SPX220EXT - Pressure washer Sun Joe - Free user manual and instructions

USER MANUAL SPX220EXT Sun Joe

Original instructions.© 2022 Snow Joe, LLC. All rights reserved.

SAVE THESE INSTRUCTIONS

A Division of Snow Joe , LLC Model SPX220E-XT Form No. SJ-SPX220E-XT-880E-M-FTY

IMPORTANT! Safety Instructions All Operators Must Read These Instructions Before Use mWARNING! This indicates a hazardous situation, which, if not avoided, could result in death or serious injury. mCAUTION! This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury. mDANGER! This indicates a hazardous situation, which, if not followed, will result in death or serious injury. IMPORTANT SAFETY INSTRUCTIONS WARNING – When using this product, basic precautions should always be followed, including the following:

• Read all the instructions before using the product.

• To reduce the risk of injury, close supervision is necessary when a product is used near children.

• Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.

• Stay alert – watch what you are doing.

• Do not operate the product when fatigued or under the inuence of alcohol or drugs.

• Keep operating area clear of all persons.

• Do not overreach or stand on unstable support. Keep good footing and balance at all times.

• Follow the maintenance instructions specied in the manual.

• This product is provided with a ground fault circuit interrupter built into the power cord plug. If replacement of the plug or cord is needed, use only identical replacement parts.

• Warning – risk of injection or injury – do not direct discharge stream at persons. General Safety mWARNING! This appliance is not intended for use by children or by unassisted, unsupervised persons whose physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. Before starting up your machine, please check it carefully for any defects. If you nd any, do not start up your machine. Contact your authorized Snow Joe

dealer or call the Snow Joe

customer service center at 1-866-SNOWJOE (1-866-766-9563). mWARNING! When using the pressure washer, basic safety precautions should always be followed to reduce the risk of re, electric shock, and personal injury. These include:

• Know your product – Know how to stop the machine and bleed pressure quickly. Thoroughly familiarize yourself with the controls.

• Keep bystanders away – All visitors and pets should be kept a safe distance away from the work area.

• Use the right product – Do not use this machine for any job except that for which it is intended.

• Dress properly – Do not wear loose clothing or jewelry. They can get caught in moving parts. Protective rubber gloves and non-slip footwear are recommended when working outdoors.

mCAUTION! – Exercise caution to avoid slipping or falling. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.

• Stay alert – Watch what you are doing. Use common sense. Do not operate the pressure washer when you are tired, or under the inuence of alcohol or drugs.

• WARNING! Risk of Injection or Injury – Do not direct discharge stream at persons.

• Do not overreach – Keep proper footing and balance at all times.

• Avoid unintentional starting – Do not carry a plugged- in machine with your nger on the trigger. Make sure the switch is off before plugging in the machine.

• Do not abuse the cord – Never carry the machine by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges.

• Use safety glasses – Also use safety footwear, snug-tting clothing, protective gloves, hearing and head protection.2

• Check the water temperature – This pressure washer is not meant to pump hot water. NEVER connect it to a hot water supply as it will signicantly reduce the life of the pump.

• Store indoors – NEVER store the pressure washer outdoors or where it could freeze. The pump could be seriously damaged.

• Inspect electrical cables – The insulation of the power cord should be perfectly intact. If the power cord is damaged or shows any signs of wear or tear, do not use the pressure washer. Contact your authorized Snow Joe

dealer or call the Snow Joe

customer service center at 1-866-SNOWJOE (1-866-766-9563). mWARNING! Do not use this appliance without reading this instruction manual. mWARNING! This appliance has been designed for use with cleaning agents that are recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance. mWARNING! Do not use the appliance within range of persons unless they are wearing protective clothing. mWARNING! High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself.

• Do not direct the jet at yourself or others in order to clean clothes or footwear.

• Risk of explosion – Do not spray ammable liquids.

• Disconnect the tool – Disconnect from the electrical power supply before performing any maintenance task.

