MSZGL06NA - Air Conditioning MITSUBISHI - Free user manual and instructions

USER MANUAL MSZGL06NA MITSUBISHI

• To use this unit correctly and safely, be sure to read these operating in- structions before use.

• Since rotating parts and parts which could cause an electric shock are used in this product, be sure to read these “Safety Precautions” before use.• Since the cautionary items shown here are important for safety, be sure to observe them.• After reading this manual, keep it together with the installation manual in a handy place for easy reference.• Be sure to receive a guarantee card from your dealer and check that the purchased date and shop name, etc. are entered correctly. Marks and their meanings WARNING :Incorrect handling could cause serious hazard, such as death, serious injury, etc. with a high probability. CAUTION :Incorrect handling could cause serious hazard depending on the conditions. Meanings of symbols used in this manual : Be sure not to do. : Be sure to follow the instruction. : Never insert your fi nger or stick, etc. : Never step onto the indoor/outdoor unit and do not put anything on them. : Danger of electric shock. Be careful. : Be sure to disconnect the power supply plug from the power outlet. : Be sure to shut off the power. SAFETY PRECAUTIONS CONTENTS ■ SAFETY PRECAUTIONS 1

■ SPECIFICATIONS 10 WARNING Do not connect the power cord to an intermediate point, use an extension cord, or connect multiple devices to a single AC outlet.• This may cause overheating, fi re, or electric shock.Make sure the power plug is free of dirt and insert it securely into the outlet.• A dirty plug may cause fi re or electric shock.Do not bundle, pull, or modify the power cord, and do not apply heat or place heavy objects on it.• This may cause fi re or electric shock.Do not turn the breaker OFF/ON or disconnect/connect the power plug during operation.• This may create sparks, which can cause fi re.• After the indoor unit is switched OFF with the remote controller, make sure to turn the breaker OFF or disconnect the power plug. Do not expose your body directly to cool air for a prolonged length of time.• This could be detrimental to your health.The unit should not be installed, relocated, disassembled, altered, or repaired by the user.• An improperly handled air conditioner may cause fi re, electric shock, injury, or water leakage, etc. Consult your dealer.• If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard.When installing, relocating, or servicing the unit, make sure that no substance other than the specifi ed refrigerant (R410A) enters the refrigerant circuit.• Any presence of foreign substance such as air can cause abnormal pressure rise and may result in explosion or injury.• The use of any refrigerant other than that specifi ed for the system will cause mechanical failure, system malfunction, or unit break-down. In the worst case, this could lead to a serious impediment to securing product safety.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.Children should be supervised to ensure that they do not play with the appliance. Do not insert your fi nger, a stick, or other objects into the air inlet or outlet.• This may cause injury, since the fan inside rotates at high speeds during operation. In case of an abnormal condition (such as a burning smell), stop the air conditioner and disconnect the power plug or turn the breaker OFF.• A continued operation in the abnormal state may cause a malfunc-tion, fi re, or electric shock. In this case, consult your dealer.When the air conditioner does not cool or heat, there is a pos-sibility of refrigerant leakage. In this case, consult your dealer. If a repair involves recharging the unit with refrigerant, ask the service technician for details.• The refrigerant used in the air conditioner is safe. Normally, it does not leak. However, if refrigerant leaks and comes in contact with a heat source such as a fan heater, kerosene heater, or cooking stove, it will create a harmful gas.The user should never attempt to wash the inside of the indoor unit. Should the inside of the unit require cleaning, contact your dealer.• Unsuitable detergent may cause damage to plastic material inside the unit, which may result in water leakage. Should detergent come in contact with electrical parts or the motor, it will result in a malfunction, smoke, or fi re. JG79Y190H02_en.indd 1 2019/06/25 12:01:44En-2 SAFETY PRECAUTIONS CAUTION Do not touch the air inlet or the aluminum fi ns of the indoor/outdoor unit.• This may cause injury.Do not use insecticides or fl ammable sprays on the unit.• This may cause a fi re or deformation of the unit.Do not expose pets or houseplants to direct airfl ow.• This may cause injury to the pets or plants.Do not place other electric appliances or furniture under the indoor/outdoor unit.