PBH 2900 FRE - Rotary hammer BOSCH - Free user manual and instructions

USER MANUAL PBH 2900 FRE BOSCH

Power Tools Division

70745 Leinfelden-Echterdingen

Germany

www.bosch-pt.com

1619929764(2010.11)PS/126 WEU

WEU

PBH

2000 RE | 2000 SRE

BOSCH

Dr. Egbert Schneider
Dr. Eckerhard Ströttgen
Senior Vice President
Head of Product
Engineering
Certification

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Montage

General Power Tool SafetyWarnings

WARNING

Read all safety warnings and all instructions. Failure to follow

the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

English | 17

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be re-paired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Hammer SafetyWarnings

Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
- Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fastener may contact hidden wiring. Cutting accessory and fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance.

Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock.

• When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more secure with both hands.
• Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.
  Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool.

Products sold in GB only: Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the same fuse rating as the original plug.

18 | English

The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.

Products sold in AUS and NZ only: Use a residual current device (RCD) with a rated residual current of 30mA or less.

Functional Description

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Intended Use

The machine is intended for hammer drilling in concrete, brick and stone, as well as for light chiselling work. It is also suitable for drilling without impact in wood, metal, ceramic and plastic. Machines with electronic control and right/left rotation are also suitable for screwdriving.

Product Features

The numbering of the product features refers to the illustration of the machine on the graphics page.

1 SDS-plus tool holder
2 Dust protection cap
3 Locking sleeve
4 Handle (insulated gripping surface)
5 Lock-on button for On/Off switch
6 On/Off switch
7 Rotational direction switch
8 Mode selector switch
9 Button for depth stop adjustment
10 Wing bolt for adjustment of auxiliary handle
11 Auxiliary handle (insulated gripping surface)
12 Depth stop
13 Key type drill chuck
14 Extraction sleeve of the dust extraction attachment

15 Clamping screw for the dust extraction attachment
16 Depth stop of the dust extraction attachment
17 Telescopic pipe of the dust extraction attachment
18 Wing bolt of the dust extraction attachment
19 Guide pipe of the dust extraction attachment
20 Universal bit holder with SDS-plus shank

*Accessories shown or described are not part of the standard delivery scope of the product. A complete overview of accessories can be found in our accessories program.

Noise/Vibration Information

Measured sound values determined according to EN 60745.

Typically the A-weighted noise levels of the product are: Sound pressure level 88 dB(A); Sound power level 99 dB(A). Uncertainty K = 3 dB.

Wear hearing protection!

Vibration total values (triax vector sum) determined according to EN 60745:

Hammer drilling into concrete: Vibrational emission value a_h = 17 m/s^2 , uncertainty K = 1.5 m/s^2 , Chiselling: Vibrational emission value a_h = 15 m/s^2 , uncertainty K = 1.5 m/s^2

Drilling in metal: Vibrational emission value a_h < 2.5 m/s^2 , uncertainty K = 1.5 m/s^2

Screwdriving without impact: Vibrational emission value a_h < 2.5 m/s^2 , uncertainty K = 1.5 m/s^2 .

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.

English | 19

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Technical Data

Rotary Hammer		PBH 2000 RE	PBH 2000 SRE
Article number		3 603 C44 3..	3 603 C44 3..
Speed control		●	●
Stop rotation		●	●
Right/left rotation		●	●
Delivery Scope
- Key type drill chuck		-	●
Rated power input	W	550	550
Output power	W	270	270
Impact rate	min-1	0-5800	0-5800
Impact energy per stroke according to EPTA-Procedure 05/2009	J	1.5	1.5
Speed	min-1	0-2300	0-2300
Tool holder		SDS-plus	SDS-plus
Spindle collar diameter	mm	43 (Euro-Norm)	43 (Euro-Norm)
Drilling diameter, max.:
- Concrete	mm	20	20
- Steel	mm	13	13
- Wood	mm	30	30
Weight according to EPTA-Procedure 01/2003	kg	2.2	2.2
Protection class		☐ / II	☐ / II

The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.

