YY4540FD - Machine à café KRUPS - Free user manual and instructions

USER MANUAL YY4540FD KRUPS

Grille repose-tasses

PROBLEMES ET ACTIONS CORRECTIVES PROBLÈME, DYSFONCTIONNEMENT ACTIONS CORRECTIVES FR PROBLÈME, DYSFONCTIONNEMENT ACTIONS CORRECTIVES CAUTION: Please read the safety instructions before using your appliance

Cleaning accessories

The appliance is ready to be used.

Slow flashing: a task is in progress Double flash: a 2 coffee cycle is in process. Empty the coffee grounds collector (a 2 coffee cycle is underway). Empty the coffee grounds collector+ empty the drip tray. Check coffee grounds collector is not missing or incorrectly positioned. Fill tank with water. Check water tank is not missing or incorrectly positioned. Coffee cycle has stopped due to lack of water. Fill tank with water. Double coffee cycle has stopped due to lack of water. Fill tank with water. Cleaning program requested. Cleaning program: cycle in progress. Cleaning program: empty the coffee grounds collector. Descaling program requested. Descaling program: cycle in progress. Descaling program, rinsing cycles: in progress. Request to empty and to fill water tank. Empty the coffee grounds collector before the long rinse cycle. Long rinse request. Long rinse in progress. Constant flashing: operating fault. Alternate flashing: Switching off of the appliance under progress. :

Light double flashing

One beep when pressing ON/OFF: turning on the power on the activated appliance. One beep every ten seconds: the appliance is awaiting instructions from the user. One double beep: the appliance has registered your request and will stop as soon as possible.

Water tank handle/lid

Water tank Coffee grounds collector Coffee outlets with height adjusting handle Removable drip grid and tray Coffee bean container lid

L Steam button M “On/Off” key and light N Coffee volume rotating button O “empty the coffee grounds” and “empty the drip tray” warning light P “Fill water tank” light Q Strong coffee key R Standard coffee key S “Scale removal” light T “Clean” light U “Rinsing/servicing” key

1 Coffee bean container

G Grinding fineness setting knob H Metal grinding wheel I Cleaning inlet J Digital display for parameter setting

W Water level floats

SYMBOL INFORMATION Danger :

Warning against the risk of serious or fatal injuries. The lightning bolt symbol warns against electrical dangers. Attention : Warning against the risks of incorrect operation, damage or destruction of the appliance. Important : General or important note on the operation of the appliance. Warning signals Empty the coffee grounds collector and the drip tray, and wipe clean the area where the coffee drawer sits; the light will remain on if the coffee grounds collector is not properly inserted or if it has been put back in place 4 seconds earlier. Fill water tank

Coffee bean grinding fineness setting

CLEAN Proceed with cleaning

CALC Proceed with scale removal

CLEAN + CALC Carry out a long rinse

Thank you for having purchased this Krups Espresseria Automatic. We are sure you will enjoy both the quality of the coffee it makes and how easy it is to use. Whether you want a short, strong shot of a ristretto, a good espresso, a larger and milder lungo, or a creamy cappuccino, your automatic coffee / espresso machine has been designed so you can enjoy the same quality at home as at the bistro, whatever the time of day and right through the week. Thanks to its Thermoblock System, its 15 bar pump and because it uses real coffee beans that are ground just before the coffee is made, your Espresseria Automatic will give you a drink containing maximum aroma, with a fine creamy golden brown top produced by the natural oils contained in coffee beans. To obtain an espresso at just the right temperature and a nice compact creamy top, we advise you to pre-heat your cup. After a few trial runs you will find the type of mix and roast of the coffee beans that suits your taste. The quality of the water used is obviously another essential factor in the coffee you get. Make sure the water is fresh from the tap (contact with the air tends to make it stale), that it is free from chlorine odours and relatively cold. Espresso coffee is richer in aroma than a conventional filter coffee. Despite its stronger, longer-lasting taste, espresso in fact contains less caffeine than filter coffee.

