HL 940 - Four TEKA - Free user manual and instructions

USER MANUAL HL 940 TEKA

Simplified Instructions for Use

da luz do visor entre as 00:00 e as 6:00

ENGLISH Control Panel

For other markets, accessories may not correspond to those described in this manual.

It is used for sponges and cakes where the

heat received must be uniform to achieve a

Conventional with fan

Appropriate for roasts and cakes. The fan

spreads the heat uniformly inside the oven.

Grill and Lower element

Special for roasts. It can be used for any

piece, whatever its size.

Allows greater surfaces to be prepared, than

with the grill, together with higher power

reducing the time required for browning of the

For preparing dishes with superficial roasting.

It allows the outer layer to be browned without

affecting the inside of the food. Ideal for flat

food, such as steaks, ribs, fish, toast.

Heats only from beneath. Suitable for heating

dishes and raising pastry and similar.

Special for cooking pizzas, pastry and fruit

The fan distributes the heat produced by an

element located at the rear of the oven. Due to

the uniform heat distribution, it allows roasting

and baking to take place at two heights at the

This function uses a two-level hot air system.

LO is for fish, cakes, pastries and bread. HI

(higher temperature inside the oven) is for

After using this cleaning cycle, any traces of

grease or dirt that were stuck to the walls of

the oven can easily be wiped clean with a

The light remains on when performing any cook-

The electronic clock features Touch-Control

technology. To operate, simply touch the glass

control symbols with your fingertip.

The touch control sensitivity continuously

adapts to ambient conditions. Make sure the

glass surface of the control panel is clean and

free of obstacles when plugging in the oven.

If the clock does not respond correctly when

you touch the glass, unplug the oven for a few

seconds and then plug it in again. Doing this

causes the sensors to adjust automatically so

that they will react once more to fingertip con-

Electronic Clock Settings

Symbol : lights up during the TEKA Hydroclean® function.

Symbol : lights up when the clock timer

Symbol : lights up to indicate that the

Symbol : indicates that the oven is trans-

mitting heat to the food.

+ / – Sensors : enable you to select a time.

Sensors , and : enable you to

programme the electronic clock functions.

• When you turn on the oven, you will see the

clock flashing 12:00.

• Set the clock by touching the + or – sensor.

You will hear 2 beeps confirming that the

• To change the time, press the + and – sen-

sors at the same time. The current time will

then flash on the screen. Change the time

by pressing the + or – sensors. Two beeps

will then confirm that the new time has

NOTE The clock light has a night mode so the dis-

play light will dim between 00:00 and 6:00

• After setting the clock, the oven is ready for

use. Select a cooking function and temp-

• During cooking, symbol will light up to

indicate that heat is being transmitted to

• This symbol turns itself off when the selec-

ted temperature has been reached.

• Set the controls to to turn off the oven.

CAUTION After cooking, you will notice that the oven

cooling system is still on. This is normal and

is used to cool the oven down quickly.

3172465-002 EPIFA.QXD:- 20/10/11 08:02 Página 1920

Timer Alarm: The alarm will go off at the pro-

grammed time, even if the oven has finished

Cooking Time: This function allows you to pro-

gramme the cooking time, after which the

oven will turn off automatically.

Cooking Stop Time: This setting allows you to

programme the time for cooking to stop, after

which the oven will turn off automatically.

Cooking Time and Cooking Stop Time: This

setting allows you to programme the cooking

time and cooking stop time. The oven switches

on automatically at the set time and operates

for the selected cooking time (Cooking Time).

It then switches off automatically at the indi-

cated time (Cooking Stop Time).

Child Safety Function. This function locks the

electronic clock, preventing small children

from playing with it.

Help with the oven-cleaning function.

Programming the Timer Alarm

1. Touch sensor with your fingertip until

symbol starts flashing on the display.

The clock will also flash 00:00.

2. Select the time after which you want the

alarm to sound by pressing the + or – sen-

3. You will hear 2 beeps to confirm that the

time has been set. The clock will start

counting down from the selected time and

symbol will flash slowly.

4. When the time is up, the alarm will go off

and symbol will flash quickly.

5. Touch any sensor to stop the alarm.

Symbol will switch off.

If you want to change the timer alarm, simply

touch sensor with your fingertip and

then press the + or – sensor. You will hear 2

beeps to confirm that the time has been chan-

ged. The clock will start counting down from

the new time and symbol will flash

NOTE You cannot see the current time on the display

when the timer alarm is set.

Programming Cooking Time

1. Touch sensor with your fingertip until

the AUTO symbol starts to flash and 00:00

appears on the display.

2. Select the cooking time by pressing the +

3. You will hear 2 beeps, the AUTO symbol will

flash slowly and the display will show the

time left before the oven switches off auto-

4. Select a cooking function and temperature.

5. Once the cooking time is up, the oven will

turn off, an alarm will sound and the AUTO

symbol will flash quickly.

6. Touch any sensor to stop the alarm and to

turn off the AUTO symbol. The oven will

7. Set the controls to to turn off the oven.

You can change the remaining cooking time at

any time by touching sensor with your fin-

gertip until the AUTO symbol starts to flash

quickly. Now touch the + or – sensor to change

NOTE You cannot see the current time on the display

when the cooking time is set.

Electronic Clock Settings

3172465-002 EPIFA.QXD:- 20/10/11 08:02 Página 2021

ENGLISH Programming the Cooking Stop Time

1. Touch sensor with your fingertip until

the AUTO symbol starts to flash.

