ManualGo.com MONTECARLO R1 - JANE - Free user manual and instructions
Find the device manual for free MONTECARLO R1 JANE in PDF.
Download the instructions for your in PDF format for free! Find your manual MONTECARLO R1 - JANE and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MONTECARLO R1 by JANE.
USER MANUAL MONTECARLO R1 JANE
INDEX 23_ Parts list 24_ General instructions
Fitting the backrest onto the booster seat
Checking the height of the shoulder belt Choosing where to install the safety seat 27_ Installing the safety seat in the vehicle
25_ Understanding your MONTECARLO R1 car safety seat
Installation with ISOfix anchors and 3-point seat belt
Installation just with 3-point seat belt 30_ Warnings 30_ Recommendations 31_ Maintenance 32_ Information about the guarantee 21
Your new MONTECARLO R1 from JANÉ is a safety seat that has been designed to protect the child in the car from approximately 3 years
(weighing 15 Kg.) up to approximately 12 years old (weighing 36 Kg.). MONTECARLO R1 has passed the strict safety tests of the European Standard ECE 44/04 for groups 2 and 3. MONTECARLO R1 is a safety seat that is used in conjunction with the vehicle 3-point seat belt. It is also fitted with anchor points on the base, which can be fastened to the vehicle ISOfix to achieve greater stability. The MONTECARLO R1 car safety seat can be installed with or without ISOfix anchors although it is advisable to use it with ISOfix anchors as this offers greater comfort and safety. Depending on how it is installed please remember that: If it is used with ISOfix anchors, MONTECARLO R1 is classed as “SemiUniversal”, in other words, you should check to see if it is compatible with your vehicle. To do this, check the Vehicle List that comes with the instructions to see if your car is included. If it is not included, it may be that it has not been checked yet or it may have been checked after the list was printed. You can check the updated list on the web site www.jane.es.
If it is used without ISOfix anchors, MONTECARLO R1 is classed as
“Universal”, in other words, it is compatible with most vehicle seats. However, whenever the vehicle manufacturer states that the seats are suitable for “Universal” type car safety seats this means it is fully compatible. It is very important that you read these instructions carefully before using the MONTECARLO R1 safety seat for the first time. Make sure that everyone who is ever going to use the car seat also knows how to install it and use it properly. It is a known fact that a significant percentage of car seat users do not install them correctly. Understanding the instruction manuals and applying the instructions correctly is as important for your child’s safety as the seat itself.
2. Backrest 3. Headrest 4. Armrest 5. Armrest adjustment button 6. Backrest width adjustment handle 7. Headrest width adjustment handle 8. Headrest height adjustment button 9. Shoulder belt guide 10. Abdominal belt guide 11. ISOfix anchors 12. ISOfix anchor release button 13. ISOfix length release button 14. Ventilation channels 15. Instructions compartment 16. ISOfix end caps
GENERAL INSTRUCTIONS
In order to correctly protect the child and ensure he is comfortable and secure in the vehicle it is necessary to follow the instructions below:
• Not all safety systems are exactly the same, which is why we recommend you try your MONTECARLO R1 out in the vehicle in which it is going to be used.
• Your MONTECARLO R1 car safety seat has been designed to be installed on the back or front seat of your vehicle, provided the car is fitted with 3-point seat belts. However, we recommend that whenever possible you install the safety seat on the back seat of the car, as this position provides maximum safety.
• It is very important not to use second hand products, because JANE can only guarantee complete safety of products used by the original buyer.
• It is only suitable for vehicles that are fitted with automatic 3-point seat belts, that are approved under Standard ECE-16 or other equivalent standards. DO NOT use the safety seat with a 2-point seat belt as this would be very dangerous in the event of sharp braking or an accident.
• In some vehicles the buckle strap of the seat belt can be positioned quite far forwards and may come into contact with the edge of the booster seat, which makes the position unsafe. In this case, try moving the vehicle seat forwards or installing the safety seat on another seat in the car.
• JANE recommends you replace your MONTECARLO R1 car safety seat with a new one if it has been subjected to a lot of strain in an accident.
• Check that all the belts are correctly positioned and fastened to your MONTECARLO R1. Make sure that no belt is twisted. • Make sure the child understands that he should never play with the seat belts or fasteners. • The MONTECARLO R1 safety seat has been designed for use in the car and should not be used out of the vehicle. • For more information on the use and installation of the MONTECARLO R1 consult our web page www.jane.es.
Understanding your MONTECARLO R1 car safety seat
To improve the child’s safety:
• Backrest and headrest with separate width adjustment.
• System to secure it to the vehicle using ISOFIX anchors. These anchors are only used to fasten the seat to the vehicle, the child should be secured with the vehicle 3-point seat belt.
• Reclining seat, fitted with 2 positions.
