HD 5/11 X Plus Classic - Pressure washer Kärcher - Free user manual and instructions

Type of product	High-pressure cleaner
Brand	Kärcher
Model	HD 5/11 X Plus Classic
Dimensions (L x W x H)	350 x 330 x 880 mm
Weight (without accessories)	21 kg
Power supply	220-240 V, 50 Hz, 2.2 kW
Main fuse (slow)	15 A
Protection	IPX5
Operating pressure	11 MPa (110 bar)
Max. overpressure	16 MPa (160 bar)
Water flow rate	500 l/h (8.4 l/min)
Max. feed pressure	1.0 MPa (10 bar)
Max. feed temperature	40 °C
Min. feed flow rate	720 l/h (12 l/min)
Standard nozzle	036
Sound pressure level LpA	76 dB(A)
Sound power level LWA	91 dB(A)
Hand-arm vibration	2.27 m/s²
Main functions	High-pressure jet, detergent operation (foam lance optional), rotating lance (on X Plus model), integrated hose reel
Safety	Safety lever on gun, overflow valve, safety lock, electrical shock protection
Maintenance	Weekly cleaning of water filter, oil change every 500 h (by after-sales service), frost protection
Spare parts and repairability	Use only original Kärcher accessories; spare parts available at www.kaercher.com; repairs by authorized service
General information	Intended use: cleaning of machines, vehicles, facades, terraces; warranty according to country conditions; weight 21 kg, transport by telescopic handle

Frequently Asked Questions - HD 5/11 X Plus Classic Kärcher

How to start the high-pressure cleaner for the first time?

Before first use, unpack the device, install the push handle and the nozzle. Connect the high-pressure hose, power cable and water supply. Bleed the device by removing the nozzle, turn on and let water flow until no more air bubbles, then turn off and reinstall the nozzle.

What are the essential safety precautions?

Never direct the jet towards people, animals, electrical equipment or the device itself. Wear personal protective equipment (hearing protection). Use a system separator compliant with EN 12729 type BA for connection to the drinking water network. Follow the provided safety instructions.

How to use detergent with this device?

An optional foam lance is required. Pour the detergent into the lance container, spray sparingly on the dry surface, let it act without drying, then rinse with high-pressure jet. After use, rinse the lance with clean water for 30 seconds.

What to do if the pressure is insufficient?

Check that the standard nozzle (size 036) is installed and not clogged. Bleed the device (remove nozzle, turn on until flow without bubbles). Clean the water filter. Check the feed flow rate (min. 720 l/h). If the problem persists, contact after-sales service.

How to store the device in winter to prevent freezing?

Frost-free storage recommended. Otherwise, drain the water: close water supply, open the gun to release pressure, then pump glycol-based antifreeze into the device by running it for max. 1 minute. Follow the antifreeze manufacturer's instructions.

What is the maintenance frequency of the water filter?

The water filter should be cleaned every week. Remove the filter, clean it under running water, check that it is not damaged before reinstalling.

How to replace the high-pressure nozzle?

Turn off the device and operate the gun to release pressure. Push the safety lever forward to lock. Unscrew the nozzle screws, remove the old nozzle, install the new one and tighten the screws. For the X Plus model, the rotating lance screws onto the yellow connector.

What to do in case of water leakage at the pump?

Up to 3 drops per minute are acceptable. If the leak is larger, have the device checked by an authorized after-sales service.

What optional accessories are available?

Kärcher offers accessories such as the foam lance, sandblaster for stubborn dirt, and other nozzles. Use only original accessories to ensure safety and proper operation.

How to safely transport the device?

Place the lance with the gun on the hooks, wrap the cable around the cable hooks and the high-pressure hose (on the reel if present). For short distances, use the telescopic handle. To go up stairs, hold the additional handle and lift. Secure the device in a vehicle to prevent movement.