• Keep children away – This high-pressure electric power washer must not be used by children or untrained personnel.

• To ensure appliance safety, use only original replacement parts from the manufacturer or those approved by the manufacturer. mCAUTION! To prevent damage to the appliance, do not allow it to operate dry. Before starting the appliance, make sure that it has a proper and stable supply of water. mWARNING! Water that has owed through backow preventers is considered to be non-potable. mWARNING! During cleaning, maintenance or when replacing parts, the machine must be disconnected from its power source by removing the plug from the socket outlet. mWARNING! High-pressure hoses, ttings, and couplings are important for the safe operation of the appliance. Use only hoses, ttings, and couplings recommended by the manufacturer.

• Check for damaged parts – Do not use the appliance if the supply cord or other important parts of the appliance are damaged (e.g. safety devices, high-pressure hoses, trigger gun). mWARNING! If an extension cord is used, the plug and socket must be of watertight construction. mWARNING! Inadequate extension cords can be dangerous.

• This high-pressure electric power washer must not be used at temperatures below 32ºF (0°C). mWARNING! Power cords on drums should always be completely unwound to prevent the cord from overheating.

• Power cord connections should be kept dry and off the ground.

• If the power cord is damaged, do not use the appliance. Contact your authorized Snow Joe

dealer or call the Snow Joe

• Keep the machine on a stable, at surface during operation, handling, transportation, and storage. Sudden overturn of the machine can cause bodily injury.

• In the event of an accident or breakdown, switch off the machine immediately. (If contact with detergent occurs, rinse with an abundance of clean water.) Electrical Safety ATTENTION: If there are problems with the electrical MAINS, short voltage drops may appear when starting the equipment. This can, in turn, inuence other equipment (e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax < 0.335 OHM, such disturbances are not expected. (If you require assistance, contact your local supply authority for further information.) mWARNING! Electrical Shock Hazard – Before starting up your machine, please check it carefully for any defects. If you nd any, do not start up your machine and contact your distributor. The following should be observed when connecting the high-pressure electric power washer to the electric supply:

• The electric supply connection should be performed by a qualied person.

• The electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to the earth exceeds 30 mA for 30 ms or a device that will interrupt the earth circuit (GFCI). IMPORTANT: Only use water without any impurities. If there is a risk of running sand into the inlet water (i.e. from your own well), an additional lter should be installed. Safety Devices The unloader valve can reduce pressure if it exceeds preset values. The spray gun features a locking device. When the lock is activated, the spray gun cannot be operated.3 1. Thermal sensor – A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sensor has cooled.2. Double insulation – In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be performed only by qualied service personnel at an authorized Snow Joe + Sun Joe dealer. Replacement parts for a double-insulated appliance must be identical to the parts they replace. A double-insulated appliance is marked with the words “Double Insulation” or “Double Insulated.” The symbol (square within a square) may also be marked on the appliance.3. Ground fault circuit interrupter (GFCI) protection – this product is provided with a Ground Fault Circuit Interrupter built into the power cord plug. This device provides additional protection from the risk of electric shock. If replacement of the plug or cord is needed, use only identical replacement parts that include GFCI protection.4. It is not recommended to use an extension cord with this pressure washer. The unit comes standard with a 35 ft GFCI power cable. Using an extension cord may cause a drop in line voltage resulting in loss of power and overheating. Use only extension cords that are intended for outdoor use. These extension cords are identied by marking "Acceptable for use with outdoor appliance; store indoors while not in use". Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. Always disconnect extension cord from the receptacle before disconnecting the product from the extension cord.5. To reduce the risk of electric shock, this appliance has a polarized plug (i.e. one blade is wider than the other). The appliance plug will t into a polarized outlet only one way. If the appliance plug does not t fully into the outlet, reverse the plug. If the plug still does not t, make sure that you are using the correct polarized wall outlet. If the plug still does not t, contact a qualied electrician to install the proper wall outlet. Do not modify the appliance plug, power cord receptacle, or power cord plug in any way. 6. To prevent the appliance cord from disconnecting from the extension cord during operation, make a knot with the two cords as shown in Table 1.7. Do not abuse the cord. Never pull the pressure washer by the cord or yank the cord to disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp edges. m WARNING m Electric shock may cause SEVERE INJURY or DEATH. Heed these warnings:• Do not allow any part of the electric pressure washer to make contact with water while it is in operation. If the appliance becomes wet while turned off, wipe dry before starting. • Do not use an extension cord over 25 ft. The pressure washer comes equipped with a 35 ft power cable. Combined cord length must not exceed 60 ft. Any extension cord must be 14-gauge (or heavier) to safely power the pressure washer.• Do not touch the appliance or its plug with wet hands or while standing in water. Wearing rubber boots offers some protection. EXTENSION CORD CHARTCord Length:Min. Wire Gauge (A.W.G.):25 ft (7.6 m) (B) Connect plug and receptacleCord set Appliance cord(A) Tie cord as shownTable 1. Method of Securing Extension Cord4 Risk of Electrocution