• Water may drip down from the unit, which may cause damage or malfunction.Do not leave the unit on a damaged installation stand.• The unit may fall and cause injury.Do not step on an unstable bench to operate or clean the unit.• This may cause injury if you fall down.Do not pull the power cord.• This may cause a portion of the core wire to break, which may cause overheating or fi re.Do not charge or disassemble the batteries, and do not throw them into a fi re.• This may cause the batteries to leak, or cause a fi re or explosion.Do not operate the unit for more than 4 hours at high humidity (80% RH or more) and/or with windows or outside door left open.• This may cause the water condensation in the air conditioner, which may drip down, wetting or damaging the furniture. • The water condensation in the air conditioner may contribute to growth of fungi, such as mold.Do not use the unit for special purposes, such as storing food, raising animals, growing plants, or preserving precision devices or art objects.• This may cause deterioration of quality, or harm to animals and plants.Do not expose combustion appliances to direct airfl ow.• This may cause incomplete combustion.Never put batteries in your mouth for any reason to avoid ac-cidental ingestion.• Battery ingestion may cause choking and/or poisoning.Before cleaning the unit, switch it OFF and disconnect the power plug or turn the breaker OFF.• This may cause injury, since the fan inside rotates at high speeds during operation.When the unit will be unused for a long time, disconnect the power plug or turn the breaker OFF.• The unit may accumulate dirt, which may cause overheating or fi re.Replace all batteries of the remote controller with new ones of the same type.• Using an old battery together with a new one may cause overheating, leakage, or explosion.If the battery fl uid comes in contact with your skin or clothes, wash them thoroughly with clean water.• If the battery fl uid comes in contact with your eyes, wash them thoroughly with clean water and immediately seek medical attention.Ensure that the area is well-ventilated when the unit is operated together with a combustion appliance.• Inadequate ventilation may cause oxygen starvation.Turn the breaker OFF when you hear thunder and there is a pos-sibility of a lightning strike.• The unit may be damaged if lightning strikes.After the air conditioner is used for several seasons, perform inspection and maintenance in addition to normal cleaning.• Dirt or dust in the unit may create an unpleasant odor, contribute to growth of fungi, such as mold, or clog the drain passage, and cause water to leak from the indoor unit. Consult your dealer for inspection and maintenance, which require specialized knowledge and skills.Do not operate switches with wet hands.• This may cause electric shock.Do not clean the air conditioner with water or place an object that contains water, such as a fl ower vase, on it.• This may cause fi re or electric shock.Do not step on or place any object on the outdoor unit.• This may cause injury if you or the object falls down. For installation WARNING Consult your dealer for installing the air conditioner. • It should not be installed by the user since installation requires spe-cialized knowledge and skills. An improperly installed air conditioner may cause water leakage, fi re, or electric shock.Provide a dedicated power supply for the air conditioner.• A non-dedicated power supply may cause overheating or fi re.Do not install the unit where fl ammable gas could leak.• If gas leaks and accumulates around the unit, it may cause an explosion.Ground the unit correctly.• Do not connect the ground wire to a gas pipe, water pipe, lightning rod, or a telephone ground wire. Improper grounding may cause electric shock. CAUTION Install a Ground Fault Interrupt (GFI) circuit breaker depending on the installation location of the air conditioner (such as highly humid areas).• If the Ground Fault Interrupt (GFI) breaker is not installed, it may cause electric shock.Ensure that the drain water is properly drained.• If the drain passage is improper, water may drip down from the indoor/outdoor unit, wetting and damaging the furniture.In case of an abnormal condition Immediately stop operating the air conditioner and consult your dealer. IMPORTANT Dirty fi lters cause condensation in the air conditioner which will contribute to the growth of fungi such as mold. It is therefore recommended to clean air fi lters every 2 weeks.JG79Y190H02_en.indd 2 2019/06/25 12:01:45● OPERATING INSTRUCTIONS ● En-3 Operation indicator lamp Remote control receiving section Emergency operation switch Page 5 Air inlet (back and side) Refrigerant piping Drainage hose Air outlet Drain outlet Horizontal vane Air outlet Air fi lter (Nano platinum fi lter) Air inlet Heat exchanger Front panel Outdoor unit