USER MANUAL HD 5/11 X Plus Classic Kärcher

Deutsch 6 English 11 Français 17 Italiano 22 Español 28 Português 33 Nederlands 39 Türkçe 44 Svenska 49 Suomi 55 Norsk 60 Dansk 65 Eesti 70 Latviešu 75 Lietuviškai 80 Polski 86 Ελληνικά 129

Magyar 91

Čeština 97

Slovenčina 102

Slovenščina 108

Românește 113

Hrvatski 119

Srpski 124

Русский 135

Українська 141

Български 147

Việt 153

Bahasa Melayu 158

Indonesia 164

A

B

Contents

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.01.2019

Contents

General notes.... 11

Intended use.... 11

Environmental protection.... 12

Accessories and spare parts 12

Scope of delivery.... 12

Safety instructions 12

Safety devices 12

Symbols on the device 12

Description of the device 12

Initial startup 13

Operation 13

Transportation 14

Storage 14

Care and service 14

Troubleshooting guide 15

Warranty 15

Technical data 15

EU Declaration of Conformity 16

General notes

Read these original operating instructions and the enclosed safety instructions before using the device for the first time.

time. Proceed accordingly.

Keep both books for future reference or for future owners.

Intended use

The high-pressure cleaner with high-pressure jet is intended only for the cleaning of objects, including:

- Machines, vehicles, structures, tools, facades, terraces and garden equipment.

Detergent can be added with optional accessories. We recommend using a dirt blaster as a special accessory for stubborn soiling.

Water supply limit values

ATTENTION

Dirty water

Premature wear and tear or deposits in the device. Supply the device using only clean water, or recycled water that does not exceed the specified limit values.

The following limit values apply to the water supply:

• pH value: 6.5-9.5
• Electrical conductivity: Conductivity of fresh water + 1200 μS/cm, maximum conductivity 2000 μS/cm
• Settleable particles (sample volume 1 l, settling time 30 minutes): < 0.5 mg/l
• Filterable particles: < 50 mg/l, no abrasive substances • Hydrocarbons: < 20 mg/l
• Chloride: < 300 mg/l
• Sulphate: < 240 mg/l • Calcium: < 200 mg/l
• Total hardness: < 28 °dH, < 50 °TH, < 500 ppm (mg CaCO3/l)
• Iron: < 0.5 mg/l
• Manganese: < 0.05 mg/l • Copper: < 2 mg/l • Active chloride: < 0.3 mg/l • Free of unpleasant odours

Environmental protection

The packing materials can be recycled. Please dispose of packaging in accordance with the environmental regulations.

Electrical and electronic devices contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential danger to human health and the environment. However, these components are required for the correct operation of the device. Devices marked by this symbol are not allowed to be disposed of together with the household rubbish.

Notes on the content materials (REACH)

Current information on content materials can be found at: www.kaercher.de/REACH

Accessories and spare parts

Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely.

Information on accessories and spare parts can be found at www.kaercher.com.

Scope of delivery

Check the contents for completeness when unpacking. If any accessories are missing or in the event of any shipping damage, please notify your dealer.

Safety instructions

• It is essential that you read the safety instructions 5.951-949.0 before initial start-up.
• Observe the national regulations for liquid jet cleaners.
• Observe the national accident prevention regulations. Liquid jet cleaners must be tested regularly. The test result must be recorded in writing.
• Do not modify the device or accessories.

Safety devices

△CAUTION

Missing or modified safety devices

Safety devices are provided for your own protection. Never modify or bypass safety devices.

Safety lever

The safety lever on the high-pressure gun prevents the device from being switched on inadvertently.

Overflow valve

If the high-pressure gun is closed, the overflow valve opens and the entire water volume will flow back to the pump suction side.

The overflow valve is set by the manufacturer and sealed. Setting shall only be carried out by Customer Service.

Symbols on the device

Do not aim the high-pressure jet at persons, animals, live electrical equipment or the device itself.

Protect the device against frost.

According to applicable regulations, the device must never be used with the drinking water network without a system separator. Ensure that the connection to your house water system, with which the high-pressure cleaner is operated, is equipped with a system separator according to EN 12729 type BA. Water that has flowed through a system separator is classified as undrinkable. Always connect the system separator to the water inlet and never directly to the device.

