979659 - Lawn mower Westfalia - Free user manual and instructions

USER MANUAL 979659 Westfalia

• Please read this manual carefully and use the device only according to this manual.

• Dispose of used packaging material carefully or store it out of the reach of children. There is a danger of suffocation!

• Persons with limited physical, sensorial or mental abilities are not allowed to use the device, unless they are supervised and briefed for their safety by a qualified person.

• The hair clipper and beard trimmer is not a toy and does not belong in the hands of children. Keep out of the reach of children.

• Make sure that the available mains voltage corresponds to the information on the type plate of the charger.

• Do not place the device where it can fall or be pulled into the sink or bathtub. Do not use the device in the shower or bath.

• Do not touch the connected charger with wet hands.

• Do not run the cable over hot surfaces or sharp edges.

• Only charge and operate the hair clipper and beard trimmer with the included power pack and only use the power pack to charge and operate the hair and beard trimmer.

• The product may not be exposed to extreme temperatures, strong vibrations or strong mechanical stress.

• Should the unit become damaged do not use it any further and have it repaired by a professional or contact our customer service. Do not disassemble the unit or try repairing it yourself.

Batteries do not belong in the household garbage. For battery disposal please check with your local council.

SAFETY NOTES8 Charging the Hair Clipper and Beard Trimmer Connect the power mains adaptor (7) to a wall socket and to the charging socket on the clipper. The LED indicator light (3) will light up red to indicate the unit is charging. Charging will take approximately 1.5 hours and the LED indicator light will turn blue once the charge is complete. There will be more than 1 hour of running time. The charger must not be used in damp rooms. The hair clipper and beard trimmer can be operated during the charging process. Before Clipping or Trimming Inspect the clipper to make sure that it is free from hair and dirt. Before cutting. The Hair must be dry before cutting. Always comb the hair so it is tangle free and dry. Attaching a Comb Unlock the mounting slide with the slide (4). Fully retract the mounting slide for the comb (8) with the adjustment wheel (2). Place the comb over the front of the clipper and push down the mounting latch (5) until it engages with an audible click. Removing a Comb Fully retract the mounting slide for the comb (8) with the adjustment wheel (2) and lock it in position with the slider (4) on the underside of the clipper. Then push the mounting latch forward and away from the machine with your finger until it disengages. Adjusting the trim Length The comb assembly can be extended and retracted by turning the Adjustment wheel (2). Make sure you lock the comb assembly in place with the slider (4) on the underside of the clipper. Operation Slide the ON/OFF Switch (1) forward to turn on the clipper. Slide the switch back to turn off the clipper. After each Use

• Make sure the clipper is switched off.

• Gently brush the remaining hairs away from the comb and trimmer blade. OPERATION9 Cleaning and Maintenance Your clipper is fitted with high quality ceramic blades and stainless steel blades that are permanently lubricated. To ensure long lasting performance of your clipper, clean the blade assembly regularly. To detach the blade assembly (6), first remove the comb as described above and then remove the blade assembly. To remove the blade assembly, place your thumb against the underside of the blade assembly (white ceramic blade) and force the assembly forward until it releases with an audible click. Be careful not to let the blade assembly fly off. Rinse the blade assembly under running water and remove all hair stuck between the blades. To reattach the blade, hook the blade assembly into the horseshoe-shaped top of the blade assembly retainer and press the blades down until they snap into place with an audible click. Do not disassemble the clipper any further, it does not contain any parts serviceable by you. Do not immerse the remaining parts of the clipper besides the blade assembly in liquids of any kind. Also, do not use abrasives or aggressive chemicals to avoid damaging the surfaces. Technical Data Clipper Input: 5 V , 1 A, 5 W Charging Time: 90 min Operating time: 60 min Battery: 1x 3,7 V, 600 mAh, 2,22 Wh, Li-Ion Blades: Stainless Steel, Ceramic Charging Station Input/Outpu: 5 V , 1 A Power Mains Adapter Input: 100-240 V~ 50/60Hz, 0,2 A Output: 5 V , 1 A, 5 W Protection Class: II10 S'il vous plaît noter afin d'éviter des dysfonctionnements, des dommages et des effets néfastes sur la santé les informations suivantes: