ZGG 643 ICA - Cooker ZANUSSI - Free user manual and instructions

USER MANUAL ZGG 643 ICA ZANUSSI

Electrolux Home Products Belgium

of door ELECTROLUX SERVICE.

Electrolux Home Products Belgium

Consumer services 02/363.04.44 02/363.04.00

ELECTROLUX HOME PRODUCTS Tel: Fax:

Electrolux Home Products Belgium

ELECTROLUX HOME PRODUCTS Tel: Fax:

E-mail: consumer-service.luxembourg@electrolux.lu34

ENGLISH During Operation • This appliance has been designed for non professionalpurpose in private houses only. It is meant to cook edible foodstuff only and MUST NOT be used for any other purposes. • It is dangerous to alter the specification in any way. • For hygiene and safety reasons, this appliance shouldbe kept clean at all times. A build-up of fats or otherfoodstuff could result in a fire.• Under no circumstances should you attempt to repairthe appliance yourself. Repairs carried out byunexperienced persons may cause injury or seriousmalfunctioning. Refer to your local Service Centre.Always insist on genuine spare parts.• Ensure that all control knobs are in the OFF positionwhen not in use.• Should you connect any electrical tool to a plug near thiscooking appliance, ensure that electric cables are not incontact with it and keep them far enough from the heatedparts of this appliance.• If the appliance is out of order, disconnect it from theelectric supply. Child Safety • This appliance has been designed to be operated byadults and children under supervision. Young children MUST NOT be allowed to tamper with the controls or play near or with the oven.• This appliance is not intended for use by children orother persons whose physical, sensory or mentalcapabilities or lack of experience and knowledgeprevents them from using the appliance safely withoutsupervision or instruction by a responsible person toensure that they can use the appliance safely.• Accessible parts of this appliance may become hot when it is in use. Children should be KEPT AWAY until it has cooled. About Installation, Cleaning and

Manteinance • It is mandatory that all operations required for theinstallation are carried out by a qualified or competentperson, in accordance with existing rules and regulations.• Disconnect the appliance from the electrical supply,before carrying out any cleaning or manteinance work.• Ensure a good ventilation around the appliance. A poorair supply could cause lack of oxygen.• Ensure that the gas supply complies with the gas typestated on the identification label, placed near the gassupply pipe. These warnings are provided in the interest of safety. You MUST read them carefully before

installing or using the appliance.

Important Safety Information • This appliance is not connected to a combustionproducts evacuation device. It must be installed andconnected in accordance with current installationregulations. Particular attention shall be given to therelevant requirements regarding ventilation.• The use of a gas cooking appliance results in theproduction of heat and moisture in the room in whichit is installed. Ensure that the kitchen is well ventilated:keep natural ventilation holes open or install amechanical ventilation device (mechanical extractorhood).• Prolonged intensive use of the appliance may call foradditional ventilation, for example opening of a window,or more effective ventilation, for example increasingthe level of mechanical ventilation where present.• Once you removed all packaging from the appliance,ensure that it is not damaged and the electric cable is inperfect conditions. Otherwise, contact your dealer beforeproceeding with the installation.• The manufacturer disclaims any responsabilityshould all the safety measures not be carried out. Service • Under no circumstances should you attempt to repairthe appliance yourself. Repairs carried out byunexperienced persons may cause injury or seriousmalfunctioning. Refer to your local Service Centre.Always insist on genuine spare parts. Environmental Information • After installation, please dispose of the packaging withdue regard to safety and the environment.• When disposing of an old appliance, make it unusable,by cutting off the cable.• The symbol on the product or on its packagingindicates that this product may not be treated ashousehold waste. Instead it shall be handed over tothe applicable collection point for the recycling ofelectrical and electronic equipment. By ensuring thisproduct is disposed of correctly, you will help preventpotential negative consequences for the environmentand human health, which could otherwise be causedby inappropriate waste handling of this product. Formore detailed information about recycling of thisproduct, please contact your local city office, yourhousehold waste disposal service or the shop whereyou purchased the product.35

It is most important that this instruction

book should be retained with the appliance

for future reference. Should the appliance

be sold or transferred, always ensure that

the book is left with the appliance in order

that the new owner can get to know the

functions of the appliance and the relevant

warnings. These instructions are only for the countriesstated by the symbol printed on the front coverof this instruction book.This appliance complies with thefollowing E.E.C. Directives:- 2006/95 (Low Voltage Directive);- 89/336 (Electromagnetical CompatibilityDirective);- 93/68 (General Directives)and subsequent modifications.MANUFACTURER:ELECTROLUX ZANUSSI S.p.A.Viale Bologna, 29847100 FORLÌ (Italie) Guide to Use the instructions The following symbols will be found in the text to guideyou throughout the Instructions:Safety InstructionsStep by step instructions for an operationHints and TipsEnvironmental information !

Instruction for the User 36

Cleaning and Maintenance 37

Declaration of guarantee terms 43

European guarantee 44

Electrical Connection 39

Adaptation to different types of gas 40

Hob burners control knobs

The hob burners control knobs are situated on the hob

right hand side. The symbols on the knobs mean that :

" there is no gas supply

there is maximum gas supply

there is minimum gas supply

Lighting the burners

For easier lighting, proceed before putting a

pan on the pan support.

To light a burner, turn the relevant knob anticlockwise

to maximum position and push down the knob to

After lighting the flame, keep the knob pushed

down for about 5 seconds. This will allow the

"thermocouple" (Fig. 1 lett. B) to be heated and the

safety device to be switched off, otherwise the gas

supply would be interrupted. Then, check the flame

is regular and adjust it as required.

If you cannot light the flame even after several

attempts, check the "cap" (Fig. 1 lett. A) is in the

To put the flame out, turn the knob to the symbol ".

• Always turn the flame down or put it out before

taking the pans off the burner.

Using the hob correctly

To ensure maximum burner efficiency, it is strongly

recommended that you use only pots and pans with a

bottom fitting the size of the burner used, so that flame

will not spread beyond the bottom of the vessel (see the

It is also advisable, as soon as a liquid starts boiling, to

turn down the flame so that it will barely keep the liquid

• Use only pans or pots with flat bottom.

Carefully supervise cookings with fats or oil, since

these types of foodstuff can result in a fire, if over-

Small (Auxiliary) 80 mm. 160 mm.

Instruction for the User

Disconnect the appliance from the electrical

supply, before carrying out any cleaning or

Wash the enamelled components with warm soapy

water. Never use abrasive cleaners.

Frequently wash the "caps" and the "crowns" with hot

soapy water, carefully taking away any built-up of food.

The pan supports are dishwasher proof.

If the marks are particularly difficult to remove, use

common non-abrasive cleaners or specific products.

Never use steel wool pads or acids.

Regularly wipe over the hob top and the aluminium

frame using a soft cloth weel wrung out in warm water

to which a little liquid detergent has been added. Avoid

the use of the following:

- household detergent and bleaches;

- impregnated pads unsuitable for non-stick saucepans;

- bath/sink stain removers.

Should the hob top become heavily soiled, it is

recommended that a proper cleaning product is used.

The electric ignition is obtained through a ceramic

"candle" and a metal electrode (fig. 1 lett. C). Keep these

components well clean, to avoid difficult lighting, and

check that the burner crown holes (lett. A) are not

The cap and the crown of each burner are secured with

two screws. To separate the two pieces, lift the cap,

turn it upside down, then undo the two fixing screws

After a thorough cleaning, reassemble the two parts

and refit the cap in its correct position on the burner.

If scratches or cracks are noticed, disconnect

the appliance from the electrical supply to

avoid the risk of electric shock and call your

nearest Electrolux Service Centre.

Periodic maintenance

Periodically ask your local Service Centre to check the

conditions of the gas supply pipe and the pressure

adjuster, if fitted.

To ensure the good operation of the hob and its safety

features, it is necessary that the taps are periodically

" The periodic lubrication of the taps must be

carried out by qualified personnel, which you

must refer to also in case of malfunctioning.

Cleaning and Maintenance

Gas connection G 1/2"

Electric Supply 230 V 50 Hz

HOB RECESS DIMENSIONS Length 550 mm.

" The following instructions about installation

and maintenance must be carried out by qualified

personnel in compliance with the regulation in

force. The regulation to be applied for this type

of installation is NBN D 5I.003 : "Installations

functioning with combustible gas lighter than

" The side walls of the unit in which the hob is

going to be installed, must not exceed the height

" Avoid installing the appliance in the proximity of

inflammable materials (e.g. curtains, tea towels

" The appliance must be electrically disconnected

before all interventions. If any electric supply to

the appliance is required to carry out the work,

ensure all the necessary precautions are

It is indispensible that the connection to the gas mains

are carried out by means of an AGB tap. Choose fixed

connections or use a flexible pipe in AGB (stainless

If using flexible metallic pipes, be careful they do not

come in contact with mobile parts or they are not

squeezed. Use the same attention when the hob is

combinated with an oven.

This hob can be operated by Slochteren gas (G25) with

a nominal pressure of 25 mbar or by natural gas with

nominal pressure of 20 mbar. No regulation is required

for use by these two types of gas.

Before fitting the appliance ensure that the installation

has the correct voltage for the appliance. At full

capacity, the drop in pressure must not exceed 5%.

