Wave Plus M0542 - Speaker Krüger&Matz - Free user manual and instructions

Product Type	2.0 Powered Speaker
Brand	Krüger&Matz
Model	Wave Plus M0542
Output Power	2 x 42 W
Frequency Response	50 Hz - 20 kHz
Signal-to-Noise Ratio	≥ 60 dB
Total Harmonic Distortion	0.1%
Bluetooth	Version 4.0, range up to 10 m
FM Radio	Yes, with antenna
Audio Inputs	RCA (2), coaxial, optical, USB, SD, microphone (2)
Outputs	Speakers (via cable)
Power Supply	220-240 V, 50/60 Hz
Power Consumption	42 W
Speaker Diameters	8 inches (woofer), 4 inches (midrange), 2 inches (tweeter)
Box Contents	Remote control, wireless microphone, power cable, speaker cable
Cleaning	Soft damp cloth, no chemicals
Safety	Do not open, keep away from moisture, unplug before cleaning

Frequently Asked Questions - Wave Plus M0542 Krüger&Matz

What to do if the speaker does not turn on?

Check that the power cord is properly plugged in and that the power switch is set to ON. Make sure the outlet works.

There is no sound, what to check?

Make sure the input and output cables are correctly connected. Check that the volume is not at minimum and that the playback mode is appropriate (Bluetooth, USB, etc.).

Bluetooth cannot find the speaker?

Make sure the speaker is in Bluetooth mode (press Mode until Bluetooth is selected). Place the devices close together. On your phone, search for devices and select 'KM WAVE PLUS'.

How to clean the speaker?

Unplug the device. Use a soft damp cloth (no chemicals). Avoid water getting inside.

Why is the sound distorted at high volume?

Lower the volume. Distortion can occur if the volume is at maximum. If the problem persists, check the equalizer settings.

How to use the FM radio?

Press Mode until FM is selected. Extend the FM antenna. For automatic search, press the SCAN button on the remote control. Use the Previous/Next buttons to navigate.

What to do if USB/SD mode does not work?

Make sure you are in USB or SD mode (press Mode). Reconnect the USB device or SD card. Verify that the file format is supported (usually MP3).

How to adjust the equalizer?

In USB, SD or Bluetooth mode, press the EQ button on the front panel or remote control to choose between presets: Pop, Rock, Jazz, Classical, Club, or Normal.

Can I connect a microphone?

Yes, plug a microphone into the MIC1 or MIC2 inputs on the side panel. Use the Mic Vol and Echo knobs to adjust volume and echo.

How to reset the speaker?

Unplug the speaker from power for a few minutes, then plug it back in. This will reset it to default settings.

USER MANUAL Wave Plus M0542 Krüger&Matz

2.0 active floorstanding speaker set KM0542

BEDIENUNGSANLEITUNG

OWNER'S MANUAL

MODE D'EMPLOI

GEBRUIKSAANWIJZING

INSTRUKCJA OBSŁUGI

MANUAL DE UTILIZARE

Completely black image with no visible content or text.

VOLUME TREBLE BASS MIC. VOL ECHO MIC1 MIC2

RÜCKSEITIGES PANEEL

Read the instruction manual carefully before first use and keep it for future reference.

	CAUTION
	RISK OF ELECTRIC SHOCKDO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user the presence of uninsulated, dangerous voltage, within the product enclosure that may be of sufficient magnitude to constitute risk of electric shock to person.

The exclamation point within an equilateral triangle is intended to alert the user the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance.

1. Make sure to place this product on flat, dry and stable surface.
2. Place the device in a properly ventilated place.

Warning: The device can increase its temperature during operation!

1. Protect this product from moisture, humidity, water and any other liquid. Avoid using/storing it in extreme temperatures. Do not expose it to direct sunlight and sources of heat.
2. The appliance should be connected to a power supply as per specification in the operating instructions or as marked on the appliance.
3. Keep the volume at a reasonable level throughout entire time of using the speakers. To prevent damage to your hearing, do not raise the volume too high.
4. Stop using the speakers if you feel a tinnitus, hearing discomfort, irritation or have other adverse reactions.
5. Disconnect the device from the power supply if it is not going to be used for a long time.
6. Do not attempt to repair this device yourself. In case of damage, contact with an authorized service point for check-up/repair.
7. This appliance may be used by children who are above 8 years old and by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they are supervised and guided by a person who is responsible for their safety in a cautious manner, and all the safety precautions are understood and followed. Children should not play with this device. Children should not perform cleaning and servicing of the device unsupervised.
8. Fixed power cable may only be replaced in an authorized service point.
9. ALWAYS disconnect this device from power supply mains before cleaning.
10. Clean this device with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product.

