MultiSync FE772M - Monitor NEC - Free user manual and instructions

USER MANUAL MultiSync FE772M NEC

Index1 TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING CAUTION RISK OF ELECTRIC SHOCK • DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICE- ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems. Canadian Department of Communications Compliance Statement DOC: This Class B digital apparatus meets all requirements of the Canadian Interference- Causing Equipment Regulations. C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No.950. FCC Information

Use the attached specified cables with the MultiSync FE772M color monitor so as not to interfere with radio and television reception. (1) Please use the supplied power cable or equivalent to ensure FCC compliance. (2) Please use the supplied shielded video signal cable. Use of other cables and adapters may cause interference with radio and television reception.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help. If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.2 Contents MultiSync FE772MTo learn about other special offers, register online at www.necdisplay.com. Your new NEC MultiSync

monitor box* should contain the following:

• MultiSync Monitor with tilt/swivel base

• Captive Signal Cable

• Remember to save your original box and packing material to transport or ship the monitor. Power Cord User’s Manual Captive Signal Cable FPO3 Quick Start Connecting the Tilt/Swivel stand

1. With the monitor unplugged from your system and the wall outlet, carefully

turn the monitor down on a firm table

2. Align the hooks on the tilt/swivel stand with the matching slots in the base of

3. Insert the hooks into slots.

4. Slide the tilt/swivel stand toward the front of the monitor until the latches click

into the locked position. NOTE: For correct use of monitor, completely attach tilt/swivel base to the monitor. NOTE: To avoid self injury or damage to the monitor, attach and remove tilt/ swivel base with care. CAUTION: Make certain that the tilt/swivel base is locked firmly into place before turning the monitor upright. Removing the Tilt/Swivel stand

1. With the monitor unplugged from

your system and the wall outlet, carefully turn the monitor upside down on a firm table.

2. Push down on the latch of the

tilt/swivel base and slide the tilt/swivel base backward from the front of the monitor.

3. Pull out the tilt/swivel base from

the slots on the bottom of the monitor. Slot Hook Latch Hook Firm Table4 Quick Start - continued To attach the MultiSync™ monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. If necessary, install the display card into your system. For more information,

refer to the display card manual.

3. For the PC: Plug the end of the video signal cable of the monitor in the video

signal connector of the computer. (Figure A.1). Tighten all screws. For the Mac: Connect the Macintosh cable adapter (not included) to the monitor connector on the Macintosh (Figure B.1). Attach the 15-pin mini D-SUB end of the video signal cable to the Macintosh cable adapter on the computer (Figure B.1). Tighten all screws. NOTE: To obtain the Macintosh cable adapter, call NEC Display Solutions of America, Inc. at (800) 632-4662.

4. Connect one end of the power cord to the MultiSync monitor and the other

end to the power outlet (Figure C.1). NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord.

5. Turn on the monitor and the computer.

NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.5 Figure A.1 15-pin mini D-SUB Captive Signal Cable 15-pin mini D-SUB Mac Adapter (Not Included) Captive Signal Cable Figure B.1 Figure C.1 Power Cord Power Outlet Quick Start - continued6 Use these buttons to choose or adjust items in the on screen display. MENU (or OSD) Button Use this button to enter or exit the on screen display. This Indicator lights up blue when the monitor operates normally. If the monitor is in DPMS (Energy Saving) mode, this indicator will flicker. Power (DPMS) Indicator Use this button to turn the monitor on or off. Power Button Use this button to enter a selection in the on screen display. SELECT (or SET) Button Buttons Control Function Controls OSD (On Screen Display) control buttons on the front of the monitor function as follows:7 Control Direct Access Function The Contrast and Brightness functions are also available in the On Screen Display (OSD) menu. Button Bring up Contrast adjustment

CONTROLS LOCKED/UNLOCKED

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button and

button for 3 seconds: the message "CONTROLS LOCKED" appears. You can unlock the OSD controls at any time by pushing the MENU button and

button for 3 seconds. The message "CONTROLS UNLOCKED" will appear.

