M18 Force Logic 2679750C - Power tool MILWAUKEE - Free user manual and instructions

USER MANUAL M18 Force Logic 2679750C MILWAUKEE

SAFETY WARNINGS WARNING Read all safety warnings, instruc- tions, illustrations and specica- tions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, re and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-oper- ated (cordless) power tool.

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive atmo- spheres, such as in the presence of ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

• Keep children and bystanders away while operat- ing a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi- tions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock. PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the o󰀨-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your nger on the switch or energizing power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and bal- ance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and o󰀨. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for misalignment or binding of moving parts, break- age of parts and any other condition that may a󰀨ect the power tool's operation. If damaged, have the power tool repaired before use. Many ac- cidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations di󰀨erent from those intended could result in a hazard- ous situation.

• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

• Recharge only with the charger specied by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of re when used with another battery pack.

• Use power tools only with specically designated battery packs. Use of any other battery packs may create a risk of injury and re.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a re.3

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact ac- cidentally occurs, ush with water. If liquid con- tacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is dam- aged or modied. Damaged or modied batteries may exhibit unpredictable behavior resulting in re, explosion or risk of injury.

• Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or tem- perature above 265°F (130°C) may cause explosion.

• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specied in the instructions. Charging im- properly or at temperatures outside the specied range may damage the battery and increase the risk of re. SERVICE

• Have your power tool serviced by a qualied repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

• Use tool only as directed. Only trained personnel should operate tool.

WARNING To reduce the risk of arc ash, electric shock and property damage, work on deenergized lines when possible. Tool is not insulated. Should work on energized lines be required, ensure all proper precautions, including those contained in NFPA 70E, have been taken rst.

• Use tool only with MILWAUKEE crimping jaw 49-16-U000 or 49-16-U111, "U" dies, and connectors for which they are rated. Jaws, dies, and connec- tors must be used in an APPROVED COMBINA- TION to achieve a successful operation. Improper combinations can result in a faulty crimp. Electric shock, re, explosion, and property damage could occur.

• Do not use tool without jaws installed. Fingers could be injured.

• Keep hands away from jaws while tool is in use. Fingers could be injured.

• To reduce the risk of injury, wear safety goggles or glasses with side shields when operating or servicing the tool.

• Inspect and discard workpieces with cracks or wear before use. Materials may crack or shatter.

• Follow installation specications as specied in Table A or B using an Approved Combination of jaws, dies, connectors and cables as indicated. Other uses may cause damage to the tool, acces- sories, and workpiece.

• Chemical Burn Hazard. Keep coin cell battery away from children.

Always use common sense and be cautious when using tools. It is not possible to anticipate every situation that could result in a dangerous outcome. Do not use this tool if you do not understand these operating instructions or you feel the work is beyond your capability; contact Milwaukee Tool or a trained professional for additional information or training.

• Maintain labels and nameplates. These carry im- portant information. If unreadable or missing, contact a MILWAUKEE service facility for a free replacement.

WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other masonry products, and

2. Backup release valve

3/0 AWG ORANGE 49-16-U03AC 3/0

Lugs: 2 Splices: N/A

YS, YS-L, YS-T CT & CTL

Lugs: 2 Splices: N/A

Lugs: s: 2 Lugs: 2 Splices: N/A

3/0 AWG RUBY 49-16-U03A 3/0

Lugs: 4 Splices: N/A

Lugs: N/A Splices: 4

Lugs: 5 Splices: N/A

600 MCM BLACK 49-16-U600 * 600

Lugs: 4** Splices: N/A

750 MCM YELLOW 49-16-U750 * 750 4 4

Connections made with tool 2779-20 or 2679-20 with jaw 49-16-U000 or 49-16-U111 and combination of die and connector part numbers in the charts below produce UL classied crimps according to the UL 486A-B standard. Number of crimps is a minimum. Additional crimps would not negatively a󰀨ect the integrity of the connection so long as they are uniformly placed between the intended crimp area of the connector, typically outlined with color bands or knurls. For the latest listing of approvals, visit milwaukeetool.com. Table A - United States + Concentric or Compressed only. * Connections must use jaw 49-16-U111.

