NC - Speaker ELIPSON - Free user manual and instructions

Product Type	In-ceiling speaker, 2-way coaxial
Models	INF6 (16 cm) / INF8 (20 cm)
Nominal Power	100 W (INF6) / 130 W (INF8)
Frequency Response	60 Hz - 30 kHz (INF6) / 45 Hz - 30 kHz (INF8)
Sensitivity	88 dB (INF6) / 89 dB (INF8) @ 1W/1m
Impedance	8 Ω
Crossover Frequency	3200 Hz (INF6) / 2500 Hz (INF8)
Midbass Driver	160 mm carbon fiber + PMI foam (INF6) / 200 mm (INF8)
Tweeter	19 mm titanium dome, 30° adjustable (INF6) / 25 mm (INF8)
Dimensions (diameter x depth)	Ø237 x 100 mm (INF6) / Ø272 x 114 mm (INF8)
Cutout Dimensions	Ø212 mm (INF6) / Ø246 mm (INF8)
Weight	1,75 kg (INF6) / 2,42 kg (INF8)
Color	White, ready to paint
Grille	Metallic, magnetic, removable and paintable
Mounting	Screw-tightening mounting tabs (4 points)
Tweeter Orientation	30° in all directions
Warranty	2 years (excluding transport and installation)
Maintenance and Cleaning	Soft dry cloth; grille washable with soapy water (when detached)
Safety	Avoid clipping (crackling) by lowering the volume; do not overload the amplifier; do not paint the grille when mounted
Spare Parts and Repairability	Contact an authorized Elipson dealer; no parts included in the box

Frequently Asked Questions - NC ELIPSON

What is the recommended amplifier power for these speakers?

The speakers can handle 100 W (INF6) or 130 W (INF8). It is recommended to use an amplifier with power equal to or less than these values to avoid damage. Note that half volume can already deliver full power.

How to install the in-ceiling speaker?

Use the included cutout template to mark the hole. Cut the ceiling at 90° after checking for obstacles. Connect the cables respecting polarity (+/-). Insert the speaker and tighten the screws to engage the mounting tabs.

Can I paint the speaker grille?

Yes, grilles can be painted. Remove the rear fabric and clean the grille with a mild solvent. Use a diluted spray paint (5 parts thinner to 1 part paint). Never paint the grille while mounted on the speaker.

How to orient the tweeter?

The adjustable tweeter can be tilted up to 30° in all directions. Gently press the plastic cradle to direct it toward the listening area to optimize high-frequency reproduction.

What to do in case of crackling or distortion?

These symptoms indicate amplifier clipping. Immediately lower the volume to avoid damaging the speakers. Prolonged clipping can destroy tweeters and woofers.

What is the difference between INF6 and INF8 models?

The INF8 is larger and more powerful (130 W vs 100 W) with a 200 mm midbass driver, a 25 mm tweeter, 89 dB sensitivity, and frequency response down to 45 Hz. The INF6 offers 88 dB and goes down to 60 Hz.

How to clean the speakers?

Clean the frame and grille with a soft dry cloth. For deeper cleaning, remove the grille and wash it with soapy water, then dry thoroughly before replacing.

Does the warranty cover installation?

No, the 2-year warranty only covers repair of the speaker in case of defect. Transport, installation, and labor costs are not included. Keep the purchase receipt as proof.

Can I install the speaker in a bathroom?

The manual does not specify use in humid environments. For a bathroom, choose speakers specifically designed to resist moisture. Contact your dealer for more information.

How to connect the speaker to the amplifier?

Use stripped cables and connect them to the screw terminals respecting polarity: red wire (+) to red terminal, black wire (-) to black terminal. Reversed polarity degrades stereo imaging and bass.

USER MANUAL NC ELIPSON

Thank you for choosing Epilson products.

Take time to read this manual carefully before installing the loudspeakers :

it contains all the safety and operating instructions that should be followed to

optimize the performances of your Elipson speakers. We highly recommend you

to keep both packaging and owner's manual for future use.

I. UNPACKING

Elipson keeps to a strict quality control regimen and all factory-sealed products leave our facility in perfect condition. If there are any damages visible or concealed they have occurred in handling and must be reported immediately to your Elipson authorized dealer.

Carefully remove the speaker from the box, take caution as the size often deceives the actual weight. Save all custom cartons and packaging foams for future use. They are rather expensive and may come in handy for future upgrades.

