KA EL 1711 - Heating KALORIK - Free user manual and instructions

Product type	Oil-filled radiator
Brand	Kalorik
Model	KA EL 1711
Supply voltage	230 V ~
Minimum current required	10 A
Maximum power (estimated)	Up to 2300 W (with both switches)
Power settings	Switch I (low), switch II (medium), I+II (maximum)
Thermostat	Adjustable from 1 to 4 (or continuous), recommended position 4 for startup
Air humidifier	Built-in, removable tank with HIGH level, use demineralized water
Water tank capacity	Not specified, fill up to HIGH mark
Carrying handle	Yes, built-in
Casters and feet	4 casters + 2 feet to assemble with provided screws
Cable storage	Compartment provided on the appliance
Thermal safety	Safety thermostat with automatic reset after cooling
Material and oil	Steel body, filled with special oil (exact quantity, do not open)
Maintenance and cleaning	Unplug, clean with a soft damp cloth, do not immerse
Repairability	Repairs by qualified authorized service, do not open oil circuit
Authorized use	Indoor only, away from water (bathtub, shower, pool)
Weight	Not specified
Dimensions	Not specified

Frequently Asked Questions - KA EL 1711 KALORIK

How to assemble the feet of the Kalorik KA EL 1711 radiator?

Before first use, assemble the two provided feet using the screws already fixed under the appliance. Unscrew the screws, place the foot and screw back. Never use the radiator without the feet assembled.

How to use the built-in air humidifier?

Fill the removable tank with demineralized water up to the HIGH level. Remove the tank and its support, open the lid, fill, close and put back in place. Caution: the tank may be hot if the radiator is running.

What do switches I and II mean?

Switch I corresponds to low power, switch II to medium power, and by pressing both (I+II) you get maximum power. The switches are illuminated.

How to adjust the temperature?

Set the thermostat to position 4, turn on the appliance, then after 10-15 minutes adjust the thermostat according to your comfort by turning the knob towards + (warmer) or - (cooler).

What to do in case of overheating or automatic shutdown?

The radiator is equipped with a thermal safety device that automatically cuts power in case of overheating. Remove the cause (obstruction, etc.), wait 5 to 10 minutes for it to cool down, then restart. If the problem persists, contact after-sales service.

Can I cover the radiator with a cloth?

No, never cover the radiator with a cloth or any other object, as it could cause overheating and fire risk. Air must be able to circulate freely.

How to clean the radiator?

Always unplug the appliance before cleaning. Use a soft damp cloth, do not immerse the appliance in water or any other liquid.

What to do in case of oil leakage?

Any oil leakage must be reported immediately and the appliance should no longer be used. Contact a qualified competent service for repair.

Can I use an extension cord?

The manual does not recommend using an extension cord. Plug directly into a grounded wall outlet. Make sure the outlet is not in the flow of hot air.

How to dispose of the radiator at the end of its life?

Do not dispose of the appliance with household waste. Take it to a collection point for electrical and electronic waste (WEEE) in accordance with Directive 2002/96/EC. The oil must be treated separately.

USER MANUAL KA EL 1711 KALORIK

Technical line drawings of mechanical components including a rod, housing, and bearing (no text or labels)

☐ Please read these instructions carefully before using the appliance.
☐ Check that your mains voltage corresponds to that stated on the rating plate of the appliance before using the appliance.
☐ Never leave the appliance unsupervised when in use. Keep out of reach of children or incompetent persons.
From time to time check the appliance for damages. If it is damaged, do not use it but have it repaired by a competent qualified electrician (*). Should the cord be damaged, it must be replaced by a competent qualified electrician(*).
☐ Only use the appliance for domestic purposes and in the way indicated in these instructions.
☐ Never immerse the appliance in water or any other liquid for any reason whatsoever. When cleaning the appliance, refer to the instructions in the "Cleaning and care" section.
☐ Never use the appliance near hot surfaces.
□ Unplug the appliance before cleaning it.
☐ Never use the appliance outside and always place it in a dry environment.
☐ Never use accessories that are not recommended by the producer. They could constitute a danger to the user and risk to damage the appliance.
☐ Do not place the appliance under a power socket. The power socket must not be in the hot airflow of the appliance in order to avoid overheating.
☐ Never move the appliance by pulling the cord. Make sure the cord cannot get caught in any way. Do not wind the cord around the appliance and do not bend it.
□ Always position the radiator in such a way that inflammable materials (such as curtains) cannot be ignited. Ensure at all times that the unit is placed solidly on its wheels.
Make sure that the air inlet and outlet openings are not blocked. To avoid any risk of fire, do not cover the heater (ex. With clothes)
☐ Warning: Do not operate the heater near baths, showers, washbasins, swimming pools or any other water container. It must be impossible to reach the commands of your appliance when you are in contact with water.
☐ The temperature of the appliance may be very high when the appliance is in use. Avoid contact with the skin.
☐ Make sure the cord does not come into contact with the hot parts of the appliance.
□ Never use the appliance near inflammable or explosive materials.
☐ Do not cover the appliance in order to avoid any risk of fire.
☐ Hazards may occur, for instance when touching the radiator or knocking it over, or as a result of inappropriate positioning. No responsibility is accepted if damage results from improper use, or if these instructions are not complied with.
□ Always switch off and remove the plug from the wall socket after use, and also in case of any malfunction and before cleaning. Do not attempt to remove the plug from the wall socket with wet hands.
☐ This radiator is filled with a precise quantity of special oil. Any repairs requiring the opening of the oil container are to be made by the manufacturer or its authorized service agent. They also should be contacted if oil leaking.
☐ When scrapping the appliance, all regulations concerning the disposal of oil should be followed.

