CECUF166NFW - Freezer CONTINENTAL EDISON - Free user manual and instructions

USER MANUAL CECUF166NFW CONTINENTAL EDISON

SAFETY ADVICE Before any use, please read the following instructions carefully and keep this manual. For your safety and for the correct use of the device, before installing and using the device for the first time, read this manual carefully, including the warnings and the useful advice it contains. In order to avoid damaging the device and / or injuring yourself unnecessarily, it is important that those who use this device are fully aware of its operation and its safety functions. Save these instructions for later use and remember to store them next to the appliance, so that they areEN-2 Important information about your personal safety and how to avoid damaging the device. General information and advice Risk of electric shock Do not use electrical devices, such as a hairdryer or a heater to defrost your freezer. Containers containing flammable gases or liquids may leak at low temperatures. Do not store containers with flammable materials, such as aerosol cans, fire extinguishers, fire cartridges etc in the freezer.EN-3 Do not store carbonated or sparkling drinks in the freezer. Ice cream can cause "frost / gel burns" if eaten directly from the freezer. Do not remove items from the freezer compartment if your hands are wet / wet, as this may cause skin damage or "freezing burns". Bottles and cans should not be placed in the freezer compartment as they may burst when the freezer. The storage times recommended by the manufacturer must be observed. Refer to the relevant instructions. Do not allow children to tamper with the controls or play with the freezer. The freezer is heavy. Care should be taken when moving it.EN-4 t is dangerous to change the specifications or attempt to modify this product in any way. Do not store flammable gases or liquids inside your freezer. If the power cable is damaged, it must be replaced by the manufacturer, its service agent or a qualified person in order to avoid danger. This device can be used by children from 8 years old and people with reduced physical, sensory or mental capacities or a lack of experience and knowledge if they have received supervision or instructions concerning the use of the device. device safely and understand the dangers involved. Children should notEN-5 play with the device. Cleaning and user maintenance must not be carried out by children without supervision. The device is intended for use in domestic and similar places such as:

• Staff kitchen areas in stores, offices and other work environments;

• Farm houses and by clients in hotels, motels and other residential type environments;

• Bed and breakfast type environments;

• Catering and similar non- commercial applications. Please keep the ventilation openings of the appliance and the built-in cabinet free.EN-6 Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. Do not damage the refrigerant circuit. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. Do not store explosive substances such as aerosol cans with a flammable propellant in the device.EN-7 This device is not intended for use by persons (including children) with reduced physical, sensory or mental abilities, or a lack of experience and knowledge, unless they have received supervision or instructions regarding the use of the device by a person responsible for their safety. Children should be supervised to ensure that they do not play with the device.

WARNING: Keep the ventilation

openings, in the device housing or in the integrated structure, free from any obstruction.EN-8

WARNING: Do not use mechanical

devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. WARNING: Do not damage the refrigeration circuit.

WARNING: Do not use electrical

appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

WARNING: Type I freezers may

not function properly (possibility of defrosting the contents or raising the temperature in frozen food) when LOCATED for a long period of time in a room where the temperature is lower than the minimum device temperature.CAUTION: It is necessary, for doors or covers fitted with locks and keys, to keep the keys out of the reach of children and not near the refrigerating appliance, in order to avoid children being locked up inside.

WARNING: The refrigerant used in

your appliance and the insulation materials require special disposal procedures.

WARNING: When positioning the

machine, make sure that the power cord is not pinched or damaged.

WARNING: Do not place multiple

portable power outlets or portable power supplies on the back of the device. Children aged 3 to 8 years are allowed to load and unload refrigeration appliances. EN-9To avoid contamination of food, please observe the following instructions:

• Prolonged opening of the door can lead to a significant increase in the temperature inside the appliance.

• Regularly clean surfaces that may come into contact with food and accessible drainage systems.

• Store raw meat and fish in suitable containers in the freezer so that they do not come into contact with or drip onto other foods.

• The compartments for two-star frozen food suitable for storing pre- frozen food and for storing or making ice or cream and for making ice cubes. EN-10EN-11

• The one, two and three star compartments are not suitable for freezing fresh food.