Number of cups possible

RISTRETTO ESPRESSO Possible volume settings (ml)

2 x 20 to 30 ml in two cycles

2 x 30 to 70 ml in two cycles

2 x 80 to 220 ml in two cycles

Possible strength settings or

BEFORE FIRST USE Preparing the appliance

Pull out and fill the water tank - Fig. 1 and 2.

Put it back in place by pressing firmly and close the lid again - Fig. 3. Open the coffee bean container lid. Add the coffee beans - Fig. 4. Close the coffee bean container lid again. Do not fill the water tank with hot water, milk or any other liquid. If you turn on the appliance when the water light will come on and making an espresso tank is not in place or not correctly filled (under the “min.” level,), the or a cup of coffee will be made impossible. NEVER PUT GROUND COFFEE IN THE COFFEE CONTAINER. It is recommended that you do not use oily, caramelised or flavoured coffee beans for this appliance. These kinds of beans may damage the appliance. Check that the coffee beans do not contain any foreign particles such as grit, as any damage caused by the presence of foreign particles will invalidate the guarantee. Do not put water into the coffee bean container. Remember to fit the drip tray to avoid waste water flowing onto the work surface and staining it or scalding you. Check that your water tank is clean.

Initialisation cycle - total duration: around 3 minutes

Turn on the appliance by pressing the button

- Fig. 5. The light is constant. Put a container with a minimum capacity of 0.6 litres underneath the two coffee outlets and steam nozzle. Press the - Fig. 6 button: the appliance starts the initialisation cycle for rinsing of the steam and coffee circuits. The light flashes. The cycle is finished when the light becomes constant. The appliance is now ready to use. It is preferable to rinse the 2 circuits out at least once after the appliance has not been used for several days. Each time you plug your appliance in, it will carry out an initialisation cycle.

Preparing the grinder

You can choose the strength of your coffee by setting the coffee bean grinding fineness. The finer the grinding setting, the stronger and creamier the coffee should be. Set the desired fineness for grinding by turning the ‘Grinding fineness setting’ knob.Turn to the left for finer grind. Turn to the right for coarser grind.

CHANGE THE SETTING DURING GRINDING. Never force the grinding fineness setting button.

YOUR APPLIANCE IS DESIGNED TO MAKE COFFEE FROM COFFEE BEANS ONLY.

When you first make coffee with the appliance or after a long period of absence or a cleaning or scale removal procedure, a little steam and hot water will come out of the steam nozzle (priming). Splashing or scalding may occur if the coffee outlets are set too high in relation to the size of the cups. Note: The amount of water needed to make an espresso is between 30 and 70 ml. The amount of water needed to make a coffee is between 80 and 220 ml.

Production of an espresso or coffee

Plug in your appliance.

Press the button . The light will flash during the pre-heating and initialisation cycle. The light becomes constant. Put a cup under the coffee outlets. You can lower or raise the coffee outlets to suit the size of your cups - Fig. 7. Select the key to get a strong espresso or the key to get a standard espresso - Fig. 8. You can change the volume of water at any time - Fig. 9. To stop coffee flowing into the cup, you can either again press one of the or , keys or turn the knob to the min. position. The ground coffee is moistened with a little hot water after the grinding stage. A few moments later, percolation as such starts. Beyond a certain amount of coffee in the cup, we recommend - in order to obtain a stronger coffee - to divide your preparation into two separate cycles. Example 2 x 70 ml cycles for a cup of 140 ml.

You can prepare 2 cups of coffee or espresso with your appliance.

Press the button the light flashes during the pre-heating of the appliance The light becomes constant. Place 2 cups under the coffee outlets. You can lower or raise the coffee outlets to suit the size of your cup - Fig. 10. Select the button or according to your choice, by quickly pressing the button twice. The light comes on with a double flash to inform you that you have requested two cups of coffee. The appliance will automatically sequence 2 complete coffee-making cycles. Make sure that you don’t remove the cups after the first cycle. If you press the into account.

button a second time (or the other way round), the second one isn’t taken

PREPARING STEAM Steam froths up the milk to make a cappuccino or a caffe latte, for example, and also heats up liquids. As you need a higher temperature to produce steam than to make an espresso, the appliance runs an additional pre-heating phase for steam.