• Inspect cord before using.

• Do not use if cord is damaged.

• Keep all connections dry and off the ground.

• Do not touch plug with wet hands.

• Keep cord away from heat and sharp edges.

• Do not spray electrical apparatus and wiring. Risk of Explosion

• Do not spray ammable liquids.

• Do not use acids, bases, solvents, or any ammable material in this product. These substances can cause physical injuries to the operator and irreversible damage to the machine. Additional Safety Instructions

• High-pressure: keep clear of nozzle.

• Injection hazard: equipment can cause serious injury if the spray penetrates the skin.

• Do not point the gun at anyone or at any part of the body.

• In case of skin penetration, seek medical aid immediately.

• Before servicing, cleaning, or removing any parts, shut off the power and relieve pressure.

• This machine is not suitable for connection to the potable water mains. Product Description Purpose

• This high-pressure electric power washer is intended for residential use to clean vehicles, machines, buildings, facades, etc. Areas of Application

• Never use the machine in potentially explosive areas under any circumstances!

• The operating temperature must be between 32ºF (0°C) and 104°F (40°C).

• The machine consists of an assembly with a pump, which is encased in a shock-absorbing housing. To provide the operator with an optimal working position, the machine is equipped with a stainless steel lance and a non-slip handle grip, whose shape and conguration comply with applicable regulations.

• Do not cover or modify the stainless steel lance or the spray nozzles in any way.

• The high-pressure electric power washer is designed to be used with cold or lukewarm water; higher temperatures can damage the pump.

• Do not use water that is dirty, gritty, or contains any chemical products, as these could impair operation and shorten the life of the machine.5 Safety Symbols The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. To reduce the risk of injury, user must keep all bystanders at least 49 ft (15 m) away. Always keep the power cable away from heat sources, oils, or sharp edges. Immediately remove plug from the mains if the cable is damaged, frayed, or entangled.

MANUAL(S) – Read, understand, and follow all instructions in the user manual(s) before attempting to assemble and operate. SAFETY ALERT – Indicates a precaution, a warning, or a danger.

WEAR EYE AND HEARING

PROTECTION – For protection against injury, wear ear defenders and safety goggles. Double Insulation – When servicing, use only identical replacement parts. WARNING! Do not expose the unit to rain or wet conditions. Keep dry. Machine not suitable for connection to the potable water mains. WARNING! Electrical shock hazard. WARNING! Turn the machine OFF and disconnect it from the power supply before inspecting, cleaning, changing accessories, or conducting any other maintenance task. Symbols SymbolsDescriptions Descriptions Wear non-slip footwear that will protect your feet and improve your footing on slippery surfaces. Wear safety gloves during use to protect hands. Store indoors. Never store the pressure washer outdoors. If the pump freezes, permanent damage may result.6

11. Detergent bottle with foam cannon

Know Your Electric Pressure Washer Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