⚠ WARNING

The high nozzle outlet speed of the high-pressure water jet results in a high noise level that can cause discomfort or hearing damage (e.g. tinnitus) to persons in the immediate vicinity. A continuously high noise level can result in deafness.

• Wear the prescribed personal protective equipment.
• High noise levels can impair vocal communication and impair or prevent your ability to perceive acoustic warning signals. Never work alone. A second person must be present outside the work area.

Description of the device

Overview of HD 5/11 E Classic

Illustration A

① Nozzle screws ② High-pressure nozzle ③ Spray lance ④ Safety lock ⑤ Gun handle

⑥ Trigger

⑦ High-pressure hose

⑧ Gun hook

⑨ Additional handle

⑩ Cable hook

⑪ Water filter

⑫ Spray lance storage quiver (for long spray lance)

⑬ Water inlet connection

⑭ Water outlet

⑮ Power switch

⑯ Push handle, top (extended)

Overview of HD 5/11 EX Plus Classic

Illustration B

① Nozzle screws ② High-pressure nozzle ③ Spray lance ④ Safety lock ⑤ Gun handle

⑥ Trigger ⑦ High-pressure hose ⑧ Push handle, top (extended) ⑨ Additional handle ⑩ Cable hook ⑪ Water filter ⑫ Spray lance storage quiver (for long spray lance) ⑬ Water inlet connection ⑭ Water outlet ⑮ Power switch ⑯ Hand crank ⑰ Spray lance holder ⑱ Dirt Blaster

Initial startup

⚠️ DANGER

Danger of injury from electric shock

Only allow authorised technical specialists to install the water supply, electrical connections and high-pressure network.

Colour coding

- Control elements for the cleaning process are yellow.

Unpacking

1. Check the contents of the package when unpacking.
2. Notify the dealer immediately in the case of shipping damage.

Installing the accessories

1. Insert the push handle into the machine and insert the screws into the handle. Illustration C
2. Install the nozzle with the nozzle screws at the spray lance.
3. Connect the spray lance to the high-pressure gun. Illustration D
4. Screw the high-pressure hose to the high-pressure gun.
5. Only HD 5/11 E Classic: Fasten the high-pressure hose to the water outlet.
6. Only HD 5/11 EX Plus Classic: Push the hand crank into the hole of the hose reel and make sure the hand crank is secure.

Illustration E

Electrical connection

⚠️DANGER

Risk of injury from electric shock

Use a plug to connect the device to the mains grid. Permanent connection to the mains grid is prohibited. The plug is used for disconnection from the mains.

See the type plate or technical data for the connection values.

1. Unwind the mains cable and place it on the ground.
2. Plug the mains plug into the socket.

Water connection

Connection to a water line

⚠ WARNING

Health risk from return flow of contaminated water into the drinking water network.

Observe the regulations of your water supply company.

1. Check the feed pressure, input temperature and input amount of the water supply. See Chapter Technical data for the requirements.
2. Connect the system separator and water connection of the device with a hose (minimum length 7.5 m, minimum diameter 3/4").

The supply hose is not included in the scope of delivery.

1. Open the water inlet.

Venting the device

1. Open the water inlet.
2. Remove the high-pressure nozzle.
3. Switch on the device.
4. Allow the device to run until the escaping water is free of air bubbles.
5. Switch off the device.
6. Fit the high-pressure nozzle.

Operation

⚠️DANGER

Risk of explosion!

Do not spray flammable liquids.

If the device is used in hazardous areas (e.g. filling stations), the corresponding safety regulations must be observed.

Opening / closing the high-pressure gun

1. Push back the safety lock and actuate the trigger. Illustration F

The high-pressure gun opens.

1. Release the trigger and push the safety lock forward.

Then the high-pressure gun closes.