(1) Competent qualified electrician: after sales department of the producer or importer or any person who is qualified, approved and competent to perform this kind of repairs in order to avoid all danger. In any case you should return the appliance to this electrician.

CONNECTION TO THE MAINS SUPPLY

The radiator should only be connected to an earthed socket installed in accordance with the regulations.

Make sure that the supply voltage corresponds with the voltage marked on the rating label (230V (AC)) and the rated electric current is not lower than 10A. This product complies with all binding CE- labelling directives.

START UP

Before using the radiator for the first time, the feet must be fitted to the base of the unit and then secured with the screws provided.

Technical line drawings of mechanical components including a rod, housing, and wheel (no text or labels)

When the appliance is switched on for the first time, a slight smell may be emitted. Please ensure sufficient ventilation.

USAGE

Your appliance is fitted with an air humidifier (on the opposite side of the control panel). Before switching on your appliance, fill the water tank (with demineralized water). Do not overfill over the HIGH level.

How to fill the tank:

• Remove the tank and its support from the heater
• Remove the tank from its support
• Open the lid and fill the tank
• Close the lid, replace the tank on its support

Replace everything on the heater.

CAUTION: IF YOU WANT TO FILL THE TANK DURING USE PAY ATTENTION NOT TO GET BURNED BECAUSE IT BECOMES VERY HOT.

1. There are two indicator light switches; you can adjust them on your requirement.

Switch positions

I = reduced power
II = medium power
I+II = full power

1. Turn the thermostat to position 4 and switch on your appliance (1 or 2 switches).

8 KA EL 17-7/9/11 - 060626

1. After 10-15 minutes, if you feel the room temperature is too low or too high, just adjust the temperature to the desired position.
2. If you want to switch off your appliance, turn off the two power switches at the same time (the indicator light will be off), remove the plug from the power supply and place it in its storage location. CAUTION: YOUR APPLIANCE WILL REMAIN HOT FOR A FEW MINUTES.
3. To move your appliance, take it by its handle, raise it and roll it.

OVERHEAT PROTECTION

This heater is protected with an overheat protection that switches off the appliance automatically in case of overheat. In this case, unplug the appliance, wait about 10 minutes for it to cool. Then switch it back on as described above. The appliance should operate normally. Should the problem persist, please contact the nearest customer service.

GENERAL CLEANING AND CARE

• Before cleaning the appliance, ensure it is disconnected from the power supply and has cooled down completely.
• Do not clean the radiator with water and do not immerse it.
  • The housing may be wiped with a slightly damp, lint-fee cloth.

PROTECTION OF THE ENVIRONMENT- DIRECTIVE 2002/96/EC

In order to preserve our environment and protect human health, the waste electrical and electronic equipment should be disposed of in accordance with specific rules with the

implication of both suppliers and users. For this reason, as indicated by the symbol , the rating label or on the packaging, your appliance should not be disposed of as unsorted municipal waste. The user has the right to bring it to a municipal collection point performing waste recovery by means of reuse, recycling or use for other applications in accordance with the directive.

MODE D'EMPLOI

POUR VOTRE SECURITE

Technical line drawings of mechanical components including shaft, housing, and wheel (no text or labels)

Technical line drawing of mechanical components including shaft, housing, and bearing (no text or symbols)

I+II = maximum stand

Technical line drawings of mechanical components including shaft, housing, and bearing (no text or labels)

Technical line drawing of mechanical components including shaft, housing, and wheel assembly (no text or labels)

Technical line drawings of mechanical components including shaft, housing, and wheel (no text or labels)