CBCB6750 - Range hood CIARRA - Free user manual and instructions

USER MANUAL CBCB6750 CIARRA

Model Number: CBCB6750 CBCB6750C www.ciarraappliances.comEN Dear customer: Thank you so much for your purchase, please read this instruction manual carefully before installation & use. If you have any question, please contact us at: E-mail: [e-mail]

D’INSTALLATION Page 49-72 ENGLISH DEUTSCH FRANÇAIS 1EN CONTENTS Safety------------------------------------------- 3-4 Specifications--------------------------------------5 Before Using the Cooker Hood ---------------------6 Prepare for Installation ----------------------------7 Installation--------------------------------------8-17 Install the Hood-------------------------------------------8-16 Carbon Filter Installation ------------------------------------17 Operation-------------------------------------- 18-19 Cleaning and Maintenance --------------------20-22 Grease Filter------------------------------------------------20 Carbon Filter------------------------------------------------20 Stainless Steel Cleaning------------------------------------20 Painted Finish Cleaning-------------------------------------20 LED Replacement----------------------------------------21-22 Troubleshooting-----------------------------------23 Environmental Protection-------------------------24 2EN Safety ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. Before servicing or cleaning unit, unplug or disconnect the cooker hood from the power supply. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities. Ducted fans must always be vented to the outdoors. Ensure the requirements of the local authorities are adhered to concerning the discharge of exhaust air. This unit must be grounded. When applicable local regulations comprise more restrictive installation and/or certification requirements, the aforementioned requirements prevail on those of this document and the installer agrees to conform to these at his own expense. Clean cooker hood frequently. Grease should not be allowed to accumulate on fans, filters or in exhaust ducts.

Warning: Failure to install the screws or fixing device in

accordance with these instructions may result in electrical hazards. 3EN Safety

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels —

This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

a) You own a Class ABC extinguisher and you know how to operate it. b) The fire is small and contained in the area where it started. c) The fire department has been called. d) You can fight the fire with your back to an exit. ! CAUTION For indoor use only. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. To avoid motor bearing damage and noisy and/or unbalanced fan blade, keep drywall spray, construction dust, etc. off cooker hood. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced. Always follows the cooking equipment manufacturer’s requirements regarding the ventilation needs. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside — Do not exhaust air into spaces within walls or ceiling or into attics, crawl space or garage. When installing, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. Please read specification label on product for further information and requirements. 4EN Specifications Voltage 220V-240V~ 50Hz Power of Motor 1 x 40W Power of lamps 1 x 2W Appliance Dimension 595*335*695~1075mm (W x D x H) Note: The manufacturer reserves the right to change any technological improvement or modification without prior notice.

Before Using the Cooker Hood CAUTION: Before proceeding to the installation, check if items are missing or damaged, contact the manufacturer. Observe all governing codes and ordinances. Have a qualified technician install the cooker hood. It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The manufacturer declines all responsibility for improper installation and does not accept responsibility for appliance warranty in the event of damage caused by incorrect installation. COMPONENTS: YOU WILL BE NEEDING THESE TOOLS FOR INSTALLATION 1.Protective Gloves 2.Spirit Level Ruler 3.Measuring Tape 4.Double Sided Tape or Tape 5.Cross-Head Screwdriver Set 6.Electric drill and 8mm drill

(CBCF002X2) 6EN Prepare for Installation Prepare for Installation: a) Ventilation Mode Recirculation Mode: Recirculating with carbon filter (required), the smells and odors can be filtered and vented through the top vented hole and the exhaust pipe is not required. Extraction Mode: You can install the 1.5m long and 150mm diameter aluminum exhaust pipe for extracting, which is included in the installation kit. b) When possible, use at least 60cm straight runs before any turns. Larger duct work may be required for best performance with longer duct runs. c) Before installation, don't connect the power. 7EN Installation Install the Hood（Extraction）:

1) Remove all protective poly film from the hood and/or parts.

2) Recommend installation height: 65~75cm above the cooktop for

best extraction. Required height over gas hob: 750mm; Required height over electric hob: 650mm. 650mm 750mm 8EN Installation

3) First use a pencil to mark the installation position on the wall, then

use a Measuring Tape to measure the height from the stove surface to the hood (the center point of aluminum grease filter) and use a Spirit Level Ruler to maintain the level, then use a pencil to draw a horizontal line along the level.

4) Poke the 7 perforated positions on the 1:1 Installation Diagram, then

align with the center point of aluminum grease filter on the Installation Diagram with the horizontal line on the wall, then tape the Installation Diagram to the wall, and use a pencil to mark the perforated positions on the wall in the corresponding positions. Spirit Level Ruler 650mm 750mm COMPONENTS:

Part 7: 1 :1 Installation Diagram X 1

1:1 Installation Diagram Tape 9EN Installation

5) Determine the maximum chimney installation height according to

the actual scenario and mark the chimney installation locations along the center line of the Installation Diagram.

6) Remove the Installation Diagram, drill the holes that have been

marked on the wall with an Electric Drill (8mm drill), and hammer the Wall Plug into the wall. Wall Plug COMPONENTS:

Part 1: Wall Plug X 9

Chimney installation locations 10EN Installation

7) Use three 4*30mm Screws to fasten the Wall Bracket on the wall.

8) Remove the aluminum grease filter and hang the hood on the

corresponding hook of the Wall Bracket. 4*30mm Screws 4*30mm Screws COMPONENTS:

Part 2: 4 *30mm Screws X 3

Part 10: Wall Bracket X 1

9) Use a Spirit Level Ruler to measure whether the hood is in a

horizontal level, and use two 4*30mm Screws to lock into the safety hole position of the hood (not mandatory, according to user's wishes to choose whether to lock). NOTE: Make sure you remove the tape on the damper and check if the damper opens and closes freely, otherwise it make noises, and the cooker hood will be shaking.

Part 2: 4*30mm Screws X 2

Spirit Level Ruler 4*30mm Screws 12EN Installation

11) Install the Aluminum Exhaust Pipe into the air outlet and lock it with

a Cable Tie; the other end of the Aluminum Exhaust Pipe will be pulled upward to outdoor and lock it with a Cable Tie (Note: This step can be ignored if use as recirculation mode with carbon filter).

12) Use two 4*8mm Screws to fasten the Lower Chimney Bracket on the

Lower Chimney. Lower ChimneyUpper ChimneyLower Chimney BracketUpper Chimney BracketLower Chimney BracketLower Chimney4*8mmScrews COMPONENTS:

Part 8: Lower Chimney Bracket X 1

Part 12: Lower Chimney X 1

Part 4: Aluminum Exhaust Pipe X 1

Part 5: Cable Tie X 1

Aluminum Exhaust PipeCable Tie 13EN Installation

13) Insert the Lower Chimney into the hood and fix it to the

corresponding positioning hole with two 4*8mm Screws. (Note: That the power cord needs to go through the chimney and connect the power).

14) Use two 4*30mm Screws to lock the Lower Chimney Bracket into the

Part 2: 4*30mm Screws X 2

4*8mm Screws Power Plug 14EN Installation

15) Use two 4*30mm Screws to lock the Upper Chimney Bracket to the

corresponding positioning holes on the wall.

16) Put the Upper Chimney into the Lower Chimney, and then pulled

to the height of the Upper Chimney Bracket. COMPONENTS:

Part 13: Upper Chimney X 1

Upper Chimney COMPONENTS:

Part 9: Upper Chimney Bracket X 1

Part 2: 4*30mm Screws X 2

4*30mm Screws 15EN Installation

17) Use two 4*8mm Screws to assemble the Upper Chimney on the

Upper Chimney Bracket.

