Prague TPZ15364 - Speaker Turbosound - Free user manual and instructions

Product type	Passive speaker
Brand	Turbosound
Model	Prague TPZ15364
Category	Professional speaker
Dimensions (H x W x D)	700 x 450 x 450 mm
Weight	25 kg
Power supply	Passive (no power supply required)
Connectivity	6.35 mm jack input
Main functions	Professional sound reproduction, use in sound reinforcement
Maintenance and cleaning	Clean with a dry cloth; do not use liquids
Safety	Do not open the cabinet; risk of electric shock; use only quality cables
Spare parts and repairability	Repair by a qualified professional only; contact an authorized service center
General information	Passive speaker from the Prague series, designed for use in live sound or fixed installation

Frequently Asked Questions - Prague TPZ15364 Turbosound

How to connect the Prague TPZ15364 speaker?

Use a speaker cable with a 6.35 mm mono jack connector. Plug one end into the amplifier output and the other into the speaker input. Make sure the amplifier is turned off when connecting.

What is the impedance of the speaker?

The nominal impedance is 8 ohms. Make sure your amplifier is compatible with this impedance.

How much power can I send to this speaker?

The rated power is about 500 W RMS. Use an amplifier with suitable RMS power to avoid damaging the speaker.

How to clean the speaker?

Clean the cabinet with a soft dry cloth. Never use chemicals or liquids. For the grille, gentle dusting is recommended.

Can I use this speaker outdoors?

This product is designed for indoor use. Do not expose it to rain, moisture, or extreme temperatures. If used outdoors, place it in a sheltered area.

What to do if the speaker produces no sound?

Check the cable connections, ensure the amplifier is on and volume is set. Test with another audio source. If the problem persists, contact a professional.

Can I repair the speaker myself?

No, the interior contains no user-serviceable parts. Any repair must be done by a qualified technician to avoid risk of electric shock.

What is the warranty on this product?

The limited warranty is 2 years for manufacturing defects. For more details, visit music-group.com/warranty.

How to mount the speaker on a stand?

The speaker has a standard 35 mm stand mount. Use a suitable stand and ensure it is stable and secure before placing the speaker on it.

Can I use multiple speakers together?

Yes, you can connect multiple speakers in parallel. Ensure the total impedance remains compatible with your amplifier (e.g., two 8 ohm speakers in parallel result in 4 ohms).

USER MANUAL Prague TPZ15364 Turbosound

Four-panel black-and-white photo collage showing a crowded radio, a live audio workstation with a speaker, a music recording center, and a cheering crowd holding a microphone (no visible text or symbols)

Prague TPA/TPZ SERIES

TPA122/64/95/00 / TPA122/64/95/00-WH

TPA152/64/95 / TPA152/64/95-WH

TPZ122/64

TPZ152/64

TPZ153/64

Arrayable 2-Way/3-Way 12/15" Full Range Loudspeaker for Installation Applications Quickstart Guide

Four black audio/video amplifiers arranged in a row, no visible text or labels

Terminals marked with this symbol carry electrical current of suffi client magnitude to constitute risk of electric shock. Use only high quality commercially available speaker cables with plugs pre-installed. All other installation or modification should be performed only by qualified personnel.

This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Caution To reduce the risk of electric shock, do not remove the top cover for the rear section. No user serviceable parts inside. Refer servicing to qualified personnel.

Caution To reduce the risk of fi re or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dropping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions, Repairs have to be performed by qualified service personnel.

1. Read these instructions.

2. Keep these instructions.

3. Heon all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Use only attachments/accessories specified by the manufacturer.

1. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used,

moving the cart/asperatus combination to avoid injury from tip over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time.

1. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

2. The apparatus shall be connected to a MAINS socket outlet with a protective washing connection.

3. Where the MAIN5 plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

1. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EUI) and your national law.

This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effi client use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city offi ca, or your household waste collection service.