High-pressure operation

Note

• The device can be operated vertically.
• The device is equipped with a pressure switch. The motor only starts up when the high-pressure gun is open.
• The high-pressure hose should be kept away from sharp edges.
• For a device with the hose reel: unfold the high-pressure hose completely from the hose reel.
• Open the water supply.
• Set the power switch to "1".
• Open the safety lock of the high-pressure gun.
• Open the high-pressure gun.
• Aim the high-pressure gun at the object to be cleaned and start the cleaning operation.

Operation with detergent

Note

A foam lance (optional) is needed for operating with detergent.

⚠ WARNING

Incorrect handling of detergents

Health risk

Adhere to the safety instructions stated on the detergent packaging.

ATTENTION

Unsuitable detergents

Damage to the device and the objects to be cleaned Use only detergents approved by KÄRCHER.

Observe the dosing recommendations and notes provided with the detergent.

Use detergents sparingly to help conserve the environment.

KÄRCHER detergents ensure fault-free operation.

Please feel free to request a consultation, our catalogue or our detergent information sheets.

1. Fill the detergent into the container of the foam lance. (Follow the dosage instructions on the detergent bottle.) Illustration G

Recommended cleaning method

1. Spray the detergent sparingly on the dry surface and let it work for a while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.

After operation with detergent

1. Flush the foam lance with clear water for approx. 30 seconds.

Replacing the nozzle

⚠️ DANGER

Risk of injury!

Switch the device off prior to replacing nozzle and do not activate hand spray gun until the device is pressure-less.

1 Secure the high-pressure gun. To do so, push the safety lever towards the front. 2 Unscrew nozzle screws and remove the nozzle. 3 Put on a new nozzle. 4 Only HD 5/11 EX Plus Classic: Screw on the dirt blaster and tighten them by hand.

Dirt Blaster Storage

1. Screw the dirt blaster onto the yellow connector. Illustration H

Interrupting operation

Note

When the device is shut down, the water pressure will be reduced, which can reduce the operating force of the high-pressure gun and improve the service life of the equipment.

1. Close the high-pressure gun, the device will interrupt.
2. Push the safety lock forward to close the safety lock of the high-pressure gun.
3. Push the safety lock back to open the safety lock of the high-pressure gun.
4. Open the high-pressure gun, the device will switch on again.

Finishing operation

1. Shut off the water supply.
2. Open the high-pressure gun.
3. Set the power switch to "1" and let the device run for 5 to 10 seconds.
4. Set the power switch to "0".
5. Close the high-pressure gun.
6. Unplug the power supply from the device with dry hands.
7. Remove water inlet.
8. Close the safety lever of the high-pressure gun and push the safety lock forward.

Transportation

⚠CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transportation.

1. Place the spray lance with the high-pressure gun on the hooks.
2. Wind the power cable around the cable hooks.
3. Without hose reel: Wind up the high-pressure hose and hang it over the hook. With hose reel: Wind the high-pressure hose onto the hose reel.
4. When transporting the device in vehicles, secure the device against shifting and tipping over.
5. For short distance transportation, pull the telescopic handle to drag the device. Illustration I
6. When going up stairs, hold the additional handle and lift the device up. Illustration J

Storage

△CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

Store the device indoors only.

Frost protection

ATTENTION

Frost destroys the device if it is not completely drained of water.

Store the device in a frost-free location.

If frost-free storage is not possible:

1. Drain excess water.
2. Pump commonly available anti-freeze through the device.
3. Allow the device to run for a maximum of 1 minute until the pump and lines are empty.

Note

Use commonly available, Glycol-based vehicle anti-freeze. Observe the handling instructions of the anti-freeze manufacturer.

Care and service

⚠️DANGER

Inadvertently starting up the device

Risk of injury, electric shock

Switch off the device immediately and unplug the mains plug before performing work.

Note

Old oil may only be disposed of at designated collection points. Please dispose of any old oil at these locations. Polluting the environment with old oil is punishable by law.

Safety inspection/maintenance contract

You can agree on regular safety inspections or close a maintenance contract with your dealer. Please seek advice on this.

