DVD-1080PK - DVD player SAMSUNG - Free user manual and instructions

USER MANUAL DVD-1080PK SAMSUNG

- Refer to the identification label located on the rear of your player for its proper operating voltage. - Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components for air circulation. - Do not push the disc tray in by hand. - Do not stack components. - Be sure to turn all components off before moving the player. - Before connecting other components to this player, be sure to turn them off. - Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time. - The mains plug is used as a disconnect device and shall stay readily operable at any time.

- This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. - Do not open covers and do not repair yourself. Refer servicing to qualified personal.

- Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only. - Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. - Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally. - When condensation forms inside the player due to sharp changes in temperature, the

player may not operate correctly. If this occurs, leave the player at room temperature until the inside of the player becomes dry and operational.

- Do not clean disc using record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface. - Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center. - Wipe the dirt away gently; never wipe a cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains chemicals that are harmful to the environ ment. - So, dispose of batteries in the proper man ner, according to federal, state, and local regulations. The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3. CAUTION: USE OF ANY CONTROLS,

ADJUSTMENTS, OR PROCEDURES OTHER

THAN SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE. Accessories Remote Control User’s Manual Batteries for Remote Control (AAA Size) Video/Audio Cable Install Batteries in the Remote control

1. Open the battery cover on the back of the remote

2. Insert two AAA batteries.

Make sure that the polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

• If remote control doesn’t operate properly: - Check the polarity + - of the batteries (Dry-Cell) - Check if the batteries are drained. - Check if remote control sensor is blocked by obstacles. - Check if there is any fluorescent lighting nearby. TABLE OF CONTENTS Precautions p. 2
• Before you start p. 3
• Setup General Features p. 4
• Disc Type and Characteristics p. 5
• Description p. 6
• Tour of the Remote Control p. 8
• Connections Choosing a Connection p. 9
• Basic Functions Playing a Disc p. 14
• Using the Search and Skip Functions p. 15
• Using the Display Function p. 15
• Using the Disc and Title Menu p. 16
• Using the Function Menu p. 16
• Repeat Play p. 16
• Slow Play p. 17
• Advanced Functions Adjusting the Aspect Ratio (EZ View) p. 17
• Selecting the Audio Language p. 18
• Selecting the Subtitle Language p. 18
• Changing the Camera Angle p. 19
• Using the Instant Replay/Skip Function p. 19
• Using the Bookmark Function p. 19
• Using the Zoom Function p. 20
• Clips Menu for MP3/WMA/JPEG/MPEG4/ CD Audio p. 20
• Folder Selection p. 20
• MP3/WMA/CD Audio Playback p. 21
• MPEG4 Playback p. 21
• Playing Media Files using the USB HOST feature p. 23
• CD Ripping p. 24
• Picture CD Playback p. 24
• Karaoke Functions Karaoke Functions p. 25
• Changing Setup Menu Using the Setup Menu p. 26
• Setting Up the Language Features p. 26
• Setting Up the Audio Options p. 27
• Setting Up the Display Options p. 29
• Setting Up the Parental Control p. 31
• Setting Up the Anynet+(HDMI-CEC) p. 32
• Reference Firmware Upgrade p. 33
• Troubleshooting p. 34
• USB Host Feature Supported Products p. 35
• Specifications p. 36

English BEFORE YOU STAR T SETUP General Features Excellent Sound Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction. Screen Both regular and widescreen(16:9) pictures can be viewed. Slow Motion An important scene can be viewed in slow motion. 1080p Playback This player upconverts regular DVDs for playback on 1080p TVs. Parental Control (DVD) The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc. Various On-Screen Menu Functions You can select various languages (Audio/Subtitle) and screen angles while enjoying movies. CD Ripping This feature lets you to copy audio files from disc to USB device into MP3 format. (Only Audio CD (CD DA)) Note - Discs which cannot be played with this player.

• CDGs play audio only, not graphics. - Ability to play back may depend on recording conditions.
• DVD+RW, -RW (V mode) - The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions. COPY PROTECTION Repeat You can repeat a song or movie simply by pressing the REPEAT button. Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copyprotected DVD discs. This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. MP3/WMA This unit can play discs created from MP3/WMA files.

PROGRESSIVE SCAN OUTPUTS

(525p,720p,1080p) Progressive Scan Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture. EZ VIEW (DVD) Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3). Digital Photo Viewer (JPEG) You can view Digital Photos on your TV. Instant Replay (DVD) This function is used to replay the previous 10 seconds of a movie from the current position. Instant Skip (DVD) This function skips playback ahead 10 seconds MPEG4 This unit can play MPEG4 formats within an avi file. HDMI (High Definition Multimedia Interface) HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV.

COMPATIBLE WITH THIS PRODUCT AND MAY

RECOMMENDED THAT THE USER SWITCH THE

OUTPUT. IF THERE ARE QUESTIONS

REGARDING YOUR TV SET COMPATIBILITY

WITH THIS MODEL 525p, 720p, 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.” Disc Type and Characteristics This DVD player is capable of playing the following types of discs with the corresponding logos: Recording Types DVD Audio Video AUDIO-CD Disc Size Max. Playing Time 12 Cm Single-sided 240 min. Double-sided 480 min. - DVD contains excellent sound and video due to Dolby Digital and MPEG2 system. 8 Cm Single-sided 80 min. Double-sided 160 min. - Various screen and audio functions can be easily selected through the onscreen menu. 12 Cm 74 min. 8 Cm 20 min. Audio Characteristics - CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time. Disc Markings Region Number

PAL Play Region Number PAL broadcast system in U.K, France, Germany, etc. Dolby Digital disc STEREO DIGITAL SOUND Stereo disc Digital Audio disc Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this player is described on the rear panel of the player. DTS disc MP3 disc You must only insert one DVD disc at a time. Inserting two or more discs will not allow to play them back and it may cause damage to the DVD player. DivX Certification DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under license

English Disc Types (Logos) Description Front Panel Controls

DISC TRAY Place the disc here.

SKIP ( ) / SEARCH Use to reverse skip a scene or music.

OPEN/CLOSE ( Press to open and close the disc tray.

DISPLAY Operation indicators are displayed here. USB HOST Connect digital still camera, MP3 player, memory stick, Card reader other removable storage devices.

