Sensor S15 - Vacuum Cleaner Kärcher - Free user manual and instructions

USER MANUAL Sensor S15 Kärcher

• How to Use This Manual

• Parts List The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual. The model and serial number of your machine is located on the bottom-back of the machine. The SAFETY section contains important information regarding hazardous or unsafe practices of the machine. Levels of hazards are identified that could result in product damage, personal injury, or severe injury resulting in death. The OPERATIONS section is to familiarize the operator with the operation and function of the machine. The MAINTENANCE section contains preventive maintenance to keep the machine and its compo- nents in good working condition. They are listed in this general order:

• Technical Details The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:

• ITEM – column refers to the reference num- ber on the parts illustration.

• PART NO. – column lists the part number for the part.

• NOTES – column for information not noted by the other columns. NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower right corner of the front cover. Model: Date of Purchase: Serial Number: Dealer: Address: Phone Number: Sales Representative: 8.643-554.0 Manual - Karcher Sensor S155 Safety

IMPORTANT SAFETY INSTRUCTIONS

When using this machine, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.

2. Connect to a properly grounded outlet only. See Grounding Instructions.3. Do not use outdoors or on wet surfaces.

4. Do not use near small children. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

5. Use only as described in this manual. Use only manufacturer's recommended attachments.

6. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center. 7. Do not pull or carry by the cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.8. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.9. Do not handle plug or appliance with wet hands. 10. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow. 11. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts. Do not place fingers or other body parts under vacuum unless unplugged.

12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

13. Do not use without dust bag and/or filters in place. Do not wash filters.14. Turn off all controls before unplugging.15. Use extra care when cleaning on stairs. 16. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may have been present. 17. Do not operate this machine near flammable fluids, dust or vapors.18. Maintenance and repairs must be done by qualified personnel.19. Use only identical replacement parts. See instructions for Servicing of Appliances.20. Do not use machine as a step.

21. If used on plush carpet or carpet with thick padding, do not leave machine in one place with machine turned on.

22. Do not use the handle in the dust bag housing to carry the machine.

23. Always turn off this appliance before connecting or disconnecting motorized nozzle.

24. Brush may unexpectedly restart. To reduce the risk of injury from moving parts. – Unplug before servicing.

25. The vacuum has a manual reset thermal protector. The protector is reset by switching off the vacuum. The thermal protector needs some time to cool down after switching off! Check the vacuum for air blockages or mechanical failures before switching on. 26. Store the vacuum in a dry place at room temperature. When the vacuum is not in use, you should wrap the cord on the cable hooks.

27. Any other servicing should be performed by an authorized service representative.

28. Make sure your extension cord is in good condition and is the correct size for your appliance. The table on the Grounding Instructions page shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized extension cord will cause a drop in line voltage resulting in loss of power and overheating. 29. Use only three-wire outdoor extension cords that have three-prong grounding plugs and grounding receptacles that accept the appli- ance's plug. 30. To reduce the risk of personal injury due to a loose electrical connection between the appliance's plug and extension cord, firmly and fully attach the appliance plug to the extension cord. Periodically check the connection while operating to ensure it is fully attached. Do not use an extension cord that provides a loose connection. A loose connection may result in overheating, fire, and increases the risk of a burning. 31. To reduce the risk of disconnection of the appliance cord from the extension cord during operating, make a knot as shown under Grounding Instructions.

