DO9077KR - Food Processor DOMO - Free user manual and instructions

Technical Specifications	DOMO DO9077KR food processor, 1000 W power, 4.5 L bowl capacity, 6 speeds, pulse function.
Usage	Ideal for kneading, mixing, whipping, and emulsifying various ingredients. Included accessories: whisk, dough hook, blender.
Maintenance and Repair	Clean accessories by hand or in the dishwasher, regular motor maintenance recommended, check power cables.
Safety	Built-in safety system, overheating protection, non-slip feet for optimal stability during use.
General Information	Dimensions: 38 x 24 x 30 cm, weight: 3.5 kg, 2-year warranty, color: silver.

Frequently Asked Questions - DO9077KR DOMO

How do I assemble the DOMO DO9077KR?

To assemble the DOMO DO9077KR, start by attaching the bowl to the base. Then place the whisk or dough hook depending on the intended use. Make sure all accessories are properly in place before plugging in the device.

Why won\u0027t my robot start?

Check if the device is properly plugged into a working power outlet. Also ensure that the bowl and accessories are correctly installed, as the robot will not start if parts are not in place.

How do I clean the DOMO DO9077KR?

Unplug the device before cleaning. Removable accessories can be washed by hand or in the dishwasher. Wipe the robot base with a damp cloth. Never immerse the base in water.

What is the capacity of the DOMO DO9077KR bowl?

The DOMO DO9077KR bowl has a capacity of 4.5 liters, making it ideal for preparing large quantities of dough or mixtures.

Can I use the robot to knead bread dough?

Yes, the DOMO DO9077KR is equipped with a dough hook that allows easy kneading of bread dough. Make sure not to exceed the maximum bowl capacity.

The robot makes noise during use, is this normal?

A certain level of noise is normal during operation, especially at high speeds. However, if you hear unusual noises, check that all accessories are securely attached and in good condition.

How do I adjust the robot\u0027s speed?

The DOMO DO9077KR is equipped with a speed control. Turn the speed knob to select the desired speed based on the preparation you are making.

Where can I buy spare parts for the DOMO DO9077KR?

Spare parts for the DOMO DO9077KR can be ordered from DOMO customer service or authorized dealers. Also check online sales sites for specific parts.

Can the robot overheat?

Like any household appliance, the DOMO DO9077KR can overheat if used for long periods without interruption. It is recommended to take breaks after about 10 to 15 minutes of continuous use.

Is there a warranty on the DOMO DO9077KR?

Yes, the DOMO DO9077KR typically comes with a 2-year warranty. Keep your proof of purchase for any warranty claims.

USER MANUAL DO9077KR DOMO

Black and silver kitchen mixer with a control panel and digital display (no visible text or symbols)

DO9077KR

Handleiding Keukenrobot

Mode d'emploi Robot de cuisine

Gebrauchsanleitung Küchenmaschine

Instruction booklet Stand mixer

Manual de instrucciones Robot de cocina

Návod k použití Kuchyňský robot

GARANTIEVOORWAARDEN

CONDITIONS DE GARANTIE

This appliance has a two year warranty period. During this period the manufacturer is responsible for any failures that are the direct result of construction failure. When these failures occur the appliance will be repaired or replaced if necessary. The warranty will not be valid when the damage to the appliance is caused by wrong use, not following the instructions or repairs executed by a third party. The guarantee is issued with the original

till receipt. All parts, which are subject to wear, are excluded from the warranty.

If your device breaks down within the 2-year warranty period, you can return the device together with your receipt to the shop where you purchased it.

CONDICIONES DE GARANTÍA

RECYCLAGE-INFORMATIE

Simple line drawing of a trash bin with crossed lines indicating no waste or discharge (no text or symbols)

RECYCLING INFORMATIONEN

Recycling symbol composed of three chasing arrows forming a triangle (no text or labels)

RECYCLING INFORMATION

This symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it must be brought to the applicable collection point for recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

The packaging is recyclable. Please treat package ecologically.

