HECO Music Style 1000 - Speaker

Music Style 1000 - Speaker HECO - Free user manual and instructions

Find the device manual for free Music Style 1000 HECO in PDF.

📄 44 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice HECO Music Style 1000 - page 7
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type 3-way bass reflex speaker
Brand Heco
Model Music Style 1000
Nominal power (RMS / peak) 160 W / 280 W
Impedance 4 - 8 Ohm
Frequency response 26 - 40 000 Hz
Recommended amplifier power 30 - 280 W
Efficiency (1W/1m) 91 dB
Dimensions (W x H x D) 199 x 1100 x 338 mm
Supplied accessories Metal spikes and rubber spikes
Terminal type 4 screw terminals (bi-wiring/bi-amping possible)
Recommended placement At least 20 cm from rear wall and 30 cm from side walls
Maintenance and cleaning Clean with mild household cleaner, avoid varnishes
Safety Turn off amplifier before connecting/disconnecting cables
Warranty 5 years (first owner)
Compliance Follow recycling instructions at end of life

Frequently Asked Questions - Music Style 1000 HECO

How to connect the Heco Music Style 1000 speakers?
Use good quality speaker cables (≥ 2.5 mm² for lengths < 3 m, ≥ 4 mm² for > 3 m). Strip 10 to 15 mm, twist the ends and tighten the screws. Ensure correct phase: black terminal (-) from speaker to black terminal (-) of amplifier, red terminal (+) to red terminal (+). Always turn off the amplifier before connecting or disconnecting.
What is the best position for stereo speakers?
Place the speakers and your listening position in an equilateral triangle, with the speakers equidistant from you. Keep them away from walls: at least 20 cm from the rear wall and 30 cm from side walls for floorstanders. The tweeters should be at ear height.
How to use bi-wiring or bi-amping?
Remove the metal short-circuit plates between the terminals. For bi-wiring, connect the amplifier to the upper terminals (tweeter) and lower terminals (woofer) with two separate cables. For bi-amping, use two separate amplifiers, one for each pair of terminals. Standard connection uses the plates for a single cable.
What amplifier power is recommended for the Music Style 1000?
The recommended amplifier output power is 30 to 280 W. A too weak amplifier can cause distortion at moderate volume, which is dangerous for the speakers. If you listen loudly, choose an amplifier of at least 280 W.
How to avoid damaging the speakers?
Do not push the tone controls (bass/treble) to maximum as this can destroy the speakers. Lower the volume as soon as you hear distortion. Ensure the amplifier is not overloaded. Check for inaudible signals (very high frequencies) that can damage the tweeters.
How to maintain the Heco Music Style 1000 speakers?
Clean the surfaces with a mild household cleaner. Do not use furniture polish or abrasive products. Use a soft, slightly damp cloth.
What is the warranty on Heco speakers?
Heco offers a 5-year warranty for the first owner, covering material and manufacturing defects. For a claim, contact your dealer. Include the completed warranty card and proof of purchase. Damage due to misuse is not covered.
What to do if a speaker stops working or produces abnormal sound?
First check all connections and phase. If the problem persists, test with another source or amplifier. If the tweeters are out of order at low volume, a technician should check for inaudible signals. Do not attempt repair yourself; contact after-sales service.
Can I use decoupling spikes?
Yes, metal spikes and rubber spikes are supplied. Screw the metal spikes into the sockets under the speaker to isolate from the floor and avoid resonances. For hard floors, use the rubber spikes to avoid damage.
How to recycle the speakers at end of life?
Dispose of the device at an appropriate recycling point. Do not throw it with household waste. Follow local electronic waste regulations.

User questions about Music Style 1000 HECO

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Speaker in PDF format for free! Find your manual Music Style 1000 - HECO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Music Style 1000 by HECO.

USER MANUAL Music Style 1000 HECO

At the end of the product's useful life, please dispose of it at appropriate collection points provided in your country.

Gummispikes Gummispikes

Congratulations on your fine new loudspeakers and thank you very much for choosing HECO! You have made an excellent choice. The high-quality speakers produced by HECO are renowned all over the world.

Please study the instructions and information below carefully before using your new loudspeakers.

GENERAL INFORMATION ABOUT CONNECTING YOUR HECO MUSIC STYLE LOUDSPEAKERS

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent impairment of sound quality, we recommend cables with cross-sections of at least 2.5mm^2 for lengths up to 3m and at least 4mm^2 for lengths above 3m .

Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place the loudspeakers in their planned positions and cut the cables to the right length. The cables for both channels should always be exactly the same length.

Strip 10 - 15mm of insulation from the ends of the cables. Twist the ends – this is much better than tinning them with solder – insert them in the terminals and tighten the terminal screws firmly. (Fig. 1)

For good sound it is imperative that the cables must be connected in such a way that the speakers are "in phase". This means that the black negative terminals on the speakers (-) must be connected to the negative (-) terminals on the amplifier, the red positive (+) speaker terminals to the positive (+) amplifier terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a ridge in the insulation.

Before switching on the system double-check all your connections and make sure that the terminal screws are tight and that there are no short circuits caused by stray wire filaments – this could cause serious damage to your amplifier!

THE HECO MUSIC STYLE LOUDSPEAKERS IN STEREO MODE

In the ideal configuration the speakers and the listening position should form an equilateral triangle. When the left and right speakers are the same distance from the listening position their sound arrives at the same time, resulting in a harmonious, natural music reproduction. (Fig. 2)

There should be a clear line of sight between the loudspeakers and the listening position. Any sound-absorbing or reflecting obstacles in the path will distort the sound. When you install the loudspeakers the following distances should be maintained:

Floorstanders: at least 20~cm away from the rear wall and at least 30~cm from the side walls. This will prevent excessive emphasis of the bass range.

Bookshelf speakers: shelf loudspeakers should also be as free-standing as possible, the distance to the sides and rear to walls and items should be at least 10cm , the tweeters should be located at ear height.

Spikes (floorstanders): you should use the supplied spikes when setting the speakers up. This isolates them from the supporting surface, preventing unpleasant resonance effects. You can choose between metal and hard rubber spikes for the standing speakers. The spikes are screwed into the threaded bushes on the bottom of the speaker.

HECO MUSIC STYLE LOUDSPEAKERS AS A FRONT OR REAR LOUDSPEAKER

The front loudspeakers are positioned at ear height on the left and right as equidistant from the television as possible. The rear loudspeakers are placed at ear height or a little above on the left and right besides or better behind the listening position. (Fig. 3)

HECO MUSIC STYLE 800, 500 - BI-WIRING AND BI-AMPING

Bi-wiring means using separate cables to carry the high and low audio frequencies. Bi-amping takes this idea one step further and uses separate power amplifiers as well as separate cables for high and low frequencies. Bi-amping in particular produces an additional improvement in sound reproduction quality.

The special connection terminals of the MUSIC STYLE loudspeakers support both conventional connection and operation in bi-wiring and bi-amping modes. There are four screw terminals on each speaker. The top pair are for the tweeter (high frequencies), the lower pair for the woofer (low frequencies). The factory-installed metal strips connecting the positive and negative terminals are for conventional 2-wire connection and must be removed for bi-wiring and bi-amping operation. The pictures below show the correct set-up for conventional operation (Fig. 4a), bi-wiring (Fig. 4b) and bi-amping (Fig. 4c).

HECO MUSIC STYLE CENTER 2

The MUSIC STYLE CENTER 2 loudspeaker visually and acoustically ideally matches the other MUSIC STYLE models. The loudspeaker is placed immediately underneath the television set. Otherwise please adhere to the general recommendations outlined in the previous chapters.

HECO MUSIC STYLE SUB 25A

The MUSIC STYLE SUB 25A active subwoofer visually and acoustically ideally matches the other loudspeakers in the MUSIC STYLE series. Please refer to the separate operating instructions supplied with this product.

CONNECTING TO AN AV RECEIVER

Fig. 5 shows the connecting to an AV receiver.

HOW TO AVOID DAMAGE TO YOUR VALUABLE SPEAKERS

All HECO loudspeakers are designed and built for optimum sound reproduction with the tone controls in the central position - i.e. with "linear" amplifier output. Turning up the bass and treble controls too far delivers more power to the woofers and/or tweeters, and at high volumes this can actually destroy the speaker units!

If the output of your amplifier is significantly higher than the rated power handling capacity of your speakers extremely high volumes can physically destroy your speakers. This doesn't actually happen often but you should be aware that it is possible.

Weak amplifiers with low output ratings can actually be more dangerous for your speakers at medium volumes because weak amplifiers may overload much faster than powerful ones and this causes measurable and audible distortion, which is extremely dangerous to your loudspeakers.

Always turn the volume down immediately as soon as you hear distortion! If you like listening to loud music make sure that your amplifier can deliver at least as much power as the speakers' power-handling rating.