32. Maintain Appliance With Care - Inspect extension cords periodically and replace if damaged.

READ AND SAVE THESE INSTRUCTIONS

8.643-554.0 Manual - Karcher Sensor S156 Safety Grounding Instructions This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordi- nances. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug illus- trated in sketch A. A temporary adapter looks like adapter illustrated in sketches B and C, may be used it connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a qualified electrician. The green colored rigid ear, lug or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw. NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code. Electrical In the USA this machine operates on a standard 15 amp 115 volt A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors Extension Cords If an extension cord is used, the wire size must be according to the table, and must be limited to 50 feet (15.5m) in length. USING AN ADAPTORGROUNDING CONNECTION Note: Adaptors are not allowed in Canada.OutletTab for GroundingOutlet BoxFIGURE CGroundedFIGURE AAdaptorScrewFIGURE BAdaptorMetal ScrewGroundedGrounding Pin Extension cords ratings and measures Ampere rating Volts Total length of cord 7.62m (25ft) 15,24m (60ft) 30,48m (100ft) More than A Not More than A mm² (AWG) 10 12 120 V 0.83 (18) 1.3 (16) 2.1 (14) Cord set Appliance cord (A) Tie cord as shown (B) Connect plug and receptacle Figure 1: Method of securing the appliance cord to the extension cord set 8.643-554.0 Manual - Karcher Sensor S157 Safety IMPORTANT SAFEGUARDS Accidents due to misuse can only be prevented by those using the machine. To guard against injury, basic safety precautions should be observed, including the following: Read and follow all safety instructions. Electric shock could occur if used outdoors or on wet surfaces. The vacuum cleaner is designed to be safe when used to perform cleaning functions. Should damage occur to electrical or mechanical parts, cleaner should be repaired by a competent service center before using in order to avoid further damage to machine or physical injury to user. A damaged power cord could cause electrical shock and/or fire. To minimize this possibility observe the following precautions: Do not run cleaner over power cord. Avoid closing doors on power cord pulling it around sharp edges, or placing sharp-edged objects upon it. Wind cord no tighter than is necessary to retain it on the cord hooks. When disconnecting power cord from electrical outlet, grasp the plug. Pulling it out by the cord itself can damage cord insulation and internal connections to plug. Your vacuum cleaner creates suction and contains a revolving brush. To avoid bodily injury from suction or moving parts, vacuum cleaner brush should not be placed against, or in close proximity of loose clothing, jewelry, hair or body surfaces while cleaner is connected to electrical outlet. Cleaner should not be used to vacuum clothing while it is being worn. Keep children away from machine when in operation or plugged in. If used on plus carpet or carpet with thick padding, turn off unit when handle is in upright position. When using accessory tools, keep floor bush off carpet by keeping handle in locked position and lowering handle with on hand to raise bush off floor. Operate accessories with other hand. Always plug your cleaner into a standard wall outlet. Use of extension cord or light socket with inadequate current-carry capacity could result in electric shock or fire hazard. Disconnect cleaner from electrical outlet before servicing, such as changing bags or belts. You could receive bodily injury from moving parts of machine should switch accidentally turned on. Disconnect cleaner from elec- trical outlet before detaching power head. Do not use your vacuum cleaner in areas where flammable and/or explosive vapor or dust is present to avoid possibility of fire or explosion. Some cleaning fluids can produce such vapors. Areas on which cleaning fluids have been used should be completely dry and thoroughly aired before being vacuumed. To avoid fire hazard, do not pick up matches, fireplace ashes, or smoking material with cleaner. Keep your work area well lighted to avoid picking up harmful materials (such as liquids, sharp objects, or burning substances) and avoid tripping accidents. Use care when operating the cleaner on irregular surfaces such as stairs, as falling cleaner could cause bodily injury and/or mechanical damage. Proper storage of machine in an out-of-way area immediately after use will also prevent accidents caused by tripping over cleaner. Store your vacuum indoors in a cool, dry area not exposed to the weather to avoid electrical shock and/or cleaner damage. Exercise strict supervision to prevent injury when using vacuum cleaner near children or when child is allowed to operate vacuum cleaner. Do not allow children to play with vacuum cleaner and never leave cleaner plugged in and unattended.

SAVE THESE INSTRUCTIONS

8.643-554.0 Manual - Karcher Sensor S158 Operation Components 1. Handle grip2. On/Off switch3. Handle assembly4. Retaining ring5. Cover release6. Dust bag housing7. Cover8. Housing release9. Brush/suction Head10. Cable11. Telescopic handle grip12. Hose13. Carrying handle14. Cable hook15. Attachment tube16. Crevice nozzle17. Upholstery nozzle18. Pile adjustment knob19. Foot pedal Preparation Place the brush/suction head (9) on a flat surfacewith the neck (20) and the support lever (21)upright. Hold the dust bag housing (6) verticallyand place over neck and support lever. Pushfirmly down so that the housing release (8)snaps closed.Lift the catch (22) then slot the handleassembly into the top of the dust bag housing(6) and push firmly down.When the handle (3) has been pushed down asfar as it will go press catch (22) down. If thehandle is not pushed fully down the machinewill not work.Insert attachment tube (15) into the channel atthe back of the machine. Locate the handlegrip (11) on the holder (23).Push the black end of the hose (12) into theconnecting tube (24) so that it clicks into place.Insert crevice nozzle (16) and upholstery nozzle (17)into the recesses in the back of the machine.The device is ready, you can start up by pressing the switch (2).