• Headrest with 6 height positions to ensure maximum protection as the child grows.
• Ventilation system in the frames.
• Higher sides, offering greater protection in the event of side impact.
• Impact absorbing material on the sides and middle of the headrest.
• Adjustable armrests on the booster seat.
Your MONTECARLO R1 safety seat has been designed using the latest safety developments and has been tested under the strictest conditions. It is equipped with the following features:
• Headrest reinforced against twisting.
• To improve the comfort and fit for the child:
1 Fitting the backrest onto the booster seat
MONTECARLO R1 has been designed as a booster seat with a backrest, never use the two parts separately. 1a To fit the backrest onto the booster seat lift the upholstery on the back of the booster seat, hold the backrest in a horizontal position and slot the two legs of the backrest into the holes in the booster seat. 1b Raise the backrest to its vertical position. 1c Fit the locking part onto the back of the backrest legs, it only fits properly in one position, and lastly, fasten it on with the 4 screws. Store the key in the compartment of the locking part in case you need to take it off in the future.
2 Checking the height of the shoulder belt
To ensure maximum safety for the child, the shoulder belt should pass slightly above the shoulder. This position will need to be adjusted as the child grows. 2a Place the child in the seat, make sure he is positioned correctly. The belt should go slightly above the child’s shoulder. 2b To adjust the height, pull the button found behind the headrest (8) and slide the headrest in the required direction. When it is at the correct height, release the button and move the headrest to the nearest locking position, it should click into place. !
WARNING. Check and adjust this position as the child grows.
Choosing the correct place to install the safety seat in the vehicle can reduce the risk of injury to the child in the event of an accident. If possible the safety seat should be installed on the back seat of the vehicle.
There are two possible installations: 1. With Isofix anchors and the 3-point seat belt; follow the instructions in the “semi-universal” section below. Remember that for this safety seat the ISOfix anchors are only used to give the seat greater stability, in the event of an accident the child is restrained with the 3-point seat belt. Also bear in mind that it is “Semi-universal” and not all vehicle seats are compatible, consult the Vehicle List included in a leaflet with the instructions or go straight to our web page www.jane.es/ 2. Just with the 3-point seat belt; follow the instructions in the “Universal” section. In other words, it is compatible with most vehicle seats. However, whenever the vehicle manufacturer states that the seats are suitable for “Universal” type car safety seats this means it is fully compatible. Raise or remove the vehicle headrest if it interferes with the safety seat headrest. On seats fitted with a frontal air-bag, move the seat as far back as possible.
Installing your Montecarlo R1 in the vehicle
3 Semi-universal and Universal installation: Semi-universal: with ISOfix anchors and the 3-point seat belt
Choosing where to install the safety seat
The ISOfix anchors have been designed to safely and easily secure child restraint systems. Not all vehicles are fitted with these anchors, although they are now generally standard in newer models.
Consult the enclosed leaflet to see the vehicle list stating in which vehicles the safety seat can be correctly installed. An updated list can be found on the JANÉ web page (www.jane.es).
If you are going to install your MONTECARLO R1 with the rigid anchors, follow the steps below carefully:
3a First remove the end caps, to do this, pull the anchor button. Keep the end caps in case you use the MONTECARLO R1 without ISOfix in the future. 3b Pull the anchor out pressing the red buttons on the sides (13). 3c Make sure that both anchors are open, the red signal should be displayed on the anchor button (12). Place your MONTECARLO R1 on the vehicle seat in accordance with the advice and warnings contained in the GENERAL INSTRUCTIONS. Before installing the safety seat find the ISOfix anchors on the vehicle seat. Once you have found them, position the MONTECARLO R1 so that the rigid anchors (11) are pointing towards the ISOfix anchors of the vehicle. 3d Press the rigid anchors towards the vehicle seat until they both lock, check that the green signal is displayed on the two ISOfix release buttons (12). 3e Keep pressing firmly until the booster seat touches the backrest of the vehicle seat. Make sure that it is securely held by pulling the seat. 3f Place the child in the MONTECARLO R1 and make sure that he is sitting well back, pass the seat belt over him and fasten it 3g Insert the shoulder belt into the red clip on the headrest (9)
3h Pass the abdominal belt under both armrests of the booster seat, the area where the belt should go is marked in red again (10). Lastly, tighten the seat belt.
To get the child out of the seat, simply unfasten the seat belt. When you want to remove the MONTECARLO R1 safety seat from the vehicle, pull the buttons on the ISOfix anchors (12) while removing the booster seat.
Universal: just with the 3-point seat belt
Place your MONTECARLO R1 on the vehicle seat in accordance with the advice and warnings contained in the GENERAL INSTRUCTIONS.