Amplifiers, tuners and CD players can all produce inaudible high-frequency signals – and this doesn't only apply to cheap products. If your tweeters fail at low or medium volumes you should have a qualified technician check your system components for dangerous inaudible signals.

MAINTENANCE

The surface is best cleaned with a mild household cleaner. On no account use furniture polish or similar products.

SPECIFICATIONS

Configuration: 3-way bass reflex 2 1/2-way bass reflex

Power-handling capacity: 160 / 280 W 150 / 275 W

Impedance: 4 - 8 ohms 4 - 8 ohms

Frequency response: 26 - 40 000 Hz 27 - 40 000 Hz

Recommended amplifier output: 30 - 280 W 30 - 275 W

Efficiency (1W/1m): 91 dB 91 dB

Dimensions (WxHxD): 199 x 1100 x 338 mm 225 x 1050 x 353 mm

Accessory: Metal spikes Metal spikes

Rubber spikes

Rubber spikes

Configuration: 2-way bass reflex 2-way bass reflex

Power-handling capacity: 80 / 140 W 90 / 150 W

Impedance: 4 - 8 ohms 4 - 8 ohms

Frequency response: 34 - 40 000 Hz 35 - 40 000 Hz

Recommended amplifier output: 20 - 140 W 20 - 150 W

Efficiency (1W/1m): 89 dB 89 dB

Dimensions (WxHxD): 195 x 300 x 277 mm 490 x 169 x 280 mm

Accessory Rubber spikes Rubber spikes

Subject to technical change.

Très cher client,

Impedance: 4-8 Ohm 4-8 Ohms

Bande passante: 34 - 40 000 Hz 35 - 40 000 Hz

Puisance recommandee

COBETbI NO NCKJIIOUeHnIO CNTyAUcN, TPEBvIOuNX PEMOHTA

Bce rpoKorOBopntH ECO hactpoeHbHa Hanlyuwe BocnpOn3BeJeHne B yCNoBnX, KOrda peryIaTOp yOoBn 3Byka HaxoHTcB CpeDHeM NIOJKeHn, T.e. Ha IINHeHOM yAcTke pa60tbl ycInTeJI MoUHOCn. CyueCTBeHHoe NOBIIeHne yOoBn 3Byka npNBoDnT K TOMy, YTO B Obnactn Hn3KnX n/nn BepxHnx TOHO BblJeTcR N36blTOUHa 3Heprn, YTO npN BBICOKoI rPOMKOCTn MOXET npNBecTN K NCKaKeHnIO 3ByaHn.

Ecnn B Baawem pacnopjxehn HaxoHITc ycnntelb, KOtobn 0bnadaet cyuectBeHHO 60nee BBICOKo BbIXoHoi MOsHocTbIO, npeBbIwaioue NacnopTHyIO Harpy3OCHyIO cnOCo6HOCTb KONOHOK, TO TaKo Ype3MepHb IyPoBeHr pOMKOCTN MoKeT npNBecTN K pa3pyHeHIO rPOMKOrOBOpHTeJIa, UTO, Bnpoye, cIyuaeTcBecbMa peDKO.

YcunnteIco CnabIM BbIXODOM, MoryT, Ondako, npedctabTb OnaCHOCTb dNk KOHOK yke npin cpeHne 3Byka, TAK KAK OHN MOyT OKa3aTbcra neperpuyKeHHbIMn HamHOro 6bICTpee, Yem B cnyuae MouNbIX ycunnteIe. Taka neperpuy3ka obycnoBnae OTteTInBO pernctpnpyeMble npnbopamn cblshmbie nckajehn, kpaHne onachble nra BaWero rpomkoROBOpTeJIa.

B cBra3n C 3Tmnpocm o6paatb BHMaHne Ha NCKaKeHna, BO3HnKaIOUe np peryIuPoBaHn 3Byka, n, pRn Heo6xOndmoCTn, HEmdJIeHNO yMeHbSaatb erO ypoBeHb. ToT, KTO IIObNT cNUpaTb, DOnJKeH cIeINTb 3a Tem, YTo6bl ycINITeJIb KaK MOXHO pExe BblDaBaN TaKyO MoUHOCtB, KOTopaM OMOET npNBecTN K nepeRpy3kam B KOJOhkax.

