AquaFusion 87320 - Filtered water dispenser HAMILTON BEACH - Free user manual and instructions

Brand	Hamilton Beach
Model	AquaFusion 87320
Product Type	Filtered and flavored water dispenser
Filter Capacity	378 liters (100 gallons) / up to 5 months
Flow Rate	0.57 L/min (0.15 Gal/min)
Operating Temperature	1°C to 38°C
Power Supply	120V ~ 60Hz
Water Reservoir Capacity	Approximately 3 liters (MAX line)
Main Functions	Dispensing filtered water and flavored water (pods)
Replacement Filter	Model 87325
Dishwasher-Safe Removable Parts	Funnel, pod holder, needle holder, cup platform (upper rack)
Maintenance	Unplug before cleaning; water reservoir washable with soapy water
Safety	Sharp needles (caution), polarized plug, automatic shut-off after 3 minutes
Warranty (Canada)	5 years
Warranty (United States)	1 year
Filter Life Indicator	Indicator light (yellow = soon to end, red = replace)
Flavored Water Output Volume	355 ml (12 oz) per cycle
Weight (approx.)	3.5 kg
Dimensions (approx.)	30 x 25 x 35 cm
Repairability	Needle unclogging possible; customer support for parts

Frequently Asked Questions - AquaFusion 87320 HAMILTON BEACH

How to install the water filter for the first time?

Remove the water reservoir, align the arrow on the filter with the one on the base, turn clockwise to lock. Fill with cold water to MAX, replace the reservoir, then rinse the filter by holding the filtered water button for 3 minutes. Repeat twice.

How to dispense flavored water?

Make sure the funnel and pod holder are in place. Open the lid, insert a flavored pod (do not remove the foil seal), close the lid until it clicks. Place a cup of at least 414 ml under the spout and press the Flavor + Filtered button to get 355 ml of flavored water.

What to do if the indicator flashes red three times?

This means the lid is not latched or the removable funnel is not properly installed. Check that the funnel is in place and the lid is closed with an audible click.

How to clean clogged needles?

Unplug the unit. Remove the needle holder by turning counterclockwise. Use a small unfolded paperclip to unclog the needle in the pod holder and the needle in the needle holder. Reinstall the needle holder by turning clockwise.

Why is my dispenser not dispensing water or is the flow weak?

First check that the water filter is in place and the needles are not clogged. If the problem persists, replace the water filter. Also ensure the reservoir has enough cold water.

How to reset the filter life indicator after replacing it?

After installing a new filter, press and hold the Flavor + Filtered and Filtered Water buttons simultaneously for at least 3 seconds. The indicator will flash and then turn off, indicating reset.

Can I use a cup smaller than 414 ml for flavored water?

No, use a cup of at least 414 ml (14 oz) to avoid overflow. The cycle dispenses 355 ml of water, so a smaller container will overflow.

The unit stops after a few minutes, is this normal?

Yes, the unit automatically shuts off after 3 minutes of continuous operation to protect the pump. Wait about 1 minute before restarting.

How to maintain the water reservoir?

Wash the reservoir and its lid with warm soapy water, rinse and dry. Do not use abrasive cleaners. The exterior of the unit can be wiped with a damp cloth.

What type of flavored pods to use?

Use only the flavored pods recommended by Hamilton Beach for the AquaFusion. Do not remove the aluminum foil seal before insertion. Pods are sold separately.

USER MANUAL AquaFusion 87320 HAMILTON BEACH

For recipes, tips and product information.

hamiltonbeach.ca

Exterior view of a modern water dispenser with clear glass and water drop, no visible text or symbols

AquaFusion Filtered and Flavored Water Dispenser

This is not a toy or children's product. This product is not designed or intended for use by children age 12 or younger. Adult supervision is necessary when any appliance is used by or near children.