• If the refrigeration appliance is left empty for long periods, switch off, defrost, clean, dry and leave the door open to prevent the formation of mold inside the appliance.Electrical Connection WARNING This appliance must be properly grounded for your safety. The power cord for this appliance is equipped with a three-prong plug that fits into standard three-prong wall outlets to minimize the risk of electric shock. Do not cut or remove the third grounding prong from the supplied power cord. This refrigeration appliance requires a standard 220-240VAC 50Hz electrical outlet with three-prong grounding. This freezer is not intended for use with an inverter. The cord should be tied behind the device and should not be exposed or hung to avoid accidental injury. EN-12Do not unplug never use the freezer by pulling on the power cord. Enter always firmly hold the plug and pull it straight out of the socket. Do not use an extension cord with this appliance. If the power cord is too short, have an outlet installed near a appliance by a qualified electrician or technician. The use of an extension cord may adversely affect the performance of the device. Improper use of the grounded plug can result in a risk of electric shock. If the power cord is damaged, have it replaced by an authorized service center. EN-13Place the device against a wall whose free distance does not exceed 75 mm and exceeds 50 mm.

WARNING: When positioning

the machine, make sure that the power cord is not pinched or damaged.

WARNING: Do not place

portable multiple outlet bases or portable power supplies at the rear of the device. EN-14EN-15 Danger; risk of fire / flammable materials

1) Do not use mechanical

devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

2) Do not obstruct any

ventilation grille on the device.

3) Do not store explosive

substances such as aerosol cans with a flammable propellant in this device.4) Do not damage the refrigeration circuit of the appliance.

5) Since the refrigeration

units work with isobutane (R600a), they cannot be placed in an area with sources of ignition (for example, unsealed electrical contacts or when the refrigerant could collect in the event of a leak). The type of refrigerant is indicated on the cabinet nameplate. EN-16EN-17

6) Do not use electrical

appliances in the compartments of the appliance, unless they are of the type recommended by the manufacturer. To avoid the risk of injury, keep this leaflet. The manufacturer cannot be held responsible for improper handling of the device. In the interest of constant improvement of our products, we reserve the right to modify the technical characteristics without notice. Suitable for food Information on the meaning of the conformity marking The marking indicates that the product meets the main requirements of the European Directives: 2014/35 / EU (Low Voltage), 2014/30 / EU (Electromagnetic Compatibility), 2011/65 / EU (Limitation of use of certain substances in equipment electronic)EN-18 SUMMARY Important safety warnings and advice

I. Description of the device

VI. Food preservation

VII. Cleaning and maintenance

This user guide is available in the following languages: - FR (original version) - EN (translated from the original) Any other translation would be a translation of the original version. This user guide, any changes or any new version, is available on our website.I. DESCRIPTION OF THE APPARATUS

Due to technological innovation, the product descriptions in this manual may not be entirely consistent with your freezer. EN-19

Adjustable feetEN-20

Model: MF-181W freezer category: 8, Congélateur amoire Energy efficiency class: A+ Energy consumption : 238 kWh per year, calculated on the basis of the result obtained for 24 hours under standardized test conditions. The actual energy consumption depends on the conditions of use and the location of the device. Useful freezer volume (l):

Defrost: Automatic Autonomy in the event of a power cut: 16,8 h Freezing power: 8 kg/24h Climate class: SN / N / ST This device is designed to be used at an ambient temperature between 10°C and 38°C. Acoustic emissions to air in dB (A) re 1 pW: 42 dB(A) Installation type: Freestanding The actual energy consumption depends on the conditions of installation and use of the device.EN-22

• Remove all packing material from around the device, as well as the protective parts from inside the device compartments.

• The cardboard packaging and the sheets of paper are recyclable. They must be disposed of in the collection bins provided for this purpose.

• Materials bearing the symbol are recyclable: >PE<= polyéthylène ; >PS<= polystyrène ; >PP<= polypropylène This means that they can be recycled by depositing them in appropriate collection containers.

The other packaging elements (adhesive, fasteners, etc.) must be disposed of with household waste. To find out more: www.quefairedemesdechets.fr

2. CLEANING THE APPLIANCE

Clean all parts of the freezer with water and a mild detergent solution. Rinse it thoroughly and dry it with a soft cloth. Note: The electrical parts of the device can only be cleaned with a dry cloth.

