F88082VI0P - Dishwasher AEG - Free user manual and instructions

USER MANUAL F88082VI0P AEG

www.aeg.com/productregistration

– Bed-and-breakfast-accommodatie.

apparaat in werking is

Koud water of warm water

11. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable

performance for many years, with innovative technologies that help make life simpler –

features you might not find on ordinary appliances. Please spend a few minutes reading to get

the very best from it.

Visit our website for:

Get usage advice, brochures, trouble shooter, service information:

Register your product for better service:

www.aeg.com/productregistration

Buy Accessories, Consumables and Original spare parts for your appliance:

CUSTOMER CARE AND SERVICE We recommend the use of original spare parts.

When contacting Service, ensure that you have the following data available.

The information can be found on the rating plate. Model, PNC, Serial Number.

Warning / Caution-Safety information

General information and tips

Environmental information

Subject to change without notice.

SAFETY INSTRUCTIONS Before the installation and use of the ap-

pliance, carefully read the supplied in-

structions. The manufacturer is not re-

sponsible if an incorrect installation and

use causes injuries and damages. Always

keep the instructions with the appliance

for future reference.

1.1 Children and vulnerable

Risk of suffocation, injury or per-

• Do not let persons, children included,

with reduced physical sensory, re-

duced mental functions or lack of ex-

perience and knowledge use the ap-

pliance. They must have supervision or

instruction for the operation of the ap-

pliance by a person who is responsible

• Do not let children play with the appli-

• Keep all packaging away from chil-

• Keep all detergents away from chil-

• Keep children and pets away from the

appliance door when it is open.

• Remove all the packaging.

• Do not install or use a damaged appli-

• Do not install or use the appliance

where the temperature is less than 0

• Obey the installation instruction sup-

plied with the appliance.

• Make sure that the appliance is instal-

led below and adjacent to safe struc-

Electrical connection

Risk of fire and electrical shock.

• The appliance must be earthed.

• Make sure that the electrical informa-

tion on the rating plate agrees with

the power supply. If not, contact an

• Always use a correctly installed shock-

• Do not use multi-plug adapters and

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the appliance power supply

cable need to be replaced, this must

be carried out by our Service Centre.

• Connect the mains plug to the mains

socket only at the end of the installa-

tion. Make sure that there is access to

the mains plug after the installation.

• Do not pull the mains cable to discon-

nect the appliance. Always pull the

• Do not touch the mains cable or the

mains plug with wet hands.

• This appliance complies with the

• Make sure not to cause damage to the

• Before you connect the appliance to

new pipes or pipes not used for a long

time, let the water flow until it is clean.

• The first time you use the appliance,

make sure that there is no leakage.

• The water inlet hose has a safety valve

and a sheath with an inner mains ca-

www.aeg.com• If the water inlet hose is damaged, im-

mediately disconnect the mains plug

from the mains socket. Contact the

Service to replace the water inlet hose.

• This appliance is intended to be used

in household and similar applications

– Staff kitchen areas in shops, offices

and other working environments

– By clients in hotels, motels and oth-

er residential type environments

– Bed and breakfast type environ-

Risk of injury, burns, electrical

• Do not change the specification of this

• Put knives and cutlery with sharp

points in the cutlery basket with the

points down or in a horizontal posi-

• Do not keep the appliance door open

without supervision to prevent to fall

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous.

Obey the safety instructions on the

detergent packaging.

• Do not drink and play with the water in

• Do not remove the dishes from the

appliance until the programme is

completed. There can be detergent

• The appliance can release hot steam if

you open the door while a programme

• Do not put flammable products or

items that are wet with flammable

products in, near or on the appliance.

• Do not use water spray and steam to

clean the appliance.

Risk of injury or suffocation.

• Disconnect the appliance from the

• Cut off the mains cable and discard it.

• Remove the door catch to prevent

children and pets to get closed in the

The Beam-on-Floor is a light that shows

on the floor below the appliance door.