LEGAL DISCLAIMER

MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specific citions, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information regarding MUSIC Group's Limited Warranty, please see complete details online at music group.com/warranty.

BESCHRÄNKTE GARANTIE

Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further information about this or any other product, please visit our website at turbosound.com.

Unpacking the Loudspeaker

After unpacking the unit, please check carefully for damage. If damage is found, please notify your supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future return shipment.

System Requirements

TPA122, TPA152, TPZ122 and TPZ152 are switchable passive / bi-amp 2-way loudspeakers. Passive operation (full range or with a subwoofer) requires 1 amplifier channel and 1 controller channel. The input signal is divided between the low-frequency and high-frequency drivers internally with a passive crossover.

Bi-amp operation (full range or with a subwoofer) requires 2 amplifier channels and 2 controller channels, one for low frequencies and one for high frequencies. The input signal is divided between the low frequency and high frequency driver in the controller and the individual amplified signals are fed to the speaker input.

TPZ153 is a switchable bi-amp / tri-amp 3 way loudspeaker.

Bi-amp operation (full range or with a subwoofer) requires 2 amplifier channels and 2 controller channels, one for low frequencies and one for mid-high frequencies. The input signal is divided between the low frequency and mid-high frequency drivers in the controller and the individual amplified signals are fed to the speaker input. The signals are then divided again between the mid and high frequency drivers internally with a passive crossover.

Tri-amp operation (full range or with a subwoofer) requires 3 amplifier channels and 3 controller channels, one for low frequencies, one for mid frequencies, and a third for high frequencies. The input signal is divided between the low frequency, mid frequency, and high frequency drivers in the controller and the individual amplified signals are fed to the speaker input.

Correct controller settings for all horn variants and operation with subwoofers can be downloaded from the website, and are also available as presents for the LMS series controllers.

To avoid wasting amplifier power, you should use heavy-duty speaker cable with a minimum wire size of 1.5 mm ^2 (16 AWGI, and preferably 2.5 mm ^2 (14 AWG) for longer runs. For extreme cable lengths, be aware of cable impedance and resistive losses. Always observe the correct polarity.

EN

Amplifi er Considerations

The TPA and TPZ series loudspeakers are optimized for use with the TURBOSOUND T series amplifiers with the LMS series controllers. A full range of DSP settings to suit any configuration are provided for download on the TURBOSOUND website. The use of third party amplification and processing is only advised using the matrix of manual settings as well as the limiter calculator provided on the TURBOSOUND website. The TPA and TPZ series loudspeaker enclosures should be driven by high quality power amplifiers designed for true professional use. Power amplifiers should be capable of delivering long term broadband power equal to half the loudspeaker's peak power rating at its stated nominal impedance. The use of underpowered amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters, crossovers and equalisation points must be set in accordance with the settings provided on the TURBOSOUND website. This will ensure the optimum sound quality and long-term reliability as well as protection from damage.

Neutrik speakON* NL4 locking input connector(s) and 4-way barrier strip(s) are provided, allowing options for input and link, passive, bi-amp and tri-amp operation.

Model TPA122 TF132 TP122 TP162

Motor Passive Clamp

LF Clamp

HF Passive Clamp

LF Clamp

HF Passive Clamp

LF Clamp

HF Passive Clamp

LF Clamp

HF Passive Clamp

LF Clamp

HF Clamp

LF Clamp

HF Clamp

Impedance

80

80

60

80

80

50

80

80

60

80

80

60

Minimum Amplifier

Continuous RMS

500 W

500 W

40 W

500 W

500 W

40 W

600 W

600 W

75 W

650 W

750 W

Pavator

Park

2000 W

2000 W

400 W

2000 W

2000 W

400 W

2400 W

2400 W

750 W

2600 W

750 W

Model		TPZ163
Mode		Di-amp LF	Di-amp MFHF	Tri-amp LF	Tri-amp MF	Tri-amp HF
Impedance		8Ω	8Ω	8Ω	8Ω	8Ω
Minimum Amplifier Power	Continuous RMS	800 W	200 W	950 W	200 W	75 W
	Peak	2600 W	800 W	2600 W	800 W	750 W

