Big Bang Unico Perpetual Calendar Sapphire 406.JX.0120.RT - Watch HUBLOT - Free user manual and instructions

USER MANUAL Big Bang Unico Perpetual Calendar Sapphire 406.JX.0120.RT HUBLOT

m = 311 ;

2018年/4月27日

2 Janvier

31-Janvier

2.过程

1. Mirs

2. 求导

20.1mol

1. DNA

28 Jun

27 Jullet

26 Aot

25 September

24 October

23 November

2016年4月1日

22 Dcembre

This function enables you to set the time using the crown positioned at 3 o'clock.

FONCTIONNEMENT

1. Loosen and pull the crown into position 2 (time-settling).
2. Tum the crown clockwise (locally) to set your watch to the desired time.
3. Push the crown back against the case, into position 1 (winding) and tighten the crown.

USING THE CHRONOGRAPH

INTRODUCTION

This function enables you to measure time using the two push-places positioned at 2 o'clock (Start/Stop) and 1 o'clock (React).

OPERATION

Before timing, make sure that the chronograph centre hand (direct drive), and the minute and hour counter hands have been reset. Then:

1. Press push-piece (A) : the chronograph hand will start instantly.
2. When the event ends, press push-piece (A): the hand will stop and display the exact elapsed time.
3. Press push piece (B) : the direct drive hand and counter hands will be reset.

To measure a series of sequential times : presspush-place ( A ) again to restart the hands. NB : the chronograph can only be reset if it hasfirst been stopped by pressing push-place ( A).

USING THE CALENDER

Adjuster tool

You can adjust the day, date, month and moon phase by pressing the adjusters positioned on the sides of the watch, using the adjuster tool supplied with your watch.

Four adjusters are built-in either side of the watch case, for adjusting the oscillator/oscillator settings.

ADJUSTED:

ADJUSTING THE MONTH/LEAP YEARPress on the adjuster posi

Each press turns the hand and the disc by one month.

ADJUSTING THE DATE Press on the adjuster positioned at 8 o'clock. Each press turns the hand by one day.

ADJUSTER C

ADJUSTER A

Press on the adjuster positioned at 2 o'clock.

Each press turns the disc by one day.

Time-setting position

Winding position

ADJUSTING THE DAY

Press on the adjuster positioned at 4 o'clock. Each press turns the hand by one day.

ADJUSTER

INSTRUCTIONS FOR ADJUSTMENT

1. Before making any adjustments, turn the crown clockwise (position 0). After turning the crown approx.30 times, the watch will be able to run automatically thanks to the movements of your wrist.
2. Pull the crown into position 1, then turn the hands clockwise until the date changes. The watch shows midnight. Continue and position the hands to 3 o'clock (3 am).
3. Press the adjuster A positioned at 2 o'clock several times until the full moon appears in the centre of the opening (at 6 o'clock). To adjust this function correctly, use the lunar calendar at the back of the Instruction manual to calculate the number of days since the last full moon. Next, press the adjuster the same number of times as the number of days since the last full moon.
4. Press the adjuster C at 8 o'clock several times until the date is positioned at 1.
5. Press the adjuster D at 9 o'clock several times until the required month is shown and the year is displayed inside the red zone on the dial (the loop year is indicated by the red number 4).

1. Press the adjuster C at 8 o'clock several times until the desired date is shown.
2. Press the adjuster B at 4 o'clock several times until the desired day is shown.
3. Turn the hands clockwise until the desired hour is shown (position 1). Then press the crown to return it to position 0, the movement begins to function. Tighten the crown.

PRECAUTIONS OF USE

• Do not attempt to lighten the crown when it is in the time-setting position; it must be returned to the winding position before being tightened.
  To guarantee that the watch runs constantly and regularly, you are recommended to stop the timer (using the push-pie at 2 o'clock) when the watch is not being worn or if the timer function is not being used.
• Do not make any adjustments between 8 pm and 1 am, or you will damage the mechanism.

CALENDRIER LUNAIRE (UTC*)

Showing the date of the full moon and leap years.

2016 *Leap year

24 Janvier

22 FeVJle

1. Miss

00:41

22 × 19

1. MHC

26 351

19 juillet

18Aoco

16 September

16 October

14 November

14 December

2017

12 Janvier

11 Favier

12 Mars

11 Avni

10Mai

9 Jun

9 Juillet

1. AouT

6 September

1. October

2. DNA

3.Darnpore

Cocnated U

2018

2 Janvier

31 Janvier

2 Mars

31 Mars

30 Avni

29 Mai

28 Jun

1. jiu1i:

26 Apr

25 September

24 October

1. November

2. December

2019

21Janvier

19Février

21 Mars

19 April

18Mai

1. Juin

2. lijiliet

15.40g/ L

149

107

10.10.10

12 November 2017

m - 1 0 ;

22 DecemB

2020 *Leap year

10 Janvier

1. Férrior

2. Mars

3. 甲组

② CO_2 : 溶液

7.1.1

13/14

8 July

3 Aou

2 September

1 Octob

31 Octobre

10 November

1. December

2021

28 Janvier

27 Fevrier

28 Mars.