Pack contents :

1 acoustic speaker
- 1 metal grill
- 1 cut-out template

WARNING / IMPORTANT TECHNICAL NOTE

Please read before operating speakers. The warranty on speakers is void if the voice coils are burned or damaged as a result of overpowering or clipping.

OVERPOWERING : The volume control of most amplifiers and receivers is a logarithmic type, which means that full rated power may be reached with the volume control as little as the halfway point. In addition, operating the loudness feature or boosting the treble or bass controls increases power output well beyond rated levels. AS A RESULT OF THE ABOVE FACTORS, A 30-WATT AMPLIFIER CAN PRODUCE DISTORTED OUTPUT LEVELS OF OVER 100 WATT AND MAY DAMAGE YOUR LOUDSPEAKERS.

CLIPPING : Clipping refers to the power level at which an amplifier begins to distort a waveform by flattening its top and bottom into a square wave-shape. When fed to tweeters and/or midrange speakers, this may result in exceeding their maximum power handling capacity, causing damage to the speaker voice coil. CLIPPING CAN BE IDENTIFIED BY FUZZ OR DISTORTED SOUND. IF THIS IS HEARD, LOWER THE VOLUME IMMEDIATELY TO AVOID DAMAGE TO YOUR SYSTEM. CONTINUOUS CLIPPING WILL DAMAGE OR BURN OUT THE SPEAKERS.

The In-ceiling Infinite loudspeakers have been designed to reproduce all types of music as accurately as possible, provided that a few rules should be followed to optimise performance and achieve a realistic sound image. Before installing your speakers, you should consider the placement carefully, taking into account the location of electrical, plumbing and other fixtures. Contact your dealer for assistance if you are not sure of the best location in your particular room environment.

II. PLACEMENT

In-ceiling placement

Ideally, the speakers should be placed symmetrically above the listening position, spaced from about 1m to 3m. If possible, left and right speakers should be positioned at the same distance from the listening position.

IV. INSTALLATION

Preparation of mounting surfaces / Finishing of ceilings

Prior to start the installation of the speakers, it will be necessary to run cables to the speaker locations. See your dealer for more information on cable installation. After the cable has been properly installed, you are ready to mount the speakers.

1. Determine the best area to mount your speakers

This area of the ceiling or wall should be free of obstructions such as electrical conduit, HVAC ducts, or water lines. If possible, you should access to an attic or crawl space in order to best noting the location of such obstacles.

2. Find the eventual beams / joists near the desired speaker mounting location

We highly recommend you to use a good stud-finder tool for this procedure. If you are placing the speakers really close to some studs or other object, make sure you consider the size of the baffles flange, which extends beyond the mounting hole.

3. Make the hole

A punch out template for setting the hole is provided in the box. Position the template in the desired position and pencil an outline on the wall or ceiling.

4. Cutting the hole

Caution : this is the most important part of the entire installation. If you are uncertain about obstructions in the mounting area, you should start by cutting a small hole within the penciled area with a drywall saw. Cutting at a 45 degree angle will make drywall repair much easier if you need to repair the hole because of unexpected obstructions. Once you have determined there are no obstructions in your desired mounting location, start cutting the finished hole at a 90 degree angle to the wall surface.

5. Add insulation

If the area in the ceiling or wall is not already insulated, add an adequate amount of insulation material to fill the cavity. If the insulation material used is cover with foil or paper, position the foil or paper away from the speaker.

The mounting-feet sytem integrated into your speaker makes its installation very quick and easy to do, following only few steps.

1. Remove the grill and set aside in a clean dust-free environment.

2. Binding post terminals provide reliable contact for bare wire. Fix the cable of the speaker respecting the polarity of your amplifier (+ with + and - with -). Make sure the left channel of the amplifier is connected to the left channel of the speaker, and that the right channel of the amplifier is connected to the right channel of the speaker. A polarity inversion will result in a fuzzy stereo image and a low level of bass.

1. Make sure the mounting feet are turned inward to clear the opening and insert the speaker into the ceiling. Position the speaker into the hole.

Note : The flange of the speaker is designed to flex and conform to any small imperfections in the wall surface. Tighten the 4 screws on the front of the baffle only enough to make the flange become snug against the ceiling or wall. As you tighten the screws, the feet will automatically flip into an outward position, thereby clamping the drywall between the feet and the flange.

