlan information per port Syntax show interface gigabitvlan Parameter Name Description Gigabit port. Valid values: 1 ~ 28 Type: Mandatory
3.2.73 show vlan-trans
Description Show VLAN translation table for all Syntax show vlan-trans Parameter None
3.2.74 show igmp-mvr-profile {|all}
Description Show IGMP MVR profile Syntax Show profile igmp-mvr-profile {|all} Parameter Name Description IGMP MVR profile number. Valid values: 1 ~ 15 Type: Mandatory
3.2.75 show igmp-acl-profile {|all}
Description Show IGMP ACL profile Syntax Show profile igmp-acl-profile {|all} Parameter Name Description IGMP ACL profile number. Valid values: 1 ~ 15 Type: Mandatory
3.2.76 show interface gigabit igmp
Description Show IGMP information per port. Syntax show interface gigabitigmp Parameter Name Description Gigabit port. Valid values: 1 ~ 28 Type: Mandatory
3.2.77 show interface vlan igmp
Description Show IGMP information. Syntax show interface vlan igmp Parameter None
3.2.78 show interface vlan igmp
Description Show IGMP information per vlan Syntax show interface vlanigmp Parameter Name Description VLAN ID. Valid values: 1 ~ 4094 Type: Mandatory
3.2.79 show multicast-fdb srclist
Description Show multicast source list table. Syntax show multicast-fdb srclist Parameter None
3.2.80 show multicast-fdb
Description Show IGMP group membership table Syntax show multicast-fdb Parameter None
3.2.81 show dot1x
Description Show dot1x information. Syntax show dot1x Parameter None
3.2.82 show dot1x pae-info-status {|all}
Description Show dot1x PAE status. Syntax show dot1x pae-info-status{|all} Parameter Name Description Gigabit port. Valid values: 1 ~ 28 Type: Mandatory
3.2.83 show dot1x eapol-stats {|all}
Description Show dot1x EAPOL stats. Syntax show dot1x eapol-stats{|all} Parameter Name Description Gigabit port. Valid values: 1 ~ 28 Type: Mandatory
3.2.84 show dot1x radius-stats
Description Show dot1x radius stats. Syntax show dot1x radius-stats Parameter None
3.2.85 show http
Description show http and https information. Syntax show http Parameter None
3.2.86 show interface trunk-group
Description show trunk group information. Syntax show interface trunk-group Parameter None
3.2.87 showfdb interface trunk-group
Description Show forwarding table per trunk group. Syntax show fdb interface trunk-group Parameter Name Description Trunk group. Valid values: 1 ~ 2 Type: Mandatory
3.2.88 showfdb
Description Show forwarding table. Syntax show fdb Parameter None
3.2.89 showfdb vlan
Description Show forwarding table per VLAN. Syntax show fdb vlan Parameter Name Description VLAN IDValid values: 1 ~ 4094Type: Mandatory
3.2.90 sleep
Description Sleep for the specified number of milli-seconds Syntax sleep Parameter Name Description Valid values: 1 ~ 0xFFFFFFFF msType: Mandatory
3.2.91 system restart
Description Restart System Syntax system restart Parameter None
3.2.92 system stop
Description Stop FTP transfer Syntax system stop Parameter None
3.2.93 telnet
Description Telnet to a remote host Syntax telnet Parameter Name Description Type: Mandatory
3.2.94 traceroute
Description Print the route packets take to network host Syntax traceroute Parameter Name Description Type: Mandatory
Commands that can be executed under Configure Mode
3.3.1 bye
Description Quit CLI. Syntax bye Parameter None
3.3.2 disable
Description Enter init mode. Syntax disable Parameter None
3.3.3 !
Description Execute the specific number of command in history Syntax ! Parameter Name Description Valid values: 1 ~ 32Type: Mandatory
3.3.4 interface gigabit
Description Gigabit Ethernet interface. (enter gigabit interface mode) Syntax interface gigabit Parameter Name Description Valid values: 1 ~ 28Type: Mandatory
3.3.5 interface trunk-group
Description Trunk group interface Syntax interface trunk-group Parameter Name Description < number> Valid values: 1 ~ 2Type: Mandatory
3.3.6 interface vlan
Description Vlan Ethernet interface (enter mode of interface vlan) Syntax interface vlan Parameter Name Description Valid values: 1 ~ 4094Type: Mandatory
3.3.7 profile acl
Description Enter Acl Profile Config Mode Syntax profile acl Parameter None
3.3.8 profile alarm
Description Alarm Profile Config Mode Syntax profile alarm Parameter None
3.3.9 profile igmp-acl
Description Enter IGMP ACL profile config mode Syntax profile igmp-acl Parameter None
3.3.10 profile igmp-mvr
Description Enter IGMP MVR profile config mode Syntax profile igmp-mvr Parameter None
3.3.11 profile sch
Description Enter Scheduling Profile Config Mode Syntax profile sch Parameter None
Description Prompt (1 ~ 31 characters) Syntax promote Parameter None
Description Set prompt to default Syntax promote default Parameter None
3.3.14 sntp polling-interval
Description Set SNTP Polling interval. Syntax sntp polling-interval Parameter Name Description Valid values: 60 ~ 65535 seconds, 0: disable polling Type: Mandatory
3.3.15 sntp server address
Description Set SNTP server address. Syntax sntp server address Parameter Name Description Type: Mandatory
3.3.16 sntp sync
Description Manual SNTP synchronization. Syntax sntp sync Parameter None
3.3.17 time set timezone
Description Set time zone. Syntax time set timezone<timezone>time set timezone default Parameter Name Description Valid values: please see 'list timezone'Type: Mandatory default Set time zone to default (GMT/UTC).Type: Mandatory
3.3.18 time set {date|time}
Description Set date/time. Syntax time set date time set time time set time Parameter Name Description Valid values: 1 ~ 12Type: Mandatory Valid values: 1 ~ 31Type: Mandatory Valid values: 0 ~ 36Type: Mandatory Valid values: 0 ~ 23Type: Mandatory Valid values: 0 ~ 59Type: Mandatory Valid values: 0 ~ 59Type: Optional
3.3.19 account add
Description Add an account. Syntax account add <username>account add <username> password <password>account add <username> password <password> comment <comment>account add <username> password <password> level <account_level>account add <username> password <password> level <account_level> comment <comment> Parameter Name Description Valid values: 1 ~ 31 charactersType: Mandatory Valid values: 0 ~ 31 charactersType: Mandatory Valid values: superuser engineer guestType: Mandatory Valid values: 0 ~ 31 charactersType: Mandatory
3.3.20 account delete
Description Delete an account. Syntax account delete Parameter Name Description Valid values: 1 ~ 31 charactersType: Mandatory
3.3.21 account modify
Description Modify an account Syntax account modifycommentaccount modifylevelaccount modifylevelaccount modifypasswordaccount modifypasswordaccount modifypasswordaccount modifypasswordaccount modifypassword commentlevelaccount modifypasswordpasswordaccount modifypassword Parameter Name Description Valid values: 1 ~ 31 charactersType: Mandatory Valid values: 0 ~ 31 charactersType: Mandatory Valid values:dsuperuserengineerguestType: Mandatory Valid values: 0 ~ 31 charactersType: Mandatory
3.3.22 kick { cli|console|web}
Description Kick off a logged-in user. Syntax kickCLI kickconsole kickweb Parameter Name Description Valid values: 1 ~ 10Type: Mandatory