ABefore using the freezer, remove all packing materials and protections from the freezer. Adjust the adjustable feet and clean the inside and outside of the freezer with water and a mild detergent solution. Rinse thoroughly and dry with a soft cloth. Do not start the freezer immediately after installation. You must wait 2-6 hours before switching on the device when switching it on for the first time. To avoid accident, do not cover the power cord.EN-23 Before plugging in the appliance, make sure that the voltage of the electrical outlet in your home corresponds to that indicated on the rating plate. When the freezer is first installed, allow it to stabilize at normal operating temperature for 2-3 hours before filling it with fresh or frozen food. If the device is interrupted, wait 5 minutes before restarting it.EN-24

IMPORTANT: The installation of this device requires the intervention of 2 people. Location When selecting a position for your freezer, you need to make sure that the floor is flat and firm, and that the room is well ventilated with an average room temperature between 10℃ and 43℃. Avoid placing your freezer near a heat source, such as a stove, boiler, or radiator. So avoid direct sunlight on over-buildings or sunbeds. Make sure that the freezer is not placed near humidity (dryer for example) otherwise condensation will occur on the freezer cabinet. Never place the freezer in a wall or built into built-in cabinets or furniture. When your freezer is on, the grill on the back can get hot and the sides hot. Therefore, it must be installed leaving at least 9 cm of free space behind and the sides 5 cm. Upgrade If the freezer is not level, the door gasket and magnetic alignment will be affected. Once the freezer is placed in its final location, adjust the adjustable feet at the front by turning them. Cleaning before first use Wipe the inside of the freezer with a dilute solution of baking soda. Then rinse with lukewarm water with a sponge or damp cloth. Wash the trays and shelves. In hot soapy water and dry completely.EN-25 Installation location

1. Ventilation conditions

The position you choose for the installation of the freezer must be well ventilated and have as little hot air as possible. Do not place the freezer near a heat source such as a stove, boiler and avoid direct sunlight, thus ensuring the cooling effect while saving energy consumption. Do not place the freezer in a humid place, to prevent the freezer from rusting and loss of electricity. The result of the total space of the room in which the freezer is installed divided by the amount of refrigerant charge of the freezer should not be less than 8 g / M 3. Note: the amount of refrigerant charged for the freezer can be found on the rating plate.

2. Heat dissipation space

When operating, the freezer releases heat to the environment. Therefore, at least 300mm of free space should be maintained on the top side, more than 100mm on both sides and more than 50mm on the back of the freezer Dimensions in mm:

Note: Figures 1 and 2 show only the product's demand for space.3. Upgrade Place the freezer on a solid, flat floor (floor) to keep it stable, otherwise it will cause vibration and noise. When the freezer is placed on floor coverings such as carpet, straw rugs, polyvinyl chloride, solid support plates should be applied under the freezer so as to prevent color change due to heat dissipation. Clear ventilation must be maintained around the device or in a built-in structure. Preparations for use

Once the freezer is properly installed and properly cleaned, do not turn it on immediately. Be sure to turn on the freezer after more than an hour of rest to ensure normal operation.

Attach the accessory parts to the interior of the freezer and wipe the interior with a soft cloth.

Insert the plug into the socket to start the compressor. After 1 hour, open the freezer door, if the temperature in the freezer compartment drops significantly, the refrigeration system is operating normally.

Once the freezer has been operating for a period of time, the internal temperature of the freezer will be automatically controlled according to the setting by the user. When the freezer is completely cool, put the food in, which usually takes 2 to 3 hours to be completely cooled. In summer, when the temperature is high, it takes more than 4 hours for the food to cool completely (try to open the freezer door as little as possible before the internal temperature cools). If the freezer is installed in a damp location, make sure that the ground wire and the leakage breaker are normal. If vibration noises are produced due to the freezer contacting the wall or if the wall becomes blackened by convection of air around the compressor, move the freezer away from the wall. Installing the freezer nearby may cause interference or noise in the mobile phones, landlines, radio receivers and television surrounding it. Try to keep the freezer as far as possible in this case. EN-26EN-27 Reverse the door

1. Make sure your freezer is unplugged.

2. Lift and remove the hinge cover, remove the three screws that

secure the upper hinge to the door, then remove the hinge.

3. Remove the freezer compartment door from the cabinet.

4. Remove the screws that secure the bottom hinge to the right

side of the cabinet, and then remove the hing.

5. Remove the washer and nut that secure the spindle axle to the right

hole in the lower hinge, then remove the axle.