PLAY/PAUSE ( Begin or pause disc play. MIC 1/2 Connect Microphone for karaoke functions.

SKIP ( ) / SEARCH Use to forward skip a scene or music.

10. MICROPHONE VOLUME

Use to adjust microphone volume level. Use the button by pressing it. Turn it to the left or right to control the volume.

STOP ( Stops disc play.

When STANDBY/ON is pressed, the indicator turn on and the player is turned on. Front Panel Display

STOP, PAUSE and OPEN/CLOSE

Displays the Total playing time and various messages concerning operations such as PLAY, STOP, LOAD ... NOdSC: No disc loaded. OPEn: The disc tray is open. LOAd: Player is loading disc information. Rear Panel

- Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver. - Use either an optical or coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder.

- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10 seconds.

- Use a video cable to connect to the Video input jack on your television.

- Connect to an amplifier with 5.1ch analog input jacks.

- Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture. Note - Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN). If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system. - The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input. - There may be no image output if the DVD player is connected to a TV or display that is not compatible with the above format. - Refer to the TV's instruction manual for detailed information regarding the HDMI terminal. - See pages 29 ~ 30 to get more information on how to use the setup menu.

Tour of the Remote Control

VIDEO SEL. Button Selects video output formats. HDMI SEL. Button HDMI Output resolution setup. DVD POWER Button Turns the power on or off. NUMBER Buttons REPEAT Button Allows you to repeat play a title, chapter, track, or disc. BOOKMARK Button SEARCH Buttos (

Allow you to search forward/backward through a disc.

INSTANT REPLAY Button This function is used to replay the previous 10 seconds of a movie from the current position. SKIP Buttons (

Use to skip the title, chapter or track. STOP Button ( TV VOL (+, -) Buttons Control volume. MENU Button Brings up the DVD player’s menu. œ/ƒ,¦/‹ Buttons ENTER/œ This button functions as a toggle switch. EZ VIEW Button The aspect ratio of a picture can easily be adjusted according to the screen size of your TV (16:9 or 4:3). DISC MENU Button Brings up the Disc menu. SUBTITLE Button AUDIO Button Use this button to access various audio functions on a disc. KARAOKE Button Use to begin Karaoke functions. USB Button TV POWER Button Turns the TV’s power on or off. OPEN/CLOSE ( ) Button To open and close the disc tray. REPEAT A-B Button Allows you to repeat play A-B on a disc. STEP Button Advances play one frame at a time. INSTANT SKIP Button This function skips playback ahead 10 seconds. PAUSE Button ( ) Pause disc play. PLAY Button ( ) Begin disc play. TV CH ( ) Buttons Channel selection. TV/VIDEO Button Press to display all of the available video sources ( i.e., TV, Cable, Video) RETURN Button Returns to a previous menu. EXIT Button Exit the on-screen menu. CANCEL Button Use to remove menus or status displays from the screen. ZOOM Button Enlarges the DVD Picture INFO Button Displays the current disc mode. CONNECTIONS The following shows examples of connections commonly used to connect the DVD player with a TV and other components. Before Connecting the DVD Player - Always turn off the DVD player, TV, and other components before you connect or disconnect any cables. - Refer to the user’s manual of the additional components you are connecting for more information on those particular components. Connecting to a TV (SCART) - Using the SCART, connect the SCART (EXT) terminal on the rear of the DVD Player to the SCART (IN) terminal of your TV. - If your TV is not equipped with a SCART you can select one of the following alternative connections: Connecting to a TV (VIDEO CVBS)

Using video/audio cables, connect the VIDEO (yellow)/AUDIO (red and white) OUT terminals of 5.1CH (front L-R) on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV.

Turn on the DVD player and TV. WHITE RED YELLOW Video Cable

RED WHITE Audio Cable Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen. Note - Noise may be generated if the audio cable is too close to the power cable. - If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 12) - The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV. - If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player.

English Choosing a Connection Connecting to a TV with DVI Jack

Using the HDMI-DVI cable (not included), connect the HDMI OUT terminal on the rear of the DVD player to the DVI IN terminal of your TV.

Using the audio cables, connect the AUDIO (red and white) OUT terminals of 5.1CH (front L-R) on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV. Turn on the DVD player and TV. RED WHITE HDMI-DVI cable (Not Included) RED

WHITE Audio Cable Press the input selector on your TV remote control until the DVI signal from the DVD player appears on your TV screen. Connecting to a TV with HDMI Jack

Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal of your TV.

Press the input selector on your TV remote control until the HDMI signal from the DVD player appears on your TV screen. HDMI cable (Not Included) HDMI VIDEO Specifications When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order. The first press of the HDMI SEL. button brings up the current resolution. The second press allows you to change the HDMI output resolution. - Depending on your TV, certain HDMI output resolutions may not work. - Please refer to the user's manual of your TV. - If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds. - If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture quality. - If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC). (See page 32). - If your TV has an logo, then it will Supports the Anynet+ Function.

HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.

• HDMI connection description HDMI connector - Both uncompressed video data and digital audio data (LPCM or Bit Stream data). - Though the player uses a HDMI cable, the player outputs only a pure digital signal to the TV. - If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen.

• Why does Samsung use HDMI? Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. DVI technology is superior because it requires no D/A conversion and is a pure digital signal from the player to your TV.
• What is the HDCP? HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized Connection to an Audio System (2 Channel Amplifier)

Using the audio cables, connect the AUDIO (red and white) OUT terminals of 5.1CH (Front L-R) on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier.

Using the video signal cable(s), connect the VIDEO OUT terminals on the rear of the DVD player to the VIDEO IN terminal of your TV. RED

WHITE Audio Cable Turn on the DVD player, TV, and Amplifier. RED WHITE 2-Channel stereo ampilfier

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Note - Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears. - Please set the audio in the menu screen according to the Amplifier. (See pages 27-29) - The position of terminals can vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

If using an optical cable (not included), connect the DIGITAL AUDIO OUT (OPTICAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (OPTICAL) terminal of the Amplifier. If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.

Using the video signal cable(s), connect the VIDEO or HDMI OUT terminals on the rear of the DVD player to the VIDEO or DVI IN terminals of your TV as described on pages 9 to 11.