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

1. Read all instructions.
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning use of the appliance by a person responsible for their safety.
3. Close supervision is necessary when any appliance is used by or near children. Cleaning and user maintenance shall not be made by children without supervision. Children should be supervised to ensure that they do not play with the appliance.
4. To protect against risk of electrical shock, do not put cord, plug, or base assembly in water or other liquid.
5. Turn the appliance off, then unplug from outlet when not in use, before putting on or taking off parts, and before cleaning. To unplug, grasp the plug and pull from the outlet. Never pull from the power cord.
6. Do not operate any appliance with a damaged supply cord or plug, or after the appliance malfunctions or has been dropped or damaged in any manner. Supply cord replacement and repairs must be conducted by the manufacturer, its service agent, or similarly qualified persons in order to avoid

a hazard. Contact Customer Service for information on examination, repair, or adjustment as set forth in the Limited Warranty.

1. The use of attachments including filters or flavor capsules not recommended or sold by the appliance manufacturer may cause fire, electric shock, or injury to persons.
2. Do not use outdoors.
3. Do not let cord hang over edge of table or counter or touch hot surfaces, including stove.
4. Do not place on or near a hot gas or electric burner, or in a heated oven.
5. Do not use appliance for other than intended purpose.
6. Water reservoir is for water only. Do not fill with any other liquid. Do not overfill the water reservoir with water.
7. CAUTION: The machine has two sharp needles that puncture the flavor capsule. One on the needle holder and the other in the capsule holder. To avoid risk of injury, do not put your fingers in the holders or under the lid when closing.
8. Always place the unit on a level, stable, and water-resistant surface.

SAVE THESE INSTRUCTIONS

Other Consumer Safety Information

This appliance is intended for household use only.

WARNING Electrical Shock Hazard: This appliance is provided with a polarized plug (one wide blade) to reduce the risk of electric shock. The plug fits only one way into a polarized outlet. Do not defeat the safety purpose of the plug by modifying the plug in any way or by using an adapter. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, have an electrician replace the outlet.

The length of the cord used on this appliance was selected to reduce the hazards of becoming tangled in or tripping over a longer cord. If a longer cord

is necessary, an approved extension cord may be used. The electrical rating of the extension cord must be equal to or greater than the rating of the appliance. Care must be taken to arrange the extension cord so that it will not drape over the countertop or tabletop where it can be pulled on by children or accidentally tripped over.

To avoid an electrical circuit overload, do not use another high-wattage appliance on the same circuit with this appliance.

Technical Specifications

Filter capacity: 100 gallons (378 liters)/up to 5 months

Rated service flow: 0.15 Gal/min (0.57 L/min)

Minimum temperature: 33°F (1°C)

Maximum temperature: 100°F (38°C)

Performance Data Sheet

The replacement filter model number is 87325.

The system conforms to NSF/ANSI 42, 53, and 401 for the specific performance claims verified and substantiated by test data.

The compounds certified under NSF/ANSI 401 have been deemed as incidental contaminants/emerging compounds. Incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels.

While testing was performed under standard laboratory conditions, actual performance may vary.

While occurring at only trace levels, these compounds can affect the public acceptance/perception of drinking water quality.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Systems that are certified for cyst reduction may be used on disinfected water that may contain filterable cysts.

System and installation shall comply with applicable state and local regulations.

Substance AquaFusion %	Reduction	Influent Concentration (mg/L) %	Reduction Requirement / Maximum Filtered Concentration (mg/L)
NSF Standard 42 – Aesthetic Effects
Chlorine 99% 2.0 mg/L ± 10% ≥ 50%
Particulate Class I particles 0.5 <1 μm	98.6%	minimum 10,000 particles/mL	≥ 85%
NSF 53 – Health Effects
Cadmium (pH 6.5) 0.0002 0.03 ± 10% 0.005
Cadmium (pH 8.5) 0.00022 0.03 ± 10% 0.005
Cysts 99.99% > 50,000/L	99.95%
Lead (pH 6.5)	0.00012 0.15 ± 10% 0.010
Lead (pH 8.5)	0.0002 0.15 ± 10% 0.010
Mercury (pH 6.5)	0.0001 0.006 ± 10% 0.002
Mercury (pH 8.5)	0.0001 0.006 ± 10% 0.002

NSF 401 - Emerging Compounds/Incidental Contaminants

Substance Aqua	Fusion % Reduction	Influent Concentration (ng/L) % Reduction	Reduction Requirement / Maximum Filtered Concentration (ng/L)
Bisphenol A 95% 2000	± 20% 300
DEET 99% 1400 ± 20%	200
Estrone 96% 140 ± 20%	20
Ibuprofen 95% 400 ± 20%	60
Metolachlor 100% 1400	± 20% 200
Naproxen 96% 140 ± 20%	20
Nonylphenol 92% 1400	± 20% 200
TCEP 100% 5000 ± 20%	700
TCPP 100% 5000 ± 20%	700