3.3.23 syslog server
Description Configure syslog server IP address. Syntax syslog server Parameter Name Description Syslog server IP address.Type: Mandatory
3.3.24 syslog {enable|disable}
Description Disable or enable syslog service. Syntax syslog enablesyslog disable Parameter None
3.3.25 setenv pagefilter
Description Configure Page Filter Syntax setenv pagefilter Parameter Name Description Enable Page FilterValid values: (0:disable, 1:enable)Type: Mandatory
3.3.26 setenv script-delay
Description Configure script delay Syntax setenv script-delay Parameter Name Description Script DelayValid values: 1 ~ 0xFFFFFFFF msType: Mandatory
3.3.27 setenv show-date-time-in-prompt
Description Show Date/Time in Prompt (0:disable, 1:enable) Syntax setenv show-date-time-in-prompt Parameter Name Description enabledValid values: (0:disable, 1:enable)Type: Mandatory
3.3.28 clisettings
Description Configure CLI settings. Syntax clisettings<timeout>clisettings<timeout><flag>clisettings<timeout><flag><maxSessions> Parameter Name Description Valid values: 60 ~ 65535 seconds, 0: no timeoutType: Mandatory Valid values: bitmap□ showAla rm(0)□ showEvent(1)□ showReadWriteStatus(2)Type: Optional Valid values: 1 ~ 10 sessionsType: Mandatory
3.3.29 runningcfg clear
Description Clear configuration. Syntax runningcfg clear all runningcfg clear all norebootrunningcfg clear generalrunningcfg clear general noreboot Parameter Name Description all Clear all configuration. Type: Mandatory general Clear general configuration. Type: Mandatory noreboot Clear configuration without Reboot. Must reboot system manually for the changes to take effect! Type: Optional
3.3.30 runningcfg get {binary|cli}
Description Get exported configuration files from a FTP server. Syntax runningcfg get <ip> <username> <password> binary <string> runningcfg get <ip> <username> <password> cli <string> Parameter Name Description Type: Mandatory Valid values: 1 ~ 32 charactersType: Mandatory Valid values: 1 ~ 32 charactersType: Mandatory binary Get two binary images.Type: Mandatory cli Get two CLI scripts.Type: Mandatory Remote filename prefix.Valid values: 1 ~ 64 charactersType: Mandatory
3.3.31 runningcfg import download
Description Import configuration from files retrieved via 'runningcfg get'. Syntax runningcfg import download binary runningcfg import download binary noreboot runningcfg import download cli runningcfg import download cli noreboot Parameter Name Description binary Import configuration from binary images retrieved via 'runningcfg get'.Type: Mandatory cli Import configuration from the CLI scripts retrieved via 'runningcfg get'.Type: Mandatory Noreboot Import configuration without Reboot. Must reboot system manually for the changes to take effect!Type: Optional
3.3.32 runningcfg put {binary|cli}
Description Put exported configuration files to a FTP server. Syntax runningcfg put <ip> <username> <password> binary <string> runningcfg put <ip> <username> <password> cli <string> Parameter Name Description Type: Mandatory Valid values: 1 ~ 32 charactersType: Mandatory Valid values: 1 ~ 32 charactersType: Mandatory binary Put two binary images.Type: Mandatory cli Put CLI scripts.Type: Mandatory Remote filename prefix.Valid values: 1 ~ 64 charactersType: Mandatory
3.3.33 runningcfg replace-save
Description Save running config to FLASH replacing existing the specified backup. Syntax runningcfg replace-save<inbandBackupIndex>runningcfg replace-save<inbandBackupIndex><inbandBackupName>runningcfg replace-save<inbandBackupIndex><inbandBackupName><generalBackupIndex>runningcfg replace-save<inbandBackupIndex><inbandBackupName><generalBackupIndex><generalBackupName> Parameter Name Description Valid values: 1 ~ 16Type: Mandatory Valid values: 1 ~ 31 charactersType: Optional Valid values: 1 ~ 16Type: Optional Valid values: 1 ~ 31 charactersType: Optional
3.3.34 runningcfg restore index
Description Restore configuration. Syntax runningcfg restore indexrunningcfg restore indexrunningcfg restore indexnoreboot Parameter Name Description Valid values: 1 ~ 16Type: Mandatory Valid values: 1 ~ 16Type: Optional (if omitted, use the same index as) noreboot Restore database without reboot. Must reboot system manually for the changes to take effect!Type: Optional
3.3.35 runningcfg restore name
Description Restore configuration. Syntax runningcfg restore name<inbandBackupName>runningcfg restore name<inbandBackupName><generalBackupName>runningcfg restore name<inbandBackupName><generalBackupName>noreboot Parameter Name Description Valid values: 1 ~ 31 charactersType: Mandatory Valid values: 1 ~ 31 charactersType: Optional (if omitted, use the same name as) noreboot Restore database without reboot. Must reboot system manually for the changes to take effect!Type: Optional
3.3.36 runningcfg save
Description Save running config to FLASH. Syntax runningcfg saverunningcfg saverunningcfg save Parameter Name Description Valid values: 1 ~ 31 charactersType: Optional Valid values: 1 ~ 31 charactersType: Optional (if omitted, use the same name as)
3.3.37 firmware partition
Description Set boot partition. Syntax firmware partition Parameter Name Description Valid values: 0 ~ 1Type: Mandatory
3.3.38 firmware write
Description Perform Remote Download.Schedule a remote download (scheduled upgrade).Cancel a scheduled upgrade. Syntax firmware write <ip> <username> <password> <string> {bootloader| image}firmware write <ip> <username> <password> <string> {bootloader| image}{noreboot}|<time>}firmware write <ip> <username> <password> <string> {bootloader| image}noreboot <time>firmware write cancel Parameter Name Description Type: Mandatory Valid values: 1 ~ 32 charactersType: Mandatory Valid values: 0 ~ 32 charactersType: Mandatory Image path and filename.Valid values: 1 ~ 64 charactersType: Mandatory image Perform remote download for the software image.Type: Mandatory bootloader Perform remote download for the boot loader.Type: Mandatory noreboot Perform Remote Download without Reboot.Must reboot system manually for the changes to take effect!Type: Optional Time for scheduled upgrade.(MM/DD/YYYY HH:MM:SS)Type: Optional cancel Cancel scheduled upgrade.Type: Mandatory
3.3.39 system restart
Description Restart system. Syntax system restartsystem restart Parameter system restart Name Description Time for scheduled restart.(MM/DD/YYYY HH:MM:SS)Type: Optional
3.3.40 system restart cancel
Description Cancel a previously-scheduled system restart. Syntax system restart cancel Parameter None
3.3.41 system dump
Description Dump system to a FTP server Syntax system dump Parameter Name Description FTP server IP addressType: Mandatory UsernameValid values: 1 ~ 32 charactersType: Mandatory PasswordValid values: 0 ~ 32 charactersType: Mandatory Remote filenameValid values: 1 ~ 64 charactersType: Mandator
3.3.42 system stop ftp
Description Stop FTP transfer Syntax system stop ftp Parameter None
3.3.43 route add netmask gateway
Description Add a route Syntax route addnetmaskgateway Parameter Name Description Destination network address. Type: Mandatory Type: Mandatory Type: Mandatory