Declaration of Conformity

We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 2006/42/EC.

Technical file at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Assembly

Before any work on the machine itself, pull the mains plug.

Auxiliary Handle

Operate your machine only with the auxiliary handle 11.

Changing the position of the auxiliary handle (see figure A)

The auxiliary handle 11 can be set to any position for a secure and low-fatigue working posture.

• Turn the wing bolt for adjustment of the auxiliary handle 10 in anticlockwise direction and set the auxiliary handle 11 to the required position. Then tighten the wing bolt 10 again in clockwise direction.

Adjusting the Drilling Depth (see figure B)

The required drilling depth X can be set with the depth stop 12.

• Press the button for the depth stop adjustment 9 and insert the depth stop into the auxiliary handle 11. The knurled surface of the depth stop 12 must face downward.
• Insert the SDS-plus drilling tool to the stop into the SDS-plus tool holder 1. Otherwise, the movability of the SDS-plus drilling tool can lead to incorrect adjustment of the drilling depth.
• Pull out the depth stop until the distance between the tip of the drill bit and the tip of the depth stop correspond with the desired drilling depth X .

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus tools are required that are inserted in the SDS-plus drill chuck.

For drilling without impact in wood, metal, ceramic and plastic as well as for screwdriving, tools without SDS-plus are used (e.g., drills with cylindrical shank). For these tools, a keyless chuck or a key type drill chuck are required.

Changing the Key Type Drill Chuck

To work with tools without SDS-plus (e.g., drills with cylindrical shank), a suitable drill chuck must be mounted (key type drill chuck or keyless chuck, accessories).

Inserting the Key Type Drill Chuck (see figure C)

Clean the shank end of the adapter shank and apply a light coat of grease.
- Insert the key type drill chuck with the adapter shank into the tool holder with a turning motion until it automatically locks.
- Check the locking effect by pulling the key type drill chuck.

Removing the Key Type Drill Chuck

Push the locking sleeve 3 toward the rear and pull out the key type drill chuck 13.

Changing the Tool

The dust protection cap 2 largely prevents the entry of drilling dust into the tool holder during operation. When inserting the tool, take care that the dust protection cap 2 is not damaged.

A damaged dust protection cap should be changed immediately. We recommend having this carried out by an after-sales service.

Inserting SDS-plus Drilling Tools (see figure D)

The SDS-plus drill chuck allows for simple and convenient changing of drilling tools without the use of additional tools.

• Clean and lightly grease the shank end of the tool.
• Insert the tool in a twisting manner into the tool holder until it latches itself.
• Check the latching by pulling the tool.

As a requirement of the system, the SDS-plus drilling tool can move freely. This causes a certain radial run-out at no-load, which has no effect on the accuracy of the drill hole, as the drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure E)

• Push back the locking sleeve 3 and remove the tool.

Inserting Drilling Tools without SDS-plus (see figure F)

Note: Do not use tools without SDS-plus for hammer drilling or chiselling! Tools without SDS-plus and their drill chucks are damaged by hammer drilling or chiselling.

• Insert a key type drill chuck 13 (see "Changing the Key Type Drill Chuck", page 20).
• Open the key type drill chuck 13 by turning until the tool can be inserted. Insert the tool.
• Insert the chuck key into the corresponding holes of the key type drill chuck 13 and clamp the tool uniformly.
• Turn the mode selector switch 8 to the "drilling" position.

Removing Drilling Tools without SDS-plus (see figure G)

• Turn the sleeve of the key type drill chuck 13 with the drill chuck key in anticlockwise direction until the drilling tool can be removed.

Dust Extraction with the Dust Extraction Attachment (Accessory)

Dusts from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one's health. Touching or breathing-in the dusts can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are considered as carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials containing asbestos may only be worked by specialists.

• As far as possible, use a dust extraction system suitable for the material.
• Provide for good ventilation of the working place.
• It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the materials to be worked.