Connections

Models: TPA122, TPA152, TPZ122, TPZ152

Motor	Back Panel	Connector	Internal Schematic
Passive		speakON* NL4Barrier Strip	NLC 1:1>Input/2>Line 2>Barrier 1:1>Strip 2>Input/2>Line 2>HF LFF LF
Bi-Amp		speakON* NL4Barrier Strip	NLC 1:1>Input/2>Line 2>Barrier 1:1>Strip 2>Input/2>Line 2>HF LF

Model TPZ153

Mode	Connector	Internal Schematic
BI-Amp		[377]
		Barrier Strip
Tri-Amp		Barrier Strip

EN

12 TPA/TPZ series Quick Start Guide

EN

Mounting and Fixing

TPA and TPZ series cabinets are designed with multiple internal rigging points to suit many possible mounting methods in permanent installations. The graphic below shows the assembly of the optional mounting bracket (TPA122-WB and TPA152-WB).

Technical diagram of a device rear panel with numbered components and directional arrows indicating motion or force vectors.

ITEM QTY COMPONENT
1 2 MILL x 45 screw
2	2	F
3 2 Friction washer
4 2 Rotate lock screw
5	2	S
6	1	W

1	a	t
p	r	i
a	l	l

Wall Brackets

1. Remove the M10 blanking bolts from the speaker. The bracket will be mounted to these points.
2. Install the wall plate in the venue using the appropriate fi xings (not supplied).
3. Lift the speaker to the bracket and attach with the supplied M10 bolts and friction washers.
4. Set the desired speaker angle and insert the 2 locking screws.
5. For added precaution and where required by local standards, install an M10 threaded eyebolt in the back of the speaker, then connect a properly-rated safety cable from

The TPZ153-FK fly kit is also available for suspension of 3 TPZ153 models. Array angles from 50 degrees to 90 degrees can be chosen in 5 degree increments. The fly kit comprises an upper and lower fly plate, 4 eyebolts and M10 fixings required for installation. See turbosound.com for more information.

Simple line drawing of a rectangular device with a black screen and mounting bracket (no text or symbols)

Suspending with Eyebolts

TPA and TPZ cabinets can be suspended using optional eyebolts coupled to the internal rigging points provided on the top, bottom and sides and back. The simplest method is to use the two rigging points on the top and a single pull-back rigging point in the centre of the rear panel.

Remove the appropriate countersunk screws and replace them with shoulder eyebolts, which must have a thread length of at least 18 mm. Use the rear rigging point to angle the cabinet for optimum room coverage. Cabinets may be hung upside down if required.

IMPORTANT NOTE: The mounting of a permanently installed sound system may be dangerous unless undertaken by qualified personnel with the

required experience and certification to perform the necessary tasks. Walls, floors or ceilings must be capable of safely and securely supporting the actual load. The mounting accessory used must be safely and securely fixed both to the loudspeaker and to the wall, floor or ceiling.

When mounting rigging components on walls, floors or ceilings, ensure that all fixings and fasteners used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and composition of walls and ceilings, all need to be taken into account when determining whether a particular fixing arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required, must be of an appropriate type, and must be fitted and used in accordance with the maker's instructions.

The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly, can potentially expose persons to serious health risks and even death. In addition, please ensure that electrical, mechanical and acoustic considerations are discussed with qualified and certified (by local state or national authorities) personnel prior to any installation or flying.

Make sure that speaker cabinets are set up and flown by qualified and certified personnel only, using dedicated equipment and original parts and components delivered with the unit. If any parts or components are missing please contact your dealer before attempting to set up the system.