PRODUCT DESCRIPTION FRONT PANEL

① MODE EQ REPEAT PREV VOL- NEXT VOL+ PLAY PAUSE ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ USB SD ⑩

1. Display.
2. Mode button (Line in, AUX in, USB, SD, Bluetooth, FM radio).
3. EQ (Equalizer): Equalizer settings adjustment in USB, SD and Bluetooth mode (Pop, Rock, Jazz, Classic, Club, Normal).
4. Repeat button: Press this button to repeat one song in USB/SD mode. Press this button again to repeat all songs.
5. Previous/Volume down (Prev/Vol-): Press to go to the previous song in USB/SD/Bluetooth mode. Press to go to the previous radio channel in FM radio mode. Press and hold to decrease volume in all modes.
6. Next/Volume up (Next/Vol+): Press to go to the next song in USB/SD/Bluetooth mode. Press to go to the next radio channel in FM radio mode. Press and hold to increase the volume in all modes.
7. Play/Pause: Press this button to play/pause music playback in USB/SD/Bluetooth mode. Press to mute in AUX/FM radio mode. Press and hold to auto scan FM radio channels in FM radio mode.
8. IR sensor.
9. USB port.
10. SD card slot.

SIDE PANEL

1. Power indicator
2. Volume knob: Adjust the volume
3. Treble knob: Adjust the gain of the treble
4. Bass knob: Adjust the gain of the bass
5. Microphone volume (Mic vol): Adjust the microphone volume
6. Echo knob: Adjust the reverberation
7. Microphone 1/Microphone 2 (Mic1/Mic2): Microphone inputs

VOLUME TREBLE BASS MIC. VOL ECHO MIC1 MIC2

BACK PANEL

1. FM antenna
2. Audio input
3. Coaxial input
4. Optical input
5. Audio output
6. Power switch
7. Power cable

RADIO ANTENNA AUDIO INPUT SPDIF INPUT Coaxial Lock Optical OUTPUT - + Only connect endosec slave unit or contact your supplier WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION DO NOT TOUCH THE RACK SIDE OF THIS SPEAKER Krüger&Matz 2.0 active theatre speakers Model: KM0542 Power: 42 W x2 Made in China for LEON-POL ELECTRONICS sp. 2 n.o. w/x. Mjtrn, st. Garwotinaka 1, 08-493 Garwotn. AC220V-240V,59/60Hz

REMOTE CONTROL

1. Power button.
2. Mute button.
3. Repeat: In USB/SD mode, press this button to repeat one track ("ONE" will be displayed); press again to repeat all tracks ("ALL" will be displayed).

4.

• Previous: Press to go to the previous track in USB/SD/Bluetooth mode. / Channel down (CH-): Press this button to go to the previous FM station.

• Next: Press this button to go to the next track in USB/SD/Bluetooth mode. / Channel up (CH+): Press this button to go to the next station.

• Volume up (VOL+): Press to increase volume. / Volume down (VOL-): Press to decrease volume.

• Play/Pause: Press this button to play/pause music playback in USB/SD/Bluetooth mode.

• Optical / Coaxial Button.

• EQ (Equalizer): EQ (Equalizer): Equalizer settings adjustment in USB, SD and Bluetooth mode (Pop, Rock, Jazz, Classic, Club, Normal).

• Auto search button (SCAN): While in FM mode, press this button to auto search available FM channel.

• MODE button: Press this button to switch between available modes.

• Number key: Use these buttons to select tracks in USB/SD mode. In FM mode, use number buttons to choose the desired channel by typing its frequency.

1 2 3 4 5 6 7 8 9 10 11 VOL+ S VOL- EQ SCAN 0 MODE 1 2 3 4 5 6 7 8 9 Krüger&Matz

INSTALLATION

1. Connect the speakers with the speaker cable.

BLACK RED

1. Connect the external device to the selected input of the speakers with a proper cable.

Notice: Please pay attention to the proper connection of the cables with the inputs.

graph TD
    A["L"] --> B["SPDIF INPUT"]
    C["R"] --> B
    B --> D["Coaxial"]
    B --> E["Optical"]

1. Connect the speaker to the power supply mains with the power cable.
2. Set all knobs to the minimum.
3. Turn on the device by setting the power switch in ON position.
4. Adjust all the knobs.

BLUETOOTH MODE

1. Make sure the speaker is turned on.
2. Please keep the speaker and external device close to each other when pairing.
3. Press Mode button to enter Bluetooth pairing mode.
4. Enable the Bluetooth function on the external device and search for new Bluetooth devices.
5. Select and connect with this device „KM WAVE PLUS“.
6. Start playing music from the external device.