CONTROLS UNLOCKEDCONTROLS LOCKED

Button Bring up Brightness adjustment

Allows you to select the suitable setting for Movies, Photos, etc. DV Mode TEXT PHOTO MOVIE NORMAL Controls - continued MODE DESCRIPTION TEXT For use with word processing, spreadsheets, etc. PHOTO This is to view pictures or images with high resolution. MOVIE This mode is best for watching DVDs, looking at still images that have a dark background or for playing games. NORMAL Normal mode.8 Screen Adjustment Making adjustments to the image size, position and operating parameters of the monitor is quick and easy with the On Screen Display Control system. A short example is quick and easy given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE: Allow the monitor to stabilize for at least 30 minutes before making image adjustments. Case 1 Case 2 Controls - continued To make adjustments in the On Screen Display, follow these steps:

1. Press the MENU (or OSD) Button, then the main menu of the OSD appears.

2. To access a control, use the p or q Buttons. When the desired icon is

Buttons to adjust the item to the desired level.

4. Accept the changes by pressing the SELECT (or SET) Button.

5. Exit the OSD by Pressing the MENU (or OSD) Button.9

Controls - continued To adjust the brightness and contrast of the screen Brightness Contrast Main menu Sub menu Reference The following table indicates all the On Screen Display control, adjustment, and setting menus. BRIGHTNESS/CONTRASTPOSITION V Position H Position SIZE V Size H Size SHAPE Tilt Side Pincushion S Pincushion Balance Parallelogram Trapezoid Top Corner Bottom Corner COLOR PRESET 6500K 9300K Temp R/G/B (User Control) SETUP Video Level Language OSD Time SPECIAL Degauss Recall Reset Moire H Moire V Moire To adjust the position of the screen To adjust the size of the screen To adjust the shape of the screen To customize the color of the screen To customize the screen status for a user’s operating environment To improve the clarity and stabil- ity of the screen : Adjustable10 Controls - continued Brightness To adjust the brightness of the screen. Contrast To adjust the contrast of the screen. Vertical Position To move image up and down. Horizontal Position To move image left and right. Vertical Size To adjust image height. Horizontal Size To adjust image width. Tilt To correct image rotation. Side Pincushion To correct a concave or convex bowing of the image. Side Pincushion Balance To correct the balance of both sides bowing. Parallelogram To correctly adjust the skew of the im- age. Trapezoid To correct geometric distortion. Top Corner Bottom Corner To correct an irregular distortion of the displayed image. H11 Controls - continued 6500K/ 9300K Select the screen color.

• 6500K: Slightly reddish white.

• 9300K: Slightly bluish white. Select the screen temperature which you prefer among reddish or bluish or any color in between. Set your own color levels. This item is used to select the monitor’s input signal level. The normal level used for most PCs is 0.7V. If the screen becomes suddenly washed-out or blurred, please select 1.0V and try again. To choose the language in which the control names are displayed. OSD Menus are available in 12 languages: English, German, French, Spanish, Italian, Swedish, Finnish, Portuguese, Korean, Chinese , Russian and Polish. Set the OSD time, i.e. the length of time a menu will remain on-screen before it shuts off automatically. Adjust the time to 5, 10, 20, 30 or 60 seconds. To manually demagnetize the screen to avoid showing incorrect images or colors. You can use this function to reload the modified parameters for screen display operation, as specified by the user after purchase: Position, Size, Side Pincush- ion, Side Pincushion Balance, Parallelo- gram, Trapezoid (These recalled options may differ depending on the mode selected: Preset, User, or New). If you don’t want to recall the monitor to these modified settings, use the but- ton to select CANCEL and then press the SELECT (or SET) button. PRESET TEMP RED GREEN BLUE VIDEO LEVEL LANGUAGE OSD TIME DEGAUSS RECALL