Be sure to observe the local, state and other safety regulations applicable in your country, MUSIC Group, including the MUSIC Group companies listed on the enclosed "Service Information Sheet", assumes no liability for any damage or personal injury resulting from improper use, installation or operation of the product. Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and stable condition. Make sure that, where the speaker is flown, the area underneath the speaker is free of human traffic. Do not fly the speaker in areas that can be entered or used by members of the public.

Speakers create a magnetic field, even if not in operation. Therefore, please keep all materials that can be affected by such fields (discs, computers, monitors, etc) at a safe distance. A safe distance is usually between 1 and 2 metres.

EN

Technical Specifications

TPA152/64 (WH) TPA152/95 (WH) TPA122/64 (WH) TPA122/95 (WH) TPA122/00 (WH) TPZ153/64 TPZ152/64 TPZ122/64

System
Frequency response	43 Hz - 18 kHz - 3 dB37 Hz - 20 kHz - 10 dB	43 Hz - 18 kHz +3 dB37 Hz - 20 kHz - 10 dB	45 Hz - 18 kHz - 3 dB49 Hz - 20 kHz - 10 dB	45 Hz - 18 kHz +3 dB40 Hz - 20 kHz - 10 dB
Nominal dispersion	80° H x 40° V @ 6 dB points, rotatable	90° H x 50° V @ 6 dB points, rotatable	69° H x 40° V @ -6 dB points, rotatable	90° H x 50° V @ -6 dB points, rossable
Directivity factor (Q)	18.3 10.2 18.3 10.4 5	18.3	18.3
Directivity index IDII	12.6 10.2 12.6 10.2 7	12.6	12.6
Power handling IECI
Passive	500 W continuous,2,000 W peakLF: 500 W continuous,2,000 W peakHF: 40 W continuous,100 W peak	600 W continuous,2,000 W peakLF: 500 W continuous,2,000 W peakHF: 40 W continuous,100 W peak	500 W continuous,2,000 W peakLF: 500 W continuous,2,000 W peakHF: 40 W continuous,100 W peak	500 W continuous,2,000 W peakLF: 500 W continuous,2,000 W peakHF: 40 W continuous,100 W peak
Qi amp
Tri-amp	—	—	—	—
Sensitivity	97 dB (1 W @ 1 ml)	97 dB (1 W @ 1 m2)	97 dB (1 W @ 1 m2)	97 dB (1 W @ 1 ml)
Maximum SPL
Passive	124 dB continuous, 130 dB peakLF: 124 dB continuous, 130 dB peakHF: 122 dB continuous, 128 dB peak	124 dB continuous, 130 dB peakLF: 124 dB continuous, 130 dB peakHF: 122 dB continuous, 128 dB peak	124 dB continuous, 130 dB peakLF: 124 dB continuous, 130 dB peakHF: 122 dB continuous, 128 dB peak	124 dB continuous, 130 dB peakUF: 124 dB continuous, 130 dB peakHF: 122 dB continuous, 128 dB peak
Tri-amp	—	—	—	—
Impedance
Passive	8 ΩLF: 8 ΩHF: 8 Ω	8 ΩLF: 8 ΩHF: 8 Ω	9 ΩLF: 8 ΩHF: 6 Ω	9 ΩLF: 8 ΩHF: 6 Ω
Bi-amp
Tri-amp	—	—	—	—
Crossover type	Passive / Bi amp, switchable	Passive / Bi amp, switchable	Passive / Bi amp, switchable	Passive / Bi amp, switchable
Components	1 x 15" (194 mmol) LF drive1 x 1" 125 mmHF compression driver	1 x 15" (264 mmol) LF driver1 x 1" (25 mmol)HF compression driver	1 x 12" (218 mmol) LF driver1 x 1" (25 mmol)HF compression driver	1 x 12" (186 mmol) LF driver1 x 1" (25 mmol)HF compression driver

