OMEGA C2100S - Juicer

C2100S - Juicer OMEGA - Free user manual and instructions

Find the device manual for free C2100S OMEGA in PDF.

📄 32 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice OMEGA C2100S - page 3
View the manual : Français FR English EN Español ES
Pick your language and provide your email: we'll send you a specifically translated version.
Product typeSlow screw juicer (masticating)
BrandOmega
ModelC2100S
Rated power700 W
Rated voltage120 V~
Rated frequency60 Hz
Maximum continuous extraction time1 minute
Minimum rest interval2 minutes
Number of speeds2 (slow and high)
Feed chuteGiant (large diameter)
Material of bowl and food contact partsBPA-free plastic
Approximate weight5 kg
Approximate dimensions (L x W x H)30 x 20 x 40 cm
SafetySafety lock on lid, motor overheat protection, stop if parts are incorrectly assembled
Reverse function (REV)Yes, to unblock food
Pulp containerIncluded, lockable
Pusher (plunger)Included
CleaningRemovable parts washable with water (max 80°C), do not put in dishwasher
Spare parts availableYes, contact customer service
WarrantyConsult the manufacturer

Frequently Asked Questions - C2100S OMEGA

What to do if the juicer stops during use?
This may be due to overload or overheat protection. Turn off the appliance, unplug it, remove excess ingredients, and let it cool for 20 to 30 minutes before restarting.
Is it normal for the motor to emit an odor the first few times?
Yes, it is normal during first uses. If the odor persists, contact customer service.
Can I wash the parts in the dishwasher?
No, do not wash parts above 80°C and do not put them in the dishwasher, dryer, or microwave. Wash them by hand with water and a cleaning brush.
How to use the reverse function (REV)?
If the auger jams, press the REV button for 2 to 3 seconds. Wait for a complete stop, then press ON to resume extraction.
What is the maximum continuous use time?
Continuous extraction must not exceed 1 minute. After each minute, let the appliance cool for at least 2 minutes before starting again.
Should I remove pits and thick skins from fruits?
Yes, remove pits, hard seeds, thick skins, and hard shells before inserting them into the chute to avoid damaging the appliance.
Why is there too much pulp in my juice?
This may be due to a damaged extraction filter or excess pulp in the central ring. Check and clean the central ring, or replace the filter if necessary.
How to assemble the juicer correctly?
Place the auger into the filter body, then the top cover. Lock by lifting the safety latch and pushing it toward the cover button. The appliance only works if the latch is properly in place.
What to do in case of vibration or abnormal noise?
Check that the filter is properly installed and balanced, that the appliance is on a stable surface, and that there are not too many ingredients. Correct these points and restart.
Is the appliance equipped with surge protection?
The appliance is designed for a rated voltage of 120 V~. Use it only on a grounded outlet. In case of voltage variation, the motor may be damaged.

User questions about C2100S OMEGA

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Juicer in PDF format for free! Find your manual C2100S - OMEGA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. C2100S by OMEGA.

USER MANUAL C2100S OMEGA

Important safeguards 3

Parts and functions 6

Directions for use 7

Maintenance 9

Safety index 10

Troubleshooting 10

French 11

Spanish 21

Omega®

THANK YOU!

CONGRATULATIONS on the purchase of your new Omega.

At Omega, we strive to develop technologically advanced machines that help deliver nutrition and flavor of the highest kind and closest to nature's purest form. We are driven by you, our brand supporters. Your enthusiasm helps us continue to reinvent and renew our line of juicers, high speed blenders and beverage equipment. Our team at Omega thanks you for supporting us for over 50 years!

Join us on:

INSTAGRAM @OmegaJuicing

FACEBOOK @OmegaJuicers

PRODUCT REGISTRATION, VISIT:

www.omegajuicers.com/omega-warranty-registration

RECIPES, VISIT:

www.omegajuicers.com/recipes

CUSTOMER SERVICE:

Call 1-888-610-0498

visit: www.omegajuicers.com/contact-omega-juicers

After using your Omega, we kindly ask you to rate the machine on www.OmegaJuicers.com

