A3iN - Universal remote TEMIUM - Free user manual and instructions

Product type	Universal remote control
Brand	TEMiuM
Model	A3iN
Power supply	3 AAA 1.5 V batteries (alkaline recommended)
Approximate dimensions	18 x 5 x 2 cm
Approximate weight (with batteries)	100 g
Range	Infrared, up to 8 meters
Compatible device types	TV, VCR, SAT, DVD and other audio-video devices
Configuration methods	By direct code entry or by automatic search in the library
Special functions	Channel navigation, permanent volume, macro power (simultaneous on/off of two devices)
Secondary functions	Accessible via SHIFT key
Low battery indicator	Indicator blinks slowly 2 times after a command
Care and cleaning	Dust with a soft dry cloth. Do not use corrosive or abrasive products.
Safety	Do not expose to water, humidity, shocks or high temperatures. Do not disassemble.
Used batteries	Do not dispose of with household waste. Recycle at a collection point.
Repairability	No user-serviceable parts. Contact customer service.
France hotline	DARTY: 0 978 970 970 (local call rate), 7 days a week from 7am to 10pm
Belgium hotline	VANDENBORRE: 02 334 00 00 (Monday to Saturday)

Frequently Asked Questions - A3iN TEMIUM

My remote control does not work at all, what should I do?

First check that the audio-visual device is on and its main switch is activated. Make sure the batteries are inserted correctly respecting the +/- polarities. If the indicator blinks slowly twice, the batteries are low, replace them all.

How do I program my remote control for my television?

Refer to the code list provided in the manual. Turn on your TV, press the 'TV' key, then simultaneously press 'CH+' and 'VOL-' for 2 seconds until the indicator lights up. Enter the 4-digit code corresponding to your brand. If the TV responds, it's done. Otherwise, try other codes.

I cannot find the code for my device in the list, what should I do?

Use the automatic search method. Turn on your device, press the corresponding mode key, then simultaneously press 'CH+' and 'VOL-' for 2 seconds. Enter the magic code (e.g., 0001 for TV). Then, point the remote at the device and slowly and repeatedly press the '⏻' key until the device turns off. As soon as it turns off, immediately press 'CH+' and 'VOL-' to confirm the code.

How can I control the volume of my television while using another mode?

Activate the 'Volume among channels' function: in TV mode, hold down the 'VOL+' key, then press the other mode key (e.g., SAT) and release 'VOL+'. The indicator lights up once to confirm. To deactivate, do the same with 'VOL-'.

Can I turn on or off two devices at the same time with the remote control?

Yes, thanks to the Macro Power function. In TV mode, hold down the '⏻' key, then press the other mode key (e.g., SAT) and release '⏻'. The indicator lights up once to confirm. Thus, the '⏻' key will control both devices simultaneously.

How do I access secondary functions (different color symbols)?

First press the 'SHIFT' key, then press the corresponding function key. The indicator lights up briefly. Refer to the secondary functions table in the manual for assignments.

What if some keys on the remote control do not work properly?

This probably means that the code you entered is not perfectly adapted. Try other codes from the list for the same brand until most keys work properly.

How do I replace the batteries?

Remove the battery compartment cover on the back of the remote. Insert 3 AAA 1.5 V batteries respecting the polarities (+/- signs). Preferably use alkaline batteries. Replace the cover. If not used for a long time, remove the batteries to prevent leakage.

How do I clean my remote control?

Dust it with a soft dry cloth. Never use corrosive, abrasive or solvent products. Avoid any contact with water or humidity.

Where should I dispose of my used remote control and batteries?

Do not throw the remote control or batteries with household waste. Take them to an appropriate collection or recycling point in accordance with local regulations. Used batteries must be recycled.

USER MANUAL A3iN TEMIUM

UNIVERSAL REMOTE CONTROL 3 in 1

Temium

User Manual

Kesa Electricals© UK: EC1N 6TE 18/04/2012

Congratulations! Your Universal Remote Control (URC) is a state-of-the-art device which integrates many different infra-red remote controls to deliver instant A/V action to your fingertips.

Before operating the remote, please read thoroughly (1) the inside of the coversheet and (2) this manual. Then reserve them for future reference.

1 HOW TO INSTALL THE BATTERIES

Alkaline batteries are recommended. The number of batteries required is stated on the back of the coversheet.

1. Remove the battery cover on the back of your URC.
2. Check the polarity of the batteries and the “+/-” marks inside the battery compartment.
3. Insert the batteries.
4. Push the battery cover back in place.