• When the programme starts to oper-

ate, the red light comes on and stays

on for all the duration of the pro-

• When the programme is completed,

the green light comes on.

• When the appliance has a malfunc-

tion, the red light flashes.

The Beam-on-Floor goes off

when the appliance is deactiva-

Indicators Description

Salt indicator. It is always off while the programme operates.

Rinse aid indicator. It is always off while the programme oper-

4. PROGRAMMES Programme Degree of soil

ExtraHygiene ENGLISH 23Programme Degree of soil

7 Normal or light soil

The appliance senses the degree of soil and the quantity of items in the baskets. It

automatically adjusts the temperature and quantity of the water, the energy

consumption and the programme duration.

This programme has a high temperature rinsing phase for better hygiene results. During

the rinsing phase, the temperature stays at 70 °C for at least 10 minutes.

With this programme you can wash a load with fresh soil. It gives good washing results

With this programme you have the most efficient use of water and energy consumption

for crockery and cutlery with normal soil. (This is the standard programme for test

It is not possible to set ExtraHygiene if AutoOpen is active. Deactivate AutoOpen.

It is not possible to set TimeSaver if AutoOpen is active. Deactivate AutoOpen.

With this programme you can wash a load with mixed soil. Very heavy soil in the lower

basket and normal soil in the upper basket. The water pressure and the water

temperature in the lower basket are higher than in the upper basket.

Use this programme to quickly rinse the dishes. This prevents the remaining food to

bond on the dishes and bad odours to come out from the appliance.

Do not use detergent with this programme.

The pressure and the temperature of the water, the variations of the mains supply, the

options and the quantity of dishes can change the programme duration and the

Information for test institutes

For all the necessary information for test performance. send an email to:

info.test@dishwasher-production.com

Write down the product number (PNC) that is on the rating plate.

If one or more options are set,

make sure that the related indi-

cators are on before the pro-

With this option you have better hygiene

results. During the rinsing phase, the

temperature stays at 70 °C for at least 10

How to activate the ExtraHygiene

1. Press ExtraHygiene. The related in-

dicator comes on. In the display you

can see the update of the pro-

• If the option is not applicable to

the programme, the related indica-

tor flashes quickly 3 times and then

This option increases the pressure and

the temperature of the water. The wash-

ing and drying phases are shorter. The

total programme duration decreases by

The washing results are the same as with

the normal programme duration. The

drying results can decrease.

How to activate the TimeSaver option

1. Press TimeSaver. The related indica-

tor comes on. In the display you can

see the update of the programme

• If the option is not applicable to

the programme, the related indica-

tor flashes quickly 3 times and then

goes off. ENGLISH 255.3 Multitab

Activate this option only when you use

the combi detergent tablets.

This option deactivates the use of rinse

aid and salt. The related indicators stay

The programme duration can increase.

How to activate the Multitab option

1. Press the on/off button to activate

2. Press Multitab, the related indicator

If you stop to use the combi

detergent tablets, before you start to

use separately detergent, rinse aid

and dishwasher salt, do these steps:

1. Set the water softener to the highest

2. Make sure that the salt container and

the rinse aid dispenser are full.

3. Start the shortest programme with a

rinsing phase, without detergent and

4. Adjust the water softener to the wa-

ter hardness in your area.

5. Adjust the released quantity of rinse

This option gives good drying results

with less energy consumption.

This option is automatically activated

when you set the programme ECO 50°.

The AutoOpen indicator comes on.

It is not possible to set this option with

• While the drying phase operates, a

device opens the appliance door and

• At the end of the programme, the de-

vice and the appliance door retract.

The appliance automatically deacti-

Do not try to close the appliance

door while the device keeps the

door ajar. This can cause dam-

age to the appliance.

If you want to deactivate the AutoOpen

option, press AutoOpen. The related in-

In this condition, the energy consump-

tion of the programme increases.

