DPO4054B - Oscilloscope TEKTRONIX - Free user manual and instructions

USER MANUAL DPO4054B TEKTRONIX

Vertical System Analog Channels

Characteristic	DPO4034B MSO4034B	DPO4054B MSO4054B	DPO4104B MSO4104B
Input Channels	4
Analog Bandwidth (-3 dB) 5 mV/div - 1 V/div	350 MHz	500 MHz	1 GHz
Calculated Rise Time 5 mV/div (typical)	1 ns	700 ps	350 ps
Hardware Bandwidth Limits	20 MHz or 250 MHz
Input Coupling	AC, DC
Input Impedance	1 MΩ ±1%, 50 Ω ±1%
Input Sensitivity, 1 MΩ	1 mV/div to 10 V/div
Input Sensitivity, 50 Ω	1 mV/div to 1 V/div
Vertical Resolution	8 bits (11 bits with Hi Res)
Max Input Voltage, 1 MΩ	300 VRMS CAT II with peaks ≤ ±425 V
Max Input Voltage, 50 Ω	5 VRMS with peaks < ±20 V
DC Gain Accuracy	±1.5%, derated at 0.10%/°C above 30 °C
Channel-to-Channel Isolation	≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to the rated bandwidth for any two channels having equal volts/div settings

Offset Range

Range	1 MΩ	50 Ω
1 mV/div to 50 mV/div	±1 V	±1 V
50.5 mV/div to 99.5 mV/div	±0.5 V	±0.5 V
100 mV/div to 500 mV/div	±10 V	±10 V
505 mV/div to 995 mV/div	±5 V	±5 V
1 V/div to 5 V/div	±100 V	±5 V
5.05 V/div to 10 V/div	±50 V	NA

Vertical System Digital Channels

Characteristic	All MSO4000B Models
Input Channels	16 Digital (D15 - D0)
Thresholds	Per-channel Thresholds
Threshold Selections	TTL, CMOS, ECL, PECL, User Defined
User-defined Threshold Range	±40 V
Maximum Input Voltage	±42 Vpeak
Threshold Accuracy	±(100 mV + 3% of threshold setting)
Input Dynamic Range	30 Vp-p≤200 MHz 10 Vp-p>200 MHz
Minimum Voltage Swing	400 mV
Input Impedance	100 kΩ
Probe Loading	3 pF
Vertical Resolution	1 bit

Horizontal System Analog Channels

Characteristic	DPO4034B MSO4034B	DPO4054B MSO4054B	DPO4104B MSO4104B
Maximum Sample Rate (All channels)	2.5 GS/s	2.5 GS/s	5 GS/s
Maximum Record Length (All channels)	20M points
Maximum Duration at Highest Sample Rate (All channels)	8 ms	8 ms	4 ms
Time Base Range	1 ns to 1,000 s		400 ps to 1,000 s
Time Base Delay Time Range	-10 divisions to 5000 s
Channel-to-Channel Deskew Range	±125 ns
Time Base Accuracy	±5 ppm over any ≥1 ms interval

Horizontal System Digital Channels

Characteristic	All MSO4000B Models
Maximum Sample Rate (Main)	500 MS/s (2 ns resolution)
Maximum Record Length (Main)	20M points
Maximum Sample Rate (MagniVu)	16.5 GS/s (60.6 ps resolution)
Maximum Record Length (MagniVu)	10k points centered around the trigger
Minimum Detectable Pulse Width (Typical)	1 ns
Channel-to-Channel Skew (Typical)	200 ps
Maximum Input Toggle Rate	500 MHz
	Maximum frequency sine wave that can accurately be reproduced as a logic square wave. Requires the use of a short ground extender on each channel.
	This is the maximum frequency at the minimum swing amplitude. Higher toggle rates can be achieved with higher amplitudes.