Battery Low

If the indicator flashes twice slowly after using the URC, it shows that the battery level is low. You must replace them with new batteries to ensure proper functioning.

2 HOW TO SET UP THE URC

By entering Device Code

You may setup the URC by following the code entering instructions.

1. Referring to the DEVICE CODE LIST, look up the 4-digit Device Code which corresponds to the brand of your A/V equipment. If there is more than one Device Code listed under your brand, start from the first code.
2. Press the desired Device Mode Key (e.g. TV).
3. Hold down "CH+" and "VOL-" on the URC simultaneously for 2 seconds until the indicator lights up.
4. Use the number keys ①-⑨ to enter your 4-digit Device Code. The indicator should go out immediately.

Turn on your device (e.g. TV), then try the function keys on the URC. If your device (e.g. TV) responds to your activated function correctly, you have entered the right Device Code. Otherwise, repeat the above steps with the next available Device Codes until your device (e.g. TV) responds to your activated function, and most keys work correctly.

* Simply repeat the above procedures to enter the Device Codes for your SAT, or DVD. (Remember to press the correct Device Mode Key in step 2 above)

Note :

• DVD and other Device Codes can be entered into any device modes except "TV" & "SAT" modes. Simply press the device mode key and enter your 4-digit device code for DVD and other devices.
  If the indicator flashes twice in step 4, a wrong Device Code has been entered. You are required to repeat step 2 to 4 again.

Suggestion :

• If you cannot find a correct Device Code for your equipment, see 2 HOW TO SET UP THE URC- By Searching Through the Library.
• For future reference you are recommended to take a note of your Device Codes in the space provided on the product's back label after setting up the URC correctly.

By Searching Through the Library

If you cannot identify a correct Device Code for your equipment from the Device Code list, you may search for the code in the library:-

1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g. (TV)).
3. Hold down "CH+" and "VOL-" on the URC simultaneously for 2 seconds until the indicator lights up.
4. Enter a corresponding Magic Search Code from the following table. The indicator should go out immediately.

DEVICE TYPE:	TV	VCR	SAT	DVD
MAGIC SEARCH CODE:	0001	0002	0003	0005

(e.g. press TV device mode key, then press “CH+” and “VOL-”, and enter TV Magic Search Code 0001.)

1. Press the same desired device mode key again as in step 2 above. (e.g. (TV))
2. Hold down "CH+" & "VOL-" simultaneously for 2 seconds until the indicator lights up, and your URC is ready to start searching.
3. Aim the URC at your device (e.g. TV), press the “ ⏻ ” key slowly and repeatedly until the device has been turned off.

Once your device has been turned off, immediately press Device Mode Key (e.g. TV) to lock in code and the indicator should go out.

* Simply repeat the above setup procedures to search for the Device Code for your SAT or DVD. (Remember to press the correct Device Mode Key and correct Magic Search Code in step 2-5 above)

IMPORTANT:

• If the power on/off function of your device is not infra-red controlled, you need to follow steps 2 to 6 above and start searching :-
• Press “(1)” and another function key alternately until your device responds to the expected function, then press “CH+” and “VOL-” to lock in the code.
  e.g. Press “ ⏻ ” & “ 1 ” alternately, or ;
  Press “ ⏻ ” & “ ▶ ” alternately.

Note:

• DVD and other device codes can be searched for and locked into any device modes except "TV" & "SAT" modes. Simply press the corresponding device mode key in step 2 & 5 and enter an appropriate Magic Search Code for your DVD and other devices.
• Each time you press the “ ⏻ ”, the URC will skip to the next code and send out a POWER signal trying to turn off your device.
  If you fail to stop pressing “ ⏻ ” in time when your device has been turned off, turn your device on again immediately. Before the indicator goes out, press “ ☑ ” on the URC to skip backward. Repeat step 7 above and lock in the code.
• If the indicator flashes twice after your pressing of “☐” key, you are already at the last code of the library. Press “CH+” and “VOL-” to resume the URC and repeat the above procedures carefully to search again.

3 OPERATING THE URC

Normal Operation

Once you have set up the URC for your A/V equipment, it works like your original remote control. To operate, just aim it at your equipment, press an appropriate device mode key and invoke the desired function by pressing a corresponding key on the URC. The indicator flashes during signal transmission and as confirmation of key touch.

Punch Through

Punch Through Channel

Punch through channel allows you to operate channel up and down without having to switch the device modes repeatedly even when your URC is in other operating modes.