3.3.44 route delete netmask
Description Delete a route. Syntax route delete<netmask> netmask Parameter Name Description Destination network address.Type: Mandatory Type: Mandatory
3.3.45 default-gateway
Description Configure default gateway IP address. Syntax default-gateway Parameter Name Description Type: Mandatory
3.3.46 ip-address
Description Configure IP address / netmask / gateway. Syntax ip-address ip-address netmask ip-address Parameter Name Description Type: Mandatory Type: Optional Type: Optional
3.3.47 default all
Description Set all configurations to default. Syntax default alldefault all except account Parameter Name Description except account Set all configurations to default except user account.Type: Mandatory
3.3.48 list timezone
Description List timezones. Syntax list timezone Parameter None
Description Modify system contact. Syntax system-info contact Parameter Name Description Valid values: 0 ~ 255 characters (ASCII code: 0x20 - 0x7E)Type: Mandatory
3.3.50 system-info location
Description Modify system location. Syntax system-info location Parameter Name Description Valid values: 0 ~ 255 characters (ASCII code: 0x20 - 0x7E)Type: Mandatory
3.3.51 system-info name
Description Modify system name. Syntax system-info name Parameter Name Description Valid values: 1 ~ 255 characters (ASCII code: 0x21 - 0x7E) Type: Mandatory
3.3.52 http port {|default}
Description Set HTTP server port. Syntax http port http port default Parameter Name Description Valid values: 1 ~ 65535Type: Mandatory default Set http server port to default (80)Type: Mandatory
3.3.53 temperature shift down
Description Set downshift time. Syntax temperature shift down Parameter Name Description Valid values: 1 ~ 255 secondsType: Mandatory
3.3.54 temperature shift up
Description Set upshift time. Syntax temperature shift up Parameter Name Description Valid values: 1 ~ 255 secondsType: Mandatory
3.3.55 temperature threshold down
Description Set downshift temperature threshold. Syntax temperature threshold down Parameter Name Description Valid values: -55 ~ 85 degrees CentigradeType: Mandatory
3.3.56 temperature threshold up
Description Set upshift temperature threshold. Syntax temperature threshold up Parameter Name Description Valid values: -55 ~ 85 degrees CentigradeType: Mandatory
3.3.57 vlan
Description Configure VLAN. Syntax vlan Parameter Name Description Create an empty VLAN index. Valid values: 1 ~ 4094Type: Mandatory
3.3.58 vlan { | broadcast | disable | unknown-mc | unknown-uc} {block | forward}
Description Configure VLAN's name. Syntax vlan {| broadcast | disable | unknown-mc | unknown-uc} { block | forward} Parameter Name Description Create an empty VLAN index. Valid values: 1 ~ 4094 Type: Mandatory VLAN Name (0~31) String Size:0~31 Type: Mandatory broadcast Set storm control for broadcast packet per VLAN disable Delete VLAN memberset/settting unknown-mc Set storm control for unknown multicast packet per VLAN unknown-uc Set storm control for unknown unicast packet per VLAN block Block broadcast packet forward Forward broadcast packet
3.3.59 vlan disable
Description Delete VLAN memberset/setting. Syntax vlan disable Parameter Name Description Valid values: 1 ~ 4094Type: Mandatory
3.3.60 aging
Description Configure aging time for a bridge port. Syntax aging Parameter Name Description Valid values: 10 ~ 600 (seconds)Type: Mandatory
3.3.61fdb-delete all
Description Delete all dynamic entries from forwarding table. Syntax fdb-delete all Parameter Name Description all Delete all dynamic FDB entries. Type: Mandatory
3.3.62fdb-delete interface gigabit
Description Delete Forwarding table entries per gigabit port. Syntax fdb-delete interface gigabit Parameter Name Description Valid values: 1~28Type: Mandatory
3.3.63fdb-delete vlan
Description Delete forwarding table entries per VLAN index. Syntax fdb-delete vlan Parameter Name Description Valid values: 1~4094Type: Mandatory
3.3.64fdbstatic interface gigabit
Description Create static MAC forwarding table entry. Syntax fdbstaticinterface gigabit Parameter Name Description Entry position. Valid values: 1~512 Type: Mandatory Valid values: 1~28 Type: Mandatory Valid values: 1~4094 Type: Mandatory Valid values: xx:xx:xx:xx:xx:xx Type: Mandatory
3.3.65 fdbstatic delete
Description Delete static MAC forwarding table entry. Syntax fdbstatic delete Parameter Name Description Valid values: 1~512Type: Mandatory
3.3.66 fdbstatic delete all
Description Delete all entries of static MAC forwarding table. Syntax fdbstatic delete all Parameter None
3.3.67fdbstatic delete interface gigabit
Description Delete static MAC forwarding table entry per gigabit port. Syntax fdbstatic delete interface gigabit Parameter Name Description Valid values: 1~28Type: Mandatory
3.3.68fdbstatic delete vlan
Description Delete static MAC forwarding table entry per VLAN index. Syntax fdbstatic delete vlan Parameter Name Description Valid values: 1~4094Type: Mandatory
3.3.69 stp {disable|enable}
Description Configure spanning tree protocol settings. Syntax stp {disable|enable} Parameter Name Description disable Disable STP. enable Enable STP.
3.3.70 stp bpdu {deny|flooding}
Description Set BPDU packet filter (deny/flooding). Syntax stp bpdu {deny|flooding} Parameter Name Description deny Deny BPDU packet. flooding Flood BPDU packet.
3.3.71 stp forward-delay
Description Set STP forward delay time. Syntax stp forward-delay Parameter Name Description Valid values: 4 ~ 30 (seconds)Type: Mandatory
3.3.72 stp hello-time
Description Set STP hello time. Syntax stp hello-time Parameter Name Description Valid values: 1 ~ 10 (seconds)Type: Mandatory
3.3.73 stp max-age
Description Set STP max age value. Syntax stp max-age Parameter Name Description Valid values: 6 ~ 40 (seconds)Type: Mandatory
3.3.74 stp msti { add | create | delete | set} { | range}
Description Set MSTP instance Syntax stp msti { add | create | delete | set} { | range } Parameter Name Description MSTP instanceValid values: 1~10Type: Mandatory add Add VLAN ID to MSTP instance create Create MSTP instance delete Delete MSTP instance set Set MSTP instance name VLAN IDValid values: 1~4094 range Add multiple VLAN ID to MSTP instance
3.3.75 stp priority
Description Set STP priority. Syntax stp priority Parameter Name Description Valid values: 0 ~ 61440 step 4096Type: Mandatory
3.3.76 stp region-name
Description Set STP Region Name Syntax stp region-name Parameter Name Description Region NameValid values: Length 0..32Type: Mandatory
3.3.77 stp revision
Description Set MST Revision Level Syntax stp revision Parameter Name Description Revision Level valueValid values: 0..65535Type: Mandatory
3.3.78 stp version {stp|rstp|mstp}
Description Set STP version. Syntax stp version {stp|rstpmstp} Parameter Name Description stp Spanning tree protocol. rstp Rapid spanning tree protocol. mstp Multiple Spanning Tree Protocol
3.3.79 jumboframe {enable|disable}
Description Set jumbo frame settings. Syntax jumboframe {enable|disable} Parameter Name Description enable Enable jumbo frame. disable Disable jumbo frame.