Plug in your appliance. Press the button: the light flashes during the pre-heating of the appliance. The light becomes constant. Press the button - Fig. 11. The light flashes during the pre-heating. Once the pre-heating is finished, the light stays constant and you can start the steam production by pressing the button again. Press the button again to stop the cycle. The appliance goes back to its initial position if the steam control is not used after 2 mins. BE CAREFUL, BECAUSE THE CYCLE DOES NOT STOP IMMEDIATELY.

EN PREPARING ESPRESSO AND LONG COFFEES Frothing milk

We recommend that you use pasteurised or UHT milk that has been recently opened. Untreated milk does not give the best results. Pour the milk into your milk jug. Immerse the nozzle in the milk - Fig. 12. Initiate the steam function as explained in the paragraph above. Once your milk is frothy enough - Fig. 13 - again press the button to stop the cycle. To remove any milk traces from the steam nozzle, place a container under the nozzle and restart a preparation with steam (around 10 seconds). The steam nozzle can be removed for more intense cleaning. Wash it out with water and a little washing up liquid and a small non-abrasive brush. Rinse and dry it - Fig. 14. Before putting it back, ensure that the air inlet holes are not blocked by any milk residues. If necessary, unblock them using the needle supplied - Fig. 15. Do not wash the steam nozzle in a dishwasher. To interrupt the steam function, simply press any button. If the nozzle is obstructed, unblock it with the needle provided. Steam can be produced for a maximum of 2 minutes per cycle.

After the steam function has been used, the nozzle can be hot, and we recommend that you wait for a few moments before handling it.

Auto-cappuccino XS 6000 Set (sold separately)

This auto-cappuccino accessory enables you to make cappuccinos or lattes - Fig. 16. Connect the different parts to each other. Ensure that you do not pierce the pipe by keeping the button in the correct place.

After removing the lid, fill the jug with milk - Fig. 17 and place a cup or glass under the auto-cappuccino nozzle - Fig. 18. Select the cappuccino or latte position on the special nozzle - Fig. 19. Start the steam, as indicated in the chapter ‘Making drinks with steam’. Once you have made the milk froth, place your cup under the coffee outlets and start a coffee cycle - Fig. 20. To prevent the milk from drying on the auto-cappuccino accessory, ensure that you clean it thoroughly. You are advised to wash it immediately by running a steam cycle with the accessory jug filled with water in order to clean the inside of the nozzle. You can use the KRUPS liquid cleaner for this, available separately.

MAINTAINING YOUR APPLIANCE Emptying the coffee grounds collector and the drip tray.

If the light flashes, Remove, empty and clean the coffee ground collector - Fig. 21. Replace the coffee grounds collector – Fig. 22 Remove, empty and clean the drip tray - Fig. 23. The drip tray is equipped with floats to indicate when it needs to be emptied. Put all parts back in place. As soon as you remove the coffee grounds collector, you will have to empty it completely to avoid any overflow. The light will remain on if the coffee drawer(1) area is not cleaned thoroughly and if the used grounds collector is not pushed firmly into place or is incorrectly installed. You cannot make espresso or coffee while the light is on or is flashing. The coffee grounds collector has a capacity of 9 coffees.

These 2 functions are available anytime, except if the appliance requests a ‘CLEAN’ and/or ‘CALC’ cycle.

Rinsing out the coffee circuit: Place a container under the coffee nozzles. Press the which will automatically stop after around 40 ml.

button - Fig. 6 quickly to start a coffee circuit rinsing cycle,

Rinsing out the steam circuit:

Place a container under the steam nozzle and press the which will automatically stop after around 300 ml.

button for 3 seconds to start a steam circuit rinsing cycle,

EN Appliance cleaning program – total duration: about 13 minutes

When a cleaning operation is necessary, the appliance warns you of this by flashing the ‘CLEAN’ light.

