UVTube Slim - Lighting Eurolite - Free user manual and instructions

USER MANUAL UVTube Slim Eurolite

USER MANUAL Uv-Tube Complete Set CAUTION! Keepthisdeviceawayfromrainandmoisture!Neveropenthehousing!For your own safety, please read this user manual carefully before you initially start-up.Every person involved with the installation, operation and maintenance of this device has to- be qualified- follow the instructions of this manual- consider this manual to be part of the total product- keep this manual for the entire service life of the product- pass this manual on to every further owner or user of the product- download the latest version of the user manual from the Internet INTRODUCTION Thank you for having chosen a EUROLITE UV-Tube Complete Set. If you follow the instructions given in thismanual, we are sure that you will enjoy this device for a long period of time.Unpack your UV-Tube Complete Set. SAFETY INSTRUCTIONS CAUTION! Becarefulwithyouroperations.Withadangerousvoltageyoucansufferadangerouselectricshockwhentouchingthewires!This device has left our premises in absolutely perfect condition. In order to maintain this condition and toensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warningnotes written in this user manual.Important:Damages caused by the disregard of this user manual are not subject to warranty. The dealerwill not accept liability for any resulting defects or problems.If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch iton immediately. The arising condensation water might damage your device. Leave the device switched offuntil it has reached room temperature.Make sure that the available voltage is not higher than stated on the technical sticker.00027046.DOC, Version 1.3 11/27 Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time. Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the device must be disconnected via the mains. If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device should only be removed by a specialist. There must never enter any liquid into power outlets, extension cords or any holes in the housing of the device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced insulation can cause mortal electrical shock. There must never be any objects entering into the device. This is especially valid for metal parts. If any metal parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries. This device falls under protection-class II and features a protective insulation. During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective. Caution: During the operation, high ultraviolet radiation is emitted around the device! Caution: During the operation, the housing becomes very hot. Do not switch the device on and off in short intervals as this would reduce the lamp’s life. HEALTHHAZARD! Neverlookdirectlyintothelightsource,assensitivepersonsmaysufferan epilepticshock(especiallymeantforepileptics)! Keep away children and amateurs! Never leave this device running unattended. OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects. This product is only allowed to be operated with an alternating voltage of 230 V, 50 Hz and was designed for indoor use only. Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. Never put any liquids close to the device. Should any liquid enter the device nevertheless, disconnect from mains immediately. Please let the device be checked by a qualified service technician before you operate it again. Any damages caused by liquids having entered the device are not subject to warranty! Do not shake the device. Avoid brute force when operating the device.00027046.DOC, Version 1.312/27When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, oisture or dust. There should not be any cables lying around. You endanger your own and the safety ofothers!This device must never be operated or stockpiled in sourroundings where splash water, rain, moisture or fogmay harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electricalshocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet nd is installed in a distance of 0.5 meters between smoke machine and device. The room must only besaturated with an amount of smoke that the visibility will always be more than 10 meters.The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation(particularly in cars) and heaters.The relative humidity must not exceed 50 % with an ambient temperature of 45° C.This device must only be operated in an altitude between -20 and 2000 m over NN.Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect thedevice during thunderstorms.The symbol ---m determines the minimum distance from lighted objects. The minimum distance between light-output and the illuminated surface must be more than 0.5 meters. The housing must never touch surrounding surfaces or objects. The maximum ambient temperature T

= 45° C must never be exceeded. Operate the device only after having become familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation! Never use solvents or aggressive detergents in order to clean the device! Rather use a soft and damp cloth. Please use the original packaging if the device is to be transported. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short- circuit, burns, electric shock, etc. The device should not be installed in areas where persons may walk by or be seated. If UV-tubes are to be installed in public areas, then devices with a protective grille must be used. INSTALLATION Installing/Replacing the lamp DANGERTOLIFE! Onlyinstallthelampwiththedeviceswitchedoff!Unplugfrommainsbefore!Thelamphastobereplacedwhenitisdamagedordeformedduetotheheat! CAUTION! Before replacing the lamp, unplug mains lead and let the lamp cool down (approx. 5 minutes).00027046.DOC, Version 1.3 13/27 During the installation do not touch the glass-bulbs bare-handed! Please follow the lamp manufacturer's notes! Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the device was not designed for. Damages caused by non-observance are not subject to warranty.

uring the operation, the lamp reaches temperatures of up to 80° C. UV illuminants are hazardous waste which needs to be disposed of appropriately. Please dispose of the unusable UV illuminants in accordance with the current legal regulations. Procedure: Step 1: Press the buttons together on one end of the fixture and pull this end out a few centimeters. Step 2: If replacing the tube lamp, remove the old lamp from the socket. Step 3: Insert the new tube lamp into the lamp-socket and carefully push the end back into place. Attachment Before attaching the device, make sure that the installation area can hold a minimum point load of 10 times the device's weight. The device must only be installed absolutely planar at a vibration-free, oscillation-free and fire-resistant location. Make sure that the device is installed absolutely planar by using a water-level. The device must be installed out of the reach of people. The device must always be installed via all fixation holes. Do only use appropriate screws and make sure that the screws are properly connected with the ground. The durability of the installation depends very much on the material used at the installation area (building material) such as wood, concrete, gas concrete, brick etc. This is why the fixing material must be chosen to suit the wall material. Always ask a specialist for the correct plug/screw combination indicating the maximum load and the building material. Procedure: Step 1: On the baseplate, there are holes for the installation. Step 2: Hold the baseplate onto the location where the device is to be installed. Step 3: Mark the boreholes with a pen or a suitable tool. Step 4: Drill the holes and fix the screws. Step 5: Install the device onto the screws. DANGERTOLIFE! Beforetakingintooperationforthefirsttime,theinstallationhastobeapprovedbyanexpert! OPERATION After you connected the device to the mains, the UV-tube lamp needs 3-4 minutes warm-up time until it reaches full lighting output.00027046.DOC, Version 1.314/27

CLEANING AND MAINTENANCE

Disconnectfrommainsbeforestartingmaintenanceoperation! DANGERTOLIFE! We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use alcohol or solvents! There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by authorized dealers. Should you need any spare parts, please use genuine parts. Should you have further questions, please contact your dealer. TECHNICAL SPECIFICATIONS

: 45° C Maximum housing temperature T