3.3.80 jumboframe mtu
Description MTU size. Syntax jumboframe mtu Parameter Name Description Range. Valid values: 1536~9000 (bytes) Type: Mandatory
3.3.81 cos-queue-mapping cos queue
Description Set CoS and queue mapping. Syntax cos-queue-mapping cos < priority> queue < number> Parameter Name Description Valid values: 0~7Type: Mandatory Valid values: 0~7Type: Mandatory
3.3.82 policer cos-mark green yellow red
Description Set ingress policer CoS remark mapping table. Syntax policer cos-mark greenyellowred Parameter Name Description Color green and CoS number mapping. Valid values: 0~7 Type: Mandatory Color yellow and CoS number mapping. Valid values: 0~7 Type: Mandatory Color red and CoS number mapping. Valid values: 0~7 Type: Mandatory
3.3.83 policer dscp-mark green yellow red
Description Set ingress policer DSCP remark mapping table. Syntax policer dscp-mark greenyellowred Parameter Name Description Color green and DSCP number mapping. Valid values: 0~63 Type: Mandatory Color yellow and DSCP number mapping. Valid values: 0~63 Type: Mandatory Color red and DSCP number mapping. Valid values: 0~63 Type: Mandatory
3.3.84 policer ingress-color {aware|blind}
Description Enable/Disable ingress-color function. Syntax policer ingress-color {aware|blind} Parameter Name Description aware Enable ingress color function. blind Disable ingress color function.
3.3.85 policer ingress-color cos {red|yellow|green}
Description Set ingress-color mapping table. Syntax policer ingress-color cos {green|yellow|red} Parameter Name Description Valid values: 0~7Type: Mandatory green|yellow|red Green or yellow or red.Type: Mandatory
3.3.86 mirror analyzer-port {enable|disable}
Description Enable/Disable analyzer port configuration. Syntax mirror analyzer-port {enable|disable} Parameter None Name Description enable Enable port mirror. disable Disable port mirror.
3.3.87 mirror analyzer-port
Description Set analyzer port. Syntax mirror analyzer-port Parameter Name Description Valid values: 1~28Type: Mandatory
3.3.88 vlan unknown-uc {blcok|forward}
Description Block/ Forward unknown unicast packet per VLAN. Syntax vlanunknown-uc blockvlanunknown-uc forward Parameter Name Description Valid values: 1~4094Type: Mandatory
3.3.89 vlan unknown-mc {block|forward}
Description Block/Forward unknown multicast packet per VLAN. Syntax vlan <vlanid> unknown-mc blockvlan <vlanid> unknown-mc forward Parameter Name Description Valid values: 1~4094Type: Mandatory
3.3.90 vlan broadcast {block|forward}
Description Block/Forward broadcast packet per VLAN. Syntax vlan <vlanid> broadcast blockvlan <vlanid> broadcast forward Parameter Name Description Valid values: 1~4094Type: Mandatory
3.3.91 port-mirror monitor-port
Description Set the gigabit port to be monitored. Syntax port-mirror monitor-port Parameter Name Description Valid values: 1~28Type: Mandatory
3.3.92 port-mirror {enable|disable}
Description Enable/Disable port mirror. Syntax port-mirror enableport-mirror disable Parameter None
3.3.93 port-mirror {tx-analyzer-port|rx-analyzer-port}
Description Set Tx analyzer port (monitor 'out' packet of monitored port)/Rx analyzer port (monitor 'in' packet of monitored port). Syntax port-mirror tx-analyzer-portport-mirror rx-analyzer-port Parameter Name Description Valid values: 1~28Type: Mandatory
3.3.94 counter interface-counter clear
Description Clear interface counter per gigabit port. Syntax counter interface-counter clear Parameter Name Description Valid values: 1~28.Type: Mandatory
3.3.95 counter rmon-counter clear
Description Clear Ethernet counter per gigabit port. Syntax counter rmon-counter clear Parameter Name Description Valid values: 1~28.Type: Mandatory
3.3.96 multicast-fdb delete all
Description Delete multicast forwarding table. Syntax multicast-fdb delete allmulticast-fdb delete vlanmulticast-fdb delete interface gigabit Parameter Name Description Valid values: 1~4094.Type: Mandatory Valid values: 1~28.Type: Mandatory
3.3.97 multicast-fdb static delete
Description Delete static multicast forwarding table. Syntax multicast-fdb static deletemulticast-fdb static delete allmulticast-fdb static delete vlanmulticast-fdb static delete interface gigabit Parameter Name Description Static multicast forwarding table entry index. Valid values: 1~128Type: Mandatory Valid values: 1~4094.Type: Mandatory Valid values: 1~28.Type: Mandatory
3.3.98 multicast-fdb static interface gigabit
Description Create static IGMP VLAN forwarding table entry. Syntax multicast-fdb staticinterface gigabit Parameter Name Description Static multicast forwarding table entry index. Valid values: 1~128Type: Mandatory Valid values: 1~28.Type: Mandatory Valid values: 1~4094.Type: Mandatory IGMP VLAN group IP address. Valid values: 224.0.0.0~239.255.255.255Type: Mandatory
3.3.99 ring-group
Description Entry ring group interface Syntax ring-group Parameter Name Description Ring group indexValid values: 1~3Type: Mandatory
3.3.100 ext-tpid
Description Set tpid. Syntax ext-tpid Parameter Name Description tpidValid values: 0x0001~0xffffType: Mandatory
3.3.101 profile igmp-mvr
Description Entry IGMP MVR interface. Syntax profile igmp-mvr Parameter None
3.3.102 profile igmp-acl
Description Entry IGMP ACL interface. Syntax profile igmp-acl Parameter None
3.3.103 dot1x {enable|disable}
Description Enable / disable dot1x. Syntax dot1x {enable|disable} Parameter None
3.3.104 dot1x radius set
Description Set dot1x parameters. Syntax dot1x radius set Parameter Name Description IP address.Format: 0.0.0.0 ~ 255.255.255.255Type: Mandatory Authentication port.Valid values: 1 ~ 65535Default values: 1812Type: Mandatory Authentication key.Length: 1 ~ 16Type: Mandatory
3.3.105 dot1x clear eapol-stats {|all}
Description Clear dot1x EAPOL stats. Syntax dot1x clear eapol-stats {|all} Parameter Name Description Gigabit port. Valid values: 1 ~ 28 Type: Mandatory
3.3.106 dot1x clear dot1x-radius-stats
Description Clear dot1x radius-stats Syntax dot1x clear dot1x-radius-stats Parameter None
3.3.107 https {enable|disable}
Description Enable/Disable https. Syntax https {enable|disable} Parameter None
3.3.108 https port {default}
Description Set https port by specific port or default port. Syntax https port {|default} Parameter https port number. Valid values: 1 ~ 65535 Type: Mandatory default https default port number is 443. Type: Mandatory
3.3.109 interface trunk-group
Description Enter trunk group configure mode. Syntax interface trunk-group Parameter Trunk group index. Valid values: 1 ~ 2 Type: Mandatory
3.3.110 fdb-delete interface trunk-group
Description Delete forwarding table per trunk group. Syntax fdb-delete interface trunk-group Parameter Trunk group index. Valid values: 1 ~ 2 Type: Mandatory
3.3.111 ssl default-certificate
Description Use system default SSL certificate Syntax ssl default-certificate Parameter None
3.3.112 ssl upload
Description Upload new SSL certificate Syntax ssl upload Parameter None
3.4 Interface gigabit Mode Commands
3.4.1 accfrm
Description Set acceptable frame type. Syntax Accfrm{all|tag|untag} Parameter Name Description all Accept all frames. tag Accept tagged frame only. untag Accept un-tagged frame only.
3.4.2 priority
Description Set user priority for the gigabit port. Syntax priority Parameter Name Description Valid values: 0 ~ 7Type: Mandatory
3.4.3 vlan
Description Join VLAN with default setting (tagged). Syntax vlan Parameter Name Description Valid values: 1~4094Type: Mandatory
3.4.4 vlan disable
Description Leave joined VLAN. Syntax vlandisable Parameter Name Description Valid values: 1~4094Type: Mandatory disable Leave joined VLAN
3.4.5 vlan tag
Description Join tagged VLAN. Syntax vlan <vlanid> tag Parameter Name Description Valid values: 1~4094Type: Mandatory tag Join Tagged VLAN
3.4.6 vlan untag
Description Join untagged VLAN. Syntax vlanuntag Parameter Name Description Valid values: 1~4094 Type: Mandatory untag Join Untagged VLAN
3.4.7 stpport {disable|enable}
Description Configure STP port. Syntax stpport {disable|enable} Parameter Name Description disable Disable STP port. enable Enable STP port.