This program is only accessible when the appliance requests it (i.e. approximately every 300 coffees or espressos). o benefit from the guarantee conditions, it is essential to perform the appliance cleaning cycle when inT formed to do so. Be sure to follow the procedure closely, step by step. Only use KRUPS cleaning tablets. You can obtain cleaning tablets from KRUPS Service Centres. When the indicator light flashes, you can continue to use the appliance but it is recommended that you carry out the program as soon as possible. Start the cleaning program by pressing the button. The ‘CLEAN’ light becomes constant and the indicator lights and flash. Remove, empty and clean the coffee ground collector - Fig. 21. Replace the coffee grounds collector – Fig. 22 Remove, empty and clean the drip tray - Fig. 23. Put all parts back in place. The light goes out. Remove, fill and put the water tank back into place. Place a container with a minimum capacity of 0.6l under the coffee outlets - Fig. 24. Open the maintenance hatch - Fig. 25 and insert a KRUPS cleaning tablet (XS3000) in the cleaning duct - Fig. 26. Press the button to start a cleaning cycle. The first phase (approximately 10 min) begins. At the end of this phase, the sound signal emits a beep every 10 seconds and you can empty the used water container and the drip tray. Put the drip tray and container back in place for the next phase. Press the button again to start the final phase. The sound signal stops. Final phase (±3 min) The program continues. It rinses the appliance and removes any traces of cleaner. When the cleaning cycle is finished, the indicator light ‘CLEAN’ goes out. Remove and empty the used water container. Empty the drip tray and put back into place. Refill the water tank. Your appliance is ready for the next use. If there is not enough water in the water tank when you start the program, the light will come on to warn you. Add the appropriate amount of water to the container and cleaning will continue automatically. If you unplug the appliance during cleaning, press the button, or there is an electrical power cut, the cleaning program will start again from the beginning. In this case, another cleaning tablet may be necessary. Make sure to carry out the full cleaning cycle to ensure good maintenance of your appliance. The cleaning cycle is intermittent: do not put your hands under the water outlets ‘E’ and ‘W’ while the cycle is in progress. Only use KRUPS (XS3000) cleaning tablets. We cannot be held responsible for any damage that may result from the use of tablets from other brands. You can obtain cleaning tablets from KRUPS Service Centres.

Scale removal program - total duration: about 20 minutes

The quantity of scale deposited depends on the hardness of the water used. The appliance will automatically warn you by the ‘CALC’ light coming on when you need to proceed with scale removal.

This program is only accessible when the appliance requests it. o benefit from the guarantee conditions, it is essential to perform the appliance’s scale removal cycle T when informed to do so. Be sure to follow the procedure closely step by step. You can continue to use the appliance when the light is on, but you are advised to perform the program as soon as possible.

If your appliances fitted with our Claris - Aqua Filter System F088 cartridge, please remove the cartridge during the descaling operation.

Only use KRUPS scale removal products. You can obtain scale removal products from KRUPS Service Centres. We cannot be held responsible for any damage that may result from the use of tablets from other brands. ake certain to protect your work surface during cleaning and scale removal cycles, especially if it is M made of marble, stone or wood. Start the descaling program by pressing the button. The ‘CALC’ light becomes constant and the indicator lights and flash. Remove and clean the drip tray. Place a container with a minimum capacity of 0.6 l under the coffee outlets as well as under the steam nozzle - Fig. 24. Empty the tank and refill it with warm water up to the line ‘CALC’ - Fig. 33. Dissolve a sachet of Krups (40 g) F054 descaler in the tank - Fig. 33. Replace the water tank. The indicator light switches off. Press the button after carrying out all of these operations. The first phase (approximately 8 min) begins. The descaling cycle will start automatically. At the end of this phase, the sound signal beeps every 10 seconds and the indicator light ’ flashes. Empty the used water container and put it back in place. Empty and rinse the water tank - Fig. 34. Refill the tank with water and put it back into place. The warning light goes out. Press the button again to start the second phase. The sound signal stops. The second phase (about 6 min) begins. The program continues. It rinses the appliance and removes any traces of the descaler. At the end of this phase, the sound signal beeps every 10 seconds Remove and empty your used water container and put it back in place. Press the button again to start the final phase. The sound signal stops. The final phase (approximately 6 min) begins. The program continues. It removes the last particles of descaler. When the descaling cycle is finished, the indicator light ‘CALC’ goes out. Refill your water tank. Your appliance is ready for the next use. If there is not enough water in the water tank, you will be warned by the light. Add the appropriate amount of water to the tank and scale removal will continue automatically. If you unplug the appliance during cleaning, press the button, or there is an electrical power cut, the cleaning program will start again from the beginning. In this case, another cleaning tablet may be necessary. Make sure to carry out the full cleaning cycle to ensure good maintenance of your appliance. The cleaning cycle is intermittent: do not put your hands under the water outlets ‘E’ and ‘W’ while the cycle is in progress.