VOC (organic chemicals by surrogate testing using chloroform)

Substance	AquaFusion % Reduction	Influent Concentration (mg/L) M	Maximum Allowable Filtered Concentration (mg/L)	% Reduction Requirement
Alachlor	>98%	0.050	0.001	>98%
Atrazine	>97%	0.100	0.003	>97%
Benzene	>99%	0.081	0.001	>99%
Carbofuran	>99%	0.190	0.001	>99%
Carbon Tetrachloride	98%	0.078	0.0018	98%
Chlorobenzene	>99%	0.077	0.001	>99%

VOC (organic chemicals by surrogate testing using chloroform-cont.)

Substance	AquaFusion % Reduction	Influent Concentration (mg/L)	Maximum Allowable Filtered Concentration (mg/L)	% Reduction Requirement
Chloropicrin 99% 0.015 0.0002 99%
2,4-D 98% 0.110 0.0017 98%
Dibromochloropropane (DBCP) >	99% 0.052 0.00002	>99%
o-Dichlorobenzene >99% 0.080 0	001 >99%
p-Dichlorobenzene >98% 0.040 0	001 >98%
1,2-Dichloroethane 95% 0.088 0.0048	95%
1,1-Dichloroethylene >99% 0.083	0.001 >99%
cis-1,2-Dichloroethylene >99% 0.170	0.0005 >99%
trans-1,2-Dichloroethylene >99%	0.086 0.001 >99%
1,2-Dichloropropane	>99%	0.080	0.001	>99%
cis-1,3-Dichloropropylene	>99%	0.079	0.001	>99%
Dinoseb	>99% 0.170 0.0002	99%
Endrin	>99% 0.053 0.00059	99%
Ethylbenzene	>99% 0.088 0.001 >99%
Ethylene Dibromide (EDB)	>99% 0.044 0.00002	>99%
Haloacetonitriles (HAN):
Bromochloroacetonitrile	98% 0.022 0.0005	98%
Dibromoacetonitrile	98% 0.024 0.0006	98%
Dichloroacetonitrile 98% 0.0096		0.0002	98%
Trichloroacetonitrile	98% 0.015 0.0003	98%
Haloketones (HK):
1,1-Dichloro-2-propanone	96% 0.0072	0.0001	96%
1,1,1-Trichloro-2-propanone	96%	0.0082	0.0003	96%
Heptachlor (H-34,Heptox) >99% 0.0250		0.00001 >99%

VOC (organic chemicals by surrogate testing using chloroform-cont.)

Substance	AquaFusion % Reduction	Influent Concentration (mg/L)	Maximum Allowable Filtered Concentration (mg/L)	% Reduction Requirement
Heptachlor epoxide 98% 0.0107 0.0002 98%
Hexachlorobutadiene > 98% 0.044 0.001 > 98%
Hexachlorocyclopentadiene > 99% 0.060 0.000002 > 99%
Lindane > 99% 0.055 0.00001 > 99%
Methoxychlor > 99% 0.050 0.0001 > 99%
Pentachlorophenol	> 99%	0.096	0.001	> 99%
Simazine	> 97% 0.120 0.004 > 97%
Styrene	> 99% 0.150 0.0005 > 99%
1,1,2,2-Tetrachloroethane	> 99%	0.081	0.001	> 99%
Tetrachloroethylene	99% 0.081 0.001 99%
Toluene > 99% 0.078 0.001 > 99%
2,4,5-TP (silvex)	99% 0.270 0.001 6 99%
Tribromoacetic acid	> 98%	0.042	0.001	> 98%
1,2,4-Trichlorobenzene	> 99%	0.160	0.0005	> 99%
1,1,1-Trichloroethane	95%	0.084	0.0046	95%
1,1,2-Trichloroethane	> 99%	0.150	0.0005	> 99%
Trichloroethylene	> 99%	0.180	0.001	> 99%
Trihalomethanes:
Chloroform (surrogate chemical)	95% 0.300 0.015 95%
Bromoform
Bromodichloromethane
Chlorodibromomethane
Xylenes (total)	> 99% 0.070 0.001 > 99%