Prevent dust accumulation at the workplace. Dusts can easily ignite.

Mounting the Dust Extraction Attachment (see figure H)

For dust extraction, the dust extraction attachment (accessory) is required. When drilling, the dust extraction attachment retracts so that the attachment head is always close to the surface at the drill hole.

• Press the button for depth stop adjustment 9 and remove the depth stop 12. Press button 9 again and insert the dust extraction attachment into the auxiliary handle 11 from the front.
• Connect an extraction hose (diameter 19 mm, accessory) to the extraction sleeve 14 of the dust extraction attachment.

22 | English

The vacuum cleaner must be suitable for the material being worked.

When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a special vacuum cleaner.

Adjusting the Drilling Depth on the Dust Extraction Attachment (see figure 1)

The required drilling depth X can also be adjusted when the dust extraction attachment is mounted.

• Insert the SDS-plus drilling tool to the stop into the SDS-plus tool holder 1. Otherwise, the movability of the SDS-plus drilling tool can lead to incorrect adjustment of the drilling depth.
• Loosen the wing bolt 18 on the dust extraction attachment.
• Without switching the power tool on, apply it firmly to the drilling location. The SDS-plus drilling tool must face against the surface.
  Position the the guide pipe 19 of the dust extraction attachment in its holding fixture in such a manner that the head of the dust extraction attachment faces against the surface to be drilled. Do not slide the guide pipe 19 further over the telescopic pipe 17 of the dust extraction attachment than required, so that as much as possible of the scale 17 on the telescopic pipe remains visible.
• Retighten the wing bolt 18 again. Loosen the clamping screw 15 on the depth stop of the dust extraction attachment.
• Move the depth stop 16 on the telescopic pipe 17 in such a manner that the clearance X shown in the figure corresponds with the required drilling depth.
• Tighten the clamping screw 15 in this position.

Operation

Starting Operation

Observe correct mains voltage! The voltage of the power source must agree with the voltage specified on the nameplate of the machine. Power tools marked with 230V can also be operated with 220V .

Setting the Operating Mode

The operating mode of the power tool is selected with the mode selector switch 8.

Note: Change the operating mode only when the machine is switched off! Otherwise, the machine can be damaged.

• Turn the mode selector switch 8 to the desired position until it can be heard to latch.

Position for hammer drilling in concrete or stone

Position for drilling without impact in wood, metal, ceramic and plastic as well as for screwdriving

Vario-Lock position for adjustment of the chiselling position

The mode selector switch 8 does not latch in this position.

Position for chiselling

Reversing the Rotational Direction (see figure J)

The rotational direction switch 7 is used to reverse the rotational direction of the machine. However, this is not possible with the On/Off switch 6 actuated.

Right rotation: Push the rotational direction switch 7 rightward to the stop.
Left rotation: Push the rotational direction switch 7 leftward to the stop.

Set the direction of rotation for hammer drilling, drilling and chiselling always to right rotation.

Switching On and Off

• To start the machine, press the On/Off switch 6.
• To lock the On/Off switch, keep it pressed and additionally push the lock-on button 5.
• To switch off the machine, release the On/Off switch 6. When the On/Off switch 6 is locked, press it first and then release it.

Setting the Speed/Impact Rate

The speed/impact rate of the switched on power tool can be variably adjusted, depending on how far the On/Off switch 6 is pressed.

Light pressure on the On/Off switch 6 results in low speed/impact rate. Further pressure on the switch increases the speed/impact rate.

Safety Clutch

If the tool insert becomes caught or jammed, the drive to the drill spindle is interrupted. Because of the forces that occur, always hold the power tool firmly with both hands and provide for a secure stance.
If the power tool jams, switch the machine off and loosen the tool insert. When switching the machine on with the drilling tool jammed, high reaction torques can occur.

Working Advice

Changing the Chiselling Position (Vario-Lock)

The chisel can be locked in 36 positions. In this manner, the optimum working position can be set for each application.

• Insert the chisel into the tool holder.
• Turn the mode selector switch 8 to the "Vario-Lock" position (see "Setting the Operating Mode", page 22).
• Turn the tool holder to the desired chiselling position.
• Turn the mode selector switch 8 to the "chiselling" position. The tool holder is now locked.
• For chiselling, set the rotation direction to right rotation.

Inserting Screwdriver Bits (see figure K)

Apply the power tool to the screw/nut only when it is switched off. Rotating tool inserts can slip off.

To work with screwdriver bits, a universal bit holder 20 with SDS-plus shank (accessory) is required.

• Clean the shank end of the adapter shank and apply a light coat of grease.
• Insert the universal bit holder with a turning motion into the tool holder until it automatically locks.
• Check the locking effect by pulling the universal bit holder.
• Insert a screwdriver bit into the universal bit holder. Use only screwdriver bits that match the screw head.
• To remove the universal bit holder, pull the locking sleeve 3 toward the rear and remove the universal bit holder 20 out of the tool holder.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull the mains plug.
For safe and proper working, always keep the machine and ventilation slots clean.
A damaged dust protection cap should be changed immediately. We recommend having this carried out by an after-sales service.

• Clean the tool holder 1 each time after using. If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always include the 10-digit article number given on the type plate of the machine.

24 | English

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can also be found under:

www.bosch-pt.com

Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O.Box 98

Broadwater Park

North Orbital Road

Denham

Uxbridge

UB95HJ

Tel. Service: [phone]

Fax: [phone]

E-Mail: [e-mail]

Ireland

Origo Ltd.

Unit 23 Magna Drive

Magna Business Park

City West

Dublin 24

Tel. Service: [phone]

Fax:[phone]

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: [phone]

Fax: [phone]

Inside New Zealand:

Phone: [phone]

Fax: [phone]

Outside AU and NZ:

Phone: [phone]

www.bosch.com.au

Republic of South Africa

Customer service

Hotline: [phone]

Gauteng - BSC Service Centre

35 Roper Street, New Centre

Johannesburg

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

KZN - BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Western Cape - BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Bosch Headquarters

Midrand, Gauteng

Tel.: [phone]

Fax: [phone]

E-Mail: [e-mail]

Disposal

The machine, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of power tools into household waste!

Only for EC countries:

According the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected

separately and disposed of in an environmentally correct manner.

Subject to change without notice.

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

ppa. Maee i.v. Nogcu

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Montage

Robert Bosch (France) S.A.S.

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Montaje

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

paa. 1. i.v. nuogcu

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Montaggio

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

ppa. Maee i.v. Nogcu

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Bosch Service Center

Telegrafvej 3

2750 Ballerup

Tel. Service Center: [phone]

Fax: [phone]

E-Mail: [e-mail]

Bortskaffelse

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

ppa.

i.v. lojcu

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Montage

Dra stickproppen ur nätuttaget innan arbeiten utfors på elverktyget.

Stödhandtag

Bosch Service Center

Telegrafvej 3

2750 Ballerup

Danmark

Tel.: [phone]

Fax: [phone]

Avfallshantering

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

i.v. Mojgcu

Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen Leinfelden, 19.11.2010

Asennus

IIInpoopoeic yia OpuBo kai dovnoeic

Oi Tiuec metpnoan tou oopou EkaipBwKav kaTaN60745.

H xapaktnpiotikn oTaOu nEknounnC topuunxavnpatoc eKtuihne oupwova e Tnv kaunA kai avepxetai oE: TaOuAnkouotiknc nieo88 dB(A). TaOuAnkouotiknc 1oxuoc 99 dB(A). Avaqalia metpnoc K=3 dB.

Φopâre wtaonidec!