• Electric pressure washer

• Detergent bottle with foam cannon

• Needle clean-out tool

• Manual with registration card

1. Carefully remove the pressure washer and check to see

that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or missing parts, DO NOT return the unit to the store. Please call the Snow Joe

customer service center at 1-866-SNOWJOE (1-866-766-9563). NOTE: Do not discard the shipping carton and packaging materials until you are ready to use your new electric pressure washer. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations. IMPORTANT! The equipment and packaging materials are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a suffocation risk! Assembly

1. Position the washer as CLOSE as possible to the

2. The washer must be used on a secure and stable surface

in a standing, upright position (Fig. 1). Fig. 1

3. Connect one end of pressure hose to the trigger gun.

Connect the other end to the washer water outlet and reinforce the connection by the sleeve (Fig. 2-3). Fig. 2 Fig. 3

4. Insert the locking lugs on the extension lance into the

trigger gun. Twist until it engages (Fig. 4).8 Fig. 4

5. Connect one end of the garden hose to the washer water

inlet and connect the other end to the water supply (Fig. 5-6). mWARNING! The machine is not suitable for connection to the potable water main. Fig. 5 Fig. 6 mWARNING! Keep hose away from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. Do not attempt to mend a damaged hose.

6. Make sure the switch is in OFF position before plugging

into the power outlet (Fig. 7). Fig. 7

7. Connect the pressure washer to the electrical supply

matching "SPECIFICATION" in this manual. Press the reset button on the GFCI plug until the indicator illuminates to make sure the washer is ready for operation (Fig. 8). Fig. 8 NOTE: The GFCI may need to be reset when rst plugged into the electric outlet. Press the "Reset" button until the power light indicator on the GFCI illuminates. Operation mIMPORTANT! This pressure washer is equipped with a micro-switch sensitive to water ow. This Total Stop System (TSS) senses water ow in the pump. When the trigger is released, water stops owing through the pump. The TSS then automatically turns the motor off to protect the pump from overheating, thus saving energy and prolonging pump life.

1. Turn the water supply tap on completely.

2. Make sure the safety lock is unengaged, then press

the trigger for a few seconds until water ow is steady. This will allow air to escape and discharge any residual pressure in the hose.

3. Press the ON/OFF switch to start the pressure washer.9

Using the Nozzles Each nozzle has a different spray pattern. Determine the best nozzle according to the cleaning task to be performed. This electric pressure washer is equipped with two (2) nozzles that easily snap onto the Quick-Connect collar of the stainless steel lance. mCAUTION! NEVER change nozzles without locking the safety lock on the trigger handle. mWARNING! High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, pets, live electrical equipment, or the appliance itself. To connect a nozzle to the extension lance:

1. Turn off the pressure washer and shut off the water supply.

Pull the trigger to release the water pressure.

2. Engage the safety lock on the trigger to prevent

unintentional start (Fig. 9). Fig. 9

3. Pull back the collar and insert a desired nozzle. Release

the collar to lock the nozzle in place (Fig. 10). Fig. 10 To disconnect a nozzle from the extension lance once the cleaning job is complete:

4. Turn off the pressure washer and shut off the water supply.

Pull the trigger to release water pressure.

5. Engage the safety lock on the trigger to lock the trigger.

6. Remove the nozzle by placing your hand over the nozzle

while pulling back on the Quick-Connect collar. mWARNING! Do not make changes to the nozzle while the trigger is engaged. Doing so could result in damage to the pressure washer or injury to the user. Working with Detergents When cleaning with the pressure washer, some cleaning tasks can be solved with water alone, but for most tasks cleaning with detergent allows for more effective dirt removal. For additional cleaning power, the unit comes equipped with a detergent spray bottle with foam cannon. mWARNING! Use only detergents specically designed for use with pressure washers, such as Sun Joe

(SPX-APC1G). DO NOT USE household detergents, acids, alkaline solutions, bleaches, solvents, ammable material, or industrial grade solutions. These could damage the pressure washer. Many detergents may require mixing prior to use. Prepare the cleaning solution as instructed on the solution bottle.