Long rinsing program – total duration: about 2 minutes

When it is necessary to make a long rinsing program, the appliance warns you of this by flashing the ‘CLEAN’ and

‘CALC’ lights. Remove, fill and replace the water tank. Place a container with a minimum capacity of 0.6 l under the coffee outlets and the steam nozzle. Start the long rinsing program by pressing the button. The lights ‘CLEAN’ and ‘CALC’ become constant and the indicator light starts flashing. When the long rinse is finished, the lights ‘CLEAN’ and ‘CALC’ go out and the indicator light becomes constant. Your appliance is ready for the next use. The appliance can ask you to empty the coffee ground collector.

OTHER FUNCTIONS To switch the appliance off

You can switch off your appliance at any time. As the appliance is switching off, a double beep is emitted and all of the red lights flash, one after the other. The appliance has registered your request and will stop as soon as possible.

To get the best taste from your coffee and extend your appliance’s service life, we advise you to use only the Claris Aqua Filter System cartridge sold as an accessory.

Fig. 30 : Mechanism to indicate the month the cartridge was fitted and when to replace it (after 2 months at most). Installing the cartridge in the appliance. On first use, screw the filter cartridge into the bottom of the water tank - Fig. 31. Place a 0.6 l container under the steam nozzle. Press the button for more than 3 seconds (unless the appliance requires a ‘CLEAN’ and/or ‘CALC’ maintenance). The indicator light flashes. When the installation of the filter cartridge is finished, the indicator light becomes constant. Your appliance is ready for the next use. The Claris cartridge needs to be replaced after about every 50 litres of water or every two months at least. If you are using the Claris – Aqua Filter System cartridge, set the water hardness to level 0.

Connect the appliance to the mains power supply but do not turn it on.

Lift the cup grid by pressing on the back to make it tilt - Fig. 25. Press the and simultaneously - Fig. 27. The digital display for parameter setting is under the servicing flap - Fig. 28. Look down vertically to the bottom of the window - Fig. 29. Proposed settings order: 1. Adjust water hardness 2. Adjust coffee temperature 3. Adjustment of the auto-off function 4. Info

1. Setting water hardness

Appliances are pre-set in the factory for hardness level 4. Before using the appliance for the first time or if you have noted a change in water hardness, it is advisable to adapt the appliance to the water hardness. Please contact your water supplier to find out the water hardness in your area. Degree of hardness

The “water tank” light will come on.

Press the button - Fig. 32 as many times as are needed to select the hardness level for the water used: 0 = very soft, 1 = soft, 2 = moderately hard, 3 = hard, 4 = very hard. To go to the next phase, press the button or to leave the settings mode press .

2. Setting the coffee temperature

Appliances are pre-set in the factory to level 2. The ‘CALC’ light comes on. Press the - Fig. 32 button as many times as are needed to adjust the desired coffee temperature: 1, 2 or 3. To go to the next phase, press the button or to leave the settings mode, press .