H12 Controls - continued This is to adjust the alignment of red and blue fields. Use to adjust the purity on the screen if the color appears uneven. CONVER- GENCE* PURITY* H13 Side Jacks Rear Panel Jacks Microphone Operation Using this jack reduces the length of cable needed to reach the PC's sound card. In order to use the MIC jack, use a cable (supplied) to plug into the rear of the monitor (MIC OUT) and into the MIC input jack of your sound card (if available). *LINE OUT A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of PC sound card has only Speaker Out, reduce the PC volume. NOTE: If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line Out using the card jumper of the program (Refer to the Sound Card Manual). Automatically mutes the speaker volume when the headphones are plugged in. Can be used instead of the built-in microphone. Headphone Jack Microphone Jack Connects to the *LINE OUT jack of the PC sound card. Connects to the microphone jack of the PC sound card. Audio In -Sky Blue Mic Out - Pink Audio Functions14 Use to mute audio source. Audio Mute Use these buttons to choose or adjust items in the on screen display. Control Function Button Brings up to the audio menu. Button

Audio Selection and Adjustment You were introduced to the procedure of selection and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the items shown in the main Menu. To make adjustments in the On Screen Display, follow these steps: Audio Functions15

Raises or lowers audio level. Raises or lowers treble level. Raises or lowers bass level. Changes levels of left/right speaker. Enables or disables microphone usage. : Adjustable Main menu Description VOLUMETREBLE BASS BALANCEMICROPHONE Audio Functions16 Recommended Use Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be harmful or fatal or may cause electric shock, fire or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall, causing serious damage to the monitor.

Keep the monitor away from high capacity transformers, electric motors and other devices such as external speakers or fans, which may create strong magnetic fields.

• If possible, position the monitor so that it is facing the east to minimize the effects of the earth’s magnetic field.

• Changing the direction of the monitor while it is powered on may cause image discoloration. To correct this, turn the monitor off for 20 minutes before powering it back on.

• When operating the monitor with its AC 125-240V worldwide power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. The power supply cord you use must have been approved by and comply with the safety standards of your country.

In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with this monitor. If a power cord is not supplied with this monitor, please contact your supplier.

• Do not place any objects onto the monitor and do not use the monitor outdoors. Cleaning Your Monitor A special coating is provided on the glass (CRT) surface of this monitor to reduce a reflection and static electricity on the glass surface. Due to the delicate coating on the glass surface, use a lint-free, non-abrasive cloth (cotton or equivalent) and a non-alcohol, neutral, non-abrasive cleaning solution to minimize dust. If the screen requires more than a light cleaning, apply a soft neutral detergent and water directly to a soft cloth and use it upon wringing water, to clean the glass surface. Clean your monitor regularly. CAUTION: The following agents will cause damage to the CRT when cleaning the glass surface: Ben- zene, thinner, acid/alkaline detergent, alcohol detergent, detergent with abrasive powder, detergent with anti-static agent, detergent for cleaning. Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

• Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.

• The power cable connector is the primary means of detaching the system from the power supply. The monitor should be installed close to a power outlet which is easily accessible.

• Handle with care when transporting. Save packaging for transporting. CAUTION17

• Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.

• Position your monitor no closer than 12 inches and no further away than 28 inches from your eyes. The optimal distance is 18 inches.

• Rest your eyes periodically by focusing on an object at least 20 feet away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a non-alcohol, neutral, non-abrasive cleaning solution to minimize dust.

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to minimize turning your head while you are typing.

• Get regular eye checkups. Ergonomics To realize the maximum ergonomics benefits, we recommend the following:

• Adjust the Brightness until the background raster disappears

• Do not position the Brightness control to its maximum setting

• Use the preset Size and Position controls with standard signals

• Use the preset Color Setting and Sides Left/Right controls

• Use non-interlaced signals with a vertical refresh rate between 70-85Hz for the MultiSync

• Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue due to insufficient contrast For more detailed information on setting up a healthy work environment, write the American National Standard for Human Factors Engineering of Visual Display Terminal Workstations – ANSI-HFS Standard No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa Monica, California 90406. Recommended Use - continued CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR:18 Picture Tube 17 inches (16.0 inches viewable) 90 degree deflection 0.25mm dot pitch AGARAS (Anti-Glare Anti-Reflective Anti-Static) coating Sync Input Horizontal Freq. 30 - 71kHz (Automatic) Vertical Freq. 50 - 160Hz (Automatic) Input Form Separate TTL, Positive/Negative Signal Input 15 pin D-Sub Connector Video Input Input Form Separate, RGB Analog, 0.7Vp-p/75 ohm, Positive Plug & Play DDC 2B Power Consumption Normal* ≤ 68W Stand-by/Suspend ≤ 15W DPM Off ≤ 5W Resolutions 640 x 480 @ 60Hz to 120Hz 800 x 600 @ 55Hz to 110Hz 832 x 624 @ 55Hz to 106Hz 1024 x 768 @ 55Hz to 87Hz 1152 x 864 @ 55Hz to 77Hz 1280 x 1024 @ 55Hz to 66Hz Max VESA 1280 x 1024 @ 66Hz Recommend VESA 1024 x 768 @ 85Hz Dimensions &Weight (with tilt/swivel stand) Width 400 mm / 15.8 inches Height 401mm / 15.8 inches Depth 411 mm / 16.2inches Net 15.0 kg / 33.0 lbs Power Input AC 100-240V~ 50/60Hz Current Rating 2.0A @ 100-240V Environmental Conditions Operating Conditions Temperature 0˚C to 40 ˚C Humidity 10 % to 90 % non-Condensing Storage Conditions Temperature -20˚C to 60 ˚C Humidity 10 % to 90 % non-Condensing Tilt/Swivel Stand Detached Signal cable Attached Power cord Detached Audio RMS Audio Output 1W + 1W (Right + Left) Input Sensitivity 0.7 Vrms Speaker Impedance 8Ω Specifications NOTE: Information in this document is subject to change without notice. *68K/85Hz, Cross Hatch, normal size.19 Features ClearFlat™ Shadow Mask CRT: Delivers an outstanding viewing experience with a virtually flat image, eliminating distortion and reducing glare so that what you see on-screen is as realistic and lifelike as what you see on your printed output. The patented ClearFlat CRT also offers a high contrast screen with a fine grille pitch, delivering crisp, clean text and graphics. AGARAS ( Anti-Glare, Anti-Reflective, Anti-Static Coating): Reduces reflection and glare and increases contrast without sacrificing focus level, clarity or brightness. Along with the flat square technology CRT, a high contrast screen delivers crisp, clean text and graphics. Invar Shadow Mask: Holes in the thin metal sheet behind the glass of the CRT surface correspond to each phosphor dot on the inner surface of the CRT’s faceplate, allowing the correct electron beam (red, green, blue) to hit the correct color phosphor for improved focus, brightness and color. Dual Dynamic Beam Focus: Provides precise, continuous focus adjustments of the electron beams and optimum image quality, even to the far edges of the screen. AccuColor

Control System: Allows you to change the color settings on your display to match your personal preference. OSD (On-Screen Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus. ErgoDesign

Features: Enhance human ergonomics to improve the working en- vironment, protect the health of the user and save money. Examples include OSD controls for quick and easy image adjustments, tilt/swivel base for preferred angle of vision and compliance with MPRII guidelines for lower emissions. Plug and Play: The Microsoft

solution with the Windows

95/98 operating system facilitates setup and installation by allowing the monitor to send its capa- bilities (such as screen size and resolutions supported) directly to your computer, automatically optimizing display performance. IPM

(Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emis- sions and lowering the air conditioning costs of the workplace. Reduced Magnetic Field

Technology: Reduces magnetic and alternating electric field emissions and static electricity, addressing ergonomic concerns regarding potential risks from extended computer monitor use. Multiple Frequency Technology: Automatically adjusts monitor to the display card’s scanning frequency, thus displaying the resolution required. FullScan

Capability: Allows you to use the entire screen area in most resolu- tions, significantly expanding image size.20 Troubleshooting No picture

• Display card should be completely seated in its slot.

• Power Button and computer power switch should be in the ON position.

• Signal cable should be completely connected to display card/computer and monitor.

• Check connector for bent or pushed-in pins. Image is scrolling or unstable

• Signal cable should be completely attached to the computer and monitor.

• Check pin assignments and signal timings of the monitor and your display card with respect to recommended timings and pin assignments.

• If the Macintosh cable adapter is used, check for proper connection or make sure the display card is Macintosh compatible and that the card is properly seated in the computer. LED on monitor is not lit (no blue color can be seen)

• Power Switch should be in the ON position and power cord should be connected. Picture is fuzzy or color looks blotchy

• Adjust Brightness and Contrast Controls.