To activate the punch through channel setting:

1. Press desired Device Mode Key (e.g. TV).
   2 Press and Hold "CH+" key.
2. Press desired Device Mode Key (e.g. SAT).
3. Release "CH+" (the indicator flashes once if the setting is activated).

To deactivate the punch through channel setting:

1. Press desired Device Mode Key (e.g. (TV)).
2. Press and Hold "CH-" key.
3. Press desired device Mode Key (e.g. (SAT)).
4. Release "CH-" (the indicator flashes twice if the setting is deactivated).

Punch Through Volume

Punch through volume allows you to operate volume up and down without having to switch the device modes repeatedly even when your URC is in other operating modes.

To activate the punch through volume setting:

1. Press desired Device Mode Key (e.g. TV).
   2 Press and Hold "VOL+" key.
2. Press desired Device Mode Key (e.g. (SAT)).
3. Release "VOL+" (the indicator flashes once if the setting is activated).

To deactivate the punch through volume setting:

1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "VOL-" key.
3. Press desired Device Mode Key (e.g. SAT).
4. Release "VOL-" (the indicator flashes twice if the setting is deactivated).

Macro Power

Macro Power allows you to turn two of your A/V equipment on/off simultaneously.

To activate the macro power setting:

1. Press desired Device Mode Key (e.g. TV).
   2 Press and Hold " ⏻ " key.
2. Press desired Device Mode Key (e.g. (SAT)).
3. Release " ⏻" (the indicator flashes once if the setting is activated).

To deactivate the macro power setting:

1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold “ ⏻ ” key.
3. Press desired Device Mode Key (e.g. (SAT)).
4. Release “ ⏻ ” (the indicator flashes twice if the setting is deactivated).

Symbols of the secondary functions are printed in different colours on the panel, and a SECONDARY FUNCTION TABLE is included on the inside page of the coversheet. To invoke a secondary function, press (SHIFT) followed by a corresponding function key.

5 MAINTENANCE

1. Do not expose your URC to dust, strong sunlight, humidity, high temperatures or mechanical shocks.
2. Do not use old and new batteries together as old batteries tend to leak.
3. Do not use corrosive or abrasive cleansers on your URC.
4. Keep the unit dust free by wiping it with a soft, dry cloth.
5. Do not disassemble your URC, it contains no user-serviceable parts.

6 TROUBLESHOOTING

Q. My URC does not work at all!
A. Check your A/V device, if the device's main switch is turned off, your URC cannot operate your device.
A. Check whether your batteries are inserted properly and are in the correct +/- position.
A. Check whether you have pressed the corresponding device mode key for your device.
A. If the batteries are low, replace the batteries.
Q. If several Device Codes are listed under the brand of my A/V device, how can I select the correct Device Code?
A. To seek the correct Device Code for your A/V device, test the codes one by one until most keys work properly.
Q. My A/V equipment responds only to some of the commands.
A. You have set a code for which only some commands work properly but some do not. Try other codes until most keys work properly.

IMPORTANT SAFETY WARNINGS

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNINGS:

This appliance is intended for domestic household use only and should not be used for any other purpose or in any other application, such as for none domestic use or in a commercial environment.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shell be placed on the apparatus.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

Battery Disposal

Do not dispose of batteries with household waste, they must be taken to your local recycling point for disposal at end of life.

The battery in this product is 3 x AAA 1.5V Cells.

These batteries are located in the remote control battery compartment and are readily accessible.

Batteries

We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product improvement and development.

Kesa Electricals© UK: EC1N 6TE 18/04/2012

Simple line drawing of a trash bin with two crossed lines indicating no waste or restriction (no text or symbols)

IMPORTANTES INSTRUCTIONS DE MISE AU REBUT

Simple line drawing of a trash bin with two crossed lines indicating no waste or restriction (no text or symbols)

IMPORTANT DISPOSAL INSTRUCTIONS

As a responsible retailer we care about the environment.

As such we urge you to follow the correct disposal procedure for your product and packaging materials. This will help conserve natural recourses and ensure that it is recycled in a manner that protects health and the environment.

You must dispose of this product and its packaging according to local laws and regulations.

Because this product contains electronic components, the product and its accessories must be disposed of separately from household waste when the product reaches its end of life.

Contact your local authority to learn about disposal and recycling.

The product and packaging should be taken to your local collection point for recycling. Some collection points accept products free of charge.

We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product improvement and development.