Trigger System

Characteristic	Description
Main Trigger Modes	Auto, Normal, and Single
Trigger Coupling	DC, AC, HF reject (attenuates >50 kHz), LF reject (attenuates <50 kHz), noise reject (reduces sensitivity)
Trigger Holdoff Range	20 ns to 8 s

Trigger Sensitivity

Characteristic	Description
Internal DC Coupled
1 MΩ Path (All models)	For 1 mV/div to 4.98 mV/div; 0.75 div from DC to 50 MHz, increasing to 1.3 div at rated bandwidth
50 Ω Path (MSO/DPO4054B, MSO/DPO4034B)	For ≥5 mV/div; 0.4 div from DC to 50 MHz, increasing to 1 div at rated bandwidth
50 Ω Path (MSO/DPO4104B)	0.4 div from DC to 50 MHz, increasing to 1 div at rated bandwidth
External
Auxiliary Input	200 mV from DC to 50 MHz, increasing to 500 mV at rated bandwidth

Trigger Level Range

Characteristic	Description
Any Channel	±8 divisions from center of screen
External (Auxiliary Input)	±8 V

Trigger Modes

Mode	Description
Edge	Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, HF reject, LF reject, and noise reject
Sequence (B-trigger)	Trigger Delay by Time - 4 ns to 8 s. Or Trigger Delay by Events - 1 to 4,000,000 events
Pulse Width	Trigger on width of positive or negative pulses that are >, <, =, or ≠ a specified period of time (4 ns to 8 s)
Timeout	Trigger when no pulse is detected within a specified time (4 ns to 8 s)
Runt	Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again
Logic	Trigger when any logical pattern of channels goes false or stays true for specified period of time (4 ns to 8 s). Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for all analog and digital input channels defined as High, Low, or Don't Care
Setup and Hold	Trigger on violations of both setup time and hold time between clock and data present on any of the input channels
Rise/Fall Time	Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either
Video	Trigger on all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals
Extended Video (Optional)	Trigger on 480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30, 1080p/50, 1080p/60, and custom bi-level and tri-level sync video standards
I²C (Optional)	Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I²C buses up to 10 Mb/s
SPI (Optional)	Trigger on SS active, MOSI, MISO, or MOSI and MISO on SPI buses up to 50 Mb/s
USB (Optional)	Low-speed: Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.Token packet trigger – Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range. Frame number can be specified for SOFToken using binary, hex, unsigned decimal and don't care digits.Data packet trigger – Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.Handshake packet trigger – Any handshake type, ACK, NAK, STALL.Special packet trigger – Any special type, Reserved.Error trigger – PID Check, CRC5 or CRC16, Bit Stuffing.
	Full-speed: Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.Token packet trigger – Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range.Framme number can be specified for SOFToken using binary, hex, unsigned decimal and don't care digits.Data packet trigger – Any data type, DATA0, DATA1; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.Handshake packet trigger – Any handshake type, ACK, NAK, STALL.Special packet trigger – Any special type, PRE, Reserved.Error trigger – PID Check, CRC5 or CRC16, Bit Stuffing.
	High-speed: Trigger on Sync, Reset, Suspend, Resume, End of Packet, Token (Address) Packet, Data Packet, Handshake Packet, Special Packet, Error.Token packet trigger – Any token type, SOF, OUT, IN, SETUP; Address can be specified for Any Token, OUT, IN, and SETUP token types. Address can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular value, or inside or outside of a range.SOF token using binary, hex, unsigned decimal and don't care digits.Data packet trigger – Any data type, DATA0, DATA1, DATA2, DATAM; Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range.Handshake packet trigger – Any handshake type, ACK, NAK, STALL, NYET.Special packet trigger – Any special type, ERR, SPLIT, PING; Reserved. SPLIT packet components that can be specified include:Hub AddressStart/Complete – Don't Care, Start (SSPLIT), Complete (CSPLIT)Port AddressStart and End bits – Don't Care, Control/Bulk/Interrupt (Full-speed Device, Low-speed Device), Isochronous (Data is Middle, Data is End, Data is Start, Data is All)Endpoint Type – Don't Care, Control, Isochronous, Bulk, InterruptError trigger – PID Check, CRC5 or CRC16, Any.