BOBcEM...

ycnHnTeN, TIOHepbI n CD nneepbl - n He ToIbKO B cnUyae HeDoporHX n3deJn - MOryT BocnpOn3BOIDnTB BOCpInHmAmbe I cyXOM BlicOKOaCTOTNbIe KOJIe6aHn. EcI npM mAlom n cpeHem ypoBHX rpOMKoCTn y Bac nponaiaot BlicOKne TOHa, to BaUy cnCTeMy dONJKeH npOBepNT bCneuaJIncT.

yXoI

IobepxHOCTn JpekomeHdyETcA ONUaTb C NOMOuMMyKnx YHNBepCaNbHbIX YNCTaUx CpeDCTB, T. e.HN B KOEM Cnyae He npIMeHrTb NOHTpy dIa Me6eIIN IIN T. n.

TEXHnueCKXAPAKTEPNCIKN

KoHΦnIpyaun: 3 noIocNble "6acpeΦneKc" 2 1/2 noIocNble "6acpeΦneKc"

Harpy3ouhagcnoc6hoctb:160/280Bt150/275BT

IIMpeHaHc:4-8OM4-8OM

YactoTHbI dnaana3OH:26-40000Γu 27-40000Γu

PekomeHdyemam moohoctb ycnntela: 30-280 Bt 30-275 B

Ko3Φ. noJe3Horo DeiCTBnA (1 Bt/1 M): 91 d6

91 AB

TbI (xBxF)

199 × 1100 × 338 MM

225 × 1050 × 353 MM

Ochactka:

MetaJIInueckne uinbl

MetaJIInueckne BinbI

360HHTOBbIe 11nBbI

360HHTOBbIe 1nIbI

KoHfNrgpauzra: 2 noIochblc "6acpeΦJIeKc" 2 noIochblc "6acpeΦJIeKc"

Harpy3ouha cnoocb:80/140Bt 90/150Bt

IIMpeaHc:4-8OM4-8OM

YacToTHbI dHaana3oH: 34 - 40 000 Fc 35 - 40 000 Fu

PekomeHnyemam MOuHocTb ycHnTeJIa: 20-140 Bt 20-150 Bt

Ko3Φ. nOJIe3HOrO IeINCTBnA (1 Bt/1 M): 89 d6

89B

Γa6apntbI (UxBxΓ): 195 x

490 × 169 × 280MM

Ochactka: 36OHIOBbIe WInbI

360HHTOBbIe 1nBbl

Bo3MOxKbI TexHnueckne n3MeHeHHa.

尊敬的HECO用户,

Congratulations! You have made a wise selection in becoming the owner of a HECO HiFi equipment. Due to high quality HECO HiFi products have earned an excellent reputation through the western world. And this high quality standard enables us to grant a 5-years warranty for HECO HiFi products.

The equipments are checked and tested continuously during the entire production process. In case you have problems with your HECO HiFi equipment, kindly observe the following:

  1. The guarantee period commences with the purchase of the component and is applicable only to the original owner.
  2. During the guarantee period we will rectify any defects due to faulty material or workmanship by replacing or repairing the defective part at our discretion. Further claims, and in particular those for price reduction, cancellation of sale, compensation for damages or subsequent damages, are excluded. The guarantee period is not altered by the fact that we have carried out guarantee work.
  3. Unauthorized tampering with the equipment will invalidate this guarantee.
  4. Consult your authorized dealer first, if guarantee service is needed. Should it prove necessary to return the component to the factory, please insure that the component is packed in original factory packing in good condition the quality control card has been filled out and enclosed with the component your enclose your receipt as proof of purchase.
  5. Excluded from the guarantee are: · Illuminates · Wear parts · Shipping damages, either readily apparent or concealed (claims for such damages must be lodged immediately with forwarding agent, the railway express office or post office). · Scratches in cases, metal components, front panels, etc. (You must notify your dealer directly of such defects within three days of purchase.) · Defects caused by incorrect installation or connection, by operation errors (see operating instructions), by overloading or by external force. · Equipments which have been repaired incorrectly or modified or where the case has been opened by persons other than us. · Consequential damages to other equipments. · Reimbursement of cools, without our prior consent, when repairing damages by third parties.

F

Name and address of the dealer/stamp

Käufer/Customer

Name/Name

Straße/Street

PLZ, Ort/City

Land/Country

Kaufdatum/buying date

No warranty without receipt!

HECO®

Lise-Meitner-Str. 9 • D-50059 Pulheim • Germany
Tel. +49 (0) 2234 / 807 - 0 • Fax +49 (0) 2234 / 807 - 399
Internet: http://www.heco-audio.de

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : HECO

Model : Music Style 1000

Category : Speaker