Caution: Over-tightening may warp the baffle, crack the ceiling, cause the flange to distort, and make the grill difficult to install.

4. Tweeter adjustment

The steerable tweeter can be directed to the listening area for superior treble and stereo image accuracy.

5. Secure the grill into place.

Note : The speaker flange incorporates high strength magnets to secure the grill into place. Simply line the grill with the speaker flange.

V. PAINTING INSTRUCTIONS

The grills can be painted. However, great care should be taken not to clog the holes, as this will severely reduce the sound quality of the speakers.

If you plan to paint your grills, it should be done before the installation. The scrub cloth backing must be removed prior to painting the grills. The surface should be cleaned with a light solvent to remove any dust or residue. Elipson recommends a light spray-painting using 5 parts thinning agent to 1 part paint. Do not paint the grill while they are attached to the speaker.

SPECIFICATIONS

INF6

INF8

Type	In-ceiling loudspeaker	In-ceiling loudspeaker
Power	100 W	130 W
Drive units	2 way coaxial Mid-bass: 6" carbon fiber with polymethylacrylamide foam (PMI) Tweeter: 3/4" titanium dome orientation 30° in all directions	2 way coaxial Mid-bass: 8" carbon fiber with polymethylacrylamide foam (PMI) Tweeter: 1" titanium dome orientation 30° in all directions
Frequency response (±3dB)	60 Hz - 30 kHz	45 Hz - 30 kHz
Sensitivity	88 dB/ 1W/ 1m	89 dB/ 1W/ 1m
Impedance	8 Ohms	8 Ohms
Crossover frequency	3200 Hz	2500 Hz
Dimensions	Ø237 mm x D100 mm	Ø272 mm x D 114 mm
Cut-out dimensions	Ø212 mm	Ø246 mm
Weight	1,75 kg	2,42 kg
Colour	White (ready for painting)

WARNING

Packaging

The packaging (box and packing) was designed for effective protection of your ELIPSON speaker during transportation and shipping. Please save them for later use. Protect the environment : if you wish to dispose of the packaging, please do so in the most environmentally responsible manner possible according to available measures (for example, sorted recycling).

At the end of its life, this device should not be disposed of the same way as household refuse. It should be returned to a center for the recycling of electronic equipment. This symbol on the product indicates that it has been designed so that it can be recycled according to specific procedures. You will therefore be making a significant contribution to the protection of the environment. This device respects the RoHS European directive. This means that it does not emit polluting substances when it is recycled (such as lead, mercury, cadmium, hexavalent chromium, polybromobiphenyles, polybromdiphenylethers).

WARRANTY

Elipson products have been designed and manufactured to the highest quality standards. If something goes wrong with your product, Elipson or its authorized distributor / dealer will handle the service and repair under these limited warranty terms. This limited warranty is valid for a 2-year period from original purchase date from an authorized Elipson dealer.

Terms of limited warranty

The warranty is limited to equipment repair. Neither transportation, nor any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty. The warranty is only valid for the original purchaser and is not transferable. The warranty will not apply in cases other than defects in materials and / or workmanship at the date of purchase and will not be applicable in the following cases :

• Damages caused by wrong or incorrect installation or connection.

• Damages caused by incorrect use, other use than the one described in the owner's manual, negligence, unauthorized modification or use of parts or of accessories that are not authorized by Elipson.

• Damages caused by unauthorized, unsuitable or faulty ancillary equipment.

• Damages caused by accidents, lightning, water, fire, heat or any other disturbance that would not be under Epilson control or responsibility.

• For products, which serial number has been altered, deleted, removed or made illegible.

• In case of repair and service executed by an unauthorized service person.

This warranty complements any national/federal/regional law obligations of local distributors/dealers and does not affect your statutory rights as a customer.

To claim repair under warranty

To claim repair or service under warranty you simply have to contact your local Epilson dealer, from whom your equipment has been purchased. To ensure that you will be able to ship your damaged product in correct manner, always retain the original packaging of your Epilson equipment. If you cannot contact your original dealer, or if you are using your Epilson product outside the purchase country, you should contact Epilson national distributor in the residence country, who will advise where the equipment can be serviced.

You can also visit our web site to check our contact information:

www.elipson.com

To validate your warranty, you need to produce, as a proof of purchase, your original purchase invoice specifying the date of purchase and stamped by your dealer.

INF 6

INF 8

elipson