	High-speed support only available on MSO4104B and DPO4104B models.
Ethernet (Optional)	10BASE-T: Trigger on Start Frame Delimiter, MAC Addresses, MAC Q-Tag Control Information, MAC Length/Type, IP Header, TCP Header,TCP/IPv4/MAC Client Data, End of Packet, FCS (CRC) Error.MAC Addresses – Trigger on Source and Destination 48-bit address values.MAC Q-Tag Control Information – Trigger on Q-Tag 32-bit value.MAC Length/Type – Trigger on ≤, <, =, >, ≥, ≠ a particular 16-bit value, or inside or outside of a range.IP Header – Trigger on IP Protocol 8-bit value, Source Address, Destination Address.TCP Header – Trigger on Source Port, Destination Port, Sequence Number, and Ack Number.TCP/IPv4/MAC Client Data – Trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range. Selectable number of bytes to trigger on from 1-16. Byte offset options of Don't Care, 0-1499.
	100BASE-TX: Trigger on Start Frame Delimiter, MAC Addresses, MAC Q-Tag Control Information, MAC Length/Type, IP Header, TCP Header,TCP/IPv4/MAC Client Data, End of Packet, Idle, FCS (CRC) Error.MAC Addresses – Trigger on Source and Destination 48-bit address values.MAC Q-Tag Control Information – Trigger on Q-Tag 32-bit value.MAC Length/Type – Trigger on ≤, <, =, >, ≥, ≠ a particular 16-bit value, or inside or outside of a range.IP Header – Trigger on IP Protocol 8-bit value, Source Address, Destination Address.TCP Header – Trigger on Source Port. Destination Port, Sequence Number, and Ack Number.TCP/IPv4/MAC Client Data – Trigger on ≤, <, =, >, ≥, ≠ a particular data value, or inside or outside of a range. Selectable number of bytes to trigger on from 1-16. Byte offset options of Don't Care, 0-1499.
CAN (Optional)	Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of Frame, Missing ACK, or Bit Stuffing Error on CAN signals up to 1 Mb/s. Data can be further specified to trigger on ≤, <, =, >, ≥, or ≠ a specific data value.User-adjustable sample point is set to 50% by default
LIN (Optional)	Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, Errors such as Sync, Parity, or Checksum Errors up to 100 Kb/s (by LIN definition, 20 Kb/s)
FlexRay (Optional)	Trigger on Start of Frame, Type of Frame (Normal, Payload, Null, Sync, Startup), Identifier, Cycle Count, Complete Header Field, Data, Identifier and Data, End of Frame or Errors such as Header CRC, Trailer CRC, Null Frame, Sync Frame, or Startup Frame Errors up to 100 Mb/s
RS-232/422/485/UART (Optional)	Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, Rx Data, Tx Parity Error, and Rx Parity Error up to 10 Mb/s
MIL-STD-1553 (Optional)	Trigger on Sync, Word Type, Parity Error. Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value, or inside or outside of a range.
I2S/LJ/RJ/TDM (Optional)	Trigger on Word Select, Frame Sync, or Data. Data can be further specified to trigger on ≤, <, =, >, ≥, ≠ a specific data value, or inside or outside of a rangeMaximum data rate for I2S/LJ/RJ is 12.5 Mb/sMaximum data rate for TDM is 25 Mb/s
Parallel (Available on MSO models only)	Trigger on a parallel bus data value. Parallel bus can be from 1 to 20 bits in size. Binary and Hex radices are supported

Acquisition Modes

Mode	Description
Sample	Acquire sampled values
Peak Detect	Captures glitches as narrow as 800 ps (1 GHz models) or 1.6 ns (500 MHz and 350 MHz models) at all sweep speeds
Averaging	From 2 to 512 waveforms included in average
Envelope	Min-Max envelope reflecting Peak Detect data over multiple acquisitions
Hi Res	Real-time boxcar averaging reduces random noise and increases vertical resolution
Roll	Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40 ms/div