• Connections must use jaw 49-16-U111. ** Aluminum wire only.5 Dual Rated Lugs & Splices Anderson Blackburn

Lugs: 2 Splices: N/A

Lugs: s: 2 Lugs: 2 Splices: N/A

3/0 AWG RUBY 49-16-U03A 3/0

Lugs: 4 Splices: N/A

Lugs: N/A Splices: 4

Lugs: 5 Splices: N/A

600 MCM BLACK 49-16-U600 * 600

Lugs: 4** Splices: N/A

3/0 AWG ORANGE 49-16-U03AC 3/0

Lugs: 2 Splices: N/A

YS, YS-L, YS-T CT & CTL

SCSS, SCS, SCL, SCH BCU & BBCU 54504-54523-TB & 54804-54823 Lug Model #'s VHCS & VHCL CTL-2, CTL, CTL-L, LCN YA , YAZ, YA-L, YA-2L, YA-2LN, YA-L-NT, YA-L-2NT, YA-L-TC, YA-L-2TC, YA-2N, YA-TC, YA-2TC CLN, CLND, CLNS, CLW, CLWD, CRA, CRB, CRA-L, CRB-L, CRA-2L, CRB-2L, CSW, CSWS LCA, LCAS LCB, LCC, LCD BLU & BBLU 54104-54123-TB, 54204-54223, 54850BE-54880BE, 54930BE-54923BE Table B - Canada and Mexico

• Connections must use jaw 49-16-U111. Connections made with tool 2779-20 or 2679-20 with jaw 49-16-U000 or 49-16-U111 and combination of die and connector part numbers in the charts below produce UL classied crimps according to the UL 486A-B standard.

• Connections must use jaw 49-16-U111. ** Aluminum wire only. Number of crimps is a minimum. Additional crimps would not negatively a󰀨ect the integrity of the connection so long as they are uniformly placed between the intended crimp area of the connector, typically outlined with color bands or knurls. For the latest listing of approvals, visit milwaukeetool.com.6 Connections made with tool 2779-20 or 2679-20 with jaw 49-16-U000 or 49-16-U111 and combination of die and connector part numbers in the charts below produce UL classied crimps according to the UL 486A-B standard. Number of crimps is a minimum. Additional crimps would not negatively a󰀨ect the integrity of the connection so long as they are uniformly placed between the intended crimp area of the connector, typically outlined with color bands or knurls. For the latest listing of approvals, visit milwaukeetool.com. Wire Size (Code only) Die Color Cat. No. Die Indentation Mark Lugs: Total # of Crimps Splices: # of Crimps per Side Anderson Blackburn

Connections must use jaw 49-16-U111. Dual Rated Lugs & Splices Anderson Blackburn

Lugs: N/A Splices: 2 Lugs: 2 Splices: N/A

Lugs: s: 2 Lugs: 2 Splices: N/A

Lugs: N/A Splices: 4

• Connections must use jaw 49-16-U111. ** Aluminum wire only.7 SYMBOLOGY Volts Direct Current WARNING To reduce the risk of arc ash, electric shock and property damage, work on deenergized lines when possible. Tool is not insulated. Should work on energized lines be required, ensure all proper precautions, including those contained in NFPA 70E, have been taken rst. WARNING Keep hands away from jaws while tool is in use. Fingers could be injured. To reduce the risk of injury, wear safety goggles or glasses with side shields when operating or servicing the tool. Read operator's manual. Underwriters Laboratories, Inc. ASSEMBLY WARNING Recharge only with the charger specied for the battery. For spe- cic charging instructions, read the operator's manual supplied with your charger and battery. Removing/Inserting the Battery To remove the battery, push in the release buttons and pull the battery pack away from the tool. WARNING Always remove the battery pack any time the tool is not in use. To insert the battery, slide the pack into the body of the tool. Make sure it latches securely into place. WARNING Only use accessories specically recommended for this tool. Others may be hazardous. Inserting/Removing the Crimping Jaws

1. WARNING! Remove battery to avoid starting the tool.

2. Remove the locking thumb screw (when used)

from the back of the retaining pin.

3. Push in, then rotate the retaining pin counterclock-

wise 90° . The pin will pop out.

4. Insert the crimping jaws. Line up the center hole

with the retaining pin.

5. Push in the retaining pin, then rotate clockwise

6. Insert and hand tighten the locking thumb screw.

NOTE: Use the locking thumb screw to prevent the retaining pin from being unintentionally loosened. A loose retaining pin may damage the tool.