Indoor unit Remote controller Outdoor units may be different in appearance. Air cleaning fi lter (Anti-Allergy Enzyme Filter) Remote controller holder Signal transmitting section Distance of signal : About 20 ft. (6 m) Beep(s) is (are) heard from the indoor unit when the signal is received. Operation display section OFF/ON (stop/operate) button Temperature buttons Page 5 Operation select button Page 5 ECONO COOL button Page 7 FAN speed control button Page 6 Off-timer button Page 7 On-timer button Page 7 VANE control button Page 6 TIME set buttons Pages 4, 7 forward button backward button CLOCK button Page 4 RESET button Page 4 Lid Slide down to open

• Install the remote control-ler holder in a place where the signal can be received by the indoor unit. Only use the remote controller provided with the unit. Do not use other remote controllers. If two or more indoor units are installed in proximity to one another, an indoor unit that is not intended to be operated may respond to the remote controller. SMART SET button Page 6 Battery replacement indicator Page 4 JG79Y190H02_en.indd 3 2019/06/25 12:01:45En-4

• Make sure the polarity of the batteries is correct.

• Do not use manganese batteries and leaking batteries. The remote controller could malfunction.

• Do not use rechargeable batteries.

• The battery replacement indicator lights up when the battery is running low. In about 7 days after the indicator starts lights up, the remote controller stops working.

• Replace all batteries with new ones of the same type.

• Batteries can be used for approximately 1 year. However, batteries with expired shelf lives last shorter.

• Press RESET gently using a thin instrument. If the RESET button is not pressed, the remote controller may not operate correctly. Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on. Installing the remote controller batteries

PREPARATION BEFORE OPERATION

• Press CLOCK gently using a thin instrument. Setting current time Changing temperature units (°F→°C) Unit is preset with °F.

Press RESET while the temperature but- tons are pressed.

• Press RESET gently using a thin instrument.

• To change temperature unit from °C to °F, press RESET.

Press the TIME buttons to set the time. Each press changes the clock 1 minute forward/backward (10 minutes when pressed longer).

Insert the negative pole of AAA alkaline batteries fi rst. JG79Y190H02_en.indd 4 2019/06/25 12:01:46● OPERATING INSTRUCTIONS ● En-5 AUTO mode (Auto change over) The unit selects the operation mode according to the difference between the room temperature and the set temperature. During AUTO mode, the unit changes mode (COOL↔HEAT) when the room temperature is 4°F (2°C) away from the set tem-perature for more than 15 minutes.Note: Auto Mode is not recommended if this indoor unit is connected to a MXZ type out-door unit. When several indoor units are operated simultaneously, the unit may not be able to switch operation mode between COOL and HEAT. In this case, the indoor unit becomes standby mode (Refer to table of Operation indicator lamp). COOL mode Enjoy cool air at your desired temperature. Note: Do not operate COOL mode at very low outside temperatures (less than 14°F [-10°C]). Water condensed in the unit may drip and wet or damage furniture, etc. DRY mode Dehumidify your room. The room may be cooled slightly. Temperature cannot be set during DRY mode. HEAT mode Enjoy warm air at your desired temperature.Operation indicator lamp Emergency operation When the remote controller cannot be used...Emergency operation can be activated by pressing the emergency operation switch (E.O.SW) on the indoor unit.Each time the E.O.SW is pressed, the operation changes in the following order: Press

to start the operation. Press to select operation mode. Each press changes mode in the following order: Press or to set the temperature.Each press raises or lowers the temperature by 1°F (1°C). Press to stop the operation.• The same setting is selected the next time by simply pressing

Auto restart function If a power failure occurs or the main power is turned off during operation, “Auto restart function” automatically starts operation in the same mode as the one set with the remote controller just before the shutoff of the main power. When timer is set, timer setting is cancelled and the unit starts operation when power is resumed.If you do not want to use this function, please consult the service representative because the setting of the unit needs to be changed.