• Access the Degauss Control through OSD controls. Activate the Degauss Control. CAUTION: A minimum interval of 20 minutes should elapse before the Deguass Control is used a second time when not switching between modes. Picture bounces or a wavy pattern is present in the picture

• Move electrical devices that may be causing electrical interference away from the monitor.

• See inside cover of User’s Manual for FCC information. Edges of the display image are not square

• Use the OSD Shape Controls to straighten the edges.

• If possible, position the front of the monitor facing east. Display image is not centered, too small, or too large

• Use the OSD Size and Position Controls to adjust the image. No Sound

• Check to see if speaker cable is properly connected.

• Check to see if mute is activated.

• Check to see if volume in OSM is set at minimum. Microphone not functioning

• Check to see if microphone cable is properly connected.

• Switch microphone and speaker connector.21 NEC Monitor Customer Service & Support Customer Service and Technical Support: (800) 632-4662 Fax: (800) 695-3044 Parts and Accessories/Macintosh Cable Adapter: (800) 632-4662 Warranty Information: www.necdisplay.com Online Technical Support www.necdisplay.com Sales and Product Information Sales Information Line: (888) 632-6487 Canadian Customers: (866) 771-0266, Ext#: 4037 Government Sales: (800) 284-6320 Government Sales email: gov@necdisplay.com Electronic Channels World Wide Web: www.necdisplay.com Product Registration: www.necdisplay.com European Operations: www.nec-display-solutions.com Drivers and Downloads www.necdisplay.com References22 NEC Display Solutions of America, Inc. (hereinafter “NEC DISPLAY SOLUTIONS”) warrants this Product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace (at NEC DISPLAY SOLUTIONS’ sole option) any part of the enclosed unit which proves defective for a period of three (3) years from the date of first consumer purchase. Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or refurbished and will meet specifications of the original parts or unit. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. This warranty is limited to the original purchaser of the Product and is not transferable. This warranty covers only NEC DISPLAY SOLUTIONS-supplied components. Service required as a result of third party components is not covered under this warranty. In order to be covered under this warranty, the Product must have been purchased in the U.S.A. or Canada by the original purchaser. This warranty only covers Product distribution in the U.S.A. or Canada by NEC DISPLAY SOLUTIONS No warranty service is provided outside of the U.S.A. or Canada. Proof of Purchase will be required by NEC DISPLAY SOLUTIONS to substantiate date of purchase. Such proof of purchase must be an original bill of sale or receipt containing name and address of seller, purchaser, and the serial number of the product. It shall be your obligation and expense to have the Product shipped, freight prepaid, or delivered to the authorized reseller from whom it was purchased or other facility authorized by NEC DISPLAY SOLUTIONS to render the services provided hereunder in either the original package or a similar package affording an equal degree of protection. All Products returned to NEC DISPLAY SOLUTIONS for service MUST have prior approval, which may be obtained by calling 1-800-632-4662. The Product shall not have been previously altered, repaired, or serviced by anyone other than a service facility authorized by NEC DISPLAY SOLUTIONS to render such service, the serial number of the product shall not have been altered or removed. In order to be covered by this warranty the Product shall not have been subjected to displaying of fixed images for long periods of time resulting in image persistence (afterimage effects), accident, misuse or abuse or operated contrary to the instructions contained in the User’s Manual. Any such conditions will void this warranty. NEC DISPLAY SOLUTIONS SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NEC DISPLAY SOLUTIONS PRODUCT OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. This Product is warranted in accordance with the terms of this limited warranty. Consumers are cautioned that Product performance is affected by system configuration, software, the application, customer data, and operator control of the system, among other factors. While NEC DISPLAY SOLUTIONS Products are considered to be compatible with many systems, specific functional implementation by the customers of the Product may vary. Therefore, suitability of a Product for a specific purpose or application must be determined by consumer and is not warranted by NEC DISPLAY SOLUTIONS. For the name of your nearest authorized NEC DISPLAY SOLUTIONS service facility, contact NEC Display Solutions of America, Inc. at 1-800-632-4662. Limited Warranty23 Disposing of your old NEC Products Within the European Union EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic products carrying the mark (left) must be disposed of separately from normal household waste. This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself and NEC. The mark on electrical and electronic products only applies to the current European Union Member States. Outside the European Union If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method. Declaration of the Manufacturer We hereby certify that the color monitors MultiSync