5.5 Acoustic signals

The acoustic signals operate when the

appliance has a malfunction, when the

adjustment of the level of the water soft-

ener occurs and when the programme is

By default, the acoustic signals are on,

but it is possible to deactivate them.

How to deactivate the acoustic signals

1. Press the on/off button to activate

the appliance. Make sure that the ap-

pliance is in setting mode, refer to

“Setting and starting a programme”.

2. Press and hold, at the same time,

Program and ExtraHygiene until the

indicators of Delay, Program and Ex-

traHygiene start to flash.

3. Press ExtraHygiene.

• The indicators of Delay and Pro-

Acoustic signals on.

Acoustic signals off.

www.aeg.com4. Press ExtraHygiene to change the

5. Press the on/off button to deactivate

the appliance and to confirm the set-

1. Make sure that the set level of the

water softener agrees with the water

hardness in your area. If not, adjust

the water softener. Contact your local

water authority to know the water

hardness in your area.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Processing residues can stay in the

appliance. Start a programme to re-

move them. Do not use detergent

and do not load the baskets.

6.1 Adjusting the water softener

Do not use salt at this level.

You must adjust the water soft-

ener manually and electronically. ENGLISH 27Manual adjustment

Turn the water hardness dial to the posi-

Electronic adjustment

1. Press the on/off button to activate

the appliance. Make sure that the ap-

pliance is in setting mode, refer to

“Setting and starting a programme”.

2. Press and hold, at the same time,

Program and ExtraHygiene until the

indicators of Delay, Program and Ex-

traHygiene start to flash.

• The indicators of Program and Ex-

• The indicator of Delay continues to

• The acoustic signals operate, e.g.

five intermittent acoustic signals =

• The display shows the current set-

ting of the water softener, e.g.

4. Press Delay again and again to

5. Press the on/off button to deactivate

the appliance and to confirm the set-

6.2 Filling the salt container

Turn the cap counterclockwise and

open the salt container.

Put 1 litre of water in the salt con-

tainer (only for the first time).

Fill the salt container with dishwash-

Remove the salt around the opening

of the salt container.

Turn the cap clockwise to close the

Water and salt can come out

from the salt container when you

fill it. Risk of corrosion. To pre-

vent it, after you fill the salt con-

tainer, start a programme.

Press the release button (D) to open

more than the mark 'max'.

Remove the spilled rinse aid with an

absorbent cloth to prevent too much

Close the lid. Make sure that the re-

lease button locks into position.

You can turn the selector of the

released quantity (B) between

position 1 (lowest quantity) and

position 4 (highest quantity).

1. Open the water tap.

2. Press the on/off button to activate

the appliance. Make sure that the ap-

pliance is in setting mode, refer

to ’Setting and starting a pro-

3. Load the baskets.

4. Add the detergent.

• If you use the combi detergent

tablets, activate the Multitab op-

5. Set and start the correct programme

for the type of load and the degree

Press the release button (B) to open

Put the detergent in the compart-

If the programme has a prewash

phase, put a small quantity of deter-

gent on the inner part of the appli-

If you use detergent tablets, put the

tablet in the compartment (A).

Close the lid. Make sure that the re-

lease button locks into position.

ENGLISH 297.2 Setting and starting a

For some settings it is necessary that the

appliance is in setting mode.

Press the on/off button to activate the

appliance. The appliance is in setting

mode when the display shows 2 horizon-

tal status bars. If the control panel does

not show this condition, press and hold,

at the same time, Program and Extra-

Hygiene until the display shows 2 hori-

Starting a programme without

1. Open the water tap.

2. Press the on/off button to activate

the appliance. Make sure that the ap-

pliance is in setting mode.