SELECTING OPERATION MODES

Set temperature : 75°F (24°C)Fan speed : MediumHorizontal vane : Auto(AUTO) (COOL) (DRY) (HEAT)Emergency COOLEmergency HEAT Stop Note:The fi rst 30 minutes of operation is test run. Temperature control does not work, and fan speed is set to High. Operation indicator lamp The operation indicator lamp shows the operation state of the unit.Indication Operation state Room temperatureThe unit is operating to reach the set temperatureAbout 4°F (2°C) or more away from set temperatureThe room temperature is approaching the set temperatureAbout 2 to 4°F (1 to 2°C) from set tem-peratureStandby mode (only during multi sys-tem operation) Lighted Blinking Not lightedNote: Multi system operation Two or more indoor units can be operated by one outdoor unit. When several indoor units are operated simultaneously, cooling and heating operations cannot be done at the same time. When COOL is selected with one unit and HEAT with another or vice versa, the unit selected last goes into standby mode. JG79Y190H02_en.indd 5 2019/06/25 12:01:47En-6

AIRFLOW DIRECTION ADJUSTMENT

Press to select fan speed. Each press changes fan speed in the following order:

• Two short beeps are heard from the indoor unit when set to AUTO.• Use higher fan speed to cool/heat the room quicker. It is recommended to lower the fan speed once the room is cool/warm.• Use lower fan speed for quiet operation. Note: Multi system operationWhen several indoor units are operated simultaneously for heating operation, the tem-perature of the airfl ow may be low. In this case, it is recommended to set the fan speed to AUTO. Press to select airfl ow direction. Each press changes airfl ow direction in the following order:
• Two short beeps are heard from the indoor unit when set to AUTO. Airflow direction (AUTO) ..........The vane is set to the most efficient airflow direction. COOL/ DRY:horizontal position. HEAT:position (5). (Manual).........For efficient air conditioning, select the upper position for COOL/ DRY, and the lower position for HEAT. If the position (4) or (5) is selected during COOL/DRY, the vane automatically moves to the upward position after 0.5 to 1 hour to prevent any condensation from dripping. (Swing)...........The vane moves up and down intermittently. ■ To change the horizontal airfl ow direction. Move the vertical vane manually before starting operation.

Press during COOL, ECONO COOL, or HEAT mode to select SMART SET mode.

Set the temperature, fan speed, and airfl ow direction.

The same setting is selected from the next time by simply pressing .• Two settings can be saved. (One for COOL/ECONO COOL, one for HEAT)• Select the appropriate temperature, fan speed, and airflow direction ac-cording to your room.• Normally, the minimum temperature setting in HEAT mode is 59°F (16°C). However, during SMART SET operation only, the minimum tem-perature setting is 50°F (10°C). Press again to cancel SMART SET operation.

• SMART SET operation also is cancelled when the MODE button is pressed. SMART SET operation A simplified set back function enables to recall the preferred (preset) setting with a single push of the button. Press the button again and you can go back to the previous setting in an instance.Example of use:1. Low energy modeSet the temperature 4°F (2°C) to 6°F (3°C) warmer in COOL and cooler in HEAT mode. This setting is suitable for unoccupied room, and while you are sleeping.2. Saving frequently used settingsSave your preferred setting for COOL/ECONO COOL and HEAT. This enables you to select your preferred setting with a single push of the button. (AUTO) (Quiet) (Low) (Med.) (High) (Super High) (AUTO) (1) (2) (3) (4) (5) (SWING) JG79Y190H02_en.indd 6 2019/06/25 12:01:48● OPERATING INSTRUCTIONS ● En-7

ECONO COOL OPERATION

Press during COOL mode page 5 to start ECO- NO COOL operation. The unit performs swing operation vertically in various cycles according to the temperature of airflow. Set temperature is set 4°F (2°C) higher automatically. Press again to cancel ECONO COOL operation.