3.4.8 stpport cost
Description Set STP port path cost. Syntax stpport cost Parameter Name Description Valid values: 1 ~ 200000000Type: Mandatory
3.4.9 stpport edge-port {enable|disable}
Description Set STP port edge-type. Syntax stpport edge-port {enable|disable} Parameter Name Description enable Set as edge-type. disable Set as none edge-type.
3.4.10 stpport priority
Description Set STP port priority. Syntax stpport priority Parameter Name Description Valid values: 0~240 step 16Type: Mandatory
3.4.11 flow-control {enable|disable}
Description Enable/Disable flow-control. Syntax flow-control {enable|disable} Parameter Name Description enable Enable flow-control. disable Disable flow-control.
3.4.12 speed
Description Configure copper port Ethernet speed. Syntax speed{auto|full-1000mbps|full-100mbps|full-10mbps|half-100mbps|half-10mbps} Parameter Name Description auto Auto negotiation. full-1000mbps Set 1000Mbps full duplexing. full-100mbps Set 100Mbps full duplexing. full-10mbps Set 10Mbps full duplexing. half-100mbps Set 100Mbps half duplexing. half-10mbps Set 10Mbps half duplexing.
3.4.13 sfp-speed (for 10G ports)
Description Configure 10G fiber port Ethernet speed. Syntax speed {auto|full-l000mbps|full-10Gbps} Parameter Name Description auto Auto negotiation. full-l000mbps Set 1000Mbps full duplexing. full-10Gbps Set 10Gbps full duplexing.
3.4.14 sfp-speed (for 1G ports)
Description Configure fiber port Ethernet speed. Syntax speed {auto|full-I000mbps|full-100mbps|full-2500mbps} Parameter Name Description auto Auto negotiation. full-I000mbps Set 1000Mbps full duplexing. full-100mbps Set 100Mbps full duplexing.
3.4.15 port {enable/disable}
Description Set interface gigabit port enable or disable. Syntax port {enable/disable} Parameter Name Description disable Turn off gigabit port. enable Turn off gigabit port.
3.4.16 default vlan
Description Set default VLAN to gigabit port. Syntax default vlan Parameter Name Description Valid values: 1 ~ 4094Type: Mandatory
3.4.17 policer pir pbs cir cbs {drop|cos|dscp}
Description Set ingress policer parameters. Syntax policer pirpbscbrbs{drop|cos|dscp} Parameter Name Description Ingress total max rate setting. Valid values: 1~1000000 Type: Mandatory Ingress queue size setting. Valid values: 1~65535 Type: Mandatory Ingress max rate for first stage setting. Valid values: 1~1000000 Type: Mandatory Ingress max rate for second stage setting. Valid values: 1~65535 Type: Mandatory {drop|cos|dscp} Policer type Type: Mandatory
3.4.18 policer disable
Description Disable policer function. Syntax policer disable Parameter None
3.4.19 acl-profile-bind
Description Port ACL profile binding. Syntax acl-profile-bind Parameter Name Description Valid values: 1~10Type: Mandatory
3.4.20 def-acl {permit|deny}
Description Set port default ACL rule. Syntax def-acl permitdef-acl deny Parameter None
3.4.21 queue-scheduler bind
Description Scheduler profile binding. Syntax queue-scheduler bind Parameter Name Description Scheduler profile index. Valid values: 1~8 Type: Mandatory
3.4.22 port-shaper {enable|disable}
Description Enable/Disable port shaper. Syntax port-shaper {enable|disable} Parameter None
3.4.23 port-shaper
Description Set port shaper rate. Syntax port-shaper Parameter Name Description Valid values: 1~1000000Type: Mandatory
3.4.24 queue-shaper {enable|disable}
Description Enable/Disable queue shaper. Syntax queue-shaper {enable|disable} Parameter None
3.4.25 queue-shaper queue
Description Set queue shaper parameters. Syntax queue-shaper queue Parameter Name Description Valid values: 0~7Type: Mandatory Valid values: 1~1000000Type: Mandatory
3.4.28 unknown-uc {block|forward}
Description Block/ Forward unknown unicast packet. Syntax unknown-uc blockunknown-uc forward Parameter None
3.4.29 unknown-mc rate
Description Set storm rate for unknown multicast packet. Syntax unknown-mc rate Parameter Name Description Valid values: 1~1000000 (Kbps)Type: Mandatory
3.4.30 unknown-mc {block|forward}
Description Block/Forward unknown multicast packet. Syntax unknown-mc blockunknown-mc forward Parameter None
3.4.31 broadcast rate
Description Set storm rate for broadcast packet. Syntax broadcast rate Parameter Name Description Valid values: 1~1000000 (Kbps)Type: Mandatory
3.4.32 broadcast {block|forward}
Description Block/Forward broadcast packet. Syntax broadcast blockbroadcast forward Parameter None
3.4.33 vlan-stack {enable|disable}
Description Enable/disable vlan stack. Syntax vlan-stack {enable|disable} Parameter None
3.4.34 protocol-vlan create
Description Create protocol VLAN. Syntax protocol-vlancreate Parameter Name Description Protocol VLAN index. Valid values: 1 ~ 20 Type: Mandatory Ether type. Valid values: 0 ~ FFFF,(hex) Type: Mandatory Service VLAN (SVALN). Valid values: 1 ~ 4094 Type: Mandatory CoS of SVLAN. Valid values: 0 ~ 8 Type: Mandatory
3.4.35 protocol-vlan delete
Description Delete protocol VLAN. Syntax protocol-vlandelete Parameter Name Description Protocol VLAN index. Valid values: 1 ~ 20 Type: Mandatory
3.4.36 vlan-trans create many-to-
Description Create VLAN translation. Syntax vlan-transcreate Parameter Name Description VLAN translation index. Valid values: 1 ~ 20 Type: Mandatory Customer VLAN (CVLAN). Valid values: 1 ~ 4094 Type: Mandatory CoS of VLAN. Valid values: 0 ~ 8 Type: Mandatory Service VLAN (SVLAN). Valid values: 1 ~ 4094 Type: Mandatory CoS of SVLAN. Valid values: 0 ~ 8 Type: Mandatory
3.4.37 vlan-trans delete
Description Delete VLAN translation. Syntax vlan-transdelete Parameter Name Description VLAN translation index. Valid values: 1 ~ 20 Type: Mandatory
3.4.38 igmp mvrprofile
Description Binding IGMP MVR profile to specified port. Syntax igmp mvrprofile Parameter Name Description IGMP MVR index. Valid values: 1 ~ 15 Type: Mandatory
3.4.39 igmp aclprofile
Description Binding IGMP ACL profile to specified port. Syntax igmp aclprofile Parameter Name Description IGMP ACL index. Valid values: 1 ~ 15 Type: Mandatory
Description Enable for force PAE port re-initialize / re-authenticate. Syntax dot1x {force-reinitialize| force-reauthenticate} Parameter None
3.4.42 dot1x auth-port-control {auto| force-authorized| force-unauthorized}
Description Set dot1x authentication type of PAE port. Syntax dot1x auth-port-control {auto| force-authorized| force-unauthorized} Parameter None
3.4.43 dot1x auth-quiet-period
Description Set quiet period of PAE port Syntax dot1x auth-quiet-period Parameter Name Description The quiet period of PAE portValid values: 1 ~ 255 seconds.Default values: 60 secondsType: Mandatory
3.4.44 dot1x auth-tx-period
Description Set timeout of authenticator waiting for EAP-Response / Identity from supplication of PAE port Syntax dot1x auth-tx-period Parameter Name Description The quiet period of PAE portValid values: 1 ~ 255 seconds.Default values: 30 secondsType: Mandatory
Description Set timeout of authenticator wait for EAP-Response(exclude EAP-Request / Identify) after sending EAP-Request. Syntax dot1x auth-supp-timeout Parameter Name Description Authenticator timeout. Valid values: 1 ~ 255 seconds. Default values: 30 seconds Type: Mandatory