2. Select the cooking stop time by pressing

3. You will hear 2 beeps, the display will show

the current time and the AUTO symbol will

flash slowly to indicate that the oven will

switch off automatically.

4. Select a cooking function and temperature.

5. When the cooking time is up, the oven will

turn off, an alarm will sound and the AUTO

symbol will flash quickly.

6. Touch any sensor to stop the alarm and to

turn off the AUTO symbol. The oven will

7. Set the controls to to turn off the oven.

You can change the stop cooking time at any

time by touching sensor with your finger-

tip until the AUTO symbol starts to flash

quickly and you see the stop time on the dis-

play. Now touch the + or – sensor to change

Programming Cooking Time and Cooking

1. Touch sensor with your fingertip until

the AUTO symbol starts to flash and 00:00

appears on the display.

2. Select the cooking time by pressing the +

3. You will hear 2 beeps, the display will show

the remaining cooking time, and the AUTO

symbol will flash slowly.

4. Touch sensor until the AUTO symbol

starts to flash quickly. The display will

show the current time and the programmed

5. Select the cooking stop time by pressing

6. You will hear 2 beeps and the display will

show the current time.

7. Select a cooking function and temperature.

8. The oven will remain off and the AUTO light

will be on. The oven is now programmed.

9. When it is time to start cooking, the oven

will turn on and will operate for the pro-

grammed cooking time.

10.While cooking, the display will show the

cooking time remaining and the AUTO

symbol will flash slowly.

11.When the cooking time is up, the oven will

turn off, an alarm will sound, and the

AUTO symbol will flash quickly.

12.Touch any sensor to stop the alarm and to

turn off the AUTO symbol. The oven will

13.Set the controls to to turn off the oven.

If you want to change the remaining cooking

time while the oven is on, press sensor

until the AUTO symbol starts to flash quickly.

Now press the + or – sensor to change the

Child Safety Function

This function can be selected at any time

while using the oven.

To activate the function, press the + and –

sensors at the same time for several

seconds. You will hear a beep and the display

will show the word SAFE. The clock is locked.

If the oven is off and you activate the child

safety function, it will not work even if a coo-

king function is selected.

If this function is activated while you are coo-

king, it will only lock the electronic clock set-

If a clock sensor is touched while the child

safety function is on, the word SAFE will appear

on the display. The clock is locked.

3172465-002 EPIFA.QXD:- 20/10/11 08:02 Página 2122

To disable the function, press the + and – sen-

sors at the same time for several seconds

until you hear a beep.

In the event of a power failure, your electronic

clock settings will be erased and 12:00 will

flash on the clock display. Reset the clock and

With this function, any grease or dirt that is

stuck to the walls of the oven can easily be

removed through the combined action of

steam and the excellent properties of the new

Thanks to the new Teka

logy, the oven does not need to be cleaned

with a grease removal product. When the

water and dirt are removed, the walls of the

oven are clean and grease-free.

How to use the oven cleaning cycle

Always use the cleaning programme with a

cold oven. Running it with a hot oven may

have adverse effects.

1. First remove the trays and all accessories

from the oven interior, including the tray

supports and telescopic guide rails.

Do not clean the oven and tray at the same

you will not obtain good results. To clean the

tray, follow the instructions provided later on.

2. With the oven cold, pour 300 ml of water

into the bottom of the oven cavity.

3. Turn the control dial to position .

4. You will hear a beep indicating that the Teka

cycle has started. Symbol

will flash slowly and the time remain-

ing to complete the cycle will appear on the

IMPORTANT The duration of this cycle cannot be changed.

To stop the cycle before it is finished, turn the

control dial to position .

3172465-002 EPIFA.QXD:- 20/10/11 08:02 Página 2223

5. When the cycle is finished, the oven will

turn itself off, an alarm will sound and

symbol will flash quickly.

6. Touch any sensor with your fingertip to stop

the alarm and to turn off symbol .

7. Turn the control dial to position .

8. Any traces of dirt and excess water can now

be removed with a damp cloth.

IMPORTANT Do not open the oven door until the cleaning

programme has completely finished as the

cooling phase is necessary for it to work pro-

The cleaning programme should be done at a

low temperature. When it has finished, any

residue can be safely removed with a damp

cloth. Cooling times vary depending on the

room temperature. Before touching any inside

surface of the oven, check that it is cool.

How to use the tray-cleaning cycle

enamel’s excellent proper-

ties mean that any traces of cooked food can

easily be removed from the trays. If stubborn

traces of cooked food remain after normal

cleaning, do the following:

1. Place the tray that needs cleaning on the

middle shelf support.

2. With the oven cold, slowly pour 300 ml of

water into the tray.

IMPORTANT Teka Hydroclean enamel has been designed to

be cleaned using the oven’s automatic

cleaning programme and other cleaning

methods can damage it. Anti-limescale

products in particular can seriously damage

the enamel’s properties.

Teka Hydroclean enamelled oven trays should

not be cleaned in the dishwasher. If deep

cleaning is needed, use a gentle detergent.

Some foods such as tomato, vinegar or salt-

cooked roasts, can make the enamel’s

surface appear to change; this is normal.

3172465-002 EPIFA.QXD:- 20/10/11 08:02 Página 2324

Our contribution to enviromental protection: we use recycled paper.