Otiuec kpaabaouw (a0poiavauvuaTaw Tpiowdeltauovewv) EekpiBwOknav oupwa me tynpoiayapn EN 60745:

Tpunmae kpoouon oe mnetov: Tiuh eKtnoounkpaδaμωv ah=17 m/s², avαφλειa K=1,5 m/s²,

KaIeIoua: TUn eknOuNc Kpaδaouw a=15 m/s², avoΦaλεια K=1,5 m/s²,

Tpunmu oetaao: Tui eknoumnc kpaadaoov a_h < 2,5~m / s^2 , aovdai = 1,5m / s^2

Biodu: Tmu nekno npn c kpaedaaov a h<2,5 m/s2, aaoaaleia K=1,5 m/s2.

H 0tA0n Kpa6aouv Nou avapepetai o' autec TIC odnyiec exei metp9ei oupwva ieia diaikaiaoie nponnc tunonoiuev n OTo nlaio Tou npotunou EN 60745 kai npoei va xnpoiomoin-0e ot oukypiion twv diapopwiv nektpikow epyaileiw. Eiva enionc katalnn yia evav npooovio unoloyioo tnC eniapuvoc ano toukpa6aouc.

H 0rAeun Kpaabaovn ou avapepetai avtinpo- ownuei Tc Baoikec xnoieC Tou nEaKtpko epyaleiou. ZnepiTwn, oomega, nou to nEaKtpiko epyaleio thx npoiomointheta i diaopetika, me un poteivoeva epyaleia n xwpic enapk ouvtnpon, tote n 0rAeun kpaabaowmv npoei va eiva ki autn diapopetikn. Auto npoei va auEnoi onavtka tnv eniIapuvan ano touc kpaabaouc kata tn ouvoLki diapkeia oloknpou Tou xpovikou diaotmuoc nou epyaceohe.

Tia nV akpiBn ektiunon Tnc emiPauvon ano Touk kpaDaaouc th npenei va laibavovtai enionc unoyn kaol xpvoi kata Tn diapkeia twv onoiwTu mnxavnu Bpioketal EKTOLeiToupyiac nleitoupyei, xpwic ouwc otny npaypatikotntva xpoimonoileita. Auto mnpoei va meiwoc anuvatik aTv nEiBapuvon ano touc kpaDaaouc kata Tn diapkeia oloknpou Tou xpvikou diaaTma-toc nou epyzce.

Dr. Egbert Schneider
Dr. Eckerhard Strötgen
Senior Vice President
Head of Product
Engineering
Certification

paa

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Sigma

ByaTeToPc ano TnV npizpiv ano onoiadnote epyaia oTo nAektpiko epyaieio.

TpOo0eTn AaBn

XpnojpoieTo nAektpko epyaaleo navtoe e ouvapmooynveyn Tnv npo0etn 11.

Metakivnan tnc npoogetnc laa nce (Blaene eikova A)

H npo0eTn 11 mopei va pu0muotei o e onoiadnotheon enioumeite yia va unopoeet etai va epyoateite aveta kal avanautika.

• Tupiote tn Biδa μe moxlo via tn puθμian tn Cpnoθεntc λaβnc 10 μe φopá avriθεnt twv δeiktwv tou poloayiou kai puθμiote tvn npoθεtn λaβn 11 σtnv επιθμηnt θεσ. Akolouθωc σφiεte tn Biδa μe moxlo 10 yupicovtac tnν μe ωpoloayiakn φopá.

12|Eλλνικα

Pouan aouc npunpaoc (Bene eikova B)

Me tov odnyo athetaouc 12 mopoite va puthetaiaeTo eIthuunrto baooc trpnnmuatoX.

Apaipean tou ypavaawou took

Tnpoume to 6ikaiwa aalayov.

Güvenlik Talimati

Elektrikli El Aletleri icin Genel Uyari Talimati

4UYARI

Dr. Egbert Schneider Senior Vice President Engineering

Dr. Eckerhard Strötgen
Head of Product Certification

i.v. 100gcu

Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 19.11.2010

Montaj

Bosch San. ve Tic. A.S.

Ahi Evran Cad. No:1 Kat:22

Polaris Plaza

80670 Maslak/Istanbul

Müsteri Danismani: [phone]

Müsteri Servis Hatti: [phone]

Tasfiye