• ECONO COOL operation is also cancelled when the VANE button is pressed. What is “ECONO COOL”? Swing airfl ow (change of airfl ow) makes you feel cooler than stationary airfl ow. So, even though the set temperature is automatically set at 4°F (2°C) higher, it is possible to perform cooling operation with keeping comfort. As a result, energy can be saved.

Press or during operation to set the timer. (ON timer) : The unit turns ON at the set time. (OFF timer) : The unit turns OFF at the set time.

• Make sure that the current time is set correctly. Page 4

Press (forward) and (backward) to set the time of timer. Each press changes the set time 10 minutes forward/backward.

• Set the timer while or is blinking.

Press or again to cancel timer. Note:

ON and OFF timers can be set together. mark indicates the order of timer operations. If power failure occurs while ON/OFF timer is set, see page 5 “Auto restart function”. TIMER OPERATION (ON/OFF TIMER) JG79Y190H02_en.indd 7 2019/06/25 12:01:50En-8 Instructions: CLEANING

• Switch off the power supply or turn off the breaker before cleaning.• Be careful not to touch the metal parts with your hands.• Do not use benzine, thinner, polishing powder, or insecticide.• Use only diluted mild detergents.• Do not expose parts to direct sunlight, heat, or fi re to dry.• Do not use water hotter than 120°F (50°C). Front panel 1. Lift the front panel until a “click” is heard.2. Hold the hinges and pull to remove as shown in the illustration above.• Wipe with a soft dry cloth or rinse it with water.• Do not soak it in water for more than two hours.• Dry it well in shade.3. Install the front panel by following the removal proce-dure in reverse. Close the front panel securely and press the positions indicated by the arrows. Hole Hinge Air cleaning fi lter (Anti-Allergy Enzyme Filter) Back side of air fi lter Every 3 months:• Remove dirt by a vacuum cleaner.When dirt cannot be removed by vacuum cleaning: Soak the fi lter and its frame in lukewarm water before rinsing it. After washing, dry it well in shade.Every year:• Replace it with a new air cleaning fi lter for best performance.• Parts Number MAC-408FT-E Pull to remove from the air fi lter Important• Clean the fi lters regularly for best performance and to re-duce power consumption.• Dirty fi lters cause condensation in the air conditioner which will contribute to the growth of fungi such as mold. It is therefore recommended to clean air fi lters every 2 weeks. Air fi lter (Nano platinum fi lter)
• Clean every 2 weeks • Remove dirt by a vacuum cleaner, or rinse with water.• After washing with water, dry it well in shade. What is “Nano platinum fi lter”? Nano platinum is a ceramic particle that includes a platinum nanoparticle. The particles are incorporated into the fi lter material, which results in providing semi-permanent antibacterial and deodorizing characteristics for the fi lter. Nano plati-num surpasses the catechin (a biofl avonoid that is found in green tea) in perfor-mance. Nano platinum fi lter uses this compound not only to improve air quality but also to eliminate bacteria and viruses. This air fi lter has a semi-permanent lasting effect even after washing it with water.JG79Y190H02_en.indd 8 2019/06/25 12:01:50● OPERATING INSTRUCTIONS ● En-9 Even if these items are checked, when the unit does not recover from the trouble, stop using the air conditioner and consult your dealer. Symptom Explanation & Check points Indoor Unit The unit cannot be operated.

• Is the breaker turned on?

• Is the power supply plug connected?

• Is the ON timer set? Page 7 The horizontal vane does not move.

• Are the horizontal vanes installed correctly?

• Is the fan guard deformed? The unit cannot be operated for about 3 minutes when restarted.

• This protects the unit according to instructions from the microprocessor. Please wait. Mist is discharged from the air outlet of the indoor unit.

• The cool air from the unit rapidly cools moisture in the air inside the room, and it turns into mist. The swing operation of the HORIZONTAL VANE is suspended for a while, then restarted.

• This is for the swing operation of the HORIZON- TAL VANE to be performed normally. The airfl ow direction changes during operation. The direction of the horizontal vane cannot be adjusted with the remote controller.