Maintenance intervals

Each time before use

1. Check the power cable for damage and have a damaged cable replaced immediately by the authorised Customer Service or a qualified electrician.
2. Check the high-pressure hose for damage and replace a damaged high-pressure hose immediately.
3. Check the device for leaks. 3 drops of water per minute are permissible. Contact Customer Service in the case of more serious leaks.

Weekly

1. Clean the water filter, see Chapter Cleaning the water filter.

Every 500 operating hours, at least once annually

Have the oil changed by Customer Service.

Maintenance work

Cleaning the water filter

Check the water filter for damage before inserting it into the water connection.

1. Pull the water filter out.
2. Clean the water filter under running water.
3. Re-insert the water filter into the water connection.

Troubleshooting guide

⚠️ DANGER

Risk of injury due to inadvertently starting up device and also due to electric shock.

Switch off the device immediately and unplug the mains plug before performing work.

Have electrical components checked and repaired by the authorised Customer Service.

In case of any malfunctions not mentioned in this chapter, contact the authorised Customer Service when in doubt or when you have been explicitly advised to do so.

ATTENTION

Damaged water filter in the water connection

Damage to the device through contaminated water

Fault Remedy
Device does not start	Check the power cable for damage.Check the mains voltage.If the device overheats:a Set the power switch to "0".b Allow the device to cool for at least 15 minutes.c Set the power switch to "1".Contact Customer Service in case of electrical faults.
Device not building up pressure	Fit the standard nozzle (size specified, see Chapter Technical data).Clean / replace the high-pressure nozzle.Vent the device (see Chapter Venting the device).Clean the water filter (see Chapter Cleaning the water filter).Clean all inlet pipes to the pump.Check the water supply volume (see Chapter Technical data).
Pump leakingUp to 3 drops of water per minute are permissible.	In case of more serious leaks, have the device checked by Customer Service.
Pump knocking Clean	the water filter.Check the water supply line for leaks.Vent the device (see Chapter Venting the device).Contact Customer Service if necessary.

Warranty

The warranty conditions issued by our sales company responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

turing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.

Technical data

Subject to technical modifications.

		HD 5/11 E Classic HD 5/11 EX Plus Classic
Electrical connection
Voltage V 220 - 240 220 - 240
Phase	~	1	1
Frequency	Hz	50	50
Power rating	kW	2.2	2.2
Degree of protection		IPX5	IPX5
Power protection (slow-blowing)	A 15		15
Extension cable, 30 m	mm 2	2.5HD 5/11 E Classic	2.5HD 5/11 EX Plus Classic
Water connection
Feed pressure (max.) MPa (bar) 1.0 (10) 1.0 (10)
Input temperature (max.) °C 40 40
Input amount (min.) l/h (l/min) 720(10) 720 (12)
Suction height (max.) m 1.0 1.0
Device performance data
Nozzle size of standard nozzle 036	036
Water flow rate	l/h (l/min) 500 (8.4)		500 (8.4)
Operating pressure	MPa (bar) 11 (110)		11 (110)
Operating pressure (max.)	MPa (bar) 16 (160)		16 (160)
High-pressure gun recoil force	N	20.4	20.4
Dimensions and weights
Weight (without accessories)	kg	18 21
Length x width x height	mm	350 x 330 x 880	350 x 330 x 880
Determined values in acc. with EN 60335-2-79
High-pressure gun hand-arm vibration value	m/s 2	2.27	2.27
Uncertainty K	m/s 2	1.5 1.5
Sound pressure level L pA	dB(A)	76 76
Uncertainty K pA	dB(A)	2.5 2.5
Sound power level L WA + uncertainty K WA	dB(A)	91 91

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

We hereby declare that the machine described below complies with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version placed on the market by us. This declaration becomes invalid if any modifications are made to the machine without our approval.

Type: 1.520-xxx

Type: 1.520-xxx

Currently applicable EU Directives

2000/14/EC

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Harmonised standards used

EN 60335-1

EN 60335-2-79

EN 55012: 2007 + A1: 2009

EN IEC 63000:2018

EN 62233: 2008

Applied conformity evaluation method

2000/14/EG: Annex V

Sound power level dB(A)

HD 5/11 E Classic

Measured: 89.8

Guaranteed: 92

HD 5/11 EX Plus Classic

Measured: 91.3

Guaranteed: 93

The undersigned act on behalf and under the power of attorney of the company management.