1. Remove the foam cannon cap with detergent suction tube

2. Fill the foam cannon bottle with detergent designed

specically for use with pressure washers (Fig. 11). Fig. 11

3. Recap the foam cannon, and attach it to the extension

lance by snapping it onto the Quick-Connect collar until it clicks into place (Fig. 12). Fig. 1210

4. Apply detergent from the bottom to the top of the dry

surface to be cleaned. Applying detergent in this manner will dissolve dirt most effectively. NOTE: Wetting the surface rst is not recommended as it dilutes the detergent and reduces its cleaning ability. mCAUTION! Always test the detergent in an inconspicuous area before use.

6. Allow the detergent to remain on the surface for a short

time before rinsing with the pressure washer. Do not allow the detergent to dry on the surface. mCAUTION! Damage may occur to painted surfaces if the detergent is allowed to dry on them. Wash and rinse a small section at a time. Avoid working on hot surfaces or in direct sunlight. Rinsing with the Pressure Washer

1. Turn off the pressure washer and shut off the water supply.

2. Pull the trigger to release water pressure.

3. Engage the safety lock on the trigger to lock the trigger

4. Remove the detergent bottle with foam cannon by holding

the bottle while pulling back on the Quick-Connect collar.

5. Select the right nozzle for the job:

This nozzle creates the widest area of cleaning with relatively low pressure. It is intended for light or delicate cleaning applications such as wood decks and other soft or delicate surfaces.

This nozzle rotates in a zero to 15 degree circular motion spray pattern to break down tough dirt and grime. It covers an area of 4 to 8 inches wide, depending on the distance between the tip and the surface being cleaned.

6. Start at the top of the area to be rinsed and work your way

down, making sure to overlap your strokes. mIMPORTANT! NEVER USE:

• Bleach, chlorine products, and other corrosive chemicals

• Liquids containing solvents (e.g. paint thinners, gasoline, oils)

• Tri-sodium phosphate products

• Acid-based products These chemicals will harm the unit and will damage the cleaning surface. Shutting Down

1. Turn the switch to the OFF (0) position and unplug the

power cord from the power outlet.

2. Turn off the water supply.

3. Hold the trigger to release water pressure.

4. Disconnect the garden hose from washer water inlet.

5. Disconnect the pressure hose from the trigger gun.

6. Release the trigger and engage the safety lock.

mWARNING! Turn off the water supply and squeeze the trigger to depressurize the unit. Failure to do so could result in personal injury due to discharge of high-pressure water. Taking a Break If you are taking a break of ve minutes or more between cleaning tasks:

1. Engage the gun safety lock (Fig. 9).

2. Turn the switch to the OFF (0) position.

3. Unplug the power cord from the power outlet.

Storage mCAUTION! Always store your pressure washer in a location where the temperature will not fall below 32ºF (0ºC). The pump in this machine is susceptible to permanent damage if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE WARRANTY.

• Store the pressure washer indoors in a dry, covered area where it is not subject to adverse weather conditions.

• It is important to store this product in a frost-free area.

• Always empty water from all hoses, the pump, and the foam cannon before storing. mCAUTION! The use of a pump protector is recommended to prevent cold weather damage during storage over the winter months. Winterizing + Long-Term Storage If you must store your pressure washer in a location where the temperature falls below 32ºF (0ºC), you can minimize the chance of damage to your machine by utilizing the following procedure:

• Disconnect all water connections.

• Turn on the machine for a few seconds until the remaining water in the pump exits. Turn off immediately.

• Do not allow the high-pressure hose to become kinked.

• Store the machine and accessories in a room that does not reach freezing temperatures.

• Do not store near a furnace or other sources of heat that may dry out the pump seals.

• Operate the pressure washer with non-corrosive/non-toxic anti-freeze, a pump saver, or a pump protector before storing for the winter. mWARNING! Before reusing, completely ush the unit out with clear water. Anti-freeze products can damage paintwork, so you must ensure there is no anti-freeze left in the system before using it again.11 Maintenance mCAUTION! Before working on the pressure washer, disconnect the plug from the power supply socket.