8.643-554.0 Manual - Karcher Sensor S159 Operation Filter level indicator The red warning light (A) indicates a blockage or a full bag, so check: a) Is the dust bag full? b) Is there a blockage in the hose or power head? If the red light is disregarded the machine will shut off and the light will flash. Brush controller The electronic brush controller continuously monitors the operation of the brush. If the red light (B) stays off, the operation of the brush is correct. If the red light (B) turns on in positions 1 - 4 of the Pile adjustment knob, adjust the brush by turning the Pile adjustment knob (18) to a lower position. If the red light (B) burns continuously in the position 1, the brush must be changed for a new one. If the machine turns off and the red light (B) flashes, the brush has become blocked and is not turning. Switch the machine off, unplug it from the mains and clear the blockage. If there is no blockage, and machine turns off with brush light flashing, raise brush to a higher position. When the machine is switched on in the upright position the brush automatically rises from the carpet. To release the machine from the upright position, press down the foot pedal (19). The brush will auto- matically lower. The handle can be lowered to an intermediate stop position in order to lift up the brush head. To lower the handle to a horizontal position, the foot pedal must be pressed a second time. The stop position can be closed off by a slider on the swivel neck (25) so that the handle will go from vertical to horizontal in one movement. To vacuum in corners etc., take hold of the telescopic handle grip (11), lift it away from the machine and stretch out the hose (12). After use, insert the telescopic attachment tube into the back of the machine. Raise the handle of the machine and the hose will automatically retract. To use the hose without the tube as shown in the right hand picture, the hose will pull out of the tube while the tube is fitted to the machine. Alternatively, press the release catch (27) on picture 2. You can now use one of the accessories (16) (17). Never run over the cable with the brush/suction head. Always carry the machine over steps and sills. Bag fullor clogCheck brush

8.643-554.0 Manual - Karcher Sensor S1510 Maintenance CAUTION - Always unplug machine at mains outlet before dismantling any part of machine. If red light (d) shows, change paper filter bag. To do this first pull cover release (5) picture 1 forward and lift the cover from the dust bag housing. Slide the dust bag sealing plate (28) from the holder (29). Slide the sealing plate (28) of a new bag into the holder and push firmly in. Insert cover into dust bag housing, push it forward then lock it in place by pushing down the cover release (5). The micro hygiene filter (30) needs to be changed when it becomes clogged with dust or after approxi- mately 20 paper bags have been used. To change the hygiene filter first remove the cover then slide the filter out at the bottom. To replace, lift the lever (31) and slide the new filter in. Fitting a New Exhaust Filter After 20 paper bags have been used also change the exhaust filter (32). To remove the exhaust filter push the catch (33) backward and remove the filter cover (34) and filter. Insert the new filter and replace the filter cover. Brush Roller To change the brush roller (35) push the button(36), remove the slide plate (37), turn the brush clockwise a quarter of a turn and pull the brush roller out. Slide the new brush roller into the brush housing and turn it until it locates into position. Push the button (36) and press the side plate (37) back into place.

8.643-554.0 Manual - Karcher Sensor S1511 Maintenance Removing Blockages Underneath the machine is an inspection door to check for blockages (38). Blockages in the neck (20 - picture 2) can be checked by first lifting off the dust bag housing by pressing the catch (8). Then release the foot pedal, lower the neck and check into the tube next to the pedal. Blockages in the hose can cleared by taking the hose off the machine and replacing it the wrong way round in the connecting tube (24) holding it upright with one hand blocking the top and switching on the machine. (If necessary quickly lift your hand on and off the end of the hose). The guarantee is invalidated if takeout parts not approved by manufacturer.eg. bags, filters, brush roller,etc. are fitted.

8.643-554.0 Manual - Karcher Sensor S1512 Maintenance Electric shock could occur if used outdoors or on wet surfaces!

3. 8.628-474.0 Dusting Brush

Power Head - S15 - continued ITEM PART NO. REF NO. DESCRIPTION NOTES