NEC DISPLAY SOLUTIONS

, vous devez d’abord obtenir une autorisation de retour de marchandise en composant le 1-800-632-4662. Le produit ne pourra avoir été enlevé ou modifié, réparé ou entretenu au préalable par personne d’autre que du personnel technique autorisé par

NEC DISPLAY SOLUTIONS

, et le numéro de série du produit ne pourra pas avoir été enlevé. Pour être couvert par cette garantie, le produit ne pourra pas avoir été soumis à l’affichage d’une image fixe pendant de longues périodes de temps résultant en une persistance de l’image, un accident, une utilisation incorrecte ou abusive ou une utilisation contraire aux directives contenues dans le guide de l’utilisateur. Une seule de ces conditions annulera la garantie.

NEC DISPLAY SOLUTIONS

NE POURRA ÊTRE TENUE RESPONSABLE DE DOMMAGES DIRECTS, INDIRECTS, ACCIDENTELS, SECONDAIRES OU D’AUTRES TYPES DE DOMMAGES RÉSULTANT DE L’UTILISATION D’UN PRODUIT QUI N’ENTRENT PAS SOUS LA RESPONSABILITÉ DÉCRITE CI-DESSUS. CES GARANTIES REMPLACENT TOUTE AUTRE GARANTIE EXPLICITE OU IMPLICITE, Y COMPRIS, MAIS SANS S’Y LIMITER, TOUTE GARANTIE DE QUALITÉ MARCHANDE OU D’APTITUDE À UNE FIN PARTICULIÈRE. CERTAINES JURIDICTIONS NE PERMETTANT PAS L’EXCLUSION DE GARANTIES IMPLICITES OU LA LIMITATION OU L’EXCLUSION DE RESPONSABILITÉ POUR DOMMAGES ACCI- DENTELS OU SECONDAIRES, LES EXCLUSIONS OU LIMITATIONS CI-DESSUS POURRAIENT NE PAS S’APPLIQUER DANS VOTRE CAS. Ce produit est garanti selon les termes de cette garantie limitée. Les consommateurs doivent savoir que les performances du produit peuvent varier selon la configuration du système, le logiciel, l’application, les données du client et la manière dont le produit est utilisé par l’opérateur, ainsi que d’autres facteurs. Bien que les produits

NEC DISPLAY SOLUTIONS

soient considérés compatibles avec de nombreux systèmes, la mise en oeuvre fonctionnelle du produit peut varier d’un client à l ’autre. Par conséquent, l’adéquation d’un produit à un besoin ou une application spécifique doit être déterminée par le con- sommateur et n’est pas garantie par

NEC DISPLAY SOLUTIONS

NEC de pièce HD67NM55000 Imprimé au TaiwanPROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Display Solutions of America, Inc. and/or its licensors, as appropriate, reserve all patent, copyright and other proprietary rights to this document, including all design, manufacturing, reproduction, use and sales rights thereto, except to the extent said rights are expressly granted to others. The NEC Display Solutions of America, Inc. product(s) discussed in this document are warranted in accordance with the terms of the Limited Warranty Statement accompanying each product. However, actual performance of each such product is dependent upon factors such as system configuration, customer data and operator control. Since implementa- tion by customers of each product may vary, the suitability of specific product configurations and applications must be determined by the customer and is not warranted by NEC Display Solutions of America, Inc. To allow for design and specification improvements, the information in this document is subject to change at any time without notice. Reproduction of this document or portions thereof without prior approval of NEC Display Solutions of America, Inc. is prohibited.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 500 Park Blvd, Suite 1100 Itasca, Illinois 60143 Tel. No.: (630) 467-3000 Type of Product: Display Monitor Equipment Classification: Class B Peripheral Model: MultiSync FE772M We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. NEC MultiSync™ Series Printed in China Part No.