3.4.47 dot1x auth-server-timeout
Description Set timeout of Authenticator wait Access-Challenge / Access-Accept / Access-Reject after sending Access-Request Syntax dot1x auth-server-timeout Parameter Name Description Authenticator timeout. Valid values: 1 ~ 255 seconds. Default values: 30 seconds Type: Mandatory
3.4.48 dot1x reauth {enable|disable}
Description Enable/Disable re-authentication of APE port Syntax dot1x reauth {enable|disable} Parameter None
3.4.49 dot1x reauth-period
Description period of re-authentication of PAE port Syntax dot1x reauth-period Parameter Name Description Period of re-authentication. Valid values: 1 ~ 3600 seconds. Default values: 3600 seconds Type: Mandatory
3.5.1 acl-profile {create|delete}
Description Create/Delete ACL profile. Syntax acl-profile {create|delete} Parameter Name Description Valid values: 2~10Type: Mandatory create|delete Type: Mandatory
3.5.2 acl-profile {create|delete} entry
Description Create/Delete ACL profile entry. Syntax acl-profilecreate entryacl-profiledelete entry Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory
3.5.3 acl-profile set name
Description Set ACL profile name. Syntax acl-profileset name Parameter Name Description Valid values: 2~10Type: Mandatory Valid Length: 1~31Type: Mandatory
3.5.4 acl-profile set entry mac-type set vlan
Description Set VLAN index for ACL MAC type entry. Syntax acl-profileset entrymac-type set vlan Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory Valid values: 1~4094Type: Mandatory
3.5.5 acl-profile set entry mac-type set vlan any
Description Set VLAN index for ACL MAC type entry. Syntax acl-profileset entrymac-type set vlan any Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory
3.5.6 acl-profile set entry mac-type set {srcmac|dstmac}
Description Set MAC for ACL MAC type entry. Syntax acl-profileset entrymac-type set {srcmac|dstmac} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory srcmac|dstmac Source / Destination MAC AddressType: Mandatory Valid values: 00:00:00:00:00:00 ~FF:FF:FF:FF:FF:FFType: Mandatory Valid values: 00:00:00:00:00:00 ~FF:FF:FF:FF:FF:FFType: Mandatory
3.5.7 acl-profile set entry mac-type set ethertype
Description Set ether type for ACL MAC type entry. Syntax acl-profileset entrymac-type set ethertype Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory Valid values: 0x0001~0xFFFFType: Mandatory
3.5.8 acl-profile set entry mac-type set ethertype any
Description Set ether type for ACL MAC type entry. Syntax acl-profileset entrymac-type set ethertype any Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory
3.5.9 acl-profile set entry ipv4-type set {srcip|dstip}
Description Set IP for ACL IPv4 type entry. Syntax acl-profileset entryipv4-type set {srcip|dstip} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory srcip|dstip Source / Destination IP AddressType: Mandatory Valid values: 0.0.0.0 ~ 255.255.255.255Type: Mandatory Valid values: 0.0.0.0 ~ 255.255.255.255Type: Mandatory
3.5.10 acl-profile set entry ipv4-type set ip-protocol
Description Set protocol for ACL IPv4 type entry. Syntax acl-profileset entryipv4-type set ip-protocol Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory Valid values: 1~255Type: Mandatory
3.5.11 acl-profile set entry ipv4-type set ip-protocol any
Description Set protocol for ACL IPv4 type entry. Syntax acl-profileset entryipv4-type set ip-protocol any Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory
3.5.12 acl-profile set entry l4port-type set protocol {tcp|udp}
Description Set protocol for ACL L4Port type entry. Syntax acl-profileset entryl4port-type set protocol {tcp|udp} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory tcp|udp TCP or UDP packet.Type: Mandatory
3.5.13 acl-profile set entry l4port-type set {srcip|dstip}
Description Set IP for ACL L4Port type entry. Syntax acl-profileset entryl4port-type set {srcip|dstip} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory srcip|dstip Source / Destination IP AddressType: Mandatory Valid values: 0.0.0.0 ~ 255.255.255.255Type: Mandatory Valid values: 0.0.0.0 ~ 255.255.255.255Type: Mandatory
3.5.14 acl-profile set entry l4port-type set {srcport|dstport}
Description Set port for ACL L4Port type entry. Syntax acl-profileset entryl4port-type set {srcport|dstport} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory srcport|dstport Source / Destination portType: Mandatory Valid values: 1~65535Type: Mandatory
3.5.15 acl-profile set entry l4port-type set {srcport|dstport} any
Description Set port for ACL L4Port type entry. Syntax acl-profileset entryl4port-type set {srcport|dstport} any Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory srcport|dstport Source / Destination port.Type: Mandatory
3.5.16 acl-profile set entry tos-type set {srcip|dstip}
Description Set IP for ACL ToS type entry. Syntax acl-profileset entrytos-type set {srcip|dstip} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory srcip|dstip Source / Destination IP AddressType: Mandatory Valid values: 0.0.0.0 ~ 255.255.255.255Type: Mandatory Valid values: 0.0.0.0 ~ 255.255.255.255Type: Mandatory
3.5.17 acl-profile set entry tos-type set type {precedence|tos|dscp}
Description Set type for ACL ToS type entry. Syntax acl-profileset entrytos-type set type{precedence|tos|dscp} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory precedence|tos|dscp Precedence or ToS or DSCP Type.Type: Mandatory Precedence type.Valid values: 0~7Tos type.Valid values: 0~15DSCP type.Valid values: 0~63Type: Mandatory
3.5.18 acl-profile set entry tos-type set type any
Description Set type for ACL ToS type entry. Syntax acl-profileset entrytos-type set type any Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory
3.5.19 acl-profile set entry action forwarding {deny|permit}
Description Set ACL entry action is forwarding. Syntax acl-profileset entryaction forwarding{deny|permit} Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory deny|permit Deny or Permit forwarding.Type: Mandatory
3.5.20 acl-profile set entry action queue
Description Set ACL entry action to specific queue number. Syntax acl-profileset entryaction queue Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory Valid values: 0~7Type: Mandatory
3.5.21 acl-profile set entry action cos
Description Set ACL entry action is mark CoS number. Syntax acl-profileset entryaction cos Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory Valid values: 0~7Type: Mandatory
3.5.22 acl-profile set entry action copyframe
Description Set ACL entry action is copy frame. Syntax acl-profileset entryaction copyframe Parameter Name Description Valid values: 2~10Type: Mandatory Valid values: 1~16Type: Mandatory
3.6.1 scheduler-profile method {spq|spq-wrr|wrr}
Description Set scheduler profile method. Syntax scheduler-profilemethod {spq|spq-wrr|wrr} Parameter Name Description Scheduler profile index. Valid values: 2~8 Type: Mandatory sp|sp-wrr|wrr sp: strict priority sp-wrr: strict priority + weighted round robin wrr: weighted round robin Type: Mandatory
3.6.2 scheduler-profile queue weight