Waveform Measurements

Measurement	Description
Cursors	Waveform and Screen
Automatic Measurements	29, of which up to four can be displayed on-screen at any one time. Measurements include: Period, Frequency, Delay, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Peak-to-Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area and Cycle Area
Measurement Statistics	Mean, Min, Max, Standard Deviation
Reference Levels	User-definable reference levels for automatic measurements can be specified in either percent or units
Gating	Isolate the specific occurrence within an acquisition to take measurements on, using either the screen or waveform cursors
Waveform Histogram	A waveform histogram provides an array of data values representing the total number of hits inside of a user-defined region of the display. A waveform histogram is both a visual graph of the hit distribution as well as a numeric array of values that can be measured. Sources – Channel 1, Channel 2, Channel 3, Channel 4, Ref 1, Ref 2, Ref 3, Ref 4, Math Types – Vertical, Horizontal
Waveform Histogram Measurements	Waveform Count, Hits in Box, Peak Hits, Median, Max, Min, Peak-to-Peak, Mean, Standard Deviation, Sigma 1, Sigma 2, Sigma 3

Waveform Math

Characteristic	Description
Arithmetic	Add, subtract, multiply, and divide waveforms
Math Functions	Integrate, Differentiate, FFT
FFT	Spectral magnitude
	FFT Vertical Scale: Linear RMS or dBV RMS
	FFT Window Settings: Rectangular, Hamming, Hanning, Blackman Harris
Advanced Math	Define extensive algebraic expressions including waveforms, reference waveforms, math functions. Perform math on math using complex equations (FFT, Intg, Diff, Log, Exp, Squ, Abs, Sine, Cosine, Tangent, Rad, Deg), scalars, up to two user-adjustable variables and results of parametric measurements (Period, Freq, Delay, Rise, Fall, PosWidth, NegWidth, BurstWidth, Phase, PosDutyCycle, NegDutyCycle, PosOverShoot, NegOverShoot, PeakPeak, Amplitude, RMS, CycleRMS, High, Low, Max, Min, Mean, CycleMean, Area, CycleArea, and trend plots) e.g. (Intg(Ch1-Mean(Ch1))×1.414×VAR1)

Power Measurements (Optional)

Measurement	Description
Power Quality Measurements	VRMS, VCrest Factor, Frequency, IRMS, Icrest Factor, True Power, Apparent Power, Reactive Power, Power Factor, Phase Angle
Switching Loss Measurements	Power Loss: Ton, Toff, Conduction, Total
	Energy Loss: Ton, Toff, Conduction, Total
Harmonics	THD-F, THD-R, RMS measurements
	Graphical and table displays of harmonics
	Test to IEC61000-3-2 Class A and MIL-STD-1399
Ripple Measurements	Vripple and Iripple
Modulation Analysis	Graphical display of +Pulse Width, -Pulse Width, Period, Frequency, +Duty Cycle, and -Duty Cycle modulation types
Safe Operating Area	Graphical display and mask testing of switching device safe operating area measurements
dV/dt and dl/dt Measurements	Cursor measurements of slew rate

Limit/Mask Testing (Optional)

Characteristic	Description
Included Standard Masks	ITU-T, ANSI T1.102, USB
Test Source	Limit Test: Any Ch1 - Ch4 or any R1 - R4 Mask Test: Any Ch1 - Ch4
Mask Creation	Limit test vertical tolerance from 0 to 1 division in 1 m division increments; Limit test horizontal tolerance from 0 to 500 m division in 1 m division increments
	Load standard mask from internal memory
	Load custom mask from text file with up to 8 segments
Mask Scaling	Lock to Source ON (mask automatically re-scales with source-channel settings changes) Lock to Source OFF (mask does not re-scale with source-channel settings changes)
Test Criteria Run Until	Minimum number of waveforms (from 1 to 1,000,000; Infinity) Minimum elapsed time (from 1 second to 48 hours; Infinity)
Violation Threshold	From 1 to 1,000,000
Actions on Test Failure	Stop acquisition, save screen image to file, save waveform to file, print screen image, trigger out pulse, set remote interface SRQ
Actions on Test Complete	Trigger out pulse, set remote interface SRQ
Results Display	Test status, total waveforms, number of violations, violation rate, total tests, failed tests, test failure rate, elapsed time, total hits for each mask segment

