EasyManual 
SBSD137HBB - Tumble drier GE - Free user manual and instructions
Find the device manual for free SBSD137HBB GE in PDF.
User questions about SBSD137HBB GE
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Tumble drier in PDF format for free! Find your manual SBSD137HBB - GE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SBSD137HBB by GE.
USER MANUAL SBSD137HBB GE
Installation Instructions KIT CONTENTS 4 Support Pads4 Mounting ScrewsDrawer Divider
Phillips Head Screwdriver9/16” Open End Wrench or Adjustable Wrench8 mm Socket Wrench
Carefully lay the washer or dryer on its side to access the leveling legs on the bottom of the appliance.IMPORTANT: Do not lay the washer or dryer on its back! Do not remove the shipping bolts on the back side of the washer. The bolts must remain in place until the washer is returned to an upright position. Use an open-end wrench to remove the washer or dryer leveling legs. INSTALLATION PREPARATION Remove the packaging.The Drawer divider is taped at the top of the shipping carton. Remove the divider and set aside for final installation.Flatten the product carton to use as a pad to lay the washer or dryer down on its side. Continue using the carton to protect the finished floor in front of the installation location.Back out and remove all 4 leveling legsInstructions en français : ................ 4Instrucciones en español: ............... 8For Washer Models: GBVH5140, GBVH6260, GCVH6260, GCVH6600, GCVH6800, GFAN1000, GFAN1100, GFWH1200, GFWH1300, GFWH1400, GFWH1405, GFWH2400, GFWH2405, GFWN1000, GFWN1100, GFWN1200, GFWN1300, GFWS1500, GFWS1505, GFWS3500, GFWS3505, GHDVH626, GHDVH670, GMAN1200, WBVH5100, WBVH6240, WCVH5300, WCVH6260, WCVH6600, WCVH6800, WHDVH626 & WHDVH660For Dryer Models: DBVH510, DBVH512, DCVH515, DCVH660, DHDVH52, DHDVH66, GFDM245, GFDN100, GFDN110, GFDN120, GFDN130, GFDN240, GFDN245, GFDS140, GFDS145, GFDS150, GFDS155, GFDS350, GFDS355, GFMN100, GFMN110, GFMN240, GFMS350, GFMS355, GMMN120, PBVH415, PCVH565, PCVH680, PDVH515, PHDVH52 & PHDVH57
Read these instructions completely and carefully.
IMPORTANT ³6DYHWKHVHLQVWUXFWLRQV for local inspector’s use.
IMPORTANT ³2EVHUYHDOOJRYHUQLQJ codes and ordinances.• Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.• Completion time – 1 to 2 hours• Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty.
CAUTION ³'XHWRWKHVL]HDQGZHLJKW
of these products, and to reduce the risk of personal injury or damage to the product, TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.• See washer and dryer installation instructions for additional installation requirements and guidelines. 49-90321-2 175D1807P589 11-13 GE2 Installation Instructions
Place the pedestal against the bottom of the unit. Check to be sure the drawer front is at the front of the unit.
Align the holes in the pedestal with the holes in the bottom of the unit. Use a Phillips screwdriver to install the 4 screws through the pedestal DQGLQWRWKHXQLW³GRQRWWLJKWHQ
Slide the pedestal toward the unit, until it is aligned front to back. Use an 8 mm socket wrench to securely tighten the screws.
Pull the drawer out as far as it will go.
Remove screws from drawer slides. Slide drawer out of the base and set aside.
Locate the 4 support pads from the parts package. Each pad has 2 protrusions that fit into the holes on top of the pedestal. Press the rubber pads into each set of corner holes on the top of the pedestal as shown. NOTE: The support pads should be installed on the dryer only. DO NOT INSTALL THESE PADS ON
THE WASHER PEDESTAL.3
Installation Instructions
Locate the 4 legs from the parts package and install.
Stand the washer or dryer upright. Move it close to its final location.
Make sure that the washer or dryer is level by placing a spirit level on top. Check side to side and front to back.
Use an open ended wrench to adjust the legs in and out. Tighten the lock nut against the bottom of the pedestal. 127(7RPLQLPL]HYLEUDWLRQWKHORFNLQJQXWV must be tight.
Remove the 4 shipping screws on the back side of the unit.
Check to be sure the slides are closed.
Slide the drawer into the opening. Align the drawer supports to the slides on each side.
Reinstall the original screws into each drawer slide. Tighten both screws.
Open the drawer fully. Slide drawer divider into slots in the center of the drawer. The drawer should slide smoothly when you push it closed.
Refer to the washer or dryer Installation Instructions to complete the installation.
$OLJQH]OHVWURXVGXVRFOHDYHFOHVWURXV