3. Setting the automatic electrical power supply cut-off (auto-off)

Appliances are pre-set in the factory to 1 hour. You can set your appliance to turn off after a pre-programmed number of hours. The ‘CLEAN’ light comes on. Press the - Fig. 32 button as many times as necessary to select the desired duration: 1 = 1h, 2 = 2h, 3 = 3h, 4 = 4h. To go to the next phase, press the button, or to leave the settings mode, press .

EN Installation of the filter cartridge - total duration: around 2 min

4. Info (number of cycles)

The light comes on. To go to the next stage, press the To leave settings mode, press .

button. You will go back to adjustment 1.

At any of these stages, you can leave settings mode by pressing the button if you have finished your adjustments. All of the lights will go off. These settings stay applicable even if there is an electric power cut. You can change these settings at any time by repeating these operations.

TROUBLESHOOTING, CORRECTIVE ACTIONS PROBLEM MALFUNCTION CORRECTIVE ACTION Your appliance detects a fault.

Switch off and disconnect the appliance, remove the filter cartridge, wait for a minute and restart the appliance.

The appliance does not turn on when the pressed.

Check your fuses and plug sockets.

Check that the two power plugs are correctly pushed in the socket.

The coffee grinder makes a strange noise.

There is a foreign body in the grinder. Disconnect the appliance before investigating. See if you can extract the foreign body using your vacuum cleaner.

The steam nozzle makes a noise.

Check that the steam nozzle is correctly attached to its corresponding end piece.

The steam nozzle on your appliance seems partially or completely clogged.

Ensure that the opening in the end piece is not obstructed by milk residue or limescale. Unclog the holes with the needle supplied with your appliance.

The steam nozzle makes little or no milk froth.

For milk-based drinks, use very fresh, very cold pasteurised or UHT milk. It is also advisable to use a cold container. If the results do not improve, try changing the brand of milk.

No steam comes out of the nozzle.

Empty the tank and temporarily remove the filter cartridge. Fill the water tank with mineral water which is high in calcium (> 100 mg/l) and run successive steam cycles.

The auto-cappuccino set makes little or no froth.

The auto-cappuccino set does not take in milk.

Check that the accessory is correctly attached to the appliance, remove it then replace it.

Check that the flexible tube is not obstructed or pierced and that it is correctly attached to the accessory so as to make it airtight. Rinse and clean the accessory (refer to the “Auto-cappuccino accessory” chapter).

There is water underneath the appliance.

Before removing the water tank, wait for 15 seconds after the coffee has finished flowing so that the appliance finishes its cycle properly.

Check that the drip tray is correctly positioned on the appliance; it should always be in place, even when the appliance is not in use. Check that the drip tray is not full. The drip tray should not be removed during a cycle. Clean the tank and its connection regularly to avoid the build up of scale, which can cause leaks.

After emptying the coffee grounds collector, the warning message is still displayed on the screen.

Remove the coffee grounds collector and ensure it is empty and clean. Wait at least 6 seconds before replacing, and ensure it is correctly installed.

CORRECTIVE ACTION The coffee dispenses too slowly.

Turn the coffee fineness dial to the right to make the grounds courser (this could also depend on the type of coffee used).

Run one or several rinsing cycles. Change the Claris Aqua Filter System cartridge (see “Installing the filter”).

The water/steam is not dispensed normally from the steam nozzle.

At the beginning or end of making a drink, the steam nozzle may drip slightly.

The coffee fineness dial is difficult to turn.

Only change the grinder setting when it is running.

The espresso or coffee is not hot enough.

Change the coffee temperature setting. Warm the cup by rinsing it with hot water before making the drink.

The coffee is too lightly coloured or too weak.

Avoid using oily, caramelised or flavoured coffee. Check that the coffee bean container has coffee in it and that it is dispensing correctly.

Decrease the drink volume, increase the drink strength. Turn the coffee fineness dial to the left to make the grounds finer. Make the drink in two cycles by using the 2 cups function.

The appliance is not producing coffee.

A problem has been detected during preparation of the drink.

The appliance has restarted automatically and is ready for a new cycle.

Why can I not start the descaling or cleaning program?