Description Set scheduler profile queue weight. Syntax scheduler-profile<prof-number> queue<queue-number> weight<number> Parameter Name Description Valid values: 2~8Type: Mandatory Valid values: 0~7Type: Mandatory Valid values: 1~255Type: Mandatory
3.7.1 snmp notify
Description Configure snmp notify Syntax snmpnotify Parameter Name Description Index. Valid values: 1~32 Type: Mandatory notify Configure snmp notify Type: Mandatory Notify name Valid values: 1 ~ 31 characters Type: Mandatory
3.7.2 snmp notify delete
Description Configure snmp notify Syntax snmpnotify Parameter Name Description Index. Valid values: 1~32 Type: Mandatory notify Configure snmp notify Type: Mandatory delete Delete a snmp target Type: Mandatory
3.7.3 snmp target
Description Configure snmp target Syntax snmptarget Parameter Name Description Scheduler profile index. Valid values: 1~32 Type: Mandatory target Configure snmp target Type: Mandatory Target IP address Type: Mandatory
3.7.4 snmp target delete
Description Delete a snmp target Syntax snmptarget Parameter Name Description Scheduler profile index. Valid values: 1~32 Type: Mandatory target Configure snmp target Type: Mandatory delete Delete a snmp target Type: Mandatory
Description Config snmp community Syntax snmp communitygroup Parameter Name Description Community name. Valid values: 1 ~ 31 characters Type: Mandatory group Config a community to bind with a group Type: Mandatory Group name Valid values: (1 ~ 15 characters) (input 'none' to unbind) Type: Mandatory
Description Config snmp community Syntax snmp communityro Parameter Name Description Community name. Valid values: 1 ~ 31 characters Type: Mandatory ro Config a community access right as read-only Type: Mandatory
Description Config snmp community Syntax snmp communityrw Parameter Name Description Community name. Valid values: 1 ~ 31 characters Type: Mandatory rw Config a community access right as read-write Type: Mandatory
Description Config snmp community Syntax snmp communityview Parameter Name Description Community name. Valid values: 1 ~ 31 characters Type: Mandatory view Config a community to bind with a group Type: Mandatory Group name Valid values: (1 ~ 15 characters) (input 'none' to unbind) Type: Mandatory
3.7.9 snmp create-community {ro | rw} {view | group}
Description Create snmp community Syntax snmp create-community {ro | rw} {view | group} Parameter Name Description ro Create a snmp community (read only)Type: Mandatory rw Create a snmp community (read,write)Type: Mandatory Community nameValid values: 1 ~ 31 charactersType: Mandatory view Create a snmp community (read only) and bind it with a viewType: Mandatory group Create a snmp community (read only) and bind it with a groupType: Mandatory Group nameValid values: 1 ~ 15 charactersType: Mandatory
3.7.10 snmp create-group model {v1 | v2 | v3sum} level {auth | noauth | priv} read write
Description Create snmp v3 access group Syntax snmp create-groupmodel {v1 | v2 | v3sum} level {auth | noauth | priv} readwrite Parameter Name Description Group nameValid values: 1 ~ 15 charactersType: Mandatory model Security model of the group (v1/v2c/v3)Type: Mandatory v1 SNMP v1 security model v2c SNMP v2c security model v3usm SNMP v3 security model level Security level of the group (noauth/auth/priv)Type: Mandatory auth Authentication, but no privacy noauth No authentication, no privacy priv Both authentication and privacy read Specify a read view to this group View nameValid values: 1 ~ 15 charactersType: Mandatory write Specify a write view to this group View nameValid values: 1 ~ 15 charactersType: Mandatory
3.7.11 snmp create-user {access | group} {ro | rw} {md5 | sha} des
Description Create snmp v3 user Syntax snmp create-user{access | group} {ro | rw} {md5 | sha}des Parameter Name Description User nameValid values: 1 ~ 31 charactersType: Mandatory access Access right of user (ro/rw)Type: Mandatory group Bind user to a groupType: Mandatory ro Read-only user rw Read-write user md5 Use MD5 as authentication protocol sha Use SHA as authentication protocol Authentication pass phraseValid values: 8 ~ 15 charactersType: Mandatory des Use DES as encryption protocol Encryption pass phraseValid values: 8 ~ 15 charactersType: Mandatory
3.7.12 snmp create-view type { exclude | include} subtree
Description Create snmp v3 access view Syntax snmp create-viewtype { exclude | include} subtree Parameter Name Description View nameValid values: 1 ~ 15 charactersType: Mandatory type View type of the subtreeType: Mandatory exclude Exclude the subtree include Include the subtree subtree Set subtree(oid or name) of a viewType: Mandatory Subtree, oid or nameValid values: 1 ~ 31 charactersType: Mandatory
Description Delete snmp community Syntax snmp delete-community name Parameter Name Description name Delete snmp communityType: Mandatory
3.7.14 snmp delete-group
Description Delete snmp v3 group Syntax snmp delete-group name Parameter Name Description name Delete snmp v3 groupType: Mandatory
3.7.15 snmp delete-user name
Description Delete snmp v3 user Syntax snmp delete-user name Parameter Name Description name Delete snmp v3 userType: Mandatory
3.7.16 snmp delete-view { index | name }
Description Delete snmp v3 access view Syntax snmp delete-view { index | name } Parameter Name Description index Delete snmp v3 viewType: Mandatory name Delete snmp v3 viewType: Mandatory
3.7.17 snmp version { v2c | v3 }
Description Config snmp version (v2c/v3) Syntax snmp version { v2c | v3 } Parameter Name Description v2c Set snmp version to v2c v3 Set snmp version to v3
3.8 Interface VLAN Mode Commands
3.8.1 igmp vlan {create|delete}
Description Create / Delete IGMP. Syntax igmp vlan createigmp vlan delete Parameter None
3.8.2 igmp router-port
Description Set IGMP VLAN source port. Syntax igmp router-port Parameter Name Description Valid values: 1~28.Type: Mandatory
3.8.3 igmp access-mode {snooping|proxy}
Description Set IGMP VLAN access mode. Syntax igmp access-mode snoopingigmp access-mode proxy Parameter None
3.8.4 igmp leave-mode {normal|fast}
Description Set IGMP VLAN leave mode. Syntax igmp leave-mode normaligmp leave-mode fast Parameter None
3.8.5 igmp version {v2|v3|v3compatible}
Description Set IGMP VLAN version. Syntax igmp version v2igmp version v3igmp version v3compatible Parameter None
3.8.6 igmp robustness
Description Set IGMP VLAN robustness. Syntax igmp robustness Parameter Name Description Valid values: 1~3.Type: Mandatory
3.8.7 igmp query-interval
Description Set IGMP VLAN query interval. Syntax igmp query-interval Parameter Name Description Valid values: 1~1800 (unit: sec).Type: Mandatory
3.8.8 igmp max-response-time
Description Set IGMP VLAN max response time. Syntax igmp max-response-time Parameter Name Description Valid values: 1~255 (unit: 100ms).Type: Mandatory
3.8.9 igmp last-member-query-count
Description Set IGMP VLAN last member query count. Syntax igmp last-member-query-count Parameter Name Description Valid values: 1~3.Type: Mandatory
3.8.10 igmp last-member-query-interval
Description Set IGMP VLAN last member query interval. Syntax igmp last-member-query-interval Parameter Name Description Valid values: 1~255 (unit: 100ms).Type: Mandatory