Parts and Features

To order parts:

hamiltonbeach.com/parts

hamiltonbeach.ca/parts

1 Removable Needle Holder with Black Seal

2 Lid Button

3 Removable Water Reservoir with Lid

4 Removable Water Filter

5 Water Filter Well

6 Indicator Light

7 Removable Cup Mat

8 Base

9 Filtered Water Button

10 Flavor + Filtered 12 oz Button

11 Funnel Holder Opening

12 Removable Funnel

13 Removable Flavor Capsule Holder

Before first use: Wash Funnel, Flavor Capsule Holder, Needle Holder, Water Reservoir with Lid, and Cup Mat in hot, soapy water. Rinse and dry.

Exploded view diagram of a kitchen mixer with numbered parts for identification

How to Install and Flush Water Filter

Technical illustration of a mechanical device with two components and directional arrows indicating motion (no text or symbols)

1. Unplug AquaFusion from outlet.
2. Lift Water Reservoir straight up to remove.
3. In Water Filter Well, align Water Filter arrow with arrow outside Water Filter Well. Turn clockwise to lock in place.

Two identical hand-drawn diagrams of a coffee maker with cups, showing mechanical components and arrows indicating parts (no text or symbols present)

Diagram of a water pump system with two buckets and a handle, no text or symbols present

1. Remove Lid on Water Reservoir. Add only cold water to MAX Fill Line. Press Lid onto Water Reservoir.

2. Insert Funnel into Funnel Holder Opening, aligning Funnel Tab with opening cutout. Place Removable Flavor Capsule Holder in Funnel. NOTE: Ensure Needle Holder is locked into place.

CAUTION Cut Hazard. Removable needle holder has a sharp needle. Piercing needle on underside of lid is also sharp. Use caution when handling.

Technical line drawing of a mechanical device with a downward arrow indicating a component (no text or symbols present)

1. Holding Water Reservoir with opening for Water Filter in front, lower Water Reservoir into place to secure.

Line drawing of a cable plugged into an electrical outlet (no text or symbols)

1. Plug into outlet.

Line drawing of kitchen utensils including a blender and a blender with cups, arranged on a table (no text or symbols)

1. Place a large container on Cup Mat. Press and hold Filtered Water Button for three minutes to flush new Filter. Water dispensing will automatically stop after three minutes. Wait one minute; then press and hold Filtered Water Button again to drain all water from Water Reservoir. Discard filtered water and repeat process by filling Water Reservoir a second time. NOTES:

- If you start and stop the draining process, a three-minute automatic shutoff still occurs. - Flushing filter is only needed before Water Filter's first use.

How to Dispense Filtered Water

Line drawing of a wall-mounted electrical outlet with a cable, showing an outlet with three outlets (no text or symbols present)

1. Plug into outlet.
   NOTE: Ensure Removable Funnel is installed and Needle Holder is locked into place.

Line drawing of a coffee maker with a cup and handle (no text or symbols)

1. Place a glass on Cup Mat.

Line drawing of a hand using a brand blender to lift a glass of milk (no text or symbols)

1. Press and hold Filtered Water Button until desired amount of water has been dispensed.

How to Dispense Flavored Water

NOTES:

• Always insert Funnel before Flavor Capsule Holder.
- Do not lift Lid while water is dispensing. Lifting Lid causes cycle to stop. Dispenser will dispense an additional 12 ounces if restarted.
- Use only cold water in Water Reservoir. Do not use hot water.
- Do not dispense water without Removable Needle Holder locked in place.

Diagram showing electrical connection with power outlet, switch, and battery, plus upward arrow indicating action

1. Plug into outlet.
2. Press Lid Button to open Lid. NOTE: Funnel and Flavor Capsule Holder need to be in place before dispensing. See step 7 in "How to Install and Flush Water Filter."

⚠️ CAUTION Cut Hazard. Removable needle holder has a sharp needle. Piercing needle on underside of lid is also sharp. Use caution when handling.