To protect the upholstery of your vehicle, put the caps on the ISOfix terminalPlace the child in the MONTECARLO R1 and make sure that he is sitting well back, pass the seat belt over him and fasten it.
3f Place the child in the MONTECARLO R1 and make sure that he is sitting well back, pass the seat belt over him and fasten it.
Insert the shoulder belt into the red clip on the headrest (9) 3g Pass the abdominal belt under both armrests of the booster seat, the area where the belt should go is marked in red again (10). 3h Lastly, tighten the seat belt. To get the child out of the seat, simply unfasten the seat belt
4 Reclining the seat:
To offer the child greater comfort the safety seat can be reclined. Maximum safety is achieved when the seat is not reclined.
When it is not in use, DO NOT leave the MONTECARLO R1 seat loose in the vehicle, always secure it with the seat belt or store it in the boot. When you place the child back in the seat again, make sure that none of the straps are twisted or out of place.
4a To recline the seat raise the front part of the booster seat and slide it to the required position. It has 2 positions.
5 Adjusting the width of the sides of the backrest and headrest. 5a To adjust the sides of the backrest and headrest turn the handles found on the side of the seat (6 and 7). Turn the handles clockwise to open the sides and anticlockwise to close them.
Do not recline the seat while the child is using it. To recline or straighten your MONTECARLO R1 safety seat, you should adjust the length of the seat belt. Do this when the vehicle has stopped.
6 Adjusting the armrest.
6a To adjust the armrest (4), press in the middle (5) and turn it to the required position. It has 3 positions.
Do not leave the child unattended.
Any alteration or addition that is made to the product with the correct authorisation of JANÉ may seriously affect the safety of the restraint system. Never add a mattress, pillow or any extra padding to make the child more comfortable as this would alter the safety characteristics of the system. Read these instructions carefully before using the product and keep them for future reference. The baby’s safety may be at risk if these instructions are not followed. This safety device must not be used without the upholstery, nor used with upholstery that is not the original one as it is an important part of the safety characteristics of the system. Check that the safety seat has been fitted correctly. Make sure that the seat belt has not got caught between the folding seats of the vehicle or the doors. It is only suitable for vehicles that are fitted with automatic 3-point seat belts, that are approved under Standard ECE-16 or other equivalent standards. On seats fitted with a frontal air-bag, move the seat as far back as possible. DO NOT use the safety seat with a 2-point seat belt.
Not all safety systems are exactly the same, which is why we recommend you try your MONTECARLO R1 out in the vehicle in which it is going to be used.
It is very important not to use second hand products, because JANÉ can only guarantee complete safety of products used by the original buyer. Do not let other children play unattended near the safety seat. Do not use if any of the parts are missing or broken or torn. Only use the original JANÉ parts. WARNING: Check the road traffic regulations in the country where you are travelling. The use of your child restraint system may be restricted.
RECOMMENDATIONS Keep this instruction book for future reference. Always store it in the compartment under the booster seat.
Inside the vehicle make sure that any luggage or objects that could cause injury in the event of an accident are securely fastened or stored away. The MONTECARLO R1 safety seat should always be secured with the seat belts, even when it is not in use, because in the event of an accident it could get flung about and cause injury to the other occupants of the vehicle.
Do not expose the upholstery to sunlight for prolonged periods of time, when the safety seat is not in use cover it up or store it in the boot.
Clean the plastic parts with soap and warm water, and then dry all the parts thoroughly. The upholstery can be taken off for washing. Follow the instructions below: - Headrest. Release the 2 clasps from the sides, unfasten the strap on the back and pull the upholstery forwards, then release the two clasps from the top part. - Backrest. Unfasten the three straps on the back and the clasps on both sides and then pull the upholstery forwards. - Booster seat. Unfasten the clasps on the back, release the elastic and the two clasps on the front part and then pull the upholstery from the front. For your safety and the good conservation of this product, it is important to bring it to one of our official workshops for regular inspections.
MAINTENANCE Please see link: www.jane.es for more information on how to assemble your new MONTECARLO R1.
INFORMATION ABOUT THE GUARANTEE
This article comes with a guarantee in accordance with the provisions of law 23 / 2003 of 10th July. Keep your receipt as proof of purchase, it is essential to present the receipt in the shop where you bought the product to confirm validity of the guarantee in the event of any problems.
This guarantee excludes any defects or breakages caused by inappropriate use of the article or inobservance of the safety and maintenance rules listed in the instruction pages and on the care labels, as well as faults caused by wear and tear through normal use and daily handling. The label displaying the chassis number of the model should never be taken off, it contains important information. Notice: For the maximum safety and care of your new JANÉ product, it is very important that you complete the registration card found on the web page www.jane.es This registration means we can inform you, if necessary, of the evolution and maintenance of your product. Additionally, if you would like, we can also inform you about new models or news that we think may be useful for you.