Omega®

IMPORTANT SAFEGUARDS

  1. READ ALL INSTRUCTIONS BEFORE USING.
  2. To protect against electrical shock, do not immerse cord, plug, or main body (motor) in water or other liquid.
  3. Close supervision is necessary when any appliance is used by or near children.
  4. Unplug from outlet before assembling, before taking off parts, before cleaning and when not in use.
  5. Avoid contact with moving parts.
  6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the manufacturer (see warranty) for examination, repair, or electrical or mechanical adjustment.
  7. The use of attachments not recommended or sold by manufacturer may cause fire, electric shock or injury.
  8. Do not let cord hang over edge of table or counter or touch heated surfaces.
  9. Always make sure juicer locking clip is locked when juicer is in operation.
  10. To disconnect, press/switch OFF then remove plug from wall outlet. Make sure the motor stops completely before disassembling.
  11. Do not put your fingers or other objects into the juicer while it is in operation. If food becomes lodged in opening, use food plunger or another piece of fruit or vegetable to push down the lodged food. When this method is not possible, turn off the machine, remove the plug from wall outlet and disassemble juicer to remove the remaining food.
  12. Do not use outdoors.
  13. Do not place on or near a hot gas or electric burner or in a heated oven.
  14. Do not use appliance for anything other than its intended use.
  15. Keep the appliance clean. Refer to the Care & Cleaning instructions in this manual.

All users of this appliance must read and understand these safety precautions before operating.

WARNING

Hazards or unsafe practices which could result in serious personal injury or death.

CAUTION

Hazards or unsafe practices which could result in minor personal injury or appliance damage.

DO NOT PLUG IN OR UNPLUG WITH WET HANDS.

It may cause an electric shock or an injury.

DO NOT USE WITH OTHER THAN RATED VOLTAGE.

It may cause an electric shock, a fire or abnormal performance.

If the voltage is different, it may shorten the life of the motor or cause a failure.

PLUG THE POWER CORD CORRECTLY AND PUSH IT TIGHT IN A WALL SOCKET.

It may cause electric shock or a fire.

IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD. If the power cord is damaged, it may cause electric shock or a fire.

Omega®

NEVER ALTER THE APPLIANCE. ALSO, DO NOT DISASSEMBLE OR REPAIR BY YOURSELF. DO NOT INSERT FINGERS, FOREIGN SUBSTANCES OR OBJECTS SUCH AS PINS INTO GAPS OR HOLES IN THE BASE.

It may cause a fire, an electric shock or a failure. For any technical support, contact the authorized local Customer Care Center.

DO NOT MOISTEN THE BASE OR SPLASH WATER ON THE BASE.

Be careful not to let any liquids or other substances get into the switch on the appliance.

DO NOT OPERATE THE SWITCH WITH WET HANDS.

It may cause electric shock or a fire.

WHEN THE POWER CORD, WIRE IS BROKEN OR DAMAGED OR THE PLUG-IN PART BECOMES LOOSE, DO NOT OPERATE IT.

It may cause an electric shock, a fire or an injury.

FOR SAFETY, MUST DO GROUND CONNECTION DO NOT DO THE GROUNDING ON GAS PIPE, PLASTIC WATER PIPE, TELEPHONE WIRE, ETC.

It could cause an electric shock, a fire, or a malfunction and an explosion. Be sure to use the socket with ground connection.

NEVER DISASSEMBLE BOWL SET DURING OPERATION OR INSERT FINGERS, FOREIGN OBJECTS SUCH AS FORKS, SPOONS ETC. INTO FEEDING TUBE OR JUICE OUTLET.

It may cause an injury, an accident or a failure.

THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR SAFETY.

Children should be supervised to ensure that they do not play with the appliance.

DO NOT OPERATE WITHOUT LOCKING THE PARTS PROPERLY.

It may cause an injury or a failure.

IF A GAS LEAK IS DETECTED, DO NOT PLUG IN THE APPLIANCE'S POWER CORD INTO A POWER OUTLET. IMMEDIATELY VENTILATE THE ROOM BY OPENING A WINDOW, AND ALLOW TO FULLY VENTILATE BEFORE PLUGGING IN THE APPLIANCE.

It may cause an injury or a failure.

IF SCREW ROTATION IS STOPPED IN NORMAL OPERATION, PRESS (REVERSE/REV) BUTTON AND HOLD FOR 2\~3 SECONDS AND THEN AFTER REVERSE OPERATION IS COMPLETELY STOPPED, PRESS (ON) BUTTON AGAIN.

If the problem continues during the operation, the parts may be damaged and performance may be deteriorated due to overheating in a motor. When the problem continues, immediately stop the appliance and contact the local Customer Care Center.

Omega®

NEVER PUT A FINGER, A FORK OR A SPOON ETC. INTO JUICE OUTLET.

It may cause an injury or a failure.