3.8.11 igmp vlan interface address
Description Set IP address of IGMP VLAN interface. Syntax igmp vlan interface address Parameter Name Description Valid values: 0.0.0.0~223.255.255.255.Type: Mandatory
3.8.12 ip-address
Description Set layer3 IP address for specified VLAN. Syntax ip-address Parameter Name Description IP address. Valid values: 0.0.0.0~255.255.255.255Type: Mandatory
3.8.13 ip-address netmask
Description Set layer3 IP address and netmask for specified VLAN. Syntax ip-address<ip>netmask Parameter Name Description IP address. Valid values: 0.0.0.0~255.255.255.255Type: Mandatory IP address. Valid values: 0.0.0.0~255.255.255.255Type: Mandatory
3.8.14 igmp version {v2|v3| v3compatible}
Description Set IGMP version. Syntax igmp version {v2|v3| v3compatible} Parameter None
3.9 Ring Group Mode Commands
3.9.1 ringv2-group
Description Ringv2 group interface Syntax ringv2-group Parameter Name Description Ring group indexValid values: 1 ~ 3Type: Mandatory
3.9.2 guardtimer
Description Set guardtimer Syntax guardtimer Parameter Name Description Second. Range: Default is 10 secondsValid values: 10~3600Type: Mandatory
3.9.3 mode enable
Description Enable ring protect on specific ring group Syntax mode enable Parameter None
3.9.4 mode disable
Description Disable ring protect on specific ring group Syntax mode disable Parameter None
3.9.5 node1
Description Ring node1 setting Syntax node1 Parameter Name Description Port numberValid values: 1 ~ 28Type: Mandatory
3.9.6 node2
Description Ring node2 setting Syntax node2 Parameter Name Description Port numberValid values: 1 ~ 28Type: Mandatory
3.9.7 role ring-master
Description Configure the role of ring group as Master of the Ring Syntax role ring-master Parameter None
3.9.8 role ring-slave
Description Configure the role of ring group as Slave of the Ring Syntax role ring-slave Parameter None
3.9.9 role coupling-primary
Description Configure the role of ring group as Primary of the Coupling Syntax role coupling-primary Parameter None
3.9.10 role coupling-backup
Description Configure the role of ring group as Backup of the Coupling Syntax role coupling-backup Parameter None
3.9.11 role dual-homing
Description Configure the role of ring group as Dual Homing Syntax role dual-homing Parameter None
3.9.12 role chain-head
Description Configure the role of ring group as Head of the Chain Syntax role chain-head Parameter None
3.9.13 role chain-tail
Description Configure the role of ring group as Tail of the Chain Syntax role chain-tail Parameter None
3.9.14 role chain-member
Description Configure the role of ring group as Member of the Chain Syntax role chain-member Parameter None
3.9.15 role balancing-chain-terminal-1
Description Configure the role of ring group as Terminal 1 of the Balancing Chain Syntax role balancing-chain-terminal-1 Parameter None
3.9.16 role balancing-chain-terminal-2
Description Configure the role of ring group as Terminal 2 of the Balancing Chain Syntax role balancing-chain-terminal-2 Parameter None
3.9.17 role balancing-chain-member
Description Configure the role of ring group as Member of the Balancing Chain Syntax role balancing-chain-member Parameter None
3.9.18 role balancing-chain-central-block
Description Configure the role of ring group as Central Block of the Balancing Chain Syntax role balancing-chain-central-block Parameter None
3.10 IGMP MVR Mode Commands
3.10.1 igmp-mvr {create|delete}
Description Create / delete IGMP MVR profile. Syntax igmp-mvr <number,2..15> {create|delete} Parameter Name Description IGMP MVR profile index. Valid values: 2~15 Type: Mandatory
3.10.2 igmp-mvr entry
Description Create IGMP MVR entry. Syntax igmp-mvrentry Parameter Name Description IGMP MVR profile index. Valid values: 2~15 Type: Mandatory IGMP MVR entry index. Valid values: 1~32 Type: Mandatory IP address. Valid values: 224.0.1.0~239.255.255.255 Type: Mandatory VLAN ID. Valid values: 1~4094 Type: Mandatory
3.10.3 igmp-mvr entry delete
Description Delete IGMP MVR entry. Syntax igmp-mvrentrydelete Parameter Name Description IGMP MVR profile index. Valid values: 2~15 Type: Mandatory IGMP MVR entry index. Valid values: 1~32 Type: Mandatory
3.11 IGMP ACL Mode Commands
3.11.1 igmp-acl {create|delete}
Description Create / delete IGMP ACL profile. Syntax igmp-acl {create|delete} Parameter Name Description IGMP ACL profile index. Valid values: 2~15 Type: Mandatory
3.11.2 igmp-acl {default-deny| default-permit}
Description Set IGMP ACL default rule. Syntax igmp-acl{default-deny| default-permit} Parameter Name Description IGMP ACL profile index. Valid values: 2~15 Type: Mandatory
3.11.3 igmp-acl entry {|all} {permit|
Description Create IGMP ACL entry. Syntax igmp-aclentry{}{permit|deny} Parameter Name Description IGMP ACL profile index. Valid values: 2~15 Type: Mandatory IGMP MVR entry index. Valid values: 1~32 Type: Mandatory IP address. Valid values: 224.0.1.0~239.255.255.255 Type: Mandatory VLAN ID. Valid values: 1~4094 Type: Mandatory
3.11.4 igmp-acl entry delete
Description Delete IGMP ACL entry Syntax igmp-aclentrydelete Parameter Name Description IGMP ACL profile index. Valid values: 2~15 Type: Mandatory IGMP MVR entry index. Valid values: 1~32 Type: Mandatory
3.12 Trunk Group Mode Commands
3.12.1 trunk enable static
Description Enable link aggregation group and its mode is static. Syntax trunk enable static Parameter None
3.12.2 trunk disable
Description Disable link aggregation group and all member port will be remove on specific port. Syntax trunk disable Parameter None
3.12.3 port-trunk add
Description Add member port to specific trunk group, the max member ports is 4. Syntax port-trunk add Parameter Port number. Valid values: 1~28 Type: Mandatory
3.12.4 port-trunk remove {|all}
Description Remove member port from specific trunk group. Syntax port-trunk remove Parameter Port number. Valid values: 1~28 Type: Mandatory all All member port. Type: Mandatory
3.13.1 show profile alarm
Description Show alarm profile list Syntax show profile alarm Parameter None
3.13.2 show alarm current
Description Show current alarm list Syntax show alarm current Parameter None
3.13.3 show event
Description Show event list Syntax show event (Refer to. event Table) Parameter None
3.13.4 show alarm history
Description Show alarm history Syntax show alarm history Parameter None
3.13.5 event clear
Description Clear event. Syntax event clear Parameter None
3.13.6 alarm history clear
Description Clear alarm history. Syntax alarm history clear. Parameter None
3.13.7 profile alarm
Description Enter Alarm Profile Configuration Mode. Syntax profile alarm Parameter None
3.13.8 alarm {mask|unmask|major|minor}
Description Configure an alarm profile entry (default setting for each alarm is unmask and minor) Syntax alarmmaskalarmunmaskalarmmajoralarmminor Parameter Name Description Alarm IDValid values: Refer to. Alarm TableType: Mandatory mask Mask this alarmType: Mandatory unmask Unmask this alarmType: Mandatory major Set alarm level to majorType: Mandatory minor Set alarm level to minorType: Mandatory