Note:

- Every time the speaker is switched on, it will connect to last connected device automatically. Please note, your device must be on with Bluetooth function turned on.

TROUBLESHOOTING

Problem Possible solution
No power • Check if the power cord is properly connected• Check the position of power switch (it should be set in ON position
No sound • Check if the input and output cables are properly connected
One channel is not working •	Check the audio input and output
Main speaker is not working •	Check the audio input cable
Distorted sound at high volume	• Reduce the volume
USB/SD are not working • Check if the mode is set to USB/SD• Reconnect the USB device/SD card
Poor sound quality of FM radio	• Fully extend the antenna• Adjust the position of antenna• Separate the antenna from other cables or appliances• Turn off TV/DVD or other devices nearby

SPECIFICATION

• Power output: 2x 42 W
• Frequency response: 50 Hz \~ 20 kHz
- Input sensitivity: < 500 mV
• S/N Ratio: ≥ 60 dB
- THD: 0,1 %
- Separation: ≥ 40 dB
- Impedance: 4
- FM Radio: Yes
• Power supply: 220 \~ 240 V; 50/60 Hz
- Bluetooth version: 4.0
• Operational range: up to 10 m
• Power consumption: 42 W
• I/O ports: 2x RCA, coaxial, optical, speaker terminal
- Speaker diameter: 8", 4", 2"
- Set includes: remote control, wireless microphone

LEARN MORE

For more information on this product, go to www.krugermatz.com.

Visit www.krugermatz.com website for more products and accessories.

In case of any doubts or questions reach out to our Frequently Asked Questions section.

"The LECHPOL ELECTRONICS Sp. z o.o. Sp.k company declares that product KM0542 is consistent with the essential requirements and other relevant provisions of directive 2014/53/UE. The proper declaration for download from www.lechpol.eu"

EN

English

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or Its literature, indicates that It should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal.

Made in China for LECHPOL ELECTRONICS Sp. z o.o. Sp.k., ul. Garwolińska 1, 08-400 Miętne.

QUESTIONS DE SÉCURITÉ

VOLUME TREBLE BASS MIC. VOL ECHO MIC1 MIC2

PANNEAU ARRIÈRE

VOLUME TREBLE BASS MIC. VOL ECHO MIC1 MIC2

ACHTERPANEEL

1. FM antenne
2. Audio ingang
3. Coaxiale ingang
4. Optische ingang
5. Audio ingang
6. Voedingsschakelaar
7. Voedingskabel

RADIO ANTENNA AUDIO INPUT SPDIF INPUT Coaxial Lock Optical OUTPUT - + Only connect endosted slave unit or contact your supplier WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION DO NOT TOUCH THE RACE SIDE OF THE SPEAKER Krüger&Matz 2.0 active theatre speakers Model: KM0542 Power: 42 W x2 Made in China for LECH-POL ELECTRONICS sp. 2 n.o. 9 p.m. Mjärne, st. Garwettinska 1, 08-431 Garwöln. AC220V-240V,5366Hz

AFSTANDSBEDIENING

graph TD
    A["L"] --> B["R"]
    C["Optical"] --> D["SPDIF INPUT Coaxial"]

VOLUME TREBLE BASS MIC. VOL ECHO MIC1 MIC2 ① ② ③ ④ ⑤ ⑥ ⑦

PANEL TYLNY

VOLUME TREBLE BASS MIC. VOL ECHO MIC1 MIC2

PANOUL DIN SPATE

1. Antena FM
2. Intrare Audio
3. Intrare coaxiala
4. Intrare optica
5. lesire audio
6. Comutator alimentare
7. Cablu alimentare

RADIO ANTENNA AUDIO INPUT SPDIF INPUT Coaxial Lock Optical OUTPUT - + Only connect endosted slave unit or contact your supplier WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION DO NOT TOUCH THE RACE SIDE OF THE SPEAKER Krüger&Matz 2.0 active theatre speakers Model: KM0542 Power: 42 W x2 Made in China for LECH-POL ELECTRONICS sp. 2 n.o. w/x. Mjärne, st. Garwettinska 1, 08-431 Garwöln. AC220V-240V,53960Hz

TELECOMANDA

graph TD
    A["L"] --> B["R"]
    C["Optical"] --> D["SPDIF INPUT Coaxial"]

Completely black image with no visible content, text, or symbols.

QR code image containing encoded data, no visible human-readable text

www.krugermatz.com

Krüger&Matz is a registered trademark