6. Insert the spindle axis into the left hole of the lower hinge,

then secure the axis with the washer and nut.EN-28

7. Install the bottom hinge on the left side of the cabinet.

8. emove the screw that fixes the door stopper at the bottom right of

the freezer compartment door, then remove the door stopper and install it at the bottom left.

9. Install the freezer compartment door.

10. Move the door socket from the upper right side of the freezer door

to the upper left side of the door. And move the left hole cover to the right side.

11. Remove the screw that secures the hinge hole cover on the upper

left side of the cabinet, remove the cover and attach the cover to the upper right side of the cabinet.

12. Attach the upper hinge to the upper left side of the cabinet

with the three screws that you removed previously. Before tightening the upper hinge screws, make sure that the top of the door is flush with the cabinet and that the rubber seal provides a good seal.

13. Install the hinge cover on the hinge on the upper left side of

14. Remove the plugs from the left hole, unscrew the bolts and remove

the plug from the right hole.

15. Install the right hole plugs on the left side of the door, and install the

handle on the right side of the door.EN-30 1 Functions

1.1 Setting the temperature

The temperature can be adjusted by pressing the «SET». button. Each time you press the «SET», key, the current mode indicator goes out while the next mode indicator lights up, with said mode setting validated if no key operation within 5 seconds (otherwise the mode setting will be invalid). Once the setting is applied, the temperature will be immediately controlled according to the mode setting. The temperature setting cycle is as follows: “-16℃→-18℃→- 20℃→- 22℃→-24℃→ (fast freezing) →-16℃” 。

When the quick freeze function is activated, the temperature of the compartment can be cooled quickly, which is beneficial in preventing food nutrition from loss and preserving freshness. After a cumulative operating period of 26 hours, the quick freeze function will close automatically, with the temperature mode restored to that set before activating the quick freeze function.

When the freezer door remains open for more than 3 minutes, the buzzer starts to emit alarms, which can be suspended for 3 minutes by pressing any key, but they will not be stopped until said door be closed. When the freezer is connected to the power supply for the first time, all the icons on the display panel light up for 2 seconds and the system operates at -18 ° C by default.

In the event of a power failure, the freezer will maintain the operating state before the power failure when the power is restored.

In order to protect the compressor fridge fr om being damage d in the event of a short-time power failure (less than 5 minutes), the compressor will not start immediately after switching on.

1.6 Defrost the device

Defrosting can be done automatically or manually if the freezer does not defrost, the automatic defrosting program can be activated by pressing and holding the SET button for 15 seconds, with all the mode lights on, the refrigeration stopped and the heating of defrost started. During the defrosting process, you can hold down the SET button for 3 seconds to stop defrosting manually, or wait for the defrosting program to end automatically. In order to avoid frequent defrosting actions of the freezer do not access the defrosting function during the defrosting process; make sure not to reactivate the defrosting function within 10 minutes after its manual deactivation.

When the alarm indicator continues to flash (with the corresponding «-16, -20, -24 or fast freeze» light flashing simultaneously), it indicates a problem with the freezer Please contact customer service for a visit.EN-32

VI. CONSERVATION OF FOOD

Storage locations Shelf: when you take out the shelf, lift it upwards, then remove it; When installing the shelf, be sure to place it in position before installing it. Crisper box (drawer): You can pull the drawer to access the food. Do not put too much or too much weight in the freezer Keep enough space between foods; if it is too close, the cold air flow will be blocked, thus affecting the cooling effect. Do not store excessive or overweight food to prevent the tablet from being crushed. When storing food, keep a distance away from the inner wall; and do not place water-rich foods too close to the back wall of the freezer as they may freeze on the inside wall. Freezing mode Long-term food freezing: The freezer compartment, where the temperature is generally controlled below -18 ℃, is suitable for long- term food storage, but the shelf life indicated on food packaging must be observed. Freezer drawer: Used for storing frozen food; For large pieces of meat or fish, cut them into smaller pieces, pack them separately with the storage bags and distribute them evenly in the drawer. Fast freezing (1) Refer to the description of the quick freeze function in the «Fonction» section. (2) Compared to normal freezing, rapid freezing allows food to pass through the ice crystal formation area faster and without damaging the cell membrane, so that cell juice will not be lost during thawing, and the original freshness and nutrition of the foods maintained. (3) The quick freeze function is designed to preserve the nutrition of frozen food, the food being completely frozen as soon as possible. Fast freezing consumes more energy than normal freezing.EN-33 ★ Let hot food cool to room temperature before putting it in the freezer compartment. ★ Do not place a glass container containing liquid or the sealed canned liquid in the freezer compartment, to avoid bursting due to the expansion of the volume once the liquid is frozen. ★ Divide the food into appropriate small portions. ★ It is best to pack food before freezing. The packaging bag used must be dry, in case the packaging bags are frozen together. Food must be wrapped or covered with suitable materials that are firm, tasteless, air and water impermeable, non-toxic and pollution-free, to avoid contamination cross and odor transfer. Tips for buying frozen food