Such a drop in pressure is caused by the following

- maximum capacity of meter;

- diameter and lenght of the tube in front and behind

- section of transit of variuos tubes positioned on the

- diameter of eventual connections.

IMPORTANT - To ensure a correct operation, a saving

of energy and the long-life of the appliance, the voltage

pressure of the appliance must correspond to the

The adjustable connection is fixed to the comprehensive

ramp by means of a threaded nut G 1/2".

All the components shown in Fig.4 have already been

assembled in the factory.

The appliance, before leaving the factory, has been

tested in order to give you the best results.

IMPORTANT - When the final connection has been

made, it is essential that a thorough leak test is carried

out on the hob and installation. Use some soapy water,

Instruction for the Installer39

The appliance is designed to be connected to 230 V

monophase electricity supply.

The connection must be carried out in compliance with

the laws and regulations in force.

Before the appliance is connected:

1) check that the main fuse and the domestic installation

can support the load (see the rating label);

2) check that the power supply is properly earthed in

compliance with the current rules;

3) check the socket or the double pole switch used for

the electrical connection can be easily reached with

the appliance built in the forniture unit.

The appliance is supplied with a connection cable. This

has to be provided with a proper plug, able to support the

load marked on the identification plate. To connect the

plug to the cable, follow the recommendation given in

Fig. 5. The plug has to be fitted in a proper socket.

If connecting the appliance directly to the electric

system, it is necessary that you install a double pole

switch between the appliance and the electricity supply,

with a minimum gap of 3 mm. between the switch

contacts and of a type suitable for the required load in

compliance with the current rules.

The connection cable has to be placed in order that, in

each part, it cannot reach a temperature higher than

The brown coloured phase cable (fitted in the terminal

block contact marked with "L") must always be connected

to the network phase.

Replacement of the voltage

Only cable type H05V2V2-F T90 must be used. The

cable section must be suitable to the voltage and the

working temperature.

The yellow/green earth wire must be approximately 2

cm. longer than the phase wires (Fig. 5).

Fig. 5 FO 0073 Neutral

Earth (yellow/green)

Electrical Connection40

Injectors replacement

• Remove the pan supports.

• Remove the burner's caps and crowns.

• With a socket spanner 7 unscrew and remove the

injectors (Fig. 6), and replace them with the ones

required for the type of gas in use (see table 2).

• Reassemble the parts, following the same procedu-

• Replace the rating label (placed near the gas supply

pipe) with the relevant one for the new type of gas

supply. You can find this label in the package of the

injectors supplied with the appliance.

Should the feeding gas pressure be different or

variable compared with the required pressure, an

appropriate pressure adjuster must be fitted on the gas

supply pipe, in compliance with the rules in force.

Adjustment of minimum level

To adjust the minimum level of the burners, proceed as

• Turn the knob on the minimum position.

• With a thin screwdriver, adjust the by-pass screw

positioned in the centre of the gas tap control shaft

(see Fig. 7). If changing from natural gas to LPG,

completely tighten clockwise the screw, until a small

regular flame is obtained.

• Finally check the flame does not go out when quickly

turning the knob from the maximum position to the

This procedure can easily be carried out, anyhow the

hob has been positioned or built in the working top.

BURNER NORMAL REDUCED NORMAL POWER POWER POWER

Adaptation to different types of gas

These hobs can be inserted in a built-in kitchen unit

whose depth is between 550 and 600 mm. The hobs

dimensions are shown in Fig. 9.

The edge of the cut out must have a minimum distance

from the rear wall of 55 mm.

If there are side walls, or sides of the furniture unit near

the hob, the cut out edges must have a minimum

Hanging forniture units or hoods must be placed at 650

mm. minimum from the hob.

Fitting the hob to the worktop

Before fitting the hob into the cut out, an adhesive seal

must be fitted to the underside outside edge (Fig. 9) of

the hob. It is essential that no gaps are left in this seal

in order to prevent spillage near the hob seeping into

1) Remove the pan supports, the burners caps and

crowns and turn the hob upside down, taking care the

ignition candles are not damaged in this operation.

2) Place the sealing gasket all around the glass top

edge as shown in Fig. 9.

3) Place the hob in the cut out, taking care that it is

centred. Fix the hob with the relevant fixing clamps,

supplied with the injectors kit (Fig.10). When the screws

have been tightened, the excess seal can be removed.

A = Auxiliary burner

SR = Semirapid burner

Dimensions are given in

b) Space possibly useful for connections

Possibilities for insertion

Kitchen unit with door

Proper arrangements must be taken in designing the

forniture unit, in order to avoid any contact with the

bottom of the hob which can be heated when it is

operated. The recommended solution is shown in Fig.