• When the unit is operated in COOL or DRY mode, if the operation continues with air blowing down for 0.5 to 1 hour, the direction of the airfl ow is automatically set to upward position to prevent water from condensing and dripping.

• In the heating operation, if the airfl ow temperature is too low or when defrosting is being done, the horizontal vane is automatically set to horizontal position. The operation stops for about 10 minutes in the heating operation.

• Outdoor unit is in defrost. Since this is completed in max.10 minutes, please wait. (When the outside temperature is too low and humidity is too high, frost is formed.) The unit starts operation by itself when the main power is turned on, but hasn’t received sign from the remote controller.

• These models are equipped with an auto restart function. When the main power is turned off without stopping the unit with the remote controller and is turned on again, the unit starts operation automatically in the same mode as the one set with the remote control- ler just before the shutoff of the main power. Refer to “Auto restart function” page 5 . The indoor unit discolors over time.

• Although plastic turns yellow due to the infl uence of some factors such as ultraviolet light and temperature, this has no effect on the product functions. Multi system The indoor unit which is not operating becomes warm and a sound, similar to water fl owing, is heard from the unit.

• A small amount of refrigerant continues to fl ow into the indoor unit even though it is not operating. When heating operation is selected, operation does not start right away.

• When operation is started during defrosting of outdoor unit is done, it takes a few minutes (max. 10 minutes) to blow out warm air. Outdoor Unit The fan of the outdoor unit does not rotate even though the compressor is running. Even if the fan starts to rotate, it stops soon.

• When the outside temperature is low during cool- ing operation, the fan operates intermittently to maintain suffi cient cooling capacity. Water leaks from the outdoor unit.

• During COOL and DRY operations, pipe or pipe connecting sections are cooled and this causes water to condense.

• In the heating operation, water condensed on the heat exchanger drips down.

• In the heating operation, the defrosting operation makes ice forming on the outdoor unit melt and drip down. White smoke is discharged from the outdoor unit.

• In the heating operation, vapor generated by the defrosting operation looks like white smoke. Symptom Explanation & Check points Remote controller The display on the remote controller does not appear or it is dim. The indoor unit does not respond to the remote control signal.

• Are the batteries exhausted? Page 4

• Is the polarity (+, -) of the batteries correct? Page 4

• Are any buttons on the remote controller of other electric appliances being pressed? Does not cool or heat The room cannot be cooled or heated suffi ciently.

• Is the temperature setting appropriate? Page 5

• Is the fan setting appropriate? Please change fan speed to High or Super High. Page 6

• Are the fi lters clean? Page 8

• Is the fan or heat exchanger of the indoor unit clean?

• Are there any obstacles blocking the air inlet or outlet of the indoor or outdoor unit?

• Is a window or door open?

• It may take a certain time to reach the setting temperature or may not reach that depending on the size of the room, the ambient temperature, and the like. The room cannot be cooled suffi ciently.

• When a ventilation fan or a gas cooker is used in a room, the cooling load increases, resulting in an insuffi cient cooling effect.

• When the outside temperature is high, the cooling effect may not be suffi cient. The room cannot be heated suffi ciently.

• When the outside temperature is low, the heating effect may not be suffi cient. Air does not blow out soon in the heating operation.

• Please wait as the unit is preparing to blow out warm air. Airfl ow The air from the indoor unit smells strange.

• Are the fi lters clean? Page 8

• Is the fan or heat exchanger of the indoor unit clean?

• The unit may suck in an odor adhering to the wall, carpet, furniture, cloth, etc. and blow it out with the air. Sound Cracking sound is heard. • This sound is generated by the expansion/con- traction of the front panel, etc. due to change in temperature. “Burbling” sound is heard. • This sound is heard when the outside air is ab- sorbed from the drain hose by turning on the range hood or the ventilation fan, making water fl owing in the drain hose to spout out. This sound is also heard when the outside air blows into the drain hose in case the outside wind is strong. Mechanical sound is heard from the indoor unit.

• This is the switching sound in turning on/off the fan or the compressor. The sound of water fl owing is heard.

• This is the sound of refrigerant or condensed water fl owing in the unit. Hissing sound is sometimes heard.