Optical Cable (not included) Coaxial Cable (not included) Dolby digital or DTS amplifier

Turn on the DVD player, TV, and Amplifier.

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input. Note - Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears. - Please set the audio in the menu screen according to the Amplifier. (See pages 27 to 29) - The position of terminals can vary depending on the Amplifier. Please refer to the user's manual of the Amplifier. - Please remove the dust cover before using the optical cable (not included) and put the cover on the cable again when it's not used.

Connection to a 5.1CH Analog Amplifier

English If using audio cables for 5.1 CH Analog Amplifier (not included) connect the 5.1CH ANALOG AUDIO OUT terminals on the rear of the DVD player to the 5.1CH ANALOG AUDIO IN terminals of the 5.1CH Analog Amplifier.

Using the video signal cable(s), connect the VIDEO terminals on the rear of the DVD player to the VIDEO terminals of your TV as described on pages 9 to 11.

Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Note - Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears. - Please set the audio in the menu screen according to the Amplifier. (See pages 27-29) - The position of terminals may vary depending on the Amplifier. Please refer to the user's manual of the Amplifier.

Press the STOP ( Playing a Disc Before Play - Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote control. - If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input. After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by pressing the button on the front panel of the unit for more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language. Press

1. Press the OPEN/CLOSE ( ) button. The STANDBY

indicator light goes out and the tray opens.

2. Place a disc gently into the tray with the disc’s label facing

3. Press the PLAY ( ) button or OPEN/ CLOSE ( )

button to close the disc tray. - When you stop disc play, the player remembers where you stopped, so when you press PLAY ( ) button again, it will pick up where you left off.

) button during play.

Press the PAUSE ( ) or STEP button on the remote control during play. - Screen stops, no sound. To resume, press the PLAY ( ) button once again.

7. Step Motion Play (Except CD)

Press the STEP button on the remote control during play. - Each time the button is pressed, a new frame will appear. - No sound is heard during STEP mode. - Press the PLAY ( ) button to resume normal play. - You can only perform step motion play in the forward direction.

Press the SEARCH ( / ) button to choose the play speed between 1/8, 1/4 and 1/2 of normal during PAUSE or STEP mode. - No sound is heard during slow mode. - Press the PLAY ( ) button to resume normal play. Note - If the player is left in the stop mode for more than one minute without any user interaction, a screen saver will be activated. Press the PLAY ( ) button to resume normal play. - If the player is left in the stop mode for more than about 30 minutes, the power will automatically shut off.(Automatic Power-Off Function) - If the player is left for about 5 minutes in pause mode, it will stop. - This ( ) icon indicates an invalid button press. Using the Search and Skip Functions During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection. Searching through a Chapter or Track DVD 2X, 4X, 64X, 128X

2X, 4X, 8X When Playing a DVD/MPEG4

1. During play, press the INFO button on the remote control.

- You can select Info in the function menu by pressing the MENU button.

2. Press the œ/ƒbuttons to select the desired item.

3. Press the ¦/‹ buttons to make the desired setup and then

press the ENTER button. - You may use the number buttons of the remote control to directly access a title, chapter or to start the play back from a desired time. ) button on the

4. To make the screen disappear, press the INFO button

again. Note - The speed marked in this function may be different from the actual playback speed. - No sound is hearing during search mode (Except CD). Note Title Skipping Tracks During play, press the SKIP (

) button. - When playing a DVD, if you press the SKIP ( Chapter Most DVD discs are recorded in chapters so that you can quickly find a specific passage. Time Allows playback of the film from a desired time. You must enter the starting time as a reference.The time search function does not operate on some disc. ) button, it moves to the next chapter. If you press the SKIP (

button, it moves to the beginning of the chapter. One more press makes it move to the beginning of the previous chapter. - When playing a CD in Menu Off mode, if you press the SKIP ( ) button, it moves to the next track. If you press the SKIP ( Audio ) button, it moves to the beginning of the track. One more press makes it move to the beginning of the previous track. To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified. Subtitle Refers to the language of the film soundtrack. In the example, the soundtrack is played in English 5.1CH. A DVD disc can have up to eight different soundtracks. Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 different subtitles.

English During play, press the SEARCH ( remote control for more than 1 second. Using the Display Function Using the Disc and Title Menu Using the Function Menu Using the Function Menu (DVD) Using the Disc Menu

1. Press the MENU button during playback.

1. During the playback of a DVD disc, press the MENU button

on the remote control.

‹ or ENTER button. Press ENTER key for Disc Menu Enter Return Using the Title Menu

on the remote control.

‹ or ENTER button. Return Menu

3. Press the œ/ƒ buttons to select one of the six functions.

Then press the ‹ or ENTER button to access the function. You can also directly select these functions using their respective buttons on the remote control. - INFO - ZOOM - EZ VIEW - BOOKMARK - REPEAT Repeat Play

1. Press the REPEAT button on the remote control.

Repeat screen appears. Menu Note - Depending on a disc, the Title Menu may not work. - Title Menu will only be displayed if there are at least two titles in the disc.

Enter Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc. When playing a DVD Press ENTER key for Title Menu Return Info Zoom Bookmark Repeat EZ View Angle Menu Note - Depending on a disc, the Disc Menu may not work. - You can also use the Disc Menu, using the DISC MENU button on the remote control. Enter

2. Press the œ/ƒ buttons to select Function, then press the

‹ or ENTER button. - Info (See pages 15) - Zoom (See page 20) - Bookmark (See pages 19 to 20) - Repeat (See pages 16 to 17) - EZ View (See pages 17 to 18) - Angle (See pages 19)

2. Press the ¦/‹ buttons to select Chapter, Title or A-B,

then press the ENTER button. - DVD repeats play by chapter or title. - Chapter ( ): repeats the chapter that is playing. - Title ( ): repeats the title that is playing. - A-B: repeats a segment of the disc that you select.