The panel fitted under the hob should be easily

removable to allow an easy access if a technical

assistance intervention is needed.

Kitchen unit with oven

The hob recess dimensions must comply the indication

given in Figs. 12 and 13 and must be provided with

brackets to allow a continuous supply of air.

To avoid overhating, the building in should be carried

out as shown in Figs. 14 e 15.

The hob's electric connection and the oven's one must

be carried out separately, both for safety reasons and

to allow the oven to be easily taken off the unit.

Declaration of guarantee terms

Our appliances are produced with the greatest of care.

However, a defect may still occur. Our consumer services

department will repair this upon request, either during or

after the guarantee period. The service life of the appliance

will not, however, be reduced as a result.

This declaration of guarantee terms is based on

European Union Directive 99/44/EC and the provi-

sions of the Civil Code. The statutory rights that the

consumer has under this legislation are not affected

by this declaration of guarantee terms.

This declaration does not affect the vendor’s statutory

warranty to the end user. The appliance is guaranteed

within the context of and in adherence with the following

1. In accordance with provisions laid down in

paragraphs 2 to 15, we will remedy free of charge

any defect that occurs within 24 months from the

date the appliance is delivered to the first end user.

These guarantee terms do not apply in the event of

use for professional or equivalent purposes.

2. Performing the guarantee means that the appliance

is returned to the condition it was in before the defect

occurred. Defective parts are replaced or repaired.

Parts replaced free of charge become our property.

3. So as to avoid more severe damage, the defect must

be brought to our attention immediately.

4. Applying the guarantee is subject to the consumer

providing proof of purchase showing the purchase

and/or delivery date.

5. The guarantee will not apply if damage caused to

delicate parts, such as glass (vitreous ceramic),

synthetic materials and rubber, is the result of

6. The guarantee cannot be called on for minor faults

that do not affect the value or the overall reliability of

7. The statutory warranty does not apply when defects

- a chemical or electrochemical reaction caused by

- abnormal environmental conditions in general,

- unsuitable operating conditions,

- contact with harsh substances.

8. The guarantee does not apply to defects due to trans-

port which have occurred outside of our

responsibility. Nor will the guarantee cover those

caused by inadequate installation or assembly, lack

of maintenance or failure to respect the assembly

instructions or directions for use.

9. Defects that result from repairs or measures carried

out by people who are not qualified or expert or

defects that result from the addition of non-original

accessories or spare parts are not covered by the

10. Appliances that are easy to transport may be

delivered or sent to the consumer services

department. Home repairs are only anticipated for

bulky appliances or built-in appliances.

11. If the appliances are built-in, built-under, fixed or

suspended in such a way that removing and

replacing them in the place where they are fitted

takes more than half an hour, the costs that result

therefrom will be charged for. Connected damage

caused by these removal and replacement

operations will be the responsibility of the user.

12. If, during the guarantee period, repairing the same

defect repeatedly is not conclusive, or if the repair

costs are considered disproportionate, in agreement

with the consumer, the defective appliance may be

replaced with another appliance of the same value.

In this event, we reserve the right to ask for a financial

contribution calculated according to the length of

time it has been used.

13. A repair under guarantee does not mean that the

normal guarantee period will be extended nor that a

new guarantee period begins.

14. We give a twelve month guarantee for repairs, limited

15. Except in the event where liability is legally imposed,

this declaration of guarantee terms excludes any

compensation for damage outside the appliance for

which the consumer wishes to assert his rights. In

the event of legally admitted liability, compensation

will not exceed the purchase price paid for the

These guarantee terms are only valid for appliances

purchased and used in Belgium. For exported appliances,

the user must first make sure that they satisfy the

technical conditions (e.g.: voltage, frequency, installation

instructions, etc.) for the country concerned and that they

can withstand the local climatic and environmental condi-

tions. For appliances purchased abroad, the user must first

ensure that they meet the qualifications required in

Belgium. Non-essential or requested adjustments are not

covered by the guarantee and are not possible in all cases.

Our consumer services department is always at your

disposal, even after the guarantee period has expired.

Address for our consumer services department:

BELGIUM Electrolux Home Products Belgium

Consumer services 02/363.04.44 02/363.04.00

This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period

specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries

listed below the appliance guarantee will move with you subject to the following qualifications:

• The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of

a valid purchase document issued by the seller of the appliance.

• The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new country

of residence for this particular model or range of appliances.

• The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user.

• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home,

i.e. is not used for commercial purposes.

• The appliance is installed in accordance with all relevant regulations in force within your new country of residence.

The provisions of this European Guarantee do not affect any of the rights granted to you by law.45464735674-0551 06/07 - R.0

Grafiche MDM - Forlì