• This is the sound when the fl ow of refrigerant inside the unit is changed. In the following cases, stop using the air conditioner and consult your dealer.

• When water leaks or drips from the indoor unit.

• When the upper operation indicator lamp blinks.

• When the breaker trips frequently.

• The remote control signal is not received in a room where an electronic ON/OFF type fl uorescent lamp (inverter-type fl uorescent lamp, etc.) is used.

• Operation of the air conditioner interferes with radio or TV reception. An amplifi er may be required for the affected device.

• When an abnormal sound is heard.

• When any refrigerant leakage is found. WHEN YOU THINK THAT TROUBLE HAS OCCURRED JG79Y190H02_en.indd 9 2019/06/25 12:01:50En-10 Installation place Avoid installing the air conditioner in the following places.• Where there is much machine oil.• Salty places such as the seaside.• Where sulfi de gas is generated such as hot spring, sewage, waste water.• Where oil is splashed or where the area is fi lled with oily smoke (such as cooking areas and factories, in which the properties of plastic could be changed and damaged).• Where there is high-frequency or wireless equipment.• Where the air from the outdoor unit air outlet is blocked.• Where the operation sound or air from the outdoor unit bothers the house next door.• The mounting height of indoor unit 5.9 ft. to 7.5 ft. (1.8 m to 2.3 m) is recommended. If it is impossible, please consult your dealer. Electrical work
• Provide an exclusive circuit for the power supply of the air conditioner.• Be sure to observe the breaker capacity.If you have any questions, consult your dealer.

INSTALLATION PLACE AND

ELECTRICAL WORK SPECIFICATIONS To prevent the effects of a fl uorescent lamp, keep as far apart as possible.wall, etc.Inverter-type fl uorescent lampKeep a space to prevent the pic-ture distortion or the noise.3 ft. (1 m) or moreRadio4 in. (100 mm) or moreFor the optimum effi -ciency and to extend the life time of using, the outdoor unit should be installed in a well-ventilated dry place. Cordless phone or Portable phone10 ft. (3 m) or more 3 ft. (1 m) or moreThe installation location of the outdoor unit should be at least 10 ft. (3 m) away from the antennas for TV sets, radios, etc. In areas where the reception is weak, provide greater space between the outdoor unit and the antenna of the affected device if operation of the air conditioner interferes with radio or TV reception.

Set to the highest temperature in manual COOL mode, and operate for 3 to 4 hours. Page 5

• This dries the inside of the unit.• Moisture in the air conditioner contributes to favorable conditions for growth of fungi, such as mold.

to stop the operation.

Turn off the breaker and/or disconnect the power supply plug.

Remove all batteries from the remote controller. When using the air conditioner again:

Clean the air fi lter. Page 8

Check that the air inlet and outlet of the indoor and outdoor units are not blocked.

Check that the ground wire is connected correctly.

Refer to the “PREPARATION BEFORE OPERATION”, and follow the instructions. Page 4

WHEN THE AIR CONDITIONER IS NOT

GOING TO BE USED FOR A LONG TIME 8 in. (200 mm or more) Guaranteed operating range Indoor OutdoorCoolingUpper limit90°F (32.2°C) DB 115°F (46.1°C) DB73°F (22.8°C) WB —Lower limit67°F (19.4°C) DB 14°F (-10°C) DB57°F (13.9°C) WB —HeatingUpper limit80°F (26.7°C) DB 75°F (23.9°C) DB— 65°F (18.3°C) WBLower limit70°F (21.1°C) DB -4°F (-20°C) DB— -5°F (-20.6°C) WBDB : Dry BulbWB : Wet Bulb Note:

1. The guaranteed operating range value is for 1:1 System Application.

2. If the outdoor temperature is below the lower limit of guaranteed operating range, the out-

door unit may stop operation until the outdoor temperature exceeds the lower limit. JG79Y190H02_en.indd 10 2019/06/25 12:01:51● MANUAL DE INSTRUCCIONES ● Sp-1

MODE SMART SET (REGLAGE