Line drawing of a blender with a cup and two cups, showing a side view of the blender's interior (no text or symbols)

1. Place a flavor capsule into Capsule Holder. Do not remove foil.
2. Close Lid and snap in place to pierce flavor capsule.

Line drawing of hands using a coffee maker machine on a counter (no text or symbols)

1. Place a minimum 14-ounce glass on Cup Mat.
2. Press Flavor + Filtered Button to dispense 12 ounces of flavored water. NOTE: To stop dispensing, press Flavor + Filtered Button and press again within 5 minutes to restart.

Indicator Light

Continuous orange during operation: Operation is normal and filter monitoring system is working.

Flashes red 3 times and stops: Lid is not latched or Removable Funnel is not in place. Check Removable Funnel and make sure it is installed correctly. Close Lid and make sure it latches.

Flashes red, then yellow continuously: Water Reservoir is empty. Fill Water Reservoir with cold water to MAX Fill Line.

Filter is not in place. Remove Water Reservoir and secure Water Filter in Water Filter Well.

Continuous yellow during operation: Filter is close to end of life.

Continuous red during operation: Filter is at end of life and needs to be replaced.

Troubleshooting

Water remaining below Water Reservoir.

- This is normal if Water Reservoir has been removed and water is remaining.

Water on countertop.

• Water Reservoir is not placed properly onto Base. Remove Water Reservoir and carefully slide down into place.

Unit does not turn on when Flavor + Filtered Button or Filtered Water Button has been pressed.

- Make sure Removable Funnel is in place and Lid is latched.

Unit is running and not dispensing or has reduced water flow and Indicator Light is not red.

- Unplug. Check Water Filter for correct placement. Check for clogged needle in Removable Needle Holder and Removable Flavor Capsule Holder. Follow cleaning instructions in "Care and Cleaning" for "How to Fix a Clogged Needle."

- If needles in Removable Needle Holder and Removable Flavor Capsule Holder have been cleaned, replace Water Filter. Follow instructions for "How to Replace Water Filter."

Cup is overflowing.

- Use a cup with a capacity of at least 14 ounces.

- Lid opened and restarted without removing water from previous cycle. Do not lift Lid while water is dispensing. Lifting Lid causes cycle to stop. Dispenser will dispense 12 ounces if restarted.

AquaFusion turns off after an extended operation.

- This product is designed to turn off after 3 minutes of operation for Water Pump protection. Wait 1 minute before restarting.

Care and Cleaning

A WARNING Electrical Shock Hazard. Disconnect power before cleaning. Do not immerse cord, plug, or base in water or other liquid.

⚠️ CAUTION Cut Hazard. Removable needle holder has a sharp needle. Piercing needle on underside of lid is also sharp. Use caution

when handling.

1. Removable Funnel, Cup Mat, Flavor Capsule Holder, and Removable Needle Holder are dishwasher safe in top rack only.
2. Wash Water Reservoir and Reservoir Lid in hot, soapy water. Rinse and dry.
3. Wipe outside with a damp cloth and dry.

How to Fix a Clogged Needle

1. Unplug.
2. Remove Removable Needle Holder in Lid by turning the arrow counterclockwise from locked icon (☐) to unlocked icon (☐). Remove flavor capsule.
3. Bend a small paper clip. Insert tip of paper clip through hole of Piercing Needle in both Removable Flavor Capsule Holder and Removable Needle Holder and up into shaft of Piercing Needle to ensure sediment has been removed.
4. To replace gray Removable Needle Holder, insert tab between lock icon (☐) and unlocked icon (☐). Turn clockwise to lock.

Illustration of a hand holding a camera lens (no text or symbols visible)

How to Replace Water Filter

1. Lift Removable Water Reservoir straight up to remove.
2. Turn Filter counterclockwise to unlock and remove Filter.
3. Place new Filter in Water Filter Well and align Water Filter arrow with arrow outside Water Filter Well. Turn clockwise to lock in place.
4. Remove Lid on Water Reservoir. Add only cold water to MAX Fill Line. Press Lid onto Water Reservoir.
5. Holding Water Reservoir with opening for Water Filter in front, lower Water Reservoir into place. Add Lid and press down to secure.
6. Press and hold both Flavor + Filtered and Filtered Water buttons for at least 3 seconds. Indicator Light will flash when reset is complete and then will turn off.
7. After installing Water Filter, place a large container on Cup Mat. Press and hold Filtered Water Button to drain all water from Water Reservoir to flush new Filter. Discard filtered water and repeat process by filling Water Reservoir a second time.