7. Rotate the jaws to the desired angle.

CAUTION To avoid damage to the tool, do not operate the tool without the retain- ing pin fully inserted and locked into position. Damage to the cylinder may occur. WARNING An incomplete or faulty crimp could cause a re. Use tool only with MILWAUKEE crimping jaw 49-16-U000 or 49-16-U111, "U" dies, and connectors for which they are rated. Jaws, dies, and connectors must be used in an approved combination to achieve a successful operation. Improper combinations can result in a faulty crimp. Electric shock, re, explosion, and property damage could occur. Changing the Dies Inspect dies and connectors before use. Only use properly matched dies and connectors for the crimp- ing jaws. Refer to Table A or B for die/connector compatibility.

1. WARNING! Remove battery to avoid starting the tool.

2. Open jaws by squeezing back of crimping head

3. Snap the appropriate dies into each side of the

crimping jaws. Release the jaws.

4. To remove, open jaws by squeezing back of crimp-

ing head together. Pull out the die release tabs. Pull dies out from crimping jaws. ONE-KEY™ To learn more about the ONE-KEY™ functionality for this tool, go to milwaukeetool.com/One-Key. To download the ONE-KEY™ app, visit the App Store

or Google Play™ from your smart device. ONE-KEY™ Indicator Solid Blue Wireless mode is active and ready to be congured via the ONE-KEY™ app. Blinking Blue Tool is actively communicating with the ONE-KEY™ app. Blinking Red Tool is in security lockout and can be unlocked by the owner via the ONE-KEY™ app. Cutting Jaws (not included) The Crimper is compatible with the following MILWAUKEE cutting jaws. Refer to the cutting jaws' instructions for use. Jaw Type Maximum Capacity 750 MCM Cu/AL Jaws (Cat. No. 49-16-2780) 750 MCM Cu/1000 MCM Al8 OPERATION WARNING To reduce the risk of arc ash, electric shock and property damage, work on deenergized lines when possible. Tool is not insulated. Should work on energized lines be required, ensure all proper precautions, including those contained in NFPA 70E, have been taken rst. Keep hands away from crimping jaws while tool is in use. Fingers could be crushed. Always wear proper eye protection marked to comply with ANSI Z87.1. Crimping Before crimping:

• Inspect the jaws and dies for cracks or other dam- age. Do not use damaged jaws or dies. Contact a MILWAUKEE service facility.

• Ensure retaining pin is properly seated and dies are properly installed.

• Jaws, dies, connectors, and cables must be used in an APPROVED COMBINATION. Improper combinations can result in a faulty crimp.

• Inspect and discard workpieces with cracks or wear before use. Materials may crack or shatter.

• Follow installation specications as specied in Table A or B using an Approved Combination of jaws, dies, connectors and cables as indicated. Other uses may cause damage to the tool, acces- sories, and workpiece.

1. Insert battery pack.

2. Place jaws with installed dies around the connector.

3. Hold tool securely. Press and hold the trigger.

4. When the cycle is complete the tool will switch o󰀨

and the indicator will light. Release the trigger. LED Indicator Denition Solid Green Tool completed the operation and reached full crimping pressure. Solid Red Tool completed the operation but did NOT reach full crimping pressure. Flashing Red Tool did NOT complete the operation. Flashing Red/Green (after Solid Green or Solid Red) Tool has reached its service interval (40,000 crimps). Red/Green ashing will begin after the solid Red or Green indicator for the operation is displayed. MILWAUKEE recommends that the tool be inspected and preventative maintenance completed. Return tool to a MILWAUKEE service facility.

5. Continue crimping according to the instructions

in Table A or B, or the connector manufacturer's installation instructions.

Crimps should be uniformly placed on the barrel of the connector.

Crimps should be reasonably placed within the color bands or knurled area of the connector.

For splices, begin crimping in the center, working outward while alternating sides.

For lugs, begin crimping near the pad, working towards the barrel.

The orientation of the crimp is not critical on seamless barrel connectors, but for best results rotate the tool 180° between crimps.