Symbol of a trash bin crossed with two diagonal lines, representing no waste or discharge (no text or labels)

Recycling symbol with three arrows forming a triangle (no text or labels)

From now on, accessories and parts of Domo appliances can also be ordered online from the Domo webshop*:

http://webshop.domo-elektro.be

You can reach the webshop through the Domo website as well: www.domo-elektro.be. The accessories and parts can also still be obtained at the store where you bought the appliance.

* Enkel in België, Nederland, Luxemburg, Frankrijk en Duitsland.
* Seulement dans la Belgique, le Pays-Bas, le Luxembourg, la France et l'Allemagne.
* Nur in Belgien, die Niederlande, Luxemburg, Frankreich und Deutschland.

* Only in Belgium, the Netherlands, Luxemburg, France and Germany.

Simple black line drawing of a plug with a curved cable (no text or symbols)

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person in order to avoid a hazard.

Three black plastic mesh models labeled 10, 9, and 11, showing different mechanical components (no text or symbols on the shapes themselves)

Three metallic cylindrical mechanical components with attached brackets, labeled '14' below (no text or symbols on components)

Five different types of plastic containers, including a brush and cylindrical spools, arranged horizontally (no text or symbols visible)

Product photo showing various kitchen utensils and components including a motor, screwdriver, and filter (no text or labels visible)

Close-up of a mechanical component with no visible text or symbols

Close-up of a mechanical press or cutting machine component (no visible text or symbols)

Close-up of a mechanical device with a metallic component and tubing (no visible text or symbols)

Close-up of a metallic mechanical component with no visible text or symbols

Close-up of a modern smart water heater device with a logo, no visible text or symbols on the device itself.

Close-up of a mechanical device with a circular component and a rectangular housing (no visible text or symbols)

Close-up of a mechanical component with a metallic shaft and circular housing (no visible text or symbols)

Close-up of a mechanical device with a metallic component and a labeled part '4' (no readable text or symbols on the device itself)

Close-up of a mechanical component with circular and rectangular features, no visible text or symbols

Three metallic cylindrical containers with patterned lids, arranged horizontally (no text or symbols visible)

Close-up of a modern robotic device with a metallic top and control panel (no visible text or symbols)

Close-up of a mechanical device with a circular component and metallic casing (no visible text or symbols)

Close-up of a mechanical component with a metallic handle and internal cavity (no visible text or symbols)

Two metallic mechanical components: a gear-like shaft and a cross-shaped tool with a diamond-shaped hole (no text or symbols visible)

Close-up of three metallic pipe fittings and a mechanical component, no visible text or symbols

Three circular metal components with perforated surfaces, arranged horizontally (no text or symbols visible)

Close-up of a perforated metal object with a small hole, labeled '6' in the top right corner (no other text or symbols visible)

Close-up of a metallic gear or knob with a circular center and radial teeth (no text or symbols)

Close-up of a metal cutting tool with a baseplate and central handle (no visible text or symbols)

Black plastic mechanical component with a circular top and tapered shaft, labeled with number 9 (no text or symbols on the object itself)

Close-up of metallic mechanical components including a T-junction, helical spring, conical tip, and flange (no text or symbols visible)

Close-up of a mechanical component with a metallic shaft and flange (no visible text or symbols)

Collection of industrial kitchen components including a knitzer, screwdriver, plastic housing, and meshing (no text or symbols visible)

Close-up of a mechanical component with metallic shaft and flange (no visible text or symbols)

Three metallic mechanical components with threaded ends, displayed against a plain background (no text or symbols visible)

Close-up of a mechanical component with a circular aperture and mounting holes (no visible text or symbols)

BEREIDING PASTA

Basisrecept

Three black metal mesh head models labeled 10, 9, and 11, shown from different angles (no text or symbols on the models themselves)

1 2 3 4 5 6 7 8 DOMO

Three metallic mechanical components with no visible text or symbols, labeled '14' below (no other text or symbols)

Product lineup showing five cylindrical containers with different designs and accessories, labeled '12' (no text or symbols on containers)

Assorted kitchen components including a metal spatula, screwdriver, and various circular components (no text or symbols visible)

AVANT LE PREMIER USAGE

Pétrir/hacher/battre

Close-up of a mechanical component with metallic parts and a circular feature (no visible text or symbols)