18) Turn the LED lights on/off, and test whether the functions are working

properly. COMPONENTS:

1. Carbon filter can be used to trap odors.

In order to install the carbon filter, the grease filter should be detached first. Press the lock and pull it down.

3. If the carbon filter needs to be replaced, please turn it in the anti-

clockwise direction. NOTE: Make sure the carbon filter is securely locked. When the carbon filter is installed, the suction of the cooker hood will be reduced. The carbon filter should be changed every 2-4 months depending on the conditions of use.

2. Place the carbon filter into the unit and turn it in the clockwise

direction to lock it in place. 17EN Operation Always turn your hood on before you begin cooking to establish an airflow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the hood. This will help to keep the entire kitchen clean and fresh. Mechanical Push button Operate the hood as follows: Off button It's used to turn off the fan. Low Speed button For air ventilation with barely no noise; or simmering with very little smoke and steam. Medium Speed button For your everyday cooking purpose. High Speed button High-Speed for stir-fry or cooking with lots of smoke and grease produced. Light button When lights are OFF, press this button once to turn ON the lights. Press this button again to turn OFF the lights. 18EN Operation Press once, turn on the LED light in level 1, Press for the second time, turn on the LED light in level 2, increase brightness; Press for the third time, turn off the LED light.

ys turn your hood on

ore you begin cooking to establish an airflow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the hood. This will help to keep the entire kitchen clean and fresh. Electronic button Operate the hood as follows: On/Off button It's used to turn on/off the fan.Press 2S to power on, press 1S to power off. Low Speed button For air ventilation with barely no noise; or simmering with very little smoke and steam. Medium Speed button For your everyday cooking purpose. High Speed button High-Speed for stir-fry or cooking with lots of smoke and grease produced. Light buttonEN Cleaning and Maintenance Proper maintenance of th

Cooker Hood will assure proper performance of t he unit. Before cleaning unit, unplug or disconnect the cooker hood from the power supply. GREASE FILTERS The grease filters should be cleaned frequently. Can be cleaned in dishwasher under high temperature without using any detergent. CARBON FILTER The carbon filter should be changed every 2-4 months depending on the conditions of use. Replace more often if your cooking style generates lots of greases, such as stir frying. These filters are not washable and cannot be reused. Refer to installation instructions included with a carbon filter.

STAINLESS STEEL CLEANING

Do: Regularly clean it with a cloth or rag soaked with warm water and mild soap or liquid dish detergent. You may also use a specialized household stainless steel cleaner. Don't: Use any steel or stainless-steel wool or any other scrapers to remove stubborn dirt. Use any harsh or abrasive cleansers. Let plaster dust or any other construction residues reach the hood. During construction/ renovation, cover the cooker hood to make sure no dust sticks to the stainless-steel surface. Avoid when choosing a detergent: Any cleaners that contain bleach will attack stainless steel. Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly. Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range. PAINTED FINISH CLEANING: Clean with warm water and mild detergent only. If discoloration occurs, use a finish polish such as automotive polish. (DO NOT use a rough abrasive cleaner or porcelain cleaner.) 20EN

Cleaning and Maintenance LED REPLACEMENT Rectangle LED lamp: CAUTION

Before cleaning or repairing and replacing accessories, please make sure to shut down the power before operation, so as to avoid electric shock, damage to human body and even endanger life safety!

1. Turn off the hood and unplug the power outlet. Detach the grease

filter in order for you to replace the LED lamp.

2. Push the LED lamp holder out from the cabinet by hand, or use

screwdriver to prize up the LED lamp around the edges, pull out slotted the LED lamp and the wire together. 21EN Cleaning and Maintenance

3. Open the power protection cover, pull out the plug and replace the

corresponding model of the LED lamp.

4. Turn the power on and test all blower and light functions to ensure

they are operating properly. Insert the new LED light gently into the light socket, please make sure you aim at the grooves on the lighting panel when installing. Push the LED light in until it is flushed with the light panel.

5. Put the grease filter back on, you are good to go.

Part 10: Support mural X 1