6. Two LEDs will light the workpiece when the trigger

7. The die identier is pressed into the connector

during the crimp. Backup Release Valve If the jaws need to be opened without completing the cycle, press and hold the backup release valve. Hold tool securely until the cylinder retracts fully. MAINTENANCE WARNING To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the battery pack, charger, or tool, except as pro- vided in these instructions. Contact a MILWAUKEE service facility for all other repairs. Maintaining Tool Keep your tool, battery pack and charger in good repair by adopting a regular maintenance program. Inspect your tool for issues such as undue noise, misalignment or binding of moving parts, breakage of parts, or any other condition that may a󰀨ect the tool operation. Return the tool, battery pack, and charger to a MILWAUKEE service facility for repair. After six months to one year, depending on use, return the tool, battery pack and charger to a MILWAUKEE service facility for inspection. If the tool does not start or operate at full power with a fully charged battery pack, clean the contacts on the battery pack. If the tool still does not work prop- erly, return the tool, charger and battery pack, to a MILWAUKEE service facility for repairs. ONE-KEY™ Refer to the ONE-KEY App for information regarding necessary servicing, such as internal battery life and crimp count. WARNING Chemical Burn Hazard. This device contains a lithium button/coin cell battery. A new or used battery can cause severe in- ternal burns and lead to death in as little as 2 hours if swallowed or enters the body. Always secure the battery cover. If it does not close securely, stop using the device, remove the batteries, and keep it away from children. If you think batteries may have been swallowed or en- tered the body, seek immediate medical attention. Internal Coin Cell Battery An internal coin cell battery is used to facilitate full ONE-KEY™ functionality. To replace the coin cell battery:

1. WARNING! Remove tool's battery to avoid start-

2. Loosen the screw(s) and open the coin cell bat-

3. Remove the old coin cell battery, keep it away from

children, and dispose of it properly.

4. Insert the new coin cell battery (3V CR2032), with

the positive side facing up.

5. Close the battery door and tighten the screw(s)

securely.9 WARNING To reduce the risk of personal in- jury and damage, never immerse your tool, battery pack or charger in liquid or allow a liquid to ow inside them. Cleaning Clean dust and debris from any vents. Keep tool clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean, since certain clean- ing agents and solvents are harmful to plastics and other insulated parts. Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household deter- gents containing ammonia. Never use ammable or combustible solvents around tools. Repairs For repairs, return the tool, battery pack and charger to the nearest authorized service center. ACCESSORIES WARNING Always remove battery pack before changing or removing accesso- ries. Only use accessories specically recom- mended for this tool. Others may be hazardous. For a complete listing of accessories, go online to www.milwaukeetool.com or contact a local distributor. WIRELESS COMMUNICATION For products provided with wireless communication features, including ONE-KEY™: Pursuant to part 15.21 of the FCC Rules, do not modify this product. Modication could void your authority to operate the product. This device complies with part 15 of the FCC Rules and ISED-Canada's license exempt RSS standards. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

SERVICE - UNITED STATES

1-800-SAWDUST (1.800.729.3878) Monday-Friday, 7:00 AM - 6:30 PM CST or visit www.milwaukeetool.com Contact Corporate After Sales Service Technical Support with technical, service/repair, or warranty questions. Email: [e-mail] Become a Heavy Duty Club Member at www.milwaukeetool.com to receive important notications regarding your tool purchases.

Monday-Friday, 7:00 AM - 4:30 PM CST or visit www.milwaukeetool.ca LIMITED WARRANTY USA & CANADA This MILWAUKEE power tool* is warranted to the original purchaser from an authorized MILWAUKEE distributor only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace any part on this power tool which, after examination, is determined by MILWAUKEE to be defective in material or workmanship for a period of ve (5) years after the date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the proof of purchase should be included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents. Normal Wear: Many power tools need periodic parts replacement and service to achieve best performance. This warranty does not cover repair when normal use has exhausted the life of a part including, but not limited to, carriage gears, chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and bumper cover washers. *This warranty does not cover battery packs or all power tools. Refer to the separate and distinct warranties available for those products. The warranty period for the LED in the LED Work Light (49-24-0171) and the LED Upgrade Bulb (49-81-0090) is the lifetime of the product subject to the limitations above. If during normal use the LED or LED Upgrade Bulb fails, the part will be replaced free of charge. Warranty Registration is not necessary to obtain the applicable war- ranty on a MILWAUKEE power tool product. The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at the time warranty service is requested. ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CON- TRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CON- SEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EX- CLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR- RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WAR- RANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. This warranty applies to product sold in the U.S.A. and Canada only. Please consult the ‘Service Center Search’ in the Parts & Service sec- tion of MILWAUKEE’s website www.milwaukeetool.com or call 1.800. SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and non-warranty service on a MILWAUKEE power tool.10 RÈGLES DE SÉCURITÉ GÉNÉRALES

YS, YS-L, YS-T CT & CTL

YS, YS-L, YS-T CT & CTL

Monday-Friday, 7:00 AM - 4:30 PM CST www.milwaukeetool.ca

YS, YS-L, YS-T CT & CTL

YS, YS-L, YS-T CT & CTL