Ultrablend+ - Blender MOULINEX - Free user manual and instructions

USER MANUAL Ultrablend+ MOULINEX

Removable silicone gasket

Autoclean Program On LCD screen : “H” represents the last and highest speed (10 )

• Before using your appliance for the first time, hand-wash the parts that come into contact with food (jug, lid and measuring cap) in warm soapy water except for the motor unit.

ATTENTION: DO NOT IMMERSE THE MOTOR

UNIT/CONTROL PANEL OR PUT IT UNDER WATER OR ANY OTHER LIQUID. Clean with a damp cloth and dry it carefully. CAUTION: The blades are extremely sharp and not removable.

• Make sure all the packaging has been removed before operating the appliance.

• Do not operate the blender if the lid is not in place. CAUTION: the safety precautions are part of the appliance. Read them carefully before using your new appliance for the first time. Keep them in a place where you can find and refer to them later on.

USING YOUR APPLIANCE

• Put the appliance on a flat, stable, heat-resistant surface away from sources of heat or water splashes.

• Make sure the silicone gasket is in place on the motor unit. Position the jug correctly on the motor unit.

• Add the ingredients into the assembled jug without exceeding the maximum level indicated: 2L. It is recommended to half-fill the jug (1L) for foamy food.

• After making hot soup, wait until the jug cools down between 2 recipes.

• Less than 3 minutes of mixing are enough to blend liquids for most of the recipes.

• Lock the lid on the jug. Place the measuring cap in position on the lid and lock it by rotating it.

• To add ingredients while blending, remove the measuring cap from the lid and add the ingredients through the feeder hole. Beware of the risk of spatter. SM_BLENDER_HI-SPEED_8080016923.qxp_Mise en page 1 17/11/2016 09:11 Page1• Plug in the blender and press on the power button (7) a the bottom right of the appliance. The product makes a beep and the screen lights up in grey.

• Press on the Start button and the screen lights up in blue.

• Select your program or manual settings (time and speed) and press the start button. Wait for the blender to stop automatically. If you want to stop the blender before the automatic end of the program, press on the start button.

• Do not shake the motor unit or the jug when the blender is in use.

• When you use the pusher or the measuring cap, hold the jug by its handle to avoid it falling.

• When the blender is in use, do not use any other accessory than the pusher to avoid damaging the jug.

• Press on to turn off the screen. CAUTION: After running one cycle in the blender for the maximum processing time, let the blender rest for 1 minute before you operate it again. After using the blender for a maximum of two cycles, stop the appliance and leave to cool to ambient temperature (takes about 2 hours). Overload protection The appliance is equipped with overload protection. This prevents the motor from being damaged by overloading. If the appliance switches off during operation, proceed as follows : - Switch the appliance off using the power button, unplug and leave to cool down for approx.15-20 minutes. - Reconnect the appliance to the power supply and resume blending. 6 programs : Smoothie : The blender works at various speeds alternating for approx. 1 minute. Ice crush : Put max 8 ice cubes in the jug. The blender works in pulse intervals for approx. 1 minute. Hot soup : reheats and blends pre- cooked vegetables and broth thanks to the speed of blades. Sorbet : The blender works at speed 6 for approx. 1 minute. Nuts : The blender works at various speeds alternating for approx. 2 minutes.

• The pulse button can still be used when no program is running.

• Carrot soup : 800g pre-cooked carrots and 1,2L water for 3 min.

• Smoothie : 250g green apple with skin + 150g celery + 125g kiwi + 180g pear + 40g spinach + 225ml water +50g ice cube.

• Ice crush : 8 regular ice cubes.

• Hot soup : 450ml chicken stock + 120g double cream +300g courgette + 100g carrots + 50g celery + 30g green pepper. vegetables have to be pre- cooked.

• Sorbet (Strawberry Ice): : 450g frozen strawberries + 240ml milk + 130g caster sugar. Chill in the freezer until firm.

• Nut butter : 250g unsalted peanuts + 40g slivered almonds + 100g pecan nuts. CAUTION: Hard foods may mark the inside of the jug but this does not affect the efficiency of the appliance. Frozen foods must be smaller than a walnut. Do not add hot liquid above 80°C as it can be ejected out of the appliance due to a sudden build up of steam. SM_BLENDER_HI-SPEED_8080016923.qxp_Mise en page 1 17/11/2016 09:11 Page23

• Press on the power button and unplug the appliance.

• Empty the preparation, the jug is not meant for storing food in the refrigerator or freezer.

• To clean the motor unit, use a damp cloth. Dry it carefully.

• Never immerse the motor unit in water.

• For easy cleaning, wash the removable parts in water with few drops of washing-up liquid, immediately after use.

• The jug, lid and measuring cap can be cleaned in the dishwasher, but the gasket must not go in the dishwasher.

• Frequent cleaning in a dishwasher risks damaging the surface of the jug.

• For easy cleaning, you can use the “Clean program” : Put 150ml of water and 1 drop washing up liquid in the jug. The blender works at various alternating speeds for approx. 1 min 30.

AFTER USING YOUR APPLIANCE

WHAT TO DO IF YOUR APPLIANCE DOES NOT WORK ? Problems Causes Solutions Appliance does not work The plug is not connected.Connect the appliance to asocket with the same voltageas indicated on the ratingplate of the appliance.The blender jug is notpositioned correctly on themotor unit.Check that the blender jug ispositioned properly on themotor unit as explained in theinstructions.The power switch is on OFFposition.Follow the instructions forstarting your appliance.In case of software bug.Unplug the appliance, wait fewminutes and plug in again. The appliance stoppedwhile in useOverloadFollow the instructions insection Overload.The silicon gasket is missing ornot correctly positioned.Place the silicone gasketcorrectly on the motor unit.Excessive vibrationsThe product is not placed on aflat surface.Place the appliance on a flatsurface.Volume of ingredients is toohigh.Reduce the quantity ofingredients processed.The silicon gasket is missing ornot correctly positioned.Place the silicone gasketcorrectly on the motor unit. SM_BLENDER_HI-SPEED_8080016923.qxp_Mise en page 1 17/11/2016 09:11 Page34 Problems Causes Solutions Leak from the lid Volume of ingredients is too high. Reduce the quantity of ingredients processed. The lid is not correctly positioned Place the lid correctly on the blender jug. Leak from the bottom of the blender jug Deterioration of the watertightness of the appliance Caution : the blades are not removable. Contact the consumer service, see contact information in the warranty leaflet. The blades do not turn easily Pieces of food too large or too hard. Reduce the size or quantity of ingredients processed. The blended liquid is too hot and distorted the silicone gasket. Replace the gasket with a new one.

WERKEN MET HET APPARAAT