Close-up of a mechanical component or tool with no visible text or symbols

Close-up of a kitchen sink with a metal handle and water outlet (no visible text or symbols)

Close-up of a metallic mechanical component with no visible text or symbols

Close-up of a modern robotic head with a metallic visor and logo (no visible text or symbols)

Close-up of a mechanical device with a circular component and a central hub (no visible text or symbols)

Close-up of a mechanical component with a metallic shaft and white circular end (no visible text or symbols)

Three-panel image showing a mechanical device with labeled parts: 4, 5, and 6 (no visible text or symbols)

Three-panel image showing a device with a sensor and internal components, no visible text or symbols.

Three views of a mechanical component: a spiral impeller, a cross-shaped tool, and a threaded pipe assembly (no text or symbols visible)

DO9077KR

Three circular metal components with perforated surfaces, arranged horizontally (no text or symbols visible)

Close-up of a perforated metal object with a numbered label '6' (no other text or symbols visible)

Close-up of a metallic gear or knob with six teeth, no visible text or symbols

Close-up of a metal mixing tool with a textured tray and central handle (no visible text or symbols)

Black plastic mechanical component with a circular top and tapered shaft, labeled with number 9 (no text or symbols on the object itself)

Close-up of metallic mechanical components including a cylindrical shaft, threaded fastener, and conical tip (no text or symbols visible)

Close-up of a mechanical component with metallic shaft and flange (no visible text or symbols)

Collection of industrial cutting gears and mechanical components (no text or symbols visible)

Close-up of a mechanical tool or device with metallic components and a black cylindrical component (no visible text or symbols)

Three metallic mechanical components with threaded ends, displayed on a plain surface (no text or symbols visible)

Close-up of a mechanical component with a circular aperture and metallic frame (no visible text or symbols)

Three black metal mesh models labeled 10, 9, and 11, showing different mechanical or architectural components (no text or symbols on the models themselves)

1 2 3 4 5 6 7 8 DOMO

Three metallic mechanical components with threaded ends, displayed against a plain background (no text or symbols visible)

Five different types of plastic containers, including a pen holder and cylindrical cups with textured surfaces (no text or symbols visible)

Collection of industrial kitchen components including a cutter, flourer, and pressure tool (no text or labels visible)

VOR DEM ERSTEN GEBRAUCH

Close-up of a metallic mechanical component with a circular feature, possibly a valve or knob (no visible text or symbols)

Close-up of a mechanical press or clamping device with metallic components and a tool (no visible text or symbols)

Close-up of a stainless steel kitchen sink with water pipes and a handle (no visible text or symbols)

Close-up of a metallic mechanical component with no visible text or symbols

Close-up of a modern robotic device with a transparent hood and control panel (no visible text or symbols)

Close-up of a mechanical device with a central circular component and a rectangular housing (no visible text or symbols)

Close-up of a mechanical component with a metallic shaft and white housing (no visible text or symbols)

Close-up of a mechanical device with a metallic component and a labeled part '4' (no visible text or symbols on the device itself)

Close-up of a mechanical component with metallic parts and mounting bracket (no visible text or symbols)

Three metallic cylindrical containers with patterned patterns, arranged horizontally (no text or symbols visible)

Close-up of a modern smart water heater device with metallic casing and control panel (no visible text or symbols)

Close-up of a mechanical device with a circular aperture and metallic frame (no visible text or symbols)

Close-up of a mechanical component with a metallic housing and a small cylindrical part inserted (no visible text or symbols)

Two mechanical components: a gear-like mechanical part and a cross-shaped metal tool (no text or symbols visible)

Close-up of three metallic pipe fittings and a mechanical component, no visible text or symbols

Three circular metal components with perforated surfaces, arranged horizontally (no text or symbols visible)

Close-up of a perforated metal component with a central hole and a label '6' (no text or symbols on the object itself)

Simple grayscale gear-like object with six teeth, no text or symbols visible

Close-up of a stainless steel robotic feeder with a cylindrical workpiece and a base (no visible text or symbols)

Black plastic mechanical component with a circular cap, shown against a white background (no text or symbols)

Close-up of metallic mechanical components including a conical tool, threaded shaft, and flange (no text or symbols visible)

Close-up of a mechanical component with metallic shaft and flange (no visible text or symbols)

Collection of industrial kitchen components including a T-shaped tool, threaded screw, plastic housing, and circular components (no text or symbols visible)

Close-up of a mechanical tool or device with a metallic handle and flanged base (no visible text or symbols)

Three metallic mechanical components with threaded ends, displayed against a plain background (no text or symbols visible)

Close-up of a mechanical device with a circular lens and rectangular frame (no visible text or symbols)

ZUBEREITUNG PASTA

Grundrezept

- 500g Mehl

• 4 Eier

- eine Prise Salz

• 2,5 ml Öl

• eventuell Wasser

This appliance may be used by children from the age of 8 and up, and also by persons with a physical or sensory limitation, as well as mentally limited persons or persons with a lack of experience and knowledge. But only on the condition that these persons have received the necessary instructions on how to use this appliance in a safe way and that they know the dangers that can occur by using this appliance.

Children cannot be allowed to play with the appliance. Maintenance and cleaning of the appliance may not be done by children, unless they are older than 8 years old and are under supervision.

Keep the appliance out of reach of children younger than 8 years old.

This appliance is suitable to be used in a household environment and in similar surroundings such as:

• Kitchen for personnel of shops, offices or other similar professional surroundings
• Farms
• Hotel or motel rooms and other surroundings with a residential character
• Guest rooms or similar

Attention: This appliance cannot be used with an external timer or a separate remote control.

1. Carefully read the instructions before using your appliance.
2. Switch off the appliance before fitting and removing the attachments.
3. Keep your fingers away from moving parts and the opening of the attachment.
4. Only use the appliance for its intended domestic use, the manufacturer will not accept any liability if the appliance is subject to improper use or failure to comply with these instructions.
5. Never leave the appliance to run unsupervised, especially when young children or handicapped persons are present.
6. Make sure that the voltage rating of the appliance does in fact match with that of your electrical system. Any connection error will nullify the guarantee.
7. The appliance must be plugged into an earthed electrical socket.
8. If you have to use an electrical extension lead, it must be earthed and placed in a way that no-one can trip over it.
9. Unplug the appliance as soon as you have finished using it and before cleaning.
10. Do not use your attachment and/or appliance if it has been damaged. You should contact an approved service centre.

11. Any work on the appliance other than normal care and cleaning by the customer must be carried out by an approved service centre.

12. Do not immerse the appliance, the power cord or the plug in water or any other liquid.

13. Do not allow the power cord to hang within the reach of children, to come close to or into contact with the hot parts of your appliance, any other source of heat or any sharp edge.
14. If the power cord or the plug is damaged, do not use your appliance. To avoid any risk, these must be replaced by an approved service centre.
15. Do not put any accessories containing metal in a microwave oven.
16. Switch off the appliance and disconnect from the power supply before changing accessories or approaching parts that move in use.
17. Do not touch the whisk, mixer blade or kneading hook while the appliance is operating.
18. Only use one attachment at a time.
19. Do not operate the appliance for more than 10 minutes at one time. Allow 30 minutes rest before the next use.
20. Do not use any other accessories than the ones delivered with the appliance or recommended by the manufacturer.

SPECIFICATIONS

220-240V\~50/60Hz 1000W

Speeds: OFF

1 - 8: speed control (min - max)

COMPONENTS

1. Speed control
2. Release button for multifunctional head
3. Connection accessories lid
4. Release button for lid accessories
5. Connection for accessories (under lid)
6. Mixing bowl lid
7. Stainless steel mixing bowl
8. Multifunctional head
9. Dough hook
10. Beater
11. Whisk

Three black metal mixing devices labeled 10, 9, and 11, shown side by side without any text or symbols on the devices themselves.

1 2 3 4 5 6 7 8 DOMO

1. Vegetable cutter with components

OPTIONAL ACCESSORIES

1. Meat grinder with components
2. Pasta set

Three metallic mechanical components with threaded ends, labeled '14' below (no text or symbols on components)

Product lineup showing four cylindrical containers with different patterns and sizes, one labeled '12' (no text or symbols on containers)

Assorted kitchen utensils including a cutter, screwdriver, and filter components (no text or symbols visible)

FIRST USE INSTRUCTIONS

Remove the unit and accessories from the packaging.

Wash all components with soap in warm water and dry carefully. Never immerse the engine unit in water, in order to prevent electrocution.

INSTALLATION AND USAGE

Kneading / grinding / beating

Depending on the nature of the ingredients, the mixing bowl and lid allow for the making of 2 kg of dough.

1. Make a quarter turn with the release button (2) to release the head, then push the head upward until you hear a click.

2. Put the bowl (7) on the base and turn it clockwise to tighten it. Place the ingredients in the bowl.

3. Select the preferred accessory: dough hook, beater or whisk.

a. Attach the hook to the head by moving it upward and sliding it around the shaft.

b. Turn the hook by a quarter in an anti-clockwise direction.

c. Position the hook so that it falls into the lock position.

Close-up of a metallic mechanical component with no visible text or symbols

Close-up of a mechanical component or tool with no visible text or symbols

Close-up of a mechanical component with no visible text or symbols

Close-up of a metallic mechanical component with no visible text or symbols

1. Turn back the release button (quarter turn) so that the head falls down. Push the head back into its original position until you hear a click.

2. Put the lid on the bowl with the opening at the front of the unit.

3. While it is operating, you can add ingredients through the opening in the lid.

4. In order to make the device stop, you turn the speed control to OFF.

5. Place the device on a clean and dry surface. Put the plug in the socket and select the desired speed by turning the speed control.

DISASSEMBLING

1. Remove the plug from the socket.

2. Remove the lid from the bowl.

3. Make a quarter turn on the release button, then push the head upwards until you hear a click.

4. Remove the hook from the lock position and turn it a quarter in a clockwise direction. Then slide the hook off the drive shaft and remove the hook. Remove the hook gently as accidents with sharp edges may occur.

5. Turn the bowl in an anti-clockwise direction from the lock position and remove the bowl.

6. Make a quarter turn backwards with the release button so that the head falls down. Then push the head back into its original position until you hear a click.

CLEANING

1. Always remove the plug from the socket before cleaning the device.
2. Never immerse the engine unit in a bowl of water or under running water. Clean the engine unit with a soft damp cloth.
3. Disassemble all accessories according to the user instructions in the section "Disassembling".
4. For quick cleaning, rinse the accessories under running water.
5. For thorough cleaning, wash, rinse and dry the accessories.

FITTING VEGETABLE SLICER DO907OKR-V

Turn the device off, and take the plug out of the socket before you add, remove or clean any accessories.

1. Open the lid by pressing the release button and push it upwards.
2. The connecting point for accessories is now shown.
3. Place the vegetable cutter at an angle of 25^ to the connection point and tighten it by making a quarter turn clockwise. You hear a click when it is securely fastened. Your vegetable cutter is now in a perfect vertical position.

Close-up of a modern smart device with a transparent hood and logo (no visible text or symbols)

Close-up of a mechanical device with a central circular component and metallic casing (no visible text or symbols)

Close-up of a mechanical component with a metallic shaft and circular housing (no visible text or symbols)

1. With the pushing rod you can safely place vegetables in the vegetable cutter.
2. Push the grater or slicer fully into the opening of the vegetable cutter.
3. You can choose between a cutter and two types of graters.

Close-up of a mechanical device with a metallic component and a flat top, labeled '4' in the corner (no readable text or symbols on the device itself)

Close-up of a mechanical component with circular flange and mounting bracket (no visible text or symbols)

Three metallic cylindrical containers with patterned lids, arranged horizontally (no text or symbols visible)

To remove the vegetable cutter, press the release button. Make a quarter turn clockwise on the vegetable cutter. Clean all parts thoroughly and dry carefully before using them again.

OPTIONAL ACCESSORIES: FITTING MEAT GRINDER DO907OKR-M

Turn off the device, and take the plug out of the socket before you add, remove or clean any accessories.

1. Open the lid by pressing the release button and pushing the lid upwards.
2. The connecting point for accessories is now shown.
3. Place the meat grinder at an angle of 25^ to the connection point and tighten it by making a quarter turn clockwise. You hear a click when it is securely fastened. Your meat grinder is now in a perfect vertical position.

Close-up of a modern stainless steel coffee maker with a logo, no visible text or symbols on the device itself.

Close-up of a mechanical device with a central circular component and a rectangular housing (no visible text or symbols)

Close-up of a mechanical component with a metallic handle and internal cavity (no visible text or symbols)

1. For grinding meat insert in succession: the worm wheel and the cutting knife.

Two metallic mechanical components: a gear-like mechanical part and a cross-shaped tool with a hexagonal hole (no text or symbols visible)

Three metallic pipe fittings and a mechanical component, shown from different angles (no text or symbols visible)

1. Then make a selection from the grinding discs: fine, medium or coarse.
2. Position the notch on the disc at the height of the projecting catch.
3. Connect it altogether with the screw ring.

Three circular metal components with perforated surfaces, arranged horizontally (no text or symbols visible)

Close-up of a perforated metal object with a small hole, labeled '6' in the corner (no other text or symbols)

Simple grayscale icon of a gear or knob with no text or symbols

1. Position the bowl in the best way possible so as to put your meat in it.
2. You can use the pushing rod to press the meat firmly inside.

Close-up of a stainless steel robotic feeder with a flat top and central hub (no visible text or symbols)

Black mechanical component with a circular top and tapered shaft, labeled '9' in the corner (no other text or symbols)

For sausage making, insert the following components:

Close-up of metallic mechanical components including a knuckle, threaded shaft, and conical end (no text or symbols visible)

Close-up of a mechanical component with a metallic shaft and flange (no visible text or symbols)

For making stuffed meatballs, insert the following components:

Close-up of various kitchen components including a knitted tool, threaded screw, plastic housing, and circular components (no text or symbols visible)

Close-up of a mechanical tool or pump component with metallic and black components (no visible text or symbols)

To remove the meat grinder, press the release button. Make a quarter turn clockwise on the meat grinder. Clean all parts thoroughly and dry carefully before using them again.

CLEANING

Do not use the dishwasher for cleaning the meat grinder.

OPTIONAL ACCESSORIES: PASTA DO907OKR-L-T-S

There are three accessories: a roller for lasagna, a tagliatelle cutter and spaghetti cutter.

To make spaghetti or tagliatelle, you must first use the lasagna roller to flatten sheets of pasta.

Three metallic cylindrical mechanical components with threaded ends, displayed against a plain background (no text or symbols visible)

Close-up of a mechanical device with a circular lens and rectangular frame (no visible text or symbols)

PREPARATION OF PASTA

Basic recipe

• 500 grams of flour
• 4 eggs
• a pinch of salt
• 2,5 ml oil
• optionally water

For whole-wheat pasta replace the regular flour with whole-wheat flour.

For pasta rossa replace one egg with 75 g tomato paste.

• Put the ingredients in the bowl.
• Mix with the dough hook n speed 1-2 for 2 to 3 minutes. Add water if the dough is too dry.
• Stop your food processor and knead the dough by hand until it is smooth.
• Let it rest in a kitchen towel for 15 minutes.
• Put the pasta roller into the connector for accessories.
• First, use the pasta roller to make flat sheets of pasta as for lasagna making.

• Enter these pasta sheets through the pasta cutter for spaghetti or tagliatelle.

• Fill a large pan full of water with a pinch of salt.

• Add some olive oil in order to prevent the pasta stick together
• Bring water to boil and add the pasta. Let simmer for 2 to 4 minutes depending on your personal preference.

CLEANING

Clean the pasta accessories with a damp cloth and wipe dry. Do not immerse in water or use the dishwasher for cleaning.

PRECAUCIONES IMPORTANTES

Three black metal mesh models labeled 10, 9, and 11, showing different mechanical or architectural features (no text or symbols on the models themselves)

1 2 3 4 5 6 7 8 DOMO

Three metallic mechanical components with no visible text or symbols, labeled '14' below (no other text or symbols)

Product display image showing four different types of plastic containers, one with a handle and three with textured lids (no text or symbols visible)

Collection of industrial kitchen components including a cutter, plunger, and filter (no text or symbols visible)

Close-up of a metallic mechanical component with no visible text or symbols

Close-up of a mechanical press or cutting machine component (no visible text or symbols)

Close-up of a kitchen sink with a metallic tool and tubing (no visible text or symbols)

Close-up of a metallic mechanical component with no visible text or symbols

Close-up of a modern smart device head with a logo, no visible text or symbols on the device itself.

Close-up of a mechanical device with a central circular component and metallic frame (no visible text or symbols)

Close-up of a mechanical component with a metallic shaft and white circular end (no visible text or symbols)

Close-up of a mechanical device with a metallic component and a labeled part '4' (no readable text or symbols on the device itself)

Close-up of a mechanical component with circular flange and mounting bracket (no visible text or symbols)

Three metallic cylindrical containers with patterned lids, arranged horizontally (no text or symbols visible)

Close-up of a modern stainless steel coffee maker with a lid and handle (no visible text or symbols)

Close-up of a mechanical device with a circular component and a metallic frame (no visible text or symbols)

Close-up of a mechanical component with a metallic housing and a small cylindrical part inserted (no visible text or symbols)

Two mechanical components: a threaded gear and a cross-shaped tool with a diamond-shaped hole (no text or symbols visible)

Three metallic pipe fittings and a mechanical component, shown from different angles (no text or symbols visible)

Three circular metal components with perforated surfaces, arranged horizontally (no text or symbols visible)

Close-up of a perforated metal component with a small hole, labeled '6' in the corner (no other text or symbols)

Close-up of a metallic gear or knob with a central hole and six teeth (no text or symbols visible)

Close-up of a metal cutting tool with a flanged base and central handle (no visible text or symbols)

Black plastic mechanical component with a circular top and tapered shaft, labeled with number 9 (no text or symbols on the object itself)

Collection of metallic mechanical components including a knuckle, worm gear, and a conical tool (no text or symbols visible)

Close-up of a metallic mechanical component with a pointed tip and cylindrical shaft (no visible text or symbols)

Collection of industrial kitchen components including a knitted tool, threaded screw, plastic housing, and circular components (no text or symbols visible)

Close-up of a mechanical tool or pump component with metallic and black components (no visible text or symbols)

Three metallic mechanical components with threaded ends, displayed on a plain surface (no text or symbols visible)

Close-up of a black mechanical component with a circular aperture and control buttons (no visible text or symbols)

Three black metal wire mesh models labeled 10, 9, and 11, showing different mechanical or architectural designs (no text or symbols on the models themselves)

1 2 3 4 5 6 7 8 DOMO

Three metallic mechanical components with threaded ends, labeled '14' below (no text or symbols on components)

Product lineup showing five different mechanical components with no visible text or labels

Collection of industrial kitchen components including a cutter, plunger, and filter (no text or symbols visible)

PŘED PRVNÍM POUŽITÍM

Close-up of a mechanical component with a metallic shaft and circular base (no visible text or symbols)

Close-up of a mechanical press or cutting tool in operation, showing no visible text or symbols

Close-up of a kitchen sink with a metal stand and water flowing (no visible text or symbols)

Close-up of a metallic mechanical component with no visible text or symbols

Collection of metallic mechanical components including a conical tool, threaded shaft, and flanged component (no visible text or symbols)

Close-up of a mechanical component with a metallic shaft and flange (no visible text or symbols)

Collection of industrial cutting tools including a T-shaped tool, helical screw, gear, and mechanical components (no text or labels visible)

Close-up of a mechanical tool or device with a metallic handle and central shaft (no visible text or symbols)

Three metallic mechanical components arranged on a plain surface (no text or symbols visible)

Close-up of a mechanical device with a circular lens and control buttons (no visible text or symbols)

PŘÍPRAVA

Two cylindrical white objects with small protrusions, possibly milk or similar beverage (no text or symbols visible)

Three product photos: square cards, a clear glass coffee maker, and a rectangular baking pan (no text or symbols visible)

of scan hier:

ou scannez ici:

oder hier scannen:

or scan here:

QR code image containing encoded data, no visible human-readable text