Why does my appliance not request to be descaled or cleaned?

The appliance only requests to be cleaned once it has made several types of coffee. The appliance only requests a descaling cycle once it has made a certain number of drinks using steam.

A power failure occurs during a cycle.

The appliance is automatically restarted when power is switched back on.

Coffee flows behind the coffee nozzles.

Pour cold or room-temperature water into the tank. Reduce the temperature level.

The appliance is working but no liquid comes out.

Check that the water tank is in the correct position and that the cord is not jammed between the appliance and the water tank.

Ground coffee is in the drip tray.

Yes, to stay clean the appliance clears ground coffee which has fallen out of the percolation tank.

Danger : O nly a qualified technician is authorised to carry out repairs on the power cord and the electrical system.

Failure to respect this exposes you to fatal injuries due to the presence of electricity. Do not use an appliance that is visibly damaged.

EN PROBLEM MALFUNCTION Here are some recipes you can make using your Espresseria Automatic:

Cappuccino For a cappuccino in the rules of the art, the ideal proportions are as follows: 1/3 hot milk, 1/3 coffee, 1/3 milk froth. Caffe Latte To make coffee with milk, also often called Latte Macchiato, the proportions are as follows: 3/5 hot milk, 1/5 coffee, 1/5 milk froth. -- For these milk-based preparations, it is best to use cold skimmed milk straight from the refrigerator (ideally between 6 and 8° C). -- To finish off, you can sprinkle with cocoa. Café Crème -- Prepare a conventional espresso in a large cup. -- Add a little cream to get a café crème. Café corretto* Prepare a cup of espresso as usual. Then add 1/4 or 1/2 of a liqueur glass of Cognac to taste. -- You can also use anisette, brandy, Sambuca, Kirsch or Cointreau. -- There are many other ways to give some punch to your espresso. -- Just use your imagination. Coffee liqueur* Mix 3 cups of espresso, 250 g of brown sugar candy and 1/2 litre of Cognac or Kirsch in an empty 0.75 litre bottle. Leave the mixture to macerate for at least 2 weeks. -- You will obtain a delicious liqueur. A real treat for coffee lovers Italian style iced coffee 4 scoops of vanilla ice-cream, 2 cups of espresso with sugar to taste, 1/8 l milk, fresh cream, grated chocolate. -- Mix the cold espresso with the milk. -- Serve the scoops of ice-cream into the glasses, pour the coffee onto them and decorate with fresh cream and grated chocolate. Café à la frisonne* Add a small glass of rum to a cup of sweetened espresso. Decorate with a good layer of fresh cream and serve. Flambéed espresso* 2 cups of espresso, 2 small glasses of Cognac, 2 teaspoons of brown sugar, fresh cream. -- Pour the Cognac into heat-resistant glasses, heat and light. -- Add the sugar, mix, pour in the coffee and decorate with fresh cream. Espresso Parfait* 2 cups of espresso, 6 egg yolks, 200g sugar, 1/8 litre of sweetened fresh cream, 1 small glass of orange liqueur. -- Beat the egg yolks with the sugar until it forms a thick, frothy mass. -- Add the cold espresso and the orange liqueur. -- Then mix in the whipped fresh cream. -- Pour the mix into saucer champagne glasses or ordinary. -- Put the champagne glasses in the freezer.

(*: Remember, over-indulgence in alcohol is bad for the health.)

BESCHRIJVING A B C D E F CALC Ontkalk de machine

DRANKEN BEREIDEN KOFFIE RECEPTEN PROBLEMAS E AÇÕES CORRETIVAS PROBLEMA ANOMALIA AÇÕES CORRETIVAS OPIS A B C D E F PROBLEMY I ICH ROZWIĄZANIA PROBLEM NIEPRAWIDŁOWE DZIAŁANIE ROZWIĄZANIE PROBLEM NIEPRAWIDŁOWE DZIAŁANIE ROZWIĄZANIE Zapnuto /

You can set your appliance to turn off after a pre-programmed number of hours.