Software

Software	Description
NI LabVIEW	A fully interactive measurement software environment optimized for the MSO/DPO4000B Series, enables you to instantly acquire, generate, analyze, compare, import, and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming.
SignalExpress Tektronix Edition	Standard MSO/DPO4000B Series support for acquiring, controlling, viewing, and exporting your live signal data is permanently available through the software. The full version (SIGEXPTE) adds additional signal processing, advanced analysis, mixed signal, sweeping, limit testing, and user-defined step capabilities and is available for a 30-day trial period standard with each instrument.
OpenChoice® Desktop	Enables fast and easy communication between a Windows PC and the MSO/DPO4000B Series, using USB or LAN. Transfer and save settings, waveforms, measurements, and screen images. Included Word and Excel toolbars automate the transfer of acquisition data and screen images from the oscilloscope into Word and Excel for quick reporting or further analysis.
IVI Driver	Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI, Microsoft .NET and MATLAB.
e*Scope®	Enables control of the MSO/DPO4000B Series over a network connection through a standard web browser. Simply enter the IP address or network name of the oscilloscope followed by :81 (to represent connecting through Port 81) and a web page will be served to the browser
LXI Class C Web Interface	Connect to the MSO/DPO4000B Series through a standard web browser by simply entering the oscilloscope's IP address or network name in the address bar of the browser. The web interface enables viewing of instrument status and configuration, and status and modification of network settings. All web interaction conforms to LXI Class C specification.

Display Characteristics

Characteristic	Description
Display Type	10.4 in. (264 mm) liquid-crystal TFT color display
Display Resolution	1,024 horizontal × 768 vertical pixels (XGA)
Waveform Styles	Vectors, Dots, Variable Persistence, Infinite Persistence
Graticules	Full, Grid, Solid, Cross Hair, Frame, IRE, and mV
Format	YT and simultaneous XY/YT
Waveform Capture Rate	>50,000 wfm/s maximum

Input/Output Ports

Port	Description
USB 2.0 High-speed Host Port	Supports USB mass storage devices, printers and keyboard. Two ports on front and two ports on rear of instrument
USB 2.0 Device Port	Rear-panel connector allows for communication/control of oscilloscope through USBTMC or GPIB (with a TEK-USB-488), and direct printing to all PictBridge-compatible printers
LAN Port	RJ-45 connector, supports 10/100/1000 Mb/s
XGA Video Port	DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector
Auxiliary Input	Front-panel BNC connector. Input Impedance 1 MΩ. Max input 300 VRMS CAT II with peaks ≤ ±425 V
Probe Compensator Output	Front-panel pins Amplitude: 2.5 V Frequency: 1 kHz
Auxiliary Out	Rear-panel BNC connector VOUT(Hi): ≥2.5 V open circuit, ≥1.0 V 50 Ω to ground VOUT(Lo): ≤0.7 V into a load of ≤4 mA; ≤0.25 V 50 Ω to ground Output can be configured to provide a pulse out signal when the oscilloscope triggers, the internal oscilloscope reference clock out, or an event out for limit/mask testing
External Reference In	Time-base system can phase lock to an external 10 MHz reference (10 MHz ±1%)
Kensington Lock	Rear-panel security slot connects to standard Kensington lock

LAN eXtensions for Instrumentation (LXI)

Characteristic	Description
Class	LXI Class C
Version	V1.3

Power Source

Characteristic	Description
Power Source Voltage	100 to 240 V ±10%
Power Source Frequency	45 to 66 Hz (85 to 264 V) 360 to 440 Hz (100 to 132 V)
Power Consumption	225 W maximum

Physical Characteristics

Dimensions	mm	in.
Height	229	9.0
Width	439	17.3
Depth	147	5.8
Weight	kg	lb.
Net	5	11
Shipping	10.7	23.6
Rackmount Configuration	5U
Cooling Clearance	2 in. (51 mm) required on left side and rear of instrument
VESA Mount	Standard (MIS-D 100) 100 mm VESA mounting points on rear of instrument

Environmental

Characteristic	Description
Temperature
Operating	0 °C to +50 °C
Nