INKI112CBK16 - Pest control NEDIS - Free user manual and instructions

USER MANUAL INKI112CBK16 NEDIS

Quick start guide Insect Killer INKI112CBK16 For more information see the extended manual online: ned.is/inki112cbk16 Intended use The Nedis INKI112CBK16 is an electronic insect killer. It utilizes a UV-A LED tube to attract light sensitive ying insects, such as ies, moths, and mosquitoes. These insects are electrocuted by the electrically charged inner metal grid. The product is intended for indoor, domestic use only. This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Any modication of the product may have consequences for safety, warranty and proper functioning. Specications Product Insect Killer Article number INKI112CBK16 Grid voltage 4000 V Input voltage 220 - 240 V ~ 50 / 60 Hz Lamp UV-A LED Power 11 W Lifespan ± 20000 hours Eective range 150 m

• Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep the packaging and this document for future reference.

• Only use the product as described in this document.

• The manufacturer is not liable for consequential damages or for damages to property or persons caused by non-observance of the safety instructions and improper use of the product.

• Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.

• Do not use the product for outdoor uses, the product is designed for indoor use.

• The product is intended for domestic use only.

• Do not use this product in a bathtub, shower, or water-lled reservoir.

• Do not immerse the product, the power cable or plug in water or other liquids.

• After the product has been immersed or covered in water or other liquids, do not use the product again.

• Keep the product away from heat sources. Do not place the product on hot surfaces or near open ames.

• Keep away from ammable gases, vapor or explosive dust.

• Keep distance from ammable objects.

• Do not open the product.

• High voltage! Do not touch the inner metal grid.

• Do not look directly into the light, this may cause eye damage.

• Never put metal objects inside the grid.

• Keep your hands away from the grid. Do not insert ngers, pencils or other objects through the guard.6

• Do not use the product in barns, stables and similar locations.

• Do not expose the product to water or moisture.

• Always disconnect the product from the power outlet before cleaning or moving the product.

• Do not drop the product and avoid bumping.

• Do not use the product for more than 8 hours a day, due to the radiation.

• Keep the product out of reach from children.

• Before use, always check that the mains voltage is the same as the voltage on the rating plate of the product.

• Children shall not play with the product.

• This product may only be serviced by a qualied technician for maintenance to reduce the risk of electric shock.

• Disconnect the product from the power outlet and other equipment if problems occur.

• Do not use the product when the cable or plug is damaged.

• Always unwind the power cable before using the product.

• Do not pull the power cable to move the product.

• Do not let the power cable hang over the edge of a table or counter.

• If necessary, use an earthed extension cable of a suitable diameter.

• Do not leave the product unattended when the product is connected to the power outlet.

• Before cleaning and maintenance, switch o the product and disconnect the power. Let the product cool down completely.

• Do not cover the product when in use.

• Do not use the product in barns, stables and similar locations.

• Do not use cleaning solvents or abrasives.

• Do not clean the inside of the product.

• Do not attempt to repair the product. If the product does not operate correctly, replace it with a new product. Installing the product (image A)

1. Hang the product with the chain ring A

2. Connect the power cable A

Always disconnect the product from the power outlet before cleaning or moving the product. Do not use cleaning solvents or abrasives. Do not attempt to repair the product. If the product does not operate correctly, replace it with a new product.Clean the outside of the product with a soft, clean, lightly damp cloth.Empty the tray A at least once a week.The LED lamp cannot be replaced.