3. To return to normal play, press REPEAT button again, then

01 A - B ENTER REPEAT Note - A-B REPEAT allows you to set point (B) until at least 5 seconds of play back time has elapsed after point (A) has been set. - Depending on a disc, the Repeat function may not work. ADVANCED FUNCTIONS Adjusting the Aspect Ratio (EZ View) To play back using aspect ratio (DVD) Press the EZ VIEW button. - The screen size changes when the button is pressed repeatedly. - The screen zoom mode operates differently depending on the screen setting in the Display Setup menu. - To ensure correct operation of the EZ VIEW button, you should set the correct aspect ratio in the Display Setup menu. (See pages 29 to 30). WIDE SCREEN EZ VIEW Slow Play This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being played etc., so you can study them more closely. When playing a DVD

1. During play, press the PAUSE ( ) button.

2. Press the SEARCH (

) button to choose the play speed between 1/8, 1/4 and 1/2 of normal during PAUSE or STEP mode. If you are using a 16:9 TV For 16:9 aspect ratio discs - WIDE SCREEN Displays the content of the DVD title in 16:9 aspect ratio. - SCREEN FIT The top and bottom portions of the screen are cut off. When playing a 2.35:1 aspect ratio disc, the black bars at the top and bottom of the screen will disappear. The picture will look vertically stretched. (Depending on a type of disc, the black bars may not disappear completely.) - ZOOM FIT The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarge For 4:3 aspect ratio discs - Normal Wide Displays the content of the DVD title in 16:9 aspect ratio. The picture will look horizontally stretched. - SCREEN FIT The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched. - ZOOM FIT The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged. - Vertical Fit When a 4:3 DVD is viewed on a 16:9 TV, black bars will appear at the left and right of the screen in order to prevent the picture from looking horizontally stretched.

1. Press the REPEAT button on the remote control.

2. Press the ¦/‹ buttons to select A-B button.

3. Press the ENTER button at the point where you

want repeat play to start (A). B is automatically highlighted.

4. Press the ENTER button at the point where you

want the repeat play to stop (B). - To return to normal play, press the CANCEL button. If you are using a 4:3 TV For 16:9 aspect ratio discs - 4:3 Letter Box Displays the content of the DVD title in 16:9 aspect ratio. The black bars will appear at the top and bottom of the screen. - 4:3 Pan Scan The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed. - SCREEN FIT The top and bottom portions of the screen are cut off and a full screen appears. The picture will look vertically stretched. - ZOOM FIT The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged. For 4:3 aspect ratio discs - Normal Screen Displays the content of the DVD title in 4:3 aspect ratio. - SCREEN FIT The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched. - ZOOM FIT The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged. Note - This function depends on audio languages are encoded on the disc and may not work. - A DVD disc can contain up to 8 audio languages. - To have the same audio language come up whenever you play a DVD; Refer to “Using the Audio Language” on page 27. Selecting the Subtitle Language You can select a desired subtitle quickly and easily with the SUBTITLE button. Using the SUBTITLE button (DVD/MPEG4)

1. Press the SUBTITLE button. The subtitle languages are

represented by abbreviations. The subtitle changes when DVD the button is pressed Off repeatedly. SUBTITLE Note This function may behave differently depending on the type of disc. MPEG4 External subtitle option will appear, depends the DivX Disc. Selecting the Audio Language Subtitle Selection External Subtitle Off readme.TXT Non-standard fonts are not supported You can select a desired audio language quickly and easily with the AUDIO button. Using the AUDIO button (DVD/MPEG4)

1. Press the AUDIO button. The Audio changes when the

button is pressed repeatedly. The audio languages are DVD represented by

RETURN button. Note - You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button. - This function depends on what subtitles are encoded on the disc and may not work on all DVDs. - A DVD disc can contain up to 32 subtitle languages. - To have the same subtitle language come up whenever you play a DVD; Refer to “Using the Subtitle Language” on page 27. Changing the Camera Angle Using the Bookmark Function When a DVD contains multiple angles of a particular scene, you can use the ANGLE function. Using the ANGLE function (DVD) If the disc contains multiple angles, the ANGLE appears on the screen. This feature lets you bookmark sections of a DVD so you can quickly find them at a later time.

1. During play or pause mode, press the MENU button on the

2. Press the œ/ƒ buttons to select Function, then press the

1. During play, press the MENU button on the remote control.

2. Press the œ/ƒ buttons to select Function, then press the

‹ or ENTER button. Info Zoom Bookmark Repeat Info EZ View Zoom Angle Bookmark Enter Repeat Return Menu EZ View Angle Enter Return Menu

on the remote control to select the desired angle.

3. Press the œ/ƒ buttons to select Bookmark, then press the

4/6 Note - If the disc has only one angle, this feature won’t work. Currently, very few discs have this feature. - Depending on the disc, these functions may not work. Using the Instant Replay/Skip Function Using the Instant Replay function (DVD) If you miss a scene, you can see it again using this function. If you press the INSTANT REPLAY button, the current scene moves backward about 10 seconds, and plays back.

4. When you reach the scene you want to mark, press the

ENTER button. Up to three scenes may be marked at a time.

Note - Depending on a disc, the Bookmark function may not work. Recalling a Marked Scene 1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”.

4. Press the ¦/‹ buttons to select a marked scene.

Using the Instant Skip function (DVD) Use this function to skip playback about 10 seconds ahead of the current scene. Press the INSTANT SKIP button. - Playback will skip ahead 10 seconds. Note Depending on the disc, these functions may not work. CANCEL

CANCEL ) button to skip to the marked scene. Clearing a Bookmark 1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”.

5. Press the CANCEL button to delete a bookmark number.

: Name of currently playing file.

: Current Playback Mode : There are four modes. They can be selected in order by Using the Zoom Function pressing the REPEAT button. Using the Zoom Function (DVD) - Off: Normal Playback - Track: Repeats the current track.

1. During play or pause mode, press the MENU button on the

4. Press the ›/‚ or ¥/Š buttons to select the part of the

screen you want to zoom in on. Press the ENTER button. - During DVD play, press ENTER to zoom in 2X/4X/2X/Normal in order. - Random: Files in the disc will be played in random order.

