SKMD30E3DS - Microwave Oven SHARP - Free user manual and instructions

USER MANUAL SKMD30E3DS SHARP

• Read all of the Installation Manual that is included with the Microwave Drawer before installing the extension kit.
• Observe all governing codes, ordinances, and safety instructions. • Be sure to leave these instructions with the consumer. Parts included: Left Side Trim (qty. 1)Right Side Trim (qty. 1) Mounting Brackets (qty. 2)Bracket Screws (qty. 8)Trim Screws (qty. 4) Install the extension kit after properly installing the microwave drawer in the cabinet. See steps below. Note that the side trims are marked "L" and "R" on the back side. TINSKB289MRR0 MICROWAVE DRAWER STANDARD MOUNT, MEASUREMENTS AND INSTALLATION INSTRUCTIONS

/32" (38.89 mm) door thicknessI. 15" (381 mm) auto drawer openingJ. 4" (101.60 mm)Figure 1E 2

1. Prepare cabinet opening as shown in Figure 2.

2. Place the drawer adjacent to the wall or cabinet opening. Plug the

power supply cord into the electrical outlet.

3. Carefully guide the drawer into the prepared opening. Avoid

contact with the sides of the cutout opening and pinching the cord between the oven and the wall.

4. Slidethedrawerallthewaybackuntilthesiderailsareushwith

the face of the cabinet.

5. Open the drawer. Using the 4 holes on the drawer as a template,

pre-drill the cabinet using a

/16" (1.6 mm) bit. Secure the drawer with the 4 screws supplied. See Figure 3. Side Rail Figure 3

6. Close drawer to complete oven installation. See Figure 4.

Figure 2 A. 6" (152.40 mm) B. Suggested electrical outlet location* C. Anti-Tip block D. 5" (127 mm) E. 3

/8" (561.98 mm) opening H. 14

/16" (376.24 mm) to bottom of Anti-Tip block

/8" (22.22 mm) overlap J. 23

/16" (11.11 mm) overlap L. 36" (914.40 mm) countertop height M. Allow

/8" (104.4 mm) minimum space P. 15

/16" (395.3 mm) opening Q. 30" (762.0 mm) minimum width Figures 1 and 2 contain many Microwave Drawer measurements for reference when planning the drawer’s location. This Microwave Drawer can be installed below any electric or gas wall oven.

• Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum

/2" diameter hole and deburred of all sharp edges.

7. Remove the 2 trim screws from each mounting bracket to begin

installation. Note: The mounting brackets come assembled to the side trims.

8. Open the drawer to properly align brackets to microwave side

rails. See Figure 5. BracketSide railsAlign sides and bottom of the 30" mounting brackets to the sides and bottomof the microwave drawer side rails Figure 5

9. Using the 4 holes on each bracket as a template, pre-drill the

/16" (1.6 mm) bit. Secure the mounting brackets to cabinet with the 8 bracket screws provided. See Figure 6. Figure 6

10. Place side trims on top of the mounting brackets, aligning the

screw holes. Note: Each side trim is marked "L" and "R" on the back side to indicate Left and Right.

11. Mount the Left and Right 30" trim extensions using the 4 trim

screws provided. See Figure 7.

1. Prepare cabinet opening as shown in Figure 2.

Figure 2 A. 6" (152.4 mm) B. Suggested electrical outlet location* C. Anti-Tip block D. 5" (127.0 mm) E. 3

/16" (376.2 mm) to bottom of Anti-Tip block

/32" (38.9 mm) Refer to Figure 3 ** J. 23

/8" (562.0 mm) L. Floor must support 100 lb (45.4 kg) M . 16

/4" (412.8 mm) opening

/8" (104.4 mm) Figures 1 and 2 contain many Microwave Drawer measurements for reference when planning the drawer’s location. This Microwave Drawer can be installed below any electric, gas wall oven, electric induction and/or gas cook tops.

• Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum

/2" diameter hole and deburred of all sharp edges.

Always allow sufcient power cord length to the electrical outlet to prevent tension. Always check electrical codes for requirements.

Top view Anti-Tip blockMounting cleat

Drawer face Trim face Note: the mounting surface of the finished cleat must sit 1

/32" (38.9 mm) back from the face of the cabinet.

/8" (596.9 mm) mounting cleat opening width B. 0"ush C. 1

/32" (38.9 mm) front of cleat to cabinet face Note: For pre-existing 30” cabinet openings that desire a standard mount,llerpanelswillneedtobeinstalledoneithersideofthe cutout to properly mount the extension kit panels.E 5

Front view No oven shown

Anti-Tip block Suggested electrical outlet location Figure 4 A. 22

/8" (562.0 mm) mounting cleat opening width B. 30

/8" (3.2 mm) from opening to top of shelf

2. Place the drawer adjacent to the wall or cabinet opening. Plug

the power supply cord into the electrical outlet.

3. Carefully guide the drawer into the prepared opening. Avoid

contact with the sides of the cutout opening and pinching the cord between the oven and the wall.

4. Slide the drawer all the way back until the side rails touch the

cleats mounted in the cabinet opening.

5. Open the drawer. Using the 4 holes on the drawer as a template,

pre-drill the cabinet using a

/16" (1.6 mm) bit. Secure the drawer with the 4 screws supplied. See Figure 5. Side Rail Figure 5

6. Close drawer to complete oven installation. See Figure 6.

7. Remove the 2 trim screws from each mounting bracket to begin

installation. Note: The mounting brackets come assembled to the side trims.

8. Properly align brackets to microwave side rails. See Figure 7.

BracketSide railsAlign sides and bottom of the 30" mounting brackets to the sides and bottomof the microwave drawer side rails Figure 7E 6

9. Using the 4 holes on each bracket as a template, pre-drill the

10. Place side trims on top of the mounting brackets, aligning the

screw holes. Note: Each side trim is marked "L" and "R" on the back side to indicate Left and Right.

11. Mount the Left and Right 30" trim extensions, using the 4 trim

Top view Anti-Tip blockMounting cleat

Front view No oven shown