1. When purchasing frozen food, see the storage instructions on the

package. You can keep each food frozen for the period indicated in relation to the number of stars. This is usually the period indicated as «Better to use before ×», which is on the front of the package.

2. Check the temperature of the frozen food cabinet in the store where

you buy frozen food.

3. Make sure the frozen food packaging is in perfect condition.

4. Always buy frozen products last when shopping or visit the

5. Try to keep frozen food together while shopping and on the way

home, as this will help keep food cool.

6. Do not buy frozen products unless you can freeze them immediately.

Special cooler bags can be purchased at most supermarkets and hardware stores. These keep food frozen longer.

7. For some foods, defrosting before cooking is not necessary.

Vegetables and pasta can be added directly to boiling water or steamed. Frozen sauces and soups can be put in a saucepan and gently heated until thawed.

8. Use quality food and handle it as little as possible. When food is

frozen in small batches, it will take less time to freeze and thaw.

9. Estimate the amount of food to be frozen. When you freeze large

quantities of fresh produce, set the temperature control knob to low mode, with the freezer temperature lowered. Thus, food can be frozen quickly, with the freshness of the food well preserved.EN-34 II.Tips for Special Needs Moving the fridge / freezer

• Location Do not place your fridge / freezer near a heat source, such as a stove, boiler or radiator. Avoid direct sunlight in outdoor buildings.

• Upgrade Make sure to level your fridge / freezer using the front leveling feet. If it is not level, the sealing performance of the freezer / freezer door gasket will be affected, or even it may cause your freezer / freezer to malfunction. After placing the freezer / freezer in position, wait 4 hours before using it, to allow the refrigerant to settle.

• Installation Do not cover or block the ventilation slots on your device. When you are away for a long time

• If the appliance has not been used for several months, switch it off first and then disconnect the plug from the wall outlet.

• Clean and dry the interior thoroughly. To avoid the formation of odors and mold, leave the door ajar: block it or have it removed if necessary.

• Keep the cleaned appliance in a dry and ventilated place and away from heat sources, move the appliance smoothly and do not place heavy objects on it.

• The device must not be accessible to children. Tips for saving energy

• Install the device in a cool, dry room with adequate ventilation.

• Make sure it is not exposed to direct sunlight and never place it near a direct heat source (eg a radiator).

• Do not block the vents or grilles, for maximum energy efficiency.

• It is recommended to install the device with a clearance at the back and on the sides. This will help reduce energy consumption and lower your electricity bills.

• Allow hot foods to cool before placing them in the fridge.

• Place frozen food in the refrigerator to defrost.

• Do not leave the door of your appliance open for too long, when adding or removing food.

• For efficient use of energy, respect the original position of all internal accessories (baskets, drawers, shelves).VII. CLEANING AND MAINTENANCE Before cleaning, first unplug the power plug. Do not insert or unplug the plug with wet hands, as there is a risk of electric shock and injury. Do not spill water directly on the freezer to avoid rust, electrical leakage and accidents. Do not stretch your hands against the bottom of the freezer as you may be scratched by sharp metal corners. Interior and exterior cleaning Food residue in the freezer may cause a bad odor, so the freezer should be cleaned regularly. The fresh food compartment is usually cleaned once a month. Remove all shelves, vegetable drawer, bottle holder, lid and drawers, etc., and clean them with a soft towel or sponge dipped in warm water or neutral detergent. Frequently remove dust from the rear panel and side plates of the freezer After using a detergent, be sure to rinse it off with clean water, then wipe it off. Do not use a bristle brush, wire brush, detergent, powdered soap, alkaline detergent, benzene, gasoline, acid, hot water, and other corrosive or soluble items to clean cabinet surface, door gasket, plastic decorative pieces, etc., so as to avoid damage. Carefully wipe the door seal, clean the groove with a wooden rod wrapped in cotton string. After cleaning, first fix the four corners of the door seal, then incorporate it segment by segment in the door groove. Power supply interruption or refrigeration system failure

• Take care of frozen food in the event of prolonged non-operation of the refrigeration appliance (such as an interruption in the power supply or a breakdown of the refrigeration system).