: AVI file icon. Note - When playing MP3, WMA or JPEG, the Picture Quality and the HDMI Resolution cannot be set. - When playing MPEG4 file, the VIDEO SEL. only work in stop mode. Info Zoom Bookmark Repeat EZ View Angle Enter - Folder: Repeats the current folder Return Folder Selection Menu The folder can be selected both in Stop or Play mode. - To select the Parent Folder Press the RETURN button to go to parent folder, or press the ‚ buttons to select “..” and press ENTER to go to the parent folder. - To select the Peer Folder ‚ buttons to select the desired folder, then Press the ›/‚ press ENTER. Clips Menu for MP3/WMA/ JPEG/ MPEG4/CD Audio CD Audio or discs with MP3/WMA/JPEG contain individual songs and/or pictures that can be organized into folders as shown below. They are similar to how you use your computer to put files into different folders. - To select the Sub-Folder ‚ buttons to select the desired folder, Press the ›/‚ then press ENTER. R oot W MA JPEG P arent Fol der MP 3 MU S IC Open the disc tray. Place the disc on the tray. Close the tray. The tray closes and this screen displays. Stop 1s t 00:00:00 S ub-Fol ders 2nd WMA JPEG MP3

1. Open the disc tray. Place the disc on the tray. Close the tray.

- Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files. ƒ buttons to select a song file.

B e c a u s e Yo u Cactus Sad Dayu Wonderful Enter Return REPEAT Repeat Repeat/Random playback Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track, Folder and Random. - Off: Normal Playback - Track: Repeats the current song file. - Folder: Repeats the song files which have the same extension in the current folder. - Random: Song files which have the same extension will be played in random order. To resume normal play, press the CANCEL button. CD-R MP3/WMA file When you record MP3 or WMA files on CD-R, please refer to the following. - Your MP3 or WMA files should be ISO 9660 or JOLIET format. ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft's DOS and Windows, and with Apple's Mac. This format is the most widely used. - When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension. General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+). - Use a decompression transfer rate of at least 128 Kbps when recording MP3 files. Sound quality with MP3 files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more, only rarely give better sound quality. Conversely, files with decompression rates below 128 Kbps will not be played properly. - Use a decompression transfer rate of at least 64Kbps when recording WMA files. Sound quality with WMA files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps will not be played properly. - Do not try recording copyright protected MP3 files. Certain "secured" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows Media (registered trade mark of Microsoft Inc) and SDMI (registered trade mark of The SDMI Foundation). You cannot copy such files. - Important: The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings, or as an assurance of sound quality. You should note that certain technologies and methods for MP3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files). - This unit can play a maximum of 500 files and 500 folders per disc. MPEG4 Playback MPEG4 Play Function AVI files are used to contain the audio and video data. Only AVI format files with the “.avi” extensions can be played.

1. Open the disc tray. Place the disc on the tray.

Close the tray. ƒ or ¦/‹ ‹ buttons to select an avi file

a01_divx51b-8 a02_divx505b-8 a03_divx502sp-8 a04_divx412-8 Enter Return Menu Repeat playback Press the REPEAT button to change playback mode. There are 3 modes, such as Off, Folder and Title. - Folder : repeats the AVI files which have the same extension in the current folder. - Title : repeats the title that is playing.

English MP3/WMA/CD Audio Playback This unit supports all resolutions up to maximum below. Repeat A-B playback Press the REPEAT A-B button to set the point where you want repeat play to start (A). Press the REPEAT A-B button again at the point where you want the repeat play to stop (B). - To return to normal play, press the CANCEL button. Note - A-B REPEAT does not allow you to set point (B) until at least 5 second of playback time has elapsed after point (A) has been set DivX3.11 & DivX4 & XviD DivX5 Bitrate may fluctuate: Device may skip decoding the high bitrate portions and begin decoding again when Bitrate returns to normal. 720 x 480 @30fps 720 x 576 @25fps : Maximum bitrate : 4Mbps Possible warning messages that may appear when trying to play DivX/AVI files are :

During play, press the button, it moves forward or backward 5 minutes. During play, press the SEARCH

) button and press again to search at a faster speed. Allows you to search at a faster speed in an AVI file. (2X, 4X, 8X) Allows you to search at a slower speed in an AVI file. (1/8X, 1/4X, 1/2X) Each time the STEP button is pressed, a new frame will appear.

Slow Motion Play Step Motion Play Reference page This player is not authorized to play this video

2. Unsupported Codec

- Files with certain Codec Types, Versions (ex. MP4, AFS and other proprietary codecs) are not suppoerted by this player. Stop NOCODEC Off S w e e t Vo l 3 P 14

B e c a u s e Yo u Cactus ZOOM 2X/4X/2X/Normal in order P 20 Sad Dayu Wonderful S w e e t Vo l 3 - These functions may not work depending on MPEG4 file. CD-R AVI file This unit can play the following video compression formats within the AVI file format: - DivX 3.11 contents - DivX 4 contents (Based on MPEG-4 Simple Profile) - DivX 5 contents (MPEG-4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also supported.) - XviD MPEG-4 compliant Contents. Enter Menu Return

3. Unsupported Resolution

- Files containing resolutions higher than the player’s specification are not supported. Stop NOCODEC Off /a01_divx51b-8

• The resolution that can be supported by DVD1080PK model up to 720 x 480 @30 frames/ 720 x 576 @25 frames
• This unit supports CD-R/RW written in MPEG4 in accordance with the “ISO9660 format”. Playing Media Files Using the USB Host feature You can enjoy the media files such as pictures, movies and To play back the disc at a faster speed, press

• Each time you press either button, the playback speed will change as follows : 2x ➞ 4x ➞ 8x. camera in high audio by connecting the storage device to the USB port of the DVD Player. Using the USB HOST feature

1. Connect the USB device to the USB port on the front of the

2. If there is partision Of USB, Press the ›/‚

select the one of partision from USB, then Press ENTER. Disc USB ‚ or ¥/Š Š buttons to select a file in USB.

Press ENTER to Open file. Off Compatible Devices

1. USB devices that support USB Mass Storage v1.0.

(USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.)

2. MP3 Player: HDD and flash type MP3 player.

3. Digital camera: Cameras that support USB Mass Storage

• Cameras that operate as a removable disk in Windows (2000 or later) without additional driver installation.

4. USB HDD and USB Flash Drive: Devices that support

• You may experience a difference in playback quality when you connect a USB1.1 device.
• For a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for proper operation.

5. USB card Reader: One slot USB card reader and Multi slot

• Depending on the manufacturer. the USB card reader may not be supported.
• If you install multiple memory devices into a multi card reader, you may experience problems.