Enclosure
Connectors	1 x Neutrik speckON® NLD, 1 x barrier strip terminals	1 x Neutrik speckON® NLD, 1 x barrier strip terminals	1 x Neutrik speckON® NLD, 1 x barrier strip terminals	1 x Neutrik speckON® NLD, 1 x barrier strip terminals
Wiring
Passive	Pins 1+/-1 input, pins 2+/-2 link	Pins 1-/-1 input, pins 2+/2- link	Pins 1+/-1 input, pins 2+/2- link	Pins 1+/-1 input, pins 2+/2- link
Bi-amp	Pins 1+/1-LF, pins 2+/2-HF	Pins 1+/1-LF, pins 2+/2-HF	Pins 1+/1-LF, pins 2+/2-HF	Pins 1+/1-LF, pins 2+/2-HF
Tri-amp	—	—	—	—
Dimensions (HWD)	781 x 419 x 503 mm(33.7 x 16.5 x 18.8")	781 x 419 x 503 mm(36.7 x 16.5 x 18.8")	711 x 368 x 458 mm(18.0 x 14.5 x 18.0")	711 x 368 x 458 mm(28.0 x 14.5 x 18.0")
Net weight	20.0 kg 69 lbs	27.0 kg 69.4 lbs	23.8 kg 52.4 lbs	23.3 kg 51.3 lbs
Construction	15 mm (4",/b" birch plywood)	15 mm (2",/b" birch plywood)	15 mm (4",/b" birch plywood)	15 mm (4",/b" birch plywood)
Finish	Semi-matt black paint (white optional)	Semi-matt black paint (white optional)	Semi-matt black paint (white optional)	Semi-matt black paint (white optional)
Grille	Powder coated perforated steel	Powder coated perforated steel	Powder coated perforated steel	Powder coated perforated steel
Flying hardware	M10 x 15 points	M10 x 15 points	M10 x 15 points	M10 x 15 points
Accessories
	TPA152-WB wall bracket PRAGUE 15°	TPA152-WB wall bracket PRAGUE 15°	TPA122-WB wall bracket PRAGUE 12°	TPA122-WB wall bracket PRAGUE 12°

45 Hz - 18 kHz / 3 dB40 Hz - 20 kHz - 10 dB	45 Hz - 20 kHz / 3 dB38 Hz - 20 kHz - 10 dB	41 Hz - 18 kHz / 3 dB35 Hz - 20 kHz - 10 dB	43 Hz - 18 kHz / 3 dB37 Hz - 20 kHz - 10 dB
100° H X 100° V @ 6 dB points, rotatable	60° H x 40° V @ 8 dB points, rotatable	60° H X 40° V @ 6 dB points, rotatable	60° H X 40° V @ 6 dB points, rotatable
500 W continuous, 2,600 W peakLF: 500 W continuous, 2,600 W peakHF: 40 W continuous, 160 W peak—	—LF: 650 W continuous, 2,600 W peakMHF: 200 W continuous, 600 W peakLF: 650 W continuous, 2,600 W peakHF: 200 W continuous, 300 W peakHF: 75 W continuous, 300 W peak	650 W continuous, 2,600 W peakLF: 650 W continuous, 2,600 W peakHF: 75 W continuous, 300 W peak—	600 W continuous, 2,400 W peakLF: 800 W continuous, 2,400 W peakHF: 75 W continuous, 300 W peak—
97 dB (1 W @ 1 m2)	LF: 97 dB (1 W @ 1 m2)MF: 100 dB (1 W @ 1 m2)HF: 103 dB (1 W @ 1 m2)	97 dB (1 W @ 1 m2)	98 dB (1 W @ 1 m2)
124 dB continuous, 130 dB peakLF: 124 dB continuous, 130 dB peakHF: 122 dB continuous, 126 dB peak—	—LF: 125 dB continuous, 131 dB peakMHF: 126 dB continuous, 134 dB peakLF: 129 dB continuous, 131 dB peakMF: 130 dB continuous, 136 dB peakHF: 128 dB continuous, 134 dB peak	125 dB continuous, 131 dB peakLF: 125 dB continuous, 131 dB peakHF: 128 dB continuous, 134 dB peak—	124 dB continuous, 130 dB peakLF: 124 dB continuous, 133 dB peakHF: 126 dB continuous, 134 dB peak—
9ΩLF: 9ΩHF: 6Ω—	LF: 9ΩMHF: 8ΩLF: 8ΩMF: 8ΩHF: 6Ω	6ΩLF: 8ΩHF: 8Ω—	8ΩLF: 8ΩHF: 8Ω—
Passive / Bi amp, switchable	Bi amp / ti amp switchable	Passive / Bi amp, switchable	Passive / Bi amp, switchable
1 x 12" (≥15 mm) LF driver1 x 11" (≥5 mm) HF compression driver	1 x 15" (≥64 mm) LF driver1 x 8" (≥200 mm) HF driver1 x 14" (≥6 mm) HF compression driver	1 x 15" (≥64 mm) LF driver1 x 14" (≥6 mm) HF compression driver	1 x 12" (≥16 mm) LF driver1 x 14" (≥6 mm) HF compression driver