• Try to open the freezer door as little as possible, this way food can be kept safe and fresh for hours, even in hot summer.

• If you receive the notice of power failure in advance:

1) Set the thermostat knob to high mode one hour in advance, so that

the food is completely frozen (do not store new food during this period!). Restore the temperature mode to the original setting when the power supply returns to normal in due course.

2) You can also make ice with a sealed container and put it in the top

of the freezer, to extend the shelf life of fresh food. Note: Once the freezer is used, it is best to use it continuously. Under normal circumstances, do not stop using it so as not to affect its lifespan. EN-35EN-36 Defrost This device is designed with an automatic defrost function, so no need to defrost it manually. Replace the lamp The freezer uses an LED lamp for lighting, which is characterized by low energy consumption and long service life. In the event of an anomaly, please contact the after-sales service for a visit. The lamps can only be replaced by the manufacturer, as well as part of the device. Safety and verification after maintenance Is the power cord broken or damaged ? Is the power plug firmly inserted into the outlet ? Is the power plug overheating abnormally ? Note: Electric shock and fire can occur if the power cord and plug are damaged. In the event of an anomaly, please disconnect the power plug and contact the seller. How to disassemble the shelf parts: Hold one end of the shelf and lift it up while pulling it outward. Flip cover: Keep the cover hinged in the vertical direction, align it with the opening of the rotating shaft on the right side and pull it outwards to remove it. Do not close the door with the hinged lid open, otherwise the freezer door may be damagedEN-37

VIII. FAULTS AND SOLUTIONS

Maintenance This device must be repaired by an authorized technician and only spare parts from the manufacturer must be used. Under no circumstances should you attempt to repair the device yourself. Repairs carried out by inexperienced persons may cause damage or serious damage. Problem resolution Before you call customer service, check if you can resolve the issues. Case Inspection Solutions

• Does not cool at all

Is the power plug disconnected?

Are the circuit breakers and fuses blown?

• Open the door and check if the lamp comes on.

Is the freezer stable?

Does the freezer come into contact with the wall?

• Adjusting the leveling feet of the freezer

• Move away from the wall.

Are you putting hot food or too much food?

Do you often open the door?

Are you attaching the food bag to the door seal?

Direct sunlight or near a furnace or stove?

Is it well ventilated?

Temperature setting too high?

• Put food in the refrigerator when hot food becomes cold.

• Check that the door is closed.

• Remove the refrigerator from the heat source.

• Increase the distance to maintain good ventilation.

Have you packed strong flavor foods?

• Throw away spoiled food.

• Cleaning the freezer

• Packaging of foods with strong flavors.

• Temperature adjustment not possible

• Exit the special operating mode, then set the temperature (for more details (see Functions section)EN-38

• Freezer temperature displayed on the panel, with the digits of flashing temperature

I cut the power before?

• Press any key to raise the alarm (see the Overheat alarm function), then check the food in the freezer and the freezer compartments. For any other problem occurring with your device: contact the After-Sales Service.EN-39

The logo on the product means that it is a device whose treatment as waste within the scope of Directive 2012/19/EU of 4 July 2012 on electrical and electronic waste (WEEE). This means that it must be supported by a selective collection system according to the European directive mentioned above in order to be either recycled or dismantled in order to reduce any impact on the environment. For more information, you can contact your local (town hall) or regional administration. Electronic products that have not been sorted are potentially dangerous for the environment due to the presence of dangerous substances. In no case should you throw this device on the public highway. When this device reaches the end of its useful life, you must deposit it in a selective collection center so that it is destroyed and / or recycled in an appropriate selective collection system which will take care of their respective destruction and / or recycling.X. WARRANTY The warranty does not cover product wear parts, no problems or damage resulting from:

Surface damage due to normal wear and tear;

Defects or damage due to contact of the product with liquid and due to corrosion caused by rust or the presence of insects;

Any incident, abuse, misuse, modification, unauthorized removal or repair;

Any improper maintenance operation not in accordance with product instructions or connection to improper voltage use;