Punch P1S652 - Speaker Rockford Fosgate - Free user manual and instructions

USER MANUAL Punch P1S652 Rockford Fosgate

Printed in China Full Range Speakers Serial Number: Date of Purchase: Installation & Operation Installation et fonctionnement Instalación y funcionamiento Einbau und Betrieb Installazione e funzionamento Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Speakers – 1 Year. Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions. Product purchased by consumers from an Authorized Rockford Fosgate Dealer in another country are covered only by that country’s Distributor and not by Rockford Corporation.Who is CoveredThis warranty co ers only the original pur chaser of Rockford product purchased from an Authorized Rockf

d F osgate Dealer in the United States.In or der to receive service, the purchaser must provide Rockf d with a copy of the receipt stating the customer name , dealer name, product purchased and date of pur chase

oducts f ound to be defective during the warranty period will be repaired or replaced (with a product deemed to be equivalent) at Rockf d's discretion.What is Not Covered

1. Damage caused by accident, abuse, improper operations, water, theft, shipping

2.Any cost or expense related to the removal or reinstallation of product

3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service Center

4.Any product which has had the serial number defaced, altered, or removed

5. Subsequent damage to other components6.Any product purchased outside the U.S.

7.Any product not purchased from an Authorized Rockford Fosgate Dealer Limit on Implied Warranties Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the period of the express warranty set forth above.Some states do not allow limitations on the length of an implied warranty, so this limitation may not apply.No person is authorized to assume for Rockford Fosgate any other liability in connection with the sale of the product. w to Obtain Ser vice Contact the Authorized Rockford Fosgate Dealer you purchased this product from. If you need further assistance, call 1-800-669-9899 for Rockford Customer Service.You must obtain an RA# (Return Authorization number) to return any product to Rockford Fosgate.You are responsible for shipment of product to Rockford.

arr anty This product meets the current EU warranty requirements, see your Authorized dealer for details. 2009 Rockford Corporation.All rights reserved. Rockford Fosgate and the Rockford Fosgate logo are either registered trademarks or trademarks of Rockford Corporation.

TEMENT Rockford Fosgate Rockford Corporation600 South Rockford DriveTempe,Arizona 85281 U.S.A.In U.S.A., [phone]Customer Service 1-800-669-9899 www.rockfordfosgate.com 01/2009 B.M.01/2009 E.R.1230-55478-022 Before beginning any installation, follow these simple rules:1. Be sure to carefully read and understand the instructions before attempting toinstall these speakers.2. For safety, disconnect the negative lead from the battery prior to beginning theinstallation.3. For easier assembly, we suggest you run all wires prior to mounting your speakersin place.4. Use high quality connectors for a reliable installation and to minimize signal orpower loss.

Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on anyvehicle. If installation in a boat, take care not to cut or drill through the main hull.6. Never run wires underneath the vehicle. Running the wires inside the vehicle orhull area provides the best protection.7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall. 1. Determine where the speakers will be mounted. Ensure an area large enough forthe speaker to mount evenly. Be sure that the mounting location is deep enough or the speaker to fit; if mounting in a door, operate all functions (windows, locks,etc.) through their entire operating range to ensure there is no obstruction.

Ref er to the specification chart to determine the proper diameter hole to cut for your speaker model. Cutting and mounting templates can be found atwww.rockfordfosgate.com. Mark the locations for the mounting scr

ws. Drill the holes with a 1/8" bit.4. Feed the speaker wires through the cutout and connect to the speaker terminals.Be sure to observe proper polarity when connecting the wires.The speaker's positive terminal is indicated with a "+".5a. On models with slotted holes, fit the speaker into the cutout and install thescrews in the slots at the top and bottom.This will allow you to rotate the speak-er to match the remaining mounting holes.When aligned, tighten the screws.5b. On models with a trim ring, fit the trim ring over the speaker and mount intoplace using four (4) screws.6. Tighten the screws until the speaker is snug in place to prevent rattling. Do notover tighten the screws.NOTE:For P142, P1462, P152, P1S652 and P1653 only, if needed use theadapter plate provided to mount the speaker. See Adapter PlateTemplates at the end of this manual. SAFETY CARTON CONTENTS CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

• (1) Pair Punch Series Full Range Speakers• (1) Pair of grilles/trim rings (P152, P1S652, P1653, P1692 and P1694 only)• (1) Pair of adapter plates (P142, P1462, P1572 only)• (2) Pair of adapter plates (P152, P1S652, P1653 only)• Mounting Hardware INSTALLATION CONSIDERATIONS MOUNTING Cutout Hole Position to Align Holes Rear Deck Cutout Hole Example of standard door installation Example of rear deck installation CutoutHole Position to Align Holes Rear Deck Cutout Hole Example of standard door installation Example of rear deck installation

Mount P1462 4"x6" 5"x7" Hole Mounting Adapter Plate Template Remove Shaded Areas to Mount P142 4"10 Remove Dark Shaded Areas Adapter Plate Template – 6.5" Hole Mounting Mounting for P152 5.25" Remove Shaded Areas to Mount P1S652 6.5" Shallow11 For 5"x7" Hole Mounting - Remove Dark Shaded Areas Remove For Optional Tweeter Adapter Plate Template – 6"x9" Hole Mounting Mounting for P152 5.25" Remove Shaded Areas to Mount P1S652 6.5" Shallow12 For 5"x7" Hole Mounting - Remove Dark Shaded Areas Remove For Optional Tweeter Adapter Plate Template – 6"x9" Hole Mounting Remove Shaded Areas to Mount P1653 6.5"