Hamilton Beach Limited Warranty

This warranty applies to products purchased and used in the U.S. and Canada. This is the only express warranty for this product and is in lieu of any other warranty or condition.

This product is warranted to be free from defects in material and workmanship for a period of five (5) years from the date of original purchase in Canada and one (1) year from the date of original purchase in the U.S. During this period, your exclusive remedy is replacement of this product or any component found to be defective, at our option; however, you are responsible for all costs associated with our returning a product or component under this warranty to you. If the product or component is unavailable, we will replace with a similar one of equal or greater value.

This warranty does not cover glass, filters, wear from normal use, use not in conformity with the printed directions, or damage to the product resulting from accident, alteration, abuse, or misuse. This warranty extends only to the original consumer purchaser or gift recipient. Keep the original sales receipt, as proof of purchase is required to make a warranty claim. This warranty is void if the product is used for other than single-family household use or subjected to any voltage and waveform other than as specified on the rating label (e.g., 120 V \~ 60 Hz).

We exclude all claims for special, incidental, and consequential damages caused by breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty. This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or special, incidental, or consequential damages, so the foregoing limitations may not apply to you.

To make a warranty claim, do not return this appliance to the store. Please write Hamilton Beach Brands, Inc., Customer Service Department, 4421 Waterfront Dr., Glen Allen, VA 23060, or visit hamiltonbeach.com/customer-service in the U.S. or hamiltonbeach.ca/customer-service in Canada. For faster service, locate the model, type, and series numbers on your appliance.

PRÉCAUTIONS IMPORTANTES

Exploded view diagram of a kitchen mixer with numbered parts for identification

Technical illustration of a mechanical device with two components and directional arrows indicating assembly or movement (no text or symbols)

Diagram of a water pump system with two tanks and a side arm, showing liquid levels (no text or labels)

Technical line drawing of a mechanical device with a downward arrow indicating a component (no text or symbols present)

Line drawing of a cable inserted into an electrical outlet with three outlets (no text or symbols)

Two identical kitchen grilles with side monitors and a side sink, shown in side-by-side assembly (no text or symbols)

Line drawing of kitchen utensils and a hand holding a blender (no text or symbols)

Line drawing of a cable plugged into an electrical outlet with two outlets (no text or symbols)

Line drawing of a coffee maker with a cup and handle (no text or symbols)

Line drawing of a hand using a digital blender to press a glass of milk (no text or symbols present)

Diagram showing electrical connection with power outlet, switch, and battery, plus directional arrows indicating charging or discharging.

Line drawing of a blender with two cups, showing mechanical components and a side view of liquid (no text or symbols)

Line drawing of hands using a water dispenser on a kitchen sink (no text or symbols)

Illustration of a hand holding a camera lens assembly (no text or symbols visible)

Exploded view diagram of a kitchen mixer with numbered parts for identification

Technical illustration of a mechanical device with two components and directional arrows indicating assembly or movement (no text or symbols)

Simple line drawing of a kitchen sink with a water dispenser and a glass, no text or symbols present.

Technical line drawing of a mechanical device with a downward arrow indicating a component (no text or symbols present)

Line drawing of a cable inserted into an electrical outlet with two outlets (no text or symbols)

Two identical hand-drawn diagrams of a coffee maker with cups and cups, showing mechanical components (no text or symbols)

Line drawing of kitchen equipment including a blender and a blender with liquid, no text or symbols present

Line drawing of a cable plugged into an electrical outlet with two outlets (no text or symbols)

Line drawing of a hand holding a cup and pouring liquid into a digital coffee maker (no text or symbols)

Line drawing of a hand using a blender to press a glass of liquid (no text or symbols)

Illustration of a hand inserting a power outlet into a device (no text or symbols present)

Line drawing of a kitchen mixer with two cups and a side view showing liquid (no text or symbols)

Line drawing of hands using a water dispenser on a counter (no text or symbols)

Line drawing of a hand holding a camera lens (no text or symbols)