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Fax: [phone]

Winnenden, 2019/01/01

Content

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Winnenden, 01/01/2019

Index

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01/01/2019

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2019/01/01

Index

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2019/01/01

Table of Contents

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Winnenden, 2019/01/01

Contents

General information 49

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

D-71364 Winnenden (Germany)

Phone: [phone]

Fax: [phone]

Winnenden, 2019-01-01

Contents

General instructions 55

Intended use 55

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Phone: [phone]

2006/42/EF (+2009/127/EF)

2011/65/EU

2014/30/EU

Harmonised standards used

EN 60335-1

EN 60335-2-79

EN 55012: 2007 + A1: 2009

EN IEC 63000:2018

EN 62233: 2008

Applied conformity assessment method

2000/14/EU: Annex V

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 01/01/2019

Contents

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2019/01/01

Contents

General instructions 70

Intended use 70

Environmental protection 70

Accessories and spare parts.... 70

Scope of delivery 70

Safety instructions 70

Safety devices 71

Product: High-pressure washer

Type: 1.520-xxx

2006/42/EU (+2009/127/EU)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel: [phone]

Winnenden, 2019/01/01

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

2006/42/WE (+2009/127/WE)

2011/65/UE

2014/30/UE

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

H. Jenner, Chairman of the Board of Management

S. Reiser, Director Regulatory Affairs & Certification

2006/42/ES (+2009/127/ES)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Winnenden, 2019/01/01

Table of Contents

General notes.... 102

2006/42/ES (+2009/127/ES)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 2019/01/01

Table of Contents

General instructions.... 108

Intended use.... 108

Environmental protection 108

Accessories and spare parts.... 108

Scope of delivery.... 108

Safety instructions.... 108

Safety devices 108

Symbols on the device.... 108

Description of the device.... 109

First start-up 109

Operation 110

Transport and carriage.... 110

Storage 111

Care and service 111

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

Winnenden, 1. 1. 2019

Table of contents

Relevant EU directives

2000/14/EC

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Harmonized standards used

EN 60335-1

EN 60335-2-79

EN 55012: 2007 + A1: 2009

EN IEC 63000:2018

EN 62233: 2008

Applied conformity evaluation method

2000/14/EC: Annex V

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Table of contents

General notes.... 119

Intended use 119

Environmental protection 119

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Authorized representative for documentation:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 1.1.2019.

Contents

General notes.... 124

Intended use.... 124

2006/42/EC (+2009/127/EC)

2011/65/EU

2014/30/EU

Harmonized standards used

EN 60335-1

EN 60335-2-79

EN 55012: 2007 + A1: 2009

EN IEC 63000:2018

EN 62233: 2008

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Person authorized to compile the documentation:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Tel.: [phone]

Winnenden, 1. 1. 2019.

Contents

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01/01/2019

Table of Contents

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

71364 Winnenden (Germany)

Tel.: [phone]

Fax: [phone]

Winnenden, 01.01.2019

Table of Contents

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Winnenden, 01/01/2019

Table of Contents

General Note 158

Chairman of the Board of Management

S. Reiser

Director Regulatory Affairs & Certification

Documentation supervisor:

S. Reiser

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28 - 40

71364 Winnenden (Germany)

Ph.: [phone]

Winnenden, 2019/01/01

Table of Contents

H. Jenner Chairman of the Board of Management

S. Reiser Director Regulatory Affairs & Certification

Winnenden, 01/01/2019

THANK YOU!

THANK YOU! DANKE! GRACIAS!

Register your product and benefit from many advantages.

www.kaercher.com/welcome

Rate your product and tell us your opinion.

www.kaercher.com/dealersearch

Alfred Kärcher SE & Co. KG

Alfred-Kärcher-Str. 28-40

71364 Winnenden (Germany)