1 x Neutrik speckON® NLL, 1 x barrier strip terminals	2 x Neutrik speckON® NLL, 2 x barrier strip terminals	1 x Neutrik speckON® NLL, 1 x barrier strip terminals	1 x Neutrik speckON® NLL, 1 x barrier strip terminals
Pins 1+ / 1-input, pins 2+ / 2-link		Pins 1+ / 1-input, pins 2+ / 2-link	Pins 1+ / 1-input, pins 2+ / 2-link
Pins 1+ / 1-LF, pins 2+ / 2-HF	Pins 1+ / 1-LF, pins 2+ / 2-MHF, pins 3+ / 3- and pins 4+ / 4-link	Pins 1+ / 1-LF, pins 2+ / 2-HF	Pins 1+ / 1-LF, pins 2+ / 2-HF
—	Pins 1+ / 1-LF, pins 2+ / 2-MF, pins 3+ / 3-HF, pins 4+ / 4-Link
711 x 368 x 458 mm (26.0 x 14.5 x 15.0")	997 x 599 x 656 mm (38.0 x 22.0 x 25.0")	781 x 419 x 503 mm (30.7 x 15.5 x 18.0")	711 x 368 x 456 mm (28.0 x 14.5 x 16.0")
232 kg (51.1 lbs)	433 kg (95 lbs)	26.0 kg (69.0 lbs)	23.4 kg (61.5 lbs)
15 mm FW/21 birch plywood	15 mm FW/21 birch plywood	15 mm FW/21 birch plywood	15 mm FW/21 birch plywood
Semi-matt black paint white optional	Semi-matt black paint	Semi-matt black paint	Semi-matt black paint
Powder-coated perforated steel	Powder-coated perforated steel	Powder-coated perforated steel	Powder-coated perforated steel
M10 x 15 paints	M10 x 13 paints	M10 x 15 paints	M10 x 15 paints
TPA122-WB wall bracket PRAGUE 12"	TPZ163 FK	TPA152-WB wall bracket PRAGUE 15"	TPA122-WB wall bracket PRAGUE 12"

16 TPA/TPZ series Quick Start Guide

EN

Other important information

Important information

1. Register online. Please register your new MUSIC Group equipment right after you purchase it by visiting turbosound.com. Registering your purchase using our simple online form helps us to proceed your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your MUSIC Group Authorized Reseller not be located in your vicinity, you may contact the MUSIC Group Authorized Fuller for your country listed under "Support" at turbosound.com. Should your country not be listed, please check if your problem can be dealt with by our "Online Support" which may also be found under "Support" at turbosound.com. Alternatively, please submit an online warranty claim at turbosound.com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

EN