6. If you use a USB extension cable, the USB device might not

• Supported Formats Enter Return Menu Note
• Each time the USB button on the remote control is pressed, a frame of the USB device selection will appear.
• “USB” appears on the display screen.
• USB MENU screen appears on the TV screen and the saved file is played. To prevent damage to the memory stored in the USB device, perform safe removal before disconnecting the USB cable. ) button - Remove the USB cable. Skip Forward/Back During playback, press the (

• When there is more than one file, when you press the button, the next file is selected.
• When there is more than one file, when you press the button, the previous file is selected. File extension JPG MP3 Bit Rate Version Pixel JPG .JPEG

• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or require additional program installation when connected to a PC are not supported.
• A device using NTFS file system is not supported. (Only FAT 16/32 (File Allocation Table 16/32) file system is supported.)
• Some MP3 players, when connected to this product,may not operate depending on the sector size of their file system.
• The USB HOST function is not supported if a product that transfers media files by its manufacturer-specific program is connected.
• Does not operate with Janus enabled MTP(Media Transfer Protocol) devices.
• The USB host function of this product does not support all USB devices. For information on the supported devices, see page 35.

English tunes saved in an MP3 player, USB memory or digital Stop Fast playback Picture CD Playback CD Ripping This feature lets you to copy audio files from disc to USB device into MP3 format. Stop Open the disc tray. Off Track 01

00:00:00 Track 01 Place the Audio CD(CD DA) disc on the tray, and close the tray. Connect the USB device to the USB port on the front of the unit. Track 02 DEV : SELECT START Track 03 Track 04 Track 05

1. Select the desired folder.

‚ buttons to select a Picture file in the clips

menu and then press the ENTER button.

3. Press the INFO button on the remote control to select the

menu you want to view and then press the ENTER button. Track 06 Track 07 Track 08 ENTER RETURN Enter Menu This screen will displayed.

1. With the unit in Stop mode, press the Š button to select the

Note - Press the STOP button to return to the clips menu. - When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu. DEV (storage media device) menu, then press ENTER button. ‚ buttons to select SELECT, then press the

ENTER button to marked all files to be copying. Rotation - To unmarked copying all files press ENTER button again.(UNSELECT Menu) : Each time the ENTER button is pressed, the picture rotates 90 degrees clockwise. - If you want to marked several files to be copying, press the ¥ button, then press ENTER button on the selected file. Stop Zoom ‚ buttons to select the part of the : Press the ›/‚ screen you want to zoom in on. Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X. Off Disc Track 01

• Before beginning the Slide Show, the picture interval must be set. File copy begins. - To cancel the copying in progress, press the CANCEL but ton. Play

: When this icon is selected and ENTER is pressed, the pictures change automatically with about a 6 second interval.

: The pictures change automatically with about a 12 second interval.

: The pictures change automatically with about a 18 second interval. Off Track 01

00:00:00 Track 01 Track 02 DEV : USB 1 UNSELECT Track 03 Track 04 Track 05 Ripping START Track 06 Track 07 CANCEL Cancel Track 08 Ripping Enter REPEAT Repeat TIMER: ENTER RETURN Note - When the CD ripping being processed the player will atoumatic in play mode. - Only the Audio CD(CD DA) dics can be ripping.

Note - Depending on a file size, the amount of time between each picture may be different from the manual. - If you don’t press any button, the slide show will start automatically in about 10 seconds by default. MP3-JPEG Playback ‚ buttons to select an MP3 file in the clips

clips menu and then press the ENTER button. - Music willplay from the beginning

3. Press Stop button when you want to stop the

playback. Note MP3 and JPEG files have to be on the same disc. CD-R JPEG Disc - Only files with the “.jpg” and “.JPG” extensions can be played. - If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played. - Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played. - The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters (. / = +). - Only a consecutively written multi-session disc can be played. If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment. - A maximum of 3000 images can be stored on a single CD. - Kodak Picture CDs are recommended. - When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played. - Kodak Picture CD: The JPEG files in the pictures folder can be played automatically. - Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu. - Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu. - QSS Picture CD: The unit may not play QSS Picture CD. - If the number of files in 1 Disc is over 500, only 500 JPEG files can be played. - If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played KARAOKE FUNCTIONS Karaoke Functions Operation Sequence

1. Connect the Mixed Audio Out terminals with the TV or

Amplifier. (see page 9)

2. Connect Mic into Mic jack. When a MIC is connected, the

karaoke functions can be used. Key Control

1. Playback the Karaoke Disc containing the wanted songs.

Press the KARAOKE button. Š buttons to change the desired tone.

Keycon Note - If you hear feedback(squealing or howling) while using the karaoke feature, move the microphone away from the speakers or turn down the microphone volume or the speaker volume. - When playing MP3, WMA, DTS and LPCM disc, the karaoke functions will not operate. - When the MIC is connected, Digital Out does not work. - The MIC sound outputs only from Analog Audio Out. - If MIC is connected to the MIC jack on the front panel, 5.1CH audio will be changed in to 2 CH audio automatically, this condition can't be change unless the MIC is plugged out.

English You can play JPEG using music as a backgound. Setting Up the Language Features CHANGING SETUP MENU If you set the player menu, disc menu, audio and subtitle language in advance, they will come up automatically every time you watch a movie. Using the Setup Menu Using the Player Menu Language The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.

Anynet+(HDMI-CEC):On Enter Return LANGUAGE SETUP Menu ❶ Language Setup: Setup of the Language. ❷ Audio Setup : Setup of the Audio Options. ❸ Display Setup : Setup of the Display Options. Use to select which type of screen you want to watch and several display options. ❹ Parental Setup : Setup of the Parental Level. Allows users to set the level necessary to prevent children from viewing unsuitable movies such as those with violence, adult subject matter, etc. ❺ Divx(R) Registration : Please use the Registration code to register this player with the DivX(R) Video On Demand format. To learn more go to www.divx.com/vod. ❻ Anynet+(HDMI-CEC): Setup of the Anynet+(HDMI-CEC) Options. ƒ buttons to access the different features.

Press the ‹ or ENTER button to access the sub features.

3. To make the setup screen disappear after setting up, press

the MENU button again. Note Depending on the disc, some Setup Menu selections may not work.