3. Press Program again and again until

you see in the display the number of

the programme you want to set. The

programme number flashes. If you

want you can set the applicable op-

4. Close the appliance door, the pro-

gramme starts. The programme du-

ration starts to decrease with steps of

Starting a programme with

1. Set the programme.

2. Press Delay again and again until the

display shows the delay time you

want to set (from 1 to 24 hours).

• The delay time flashes in the dis-

• The Delay indicator comes on.

3. Close the appliance door. The count-

• When the countdown is comple-

ted, the programme starts.

Opening the door while the

If you open the door, the appliance

stops. When you close the door, the ap-

pliance continues from the point of inter-

Cancelling the delay start

while the countdown operates

When you cancel the delay start, also the

programme is cancelled.

1. Press and hold, at the same time,

Program and ExtraHygiene until the

display shows 2 horizontal status

2. Set the programme again.

Cancelling the programme

1. Press and hold, at the same time,

Program and ExtraHygiene until the

display shows 2 horizontal status

Make sure that there is detergent

in the detergent dispenser be-

fore you start a new programme.

At the end of the programme

The display shows 0:00 and the end indi-

1. Press the on/off button to deactivate

2. Close the water tap.

button, the AUTO OFF function

pliance a few minutes after the

end of the programme.

This helps to decrease the ener-

• Let the dishes become cold before

you remove them from the appliance.

Hot dishes can be easily damaged.

• First remove the items from the lower

basket, then from the upper basket.

• There can be water on the sides and

on the door of the appliance. Stainless

steel becomes cool more quickly than

www.aeg.com8. HINTS AND TIPS

8.1 The water softener

Hard water contains a high quantity of

minerals that can cause damage to the

appliance and bad washing results. The

water softener neutralises these miner-

The dishwasher salt keeps the water

softener clean and in good conditions. It

is important to set the right level of the

water softener. This makes sure that the

water softener uses the correct quantity

of dishwasher salt and water.

8.2 Using salt, rinse aid and

• Only use salt, rinse aid and detergent

for dishwasher. Other products can

cause damage to the appliance.

• The rinse aid helps, during the last

rinsing phase, to dry the dishes with-

out streaks and stains.

• Combi detergent tablets contain de-

tergent, rinse aid and other added

agents. Be sure that these tablets are

applicable to the water hardness in

your area. Refer to the instructions on

the packaging of the products.

• Detergent tablets do not fully dissolve

with short programmes. To prevent

detergent residues on the tableware,

we recommend that you use the tab-

lets with long programmes.

Do not use more than the correct

quantity of detergent. Refer to

the instructions on the detergent

8.3 Loading the baskets

Refer to the supplied leaflet with

examples of the load of the bas-

• Only use the appliance to wash items

that are dishwasher-safe.

• Do not put in the appliance items

made of wood, horn, aluminium, pew-

• Do not put in the appliance items that

can absorb water (sponges, household

• Remove remaining food from the

• To remove easily remaining burned

food, soak pots and pans in water be-

fore you put them in the appliance.

• Put hollow items (cups, glasses and

pans) with the opening down.

• Make sure that cutlery and dishes do

not bond together. Mix spoons with

• Make sure that glasses do not touch

• Put the small items in the cutlery bas-

• Put the light items in the upper bas-

ket. Make sure that they do not move.

• Make sure that the spray arms can

move freely before you start a pro-

8.4 Before starting a

• The filters are clean and correctly in-

• The spray arms are not clogged.

• The position of the items in the bas-

• The programme is applicable for the

type of load and for the degree of soil.

• The correct quantity of detergent is

• There is dishwasher salt and rinse aid

(unless you use combi detergent tab-

• The cap of the salt container is tight.

ENGLISH 319. CARE AND CLEANING WARNING!

Before maintenance, deactivate

the appliance and disconnect the

mains plug from the mains sock-

Dirty filters and clogged spray

arms decrease the washing re-

Make a check regularly and, if

necessary, clean them.

9.1 Cleaning the filters

Turn the filter (A) counterclockwise

To disassemble the filter (A), pull

apart (A1) and (A2).