1. To ensure good performance, check and clean the water

inlet lter (Fig. 13). Fig. 13

2. Remove the lter and rinse with warm water to prevent

any foreign matter from clogging the pump (Fig. 14). Fig. 14

3. Clean the nozzle with the needle clean-out tool provided

(Fig. 15). Remove the stainless steel lance from the gun; remove any dirt from the nozzle hole and rinse. Fig. 15

4. Remove additional debris by back ushing water through

the nozzle and extension lance. To do this, place the end of your garden hose (with water running) to the tip of the nozzle, pushing water and debris out of the back opening of the nozzle and extension lance. Disposal Recycling the Washer

• Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities.

• Contact your local government agency for information regarding the collection systems available.

• If electrical appliances are disposed of in landlls or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

• When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal free of charge. Service + Support If your Sun Joe

SPX220E-XT electric pressure washer requires service or maintenance, please call the Snow Joe

customer service center at 1-866-SNOWJOE (1-866-766-9563). Model + Serial Numbers When contacting the company, reordering parts, or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below. Record the following numbers from the housing or handle of your new product:S P X 2 2 0 E - X T Model #:Serial #:12 Troubleshooting

• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that its parts are in proper working order.

• The hose must be connected and the water turned on before operating your unit. Failure to do so will damage the pump motor and void your warranty.

• Total Stop System (TSS) – The motor will shut OFF and remain in standby mode during periods of inactivity, or as soon as the unit is pressurized. THIS IS NORMAL. Simply squeeze the trigger to restart the pump motor.

• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues. Problems Possible Cause Possible Solution Machine refuses to start

• Power failure/machine not plugged into a working receptacle.

• Defective extension cord.

• Check to make sure machine is plugged into a working outlet.

• Check the power cord and reset the GFCI. Try a different outlet.

• Replace fuse. Switch off any other machines that are using the same circuit.

• Try the unit without an extension cord.

• Check the hoses and connections are airtight.

• Clean or replace valves/seals.

• Please call the Snow Joe

• Check that the mains voltage corresponds to specication on the model tag.

• Install a fuse with a higher amp rating than the amp consumption of the machine. Try the unit without an extension cord.

• Allow machine to run by holding the trigger until regular working pressure resumes.

• Check that the water supply corresponds to the specications required.

• Clean the water inlet lter.

• Straighten out the hose to remove any kinks/blockages.

• Please call Snow Joe

• Wait for pump/hoses or accessories to thaw.

• Connect inlet water.

• Clean the water inlet lter.

• Valves dirty, worn out, or stuck.

• Pump seals worn out.

• Nozzle partially blocked.

• Inadequate supply of mains water.

• Nozzle partially blocked.

• Trigger mechanism is broken.

• Water inlet lter blocked.

• Nozzle blocked. Fluctuating pressure Machine stops Fuse blows Machine pulsating Machine often starts and stops by itself Machine starts, but no water comes out13 NOTE: Accessories are subject to change without any obligation on the part of Snow Joe

to provide notice of such changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe

customer service center at 1-866-SNOWJOE (1-866-766-9563). Sun Joe’s complete line of premium pressure washer accessories and attachments make it easy to get your dirty work done, and also help you get the most out of your model! SHOP ONLINE now at sunjoe.com Optional Accessories

WARNING! ALWAYS use only authorized Snow Joe

replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe

if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. Accessories Item Model Spray Tip Set (Compatible with most SPX Series Pressure Washers) SPX-TSN-34S 20 ft Pressure Hose (For SPX Pressure Washer Series) SPX3000-33 Solid Brass Universal Quick-Connect Coupler (Garden Hose to Pressure Washer Adapter) SPX-UQC Sun Joe

House + Deck All-Purpose Pressure Washer Rated Concentrated Cleaner Sun Joe

Premium Snow Foam Pressure Washer Rated Car Wash + Cleaner Sun Joe