1. With the unit in Stop mode, press the MENU button.

ƒ buttons to select Setup, then press the ‹

ƒ buttons to select Setup, then press the ‹

then press the ‹ or ENTER button. - If the selected language is not recorded on the disc, the original pre-recorded language is selected. - The language is selected and the screen returns to Language Setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP Player Menu Disc Menu Audio Subtitle DivX Subtitle Enter

press the Š or ENTER button. - Select “Original” if you want the default soundtrack language to be the original language the disc is recorded in. - If the selected language is not recorded on the disc, the original pre-recorded language is selected. - The language is selected and the screen returns to Language Setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP Player Menu Disc Menu Audio Subtitle DivX Subtitle Enter Original √ English Français Deutsch Español Italiano Return Menu Using the Subtitle Language

then press the Š or ENTER button. - Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio language. - Some discs may not contain the language you select as your initial language; in that case the disc will use its original language setting. - The language is selected and the screen returns to setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP Player Menu Disc Menu Audio Subtitle DivX Subtitle Enter √ Automatic English Français Deutsch Español Italiano Return

then press the ENTER button to set the speaker. AUDIO SETUP Digital Out PCM Down Sampling : On Output Channel : 5.1Ch HDMI - If your TV is not compatible with compressed multichannel formats (Dolby Digital, DTS, MPEG), you should set Digital Audio to PCM. - If your TV is not compatible with LPCM sampling rates over 48kHz, you should set PCM Down sampling to On. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc. Surround Sound Speaker Setup

Speaker Setup Note : - Even when PCM Down sampling is Off

• Some discs will only output down sampled audio through the digital outputs. Note : - To make speaker setup menu appear, select output channel to 5.1CH.
• If you select the 5.1 Channel, connect the RCA cable to the C&LFE connections for analog audio.
• If you select the 2 Channel option, connect the cable to the FR&FL connections. - There is no analog audio output when you play a DTS sound disc. - To make the Setup menu disappear, press the MENU button. : PCM Dynamic Compression : On Enter ➎ Output Channel - 2CH : Select this when using 2 channel connection only. - 5.1CH : Select this when using 5.1channel connection. : PCM MPEG-2 Digital Out Test Small

Small Enter Small User Small Return Menu Note To make the setup menu disappear, press the MENU button. The default settings : FRONT L, R (Small), CENTER (Small), SURROUND (Small). Select the size of the speakers to be connected. ❶ Front (FL, FR) - Large: Normally select this. - Small: When the sound distorts or the suround sound effects are difficult to hear, select this. This activates the Dolby Digital bass redirec tion circuitry and outputs the bass frequencies of the speaker from the subwoofer. ❷ Center - None: If you do not connect a center speaker, select this. - Large: Normally select this. - Small: When the sound distorts, select this. This activates the Dolby Digital bass redirection circuitry and outputs the bass frequencies of the center speaker from other speakers. ❸ Surround (SL, SR) - None: If you do not connect a center speaker, select this. - Large (Rear/Side): Normally select either of these according to the rear speaker’s position. - Small (Rear/Side): When the sound ditorts or the surround sound effects are dificult to hear, select either of these according to the rear speaker’s position. This activates the Dolby Digital bass rediretion circuitry and outputs the bass frequencies of the rear speaker from other speakers. Setting up Test DISPLAY SETUP Aspect Ratio TV Aspect The test output signals come clockwise starting from the Front Speaker(L). Adjust Channel Balance so that speakers output equally in your room.

Return Menu These options will help prevent picture shake in still mode and display small text clearer. Note To make the Setup menu disappear or return to menu screen during set up, press RETURN button. - Auto : When selecting Auto, Field/Frame mode will be automatically converted.

• The subwoofer test output signal is lower than the other speakers.
• The MPEG Multichannel logo is a trademark registered by PHILIPS Corporation.
• If you set Front (L, R) “Small”, LFE (Subwoofer) is set “On” automatically. - Field : Select this feature when the screen shakes in the Auto mode. - Frame : Select this feature when you want to see small letters more clearly in the Auto mode. ❸ Screen Messages Use to turn on-screen messages On or Off. ❹ TV System - NTSC : In case of using NTSC disc Setting Up the Display Options

• If your TV system only has PAL-Video input, you must choose “PAL”. When you choose “PAL”, Interlace output format is PAL 60 Hz output. Display options enable you to set various video functions of the player.

• If your TV system only has NTSC, input you must choose “NTSC ”.

• If you set up the NTSC TV, HDMI output frame rate is 60 Hz. - PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input, you must choose “NTSC”.
• If your TV system only has PAL input, you must choose “PAL ”.
• If you set up the PAL TV, HDMI output frame rate is 50 Hz . Language Setup

HDMI Enter Return ❶ TV Aspect Depending on a type of television you have, you may want to adjust the screen setting (aspect ratio). - 4:3 Letter Box : Select when you want to see the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen. - 4:3 Pan&Scan : Select this for conventional size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.) - 16:9 Wide : You can view the full 16:9 picture on your wide screen TV.

Picture Quality Menu Enter Return Menu ❺ Video Output Select Video Output. - P-SCAN : Select when you want to use Component Progressive (525p) Out. - SCART-CVBS : Select when you want to CVBS output from scart connection. - SCART RGB Output : Select when you want to use Scart Out.

• If you press the VIDEO SEL. button, Video output mode is changed in regular sequence in no disc mode. (P-SCAN ➝ SCART CVBS ➝ SCART RGB)

• If the Yes/No selection in the Display Setup sub Menu is not made within 10 seconds, the screen returns to the previous menu. ❻ HDMI This setting is used when the unit is connected by HDMI to Display devices (TV, Projector, etc.). - Resolution Setting - Auto : Resolution setting automatically - Manual : Resolution setting manually - Resolution

• Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen may be blocked.
• The resolutions available for HDMI output depend on the connected TV or projector. For details, see the user’s manual of your TV or projector.
• When the resolution is changed during playback, it may take a few seconds for a normal image to appear.
• If you set the HDMI output resolution 720p, 1080p or 1080i, HDMI output provides better picture quality. Setting Up the Parental Control To make the setup menu disappear, press the MENU button. For example, if you select up to Level 6, discs that contain Level 7,8 will not play.