Remove the filter (B).

Wash the filters with water.

Before you put the filter (B) back,

make sure that there are no residues

of food or soil in or around the edge

Make sure that the filter (B) is cor-

rectly positioned under the 2 guides

Assemble the filter (A) and put it

back in filter (B). Turn it clockwise

An incorrect position of the filters

can cause bad washing results

and damage to the appliance.

9.2 Cleaning the spray arms

Do not remove the spray arms.

If the holes in the spray arms are clog-

ged, remove remaining parts of soil with

a thin pointed object.

9.3 External cleaning

Clean the appliance with a moist soft

Only use neutral detergents. Do not use

abrasive products, abrasive cleaning

www.aeg.com10. TROUBLESHOOTING The appliance does not start or it stops

Before you contact the Service, refer to

the information that follows for a solu-

tion to the problem.

With some problems, the display

shows an alarm code:

- The appliance does not fill with

- The appliance does not drain

- The anti-flood device is on.

Deactivate the appliance before

Problem Possible solution

You cannot activate the appli-

Make sure that the mains plug is connected

to the mains socket.

Make sure that there is not a damaged fuse

The programme does not start. Make sure that the appliance door is closed.

If the delay start is set, cancel the setting or

wait for the end of the countdown.

The appliance does not fill with

Make sure that the water tap is open.

Make sure that the pressure of the water

supply is not too low. For this information,

contact your local water authority.

Make sure that the water tap is not clogged.

Make sure that the filter in the inlet hose is

Make sure that the inlet hose has no kinks or

The appliance does not drain

Make sure that the sink spigot is not clog-

Make sure that the drain hose has no kinks

The anti-flood device is on. Close the water tap and contact the Service.

After the checks are completed, activate

the appliance. The programme contin-

ues from the point of interruption.

If the problem occurs again, contact the

If the display shows other alarm codes,

contact the Service.

10.1 If the washing and drying

results are not satisfactory

Whitish streaks or bluish layers on

• The released quantity of rinse aid is

too much. Adjust the rinse aid selector

to a lower position.

• The quantity of detergent is too much.

ENGLISH 33Stains and dry water drops on glasses

• The released quantity of rinse aid is

not sufficient. Adjust the rinse aid se-

lector to a higher position.

• The quality of the detergent can be

• The programme is without a drying

phase or with a low temperature dry-

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the

• The quality of the combi detergent

tablets can be the cause. Try a differ-

ent brand or activate the rinse aid dis-

penser and use rinse aid together with

the combi detergent tablets.

Refer to ‘HINTS AND TIPS’ for

other possible causes.

10.2 How to activate the rinse

The activation of the rinse aid dispenser

can occur only with the Multitab option

1. Press the on/off button to activate

the appliance. Make sure that the ap-

pliance is in setting mode, refer to

“Setting and starting a programme”.

2. Press and hold, at the same time,

Program and ExtraHygiene until the

indicators of Delay, Program and Ex-

traHygiene start to flash.

• The indicators of Delay and Extra-

• The indicator of Program continues

• The display shows the current set-

Rinse aid dispenser off.

Rinse aid dispenser on.

4. Press Program to change the setting.

5. Press the on/off button to deactivate

the appliance and to confirm the set-

6. Adjust the released quantity of rinse

Electrical connection Refer to the rating plate.

Cold water or hot water

Connect the water inlet hose to a water tap with a 3/4'' thread.

If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian

energy), use the hot water supply to decrease energy consumption.

www.aeg.com12. ENVIRONMENT CONCERNS Recycle the materials with the

. Put the packaging in

applicable containers to recycle it.

Help protect the environment and

human health and to recycle waste

of electrical and electronic

appliances. Do not dispose

appliances marked with the symbol

with the household waste. Return the

product to your local recycling

facility or contact your municipal

www.aeg.com/productregistration

www.aeg.com/productregistration