DURING THE OPERATION, DO NOT ATTEMPT TO MOVE THE BASE, DISASSEMBLE PARTS AND TRY TO LOCK THEM.

It may cause an injury or a failure. Any act of event needed, switch off first and unplug the power cord.

WHEN USING THE APPLIANCE, BE CAREFUL IF WEARING A NECKTIE, LONG NECKLACE, SCARF ETC. THAT IT DOES NOT BECOME ENTANGLED IN THE FEEDING TUBE.

It may cause an injury, a failure or a breakage.

PLACE THE APPLIANCE ON A FLAT AND STABLE SURFACE.

It may cause an injury or a failure.

DO NOT OPERATE THE APPLIANCE FOR MORE THAN 30 MINUTES AT A TIME.

It may cause a motor failure due to overheating. Cool it down sufficiently for 5 minutes and operate it again.

DO NOT ALLOW A SEVERE SHOCK TO THE APPLIANCE OR DROP IT.

It may cause an electric shock, a fire or damage

IF THE APPLIANCE GIVES OFF AN UNPLEASANT SMELL OR EXCESSIVE HEATING, SMOKE, STOP USING IMMEDIATELY AND CONTACT THE LOCAL CUSTOMER CARE CENTER.

When using a new appliance, it gives off a smell and the smell disappears naturally over time.

ALWAYS UNPLUG THE APPLIANCE AFTER USE.

WHEN UNPLUGGING THE POWER CORD, MAKE SURE TO HOLD THE POWER CORD.

If holding the wire to unplug, it may cause an electric shock or a fire.

DO NOT WASH AT HIGH TEMPERATURES OF 176°F (80°C) OR MORE.

DO NOT PUT THE APPLIANCE IN A DISHWASHER, A DRYER OR A MICROWAVE ETC.

It may cause a failure or parts deformation.

WHEN MOVING THE APPLIANCE, ENSURE TO MOVE IT HOLDING GRIPS TIGHTLY AT THE BASE BOTTOM WITH BOTH HANDS.

If attempting to hold bowl or the edge of the base, the base falls causing an injury or a failure.

PARTS AND FUNCTIONS

OMEGA C2100S - PARTS AND FUNCTIONS - 1

text_image Labeled diagram of a blender with numbered parts for identification

No. Part Name Function

1 PUSHERWHEN ADDING INGREDIENTS, PUSH AND PRESS THE INGREDIENTS LIGHTLY WITH THE PUSHER DOWN INTO THE HOPPER TO IMPROVE JUICING EFFICIENCY
2 TOPCOVER WITH CHUTECOVERS BLADE AND MOTOR.FEED INGREDIENTS DOWN THE CHUTE
3SCREW PROPELLERSEPERATES JUICE FROM PULP
4-5 FILTER BASKETCATCHES AND EJECTS PULP AND FLOWS JUICE TO DRINKING CONTAINER
6SAFETY LATCHSAFETY FEATURE THAT LOCKS PARTS IN PLACE FOR JUICING
7MOTOR WHEELDRIVER OF CENTRIFUGAL SPIN
8POWER CORDUSED FOR POWERING ON AND OFF
9 BODYELECTRICAL MOTOR IS HOUSED IN THE BODY DO NOT IMMERSE IN WATER
10POWER SWITCHCONTROLS THE POWER OF THE JUICER
11SAFETY SWITCH (MICRO-SWITCH)OVERLOAD PROTECTION
12PULP CONTAINERCATCHES PULP EJECTED DURING JUICING PROCESS

Omega®

DIRECTIONS FOR USE

Clean all parts before using juicer.

This product will not start working before all the parts and components are correctly assembled. Please install and use the product as follows:

OMEGA C2100S - DIRECTIONS FOR USE - 1GEARS·“0” GEAR: STOP·“1” GEAR: LOW-SPEED GEAR·“2” GEAR: HIGH-SPEED GEAR
1 PLACE FILTEFOMEGA C2100S - DIRECTIONS FOR USE - 2OMEGA C2100S - DIRECTIONS FOR USE - 3THE BODY.
2 PLACE SCREOMEGA C2100S - DIRECTIONS FOR USE - 4OMEGA C2100S - DIRECTIONS FOR USE - 5O FILTER BASKET BODY.
3OMEGA C2100S - DIRECTIONS FOR USE - 6PLACE THE TOP COVER WITH CHUTE ONTO THE SCREW PROPELLER AND FILTER BASKET BODY.LOCK IT BY PRESSING DOWN.LIFT THE SAFETY LATCH AND PRESS IT TOWARD TOP COVER BUTTON SOFTLY TO LOCK IT. *** PRODUCT WILL NOT WORK IF SAFETY LATCH IS NOT IN PLACE.
4OMEGA C2100S - DIRECTIONS FOR USE - 71. PLACE THE PULP CONTAINER UNDER PULP CHUTE.2. LOCK THE PULP CONTAINER INTO POSITION.

Omega®

5OMEGA C2100S - Omega® - 1WHEN POWER IS ON MACHINE IS READY TO OPERATE. OPERATION TIME IS ≤1 MINUTE.(BE SURE THE SWITCH IS TURNED OFF BEFORE POWERING ON)
6OMEGA C2100S - Omega® - 2WASH FRUITS OR VEGETABLES AND CUT INTO PIECES. (PLEASE REMOVE PITS, HARD SEEDS, THICK SKIN AND HARD SHELLS.)
7OMEGA C2100S - Omega® - 3PLACE THE JUICE CUP UNDER JUICE OUTLET. THIS PRODUCT DOES NOT COME WITH A JUICE CUP. USE YOUR PREFERRED CUP. START THE SWITCH, YOU CAN CHOOSE SPEED. CONTINUOUS OPERATION TIME SHOULD BE LESS THAN 1 MINUTE.
9OMEGA C2100S - Omega® - 4ADD CUT FRUIT INTO FEED CHUTE. PUSH FOOD DOWN CHUTE USING PUSHER. DO NOT PUSH TOO HARD. IF TOO MUCH PULP IN OUTLET OR IF OVERFLOWING JUICE IN JUICE CUP, SHUT OFF. DO NOT PUT YOUR FINGER OR OTHER OBJECTS INTO FEED INLET!
10OMEGA C2100S - Omega® - 5AFTER FOOD IS COMPLETELY PROCESSED AND THERE IS NO JUICE OUTFLOW, TURN OFF SWITCH, CUT OFF POWER,

UPKEEP AND MAINTENANCE

OMEGA C2100S - UPKEEP AND MAINTENANCE - 11BEFORE WASHING THIS PRODUCT, BE SURE TO TURN OFF THE SWITCH AND DISCONNECT FROM THE POWER SUPPLY.
2WASH AFTER EVERY OPERATION.
3WIPE EXTERIOR WITH WET CLOTH.PLEASE DON'T SUBMERGE THE APPLIANCE INTO WATER OR OTHER LIQUIDS.
4STORE PRODUCT WHEN DRY AND AVOID DIRECT EXPOSURE TO THE SUN'S ULTRAVIOLET RAYS.
5BEFORE STORING THIS PRODUCT, MAKE SURE THAT THIS PRODUCT IS CLEAN AND DRIED.
6REFER TO FOLLOWING STEPS TO WASH DETACHABLE PARTS:
1OMEGA C2100S - UPKEEP AND MAINTENANCE - 2REMOVE PUSHERREMOVE PULP CONTAINER
2OMEGA C2100S - UPKEEP AND MAINTENANCE - 3PULL THE LOCKING HATCH DOWN.OPEN THE TOP COVER.
3OMEGA C2100S - UPKEEP AND MAINTENANCE - 4REMOVE PARTS ABOVE MOTOR HOUSINGPARTS CAN BE WASHED WITH CLEAN WATERUSE A CLEANING BRUSH TO REMOVE PULP FROM FILTER BASKET

Omega®

SAFETY INDEX

RATED VOLTAGE 120V~
RATED POWER700W
RATED FREQUENCY60Hz
CONTINUOUS OPERATING TIME OF JUICING ≤slant 1 MINUTE
SPACING INTERVAL ≥slant 2 MINUTES

TROUBLESHOOTING

Fault phenomenon Cause analysis Cause analysis
UNABLE TO START, PRODUCT FAILS TO WORK.1. POWER PLUG NOT PLUGGED IN2. HEAD COVER INSTALLED INCORRECTLY1. INSERT THE POWER PLUG AGAIN;2. INSTALL HEADCOVER IN PLACE
ELECTRIC MOTOR HAS A ODOR THE FIRST FEW TIMES.THIS IS NORMAL.PLEASE CALL CUSTOMER SERVICE IF THE PRODUCT CONTINUES TO HAVE AN ODOR
STOPS WHILE USING.1. LOW POWER VOLTAGE IS OFF2. EXCESSIVE INGREDIENTS3. PUSH THE ROD WITH EXCESSIVE FORCE4. MOTOR OVERHEAT CONTROL PROTECTION1. CHECK IF POWER IS OFF2. DISCONNECT POWER, TAKE OUT THE SURPLUS INGREDIENTS.3. PUSH THE ROD GENTLY.4. RESTART IT AFTER STOPPING 20-30 MINUTES.
TOO MUCH PULP IN THE JUICE1. JUICE EXTRACTION SCREEN IS DAMAGED.2. TOO MUCH PULP IN THE CENTRAL RING.1. REPLACE THE SCREEN.2. CLEAN THE CENTRAL RING.
ABNORMAL VIBRATION OR LOUD NOISE.1. IMPROPER INSTALLATION OF JUICE EXTRACTION SCREEN OR IN BALANCED INSTALLATION.2. UNSTABLE PLACEMENT OF PRODUCT OR CAME OFF OF FOOT PAD.3. EXCESSIVE INGREDIENTS1. INSTALL JUICE EXTRACTION SCREEN IN PROPER PLACE.2. PLACE PRODUCT STABLY OR INSTALL THE FOOT PAD IN PROPER PLACE.3. DISCONNECT POWER AND TAKE OUT EXCESSIVE INGREDIENTS.
LOW QUANTITY OF JUICE1. TO MUCH PULP IN FILTER BASKET2. PUSHING PUSHER WITH EXCESSIVE FORCE1. CLEAN CENTRAL RING.2. PRESS THE PUSH ROD WITH LESS FORCE.

CONTACT US:

Customer Service: 1-888-610-0498

Online: www.OmegaJuicers.com/contact-omega-juicers

Omega®

CONTENU

Merci 12

Mesures de protection importantes 13

www.omegajuicers.com/omega-warranty-registration

www.omegajuicers.com/recipes

Visitez le site : www.omegajuicers.com/contact-omega-juicers

text_image Labeled diagram of a blender with numbered parts for identification
No Nom de la pièce Fonction
1 PISTONLORSQUE VOUS AJOUTEZ DES INGRÉDIENTS, POUSSEZ ET ENFONCEZ LÉGÈREMENT LES INGRÉDIENTS À L'AIDE DU PISTON DANS LA TRÉMIE D'ALIMENTATION POUR AMÉLIORER L'EFFICACITÉ DE L'EXTRACTION DE JUS
2COUVERCLE SUPÉRIEUR AVEC GOULOTTECOUVRE LA PALE ET LE MOTEUR. ALIMENTEZ LES INGRÉDIENTS DANS LA GOULOTTE
3 HÉLCE À VIS SÉPARE LE JUS DE LAPULPE
4-5 FILTRECAPTURE ET ÉJECTE LA PULPE ET ACHEMINE LE JUS VERS LE CONTENEUR DE BOISSONS
6 LOQUET DE SÉCURITÉDISPOSITIF DE SÉCURITÉ QUI VERROUILLE LES PIÈCES EN PLACE POUR L'EXTRACTION DU JUS
7 ROUE DE MOTEUR ENTRAÎNEUR DE ROTATION CENTRIFUGE
8 COPDON D'ALIMENTATION UTILISÉ POUR METTRE EN MARCHE ET À L'ARRÊT
9 CORPSLE MOTEUR ÉLECTRIQUE EST LOGÉ DANS LE CORPS ET NE DOIT PAS ÊTRE IMMERGÉ DANS L'EAU
10 INTERRUPTEURCONTRÔLE L'ALIMENTATION ÉLECTRIQUE DE L'EXTRACTEUR DE JUS
11INTERRUPTEUR DE SÉCURITÉ (MICRO-INTERRUPTEUR)PROTECTION CONTRE LES SURCHARGES
12 RÉCIPIENT À PULPE CAPTURE LA PULPE ÉJECTÉE PENDANT L'EXTRACTION

Omega®

MODE D'EMPLOI

www.omegajuicers.com/omega-warranty-registration

www.omegajuicers.com/recipes

SERVICIO AL CLIENTE:

Llama al 1-888-610-0498

visita: www.omegajuicers.com/contact-omega-juicers

text_image Labeled diagram of a blender with numbered parts for identification

Por Internet: www.OmegaJuicers.com/contact-omega-juicers

OMEGA C2100S - MODE D'EMPLOI - 1

text_image Omega®

Nourish Your Body

Enrich Your Soul

NOURRISSEZ VOTRE CORPS

www.OmegaJuicers.com

The Legacy Companies, Weston, FL 33331 U.S.A. • 1-888-610-0498

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : OMEGA

Model : C2100S

Category : Juicer