1. With the unit in Stop mode, press the MENU button.

ƒ buttons to select Setup, then press the ‹

or ENTER button. Changing the Password

ƒ buttons to select Setup, then press the ‹

press the ‹ or ENTER button. Enter your new password. Re-enter the new password again. : Kids Safe PARENTAL SETUP Change Password Rating Level :Kids Safe Change Password Enter Return Menu

5. Enter your password.

- By default, password is set to 0000. Please change password to other than 0000 to activate parental control function. Enter Return Menu PARENTAL SETUP Rating Level :Kids Safe Change Password PARENTAL SETUP Rating Level Enter Password : Kids Safe Change Password Enter Password Enter Return Menu PARENTAL SETUP Enter Return Menu ƒ buttons to select the Rating Level you want,

English The Parental Control function works in conjunction with DVDs that have been assigned a rating, which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc. Setting Up the Rating Level Setting Up the Anynet+(HDMI-CEC) Note To make the Setup menu disappear, press the MENU button. Anynet+ is a function that can be used to operate the unit using a Samsung TV remote control, by connecting the DVD 1080PK to a SAMSUNG TV using a HDMI Cable. (see page 10-11) (This is only available with SAMSUNG TVs that support Anynet+).

• You can operate the DVD Player by using TV remote control. (TV buttons that can be used to con trol the DVD Player :

Select On when you connecting the DVD-1080PK with Samsung TV that support Anynet+. Language Setup

4. Set the Anynet+(HDMI-CEC) to “On” on your DVD Player,

5. Set the Anynet+ function at your TV. (See the TV instruction

manual for more information.).

• When you press Anynet+ button on the TV remote control, the below OSD will appear. DVDP View TV

,and buttons, - Select Device : Use this option to select device.

buttons.). - Menu on Device : Same as MENU button on the DVD Player remote control. - Device Operation : Same as INFO button on the DVD Player remote control. Note

• By pressing the PLAY button of the unit while watching TV, the TV screen will change to the play screen.
• If you play a DVD when the TV power is off, the TV will power On.
• If you turn the TV off , the DVD Player will power off automatically.
• If you change the HDMI to other sources (Composite,Component,... etc) in TV while play ing the DVD disc, the DVD Player will stop play ing. REFERENCE Introduction

2. Press the ¦/‹ buttons to select Total, then press the

ENTER button. Old Version : 071109V1.B.1080PKXEG Samsung will often support the software upgrade to improve the performance of this unit to the latest status, through Samsung Internet Site (www.samsung.com). Because the specially new mpeg4 codec continues and it is appearing. What improvements are made depends on the upgrade software you are using as well as the software that your DVD-player contained before the upgrade. How to make an upgrade disc Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings: New Version : 071204V8.B.1080PKXEG Firmware upgrade starts - In the middle of the writing, the tray will open automatically. After taking out the disc, please wait for about 2 minutes. - If the unit was succesfully updated, the unit will turn off and on after closing the tray automatically. When the unit turns on, this screen will display.

3. Press the number buttons to select the desired language

1. You have to download a new file through Download Center

of Samsung Internet Site (www.samsung.com).

2. Write the file to Disc using CD-RW of your computer.

Note - File System CD-ROM ISO Level - Character set ISO 9660 - Finalized, single session - Write speed low Upgrade procedure

1. Open the disc tray. Place the disc on the tray. Close the

English Firmware upgrade Troubleshooting Before requesting service (troubleshooting), please check the following. Action Problem Page No operations can be performed with the remote control.

• Check the batteries in the remote control. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain the microprocessor inside the remote control to reset it. Reinstall batteries and try to operate the remote control again.

• Ensure that the disc is installed with the label side facing up.

5.1 channel sound is

not being reproduced. The icon appears on screen.

• 5.1 channel sound is reproduced only when the following conditions are met. :

1) The DVD player is connected with the proper Amplifier

2) The disc is recorded with 5.1 channel sound.

• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:

1. The DVD’s software restricts it.

2. The DVD’s software doesn’t support the feature (e.g., angles).

3. The feature is not available at the moment.

4. You’ve requested a title or chapter number or search time that is out of range.

P12 P27~29 Disc Menu doesn’t appear. • Check if the disc has a Menu. Play mode differs from the • Some of the functions selected in the Setup Menu may not work properly if the disc is not encoded with the corresponding function. Setup Menu selection. P26~32 The screen ratio cannot be changed.

• The Screen Ratio is fixed on your DVDs. P29~30 No audio.

• Make sure you have selected the correct Digital Output in the Audio Options Menu. P27~29 The screen is blocked

• Press the button (in front panel) for more than 5 seconds under no disc inside. All settings will revert to the factory settings. P14 Forgot password

• Press the button (in front panel) for more than 5 seconds under no disc inside. All settings including the password will revert to the factory settings. Don't use this unless absolutely necessary. If you experience other problems.

• Go to the contents and find the section of the instruction book that contains the explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center. The picture is noisy or distorted

• Make sure that the disc is not dirty or scratched.

• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of DVD player.
• See if the TV supports this 480p/576p/720p/1080i/1080p DVD player. P10~11 Abnormal HDMI output screen.

• If snow noise appears on the screen, it means that TV does not support HDCP (High-bandwidth Digital Content Protection). P10~11

• Check your TV system setup correctly.
• The screen Jitter phenomenon may occur when frame rate is converted from 50Hz to 60Hz for 720P/1080i/1080p HDMI (High Definition Multimedia Interface) Output.
• Please refer to the user’s manual of your TV. P29~30 HDMI output Jitter

USB 2.0 Card Reader for SD/MMC/RS-MMC(3-in-1) USB External HDD Product CUTIE MOMOBAY UX-2 Company Serotech Dvico Type

*: Nominal specification - Samsung Electronics Co., Ltd reserves the right to change the specifications with out notice. - Weight and dimensions are approximate.

&XVWRPHU&DUH&HQWUH32%R[(GLQEXUJK

www.samsung.com Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. PRÉCAUTIONS

DISKLADE OPEN/CLOSE (

00:00:00 USB Track 01 Track 02 Track 03 APP : SELECTEREN START Track 04 Track 05 Track 06 Track 07 Diashow (Slide Show) Track 08 Enter

WIRD EMPFOHLEN, DIE AUSGABE AUF “STANDARD

Weight Dimensions Operating Temperature Range Operating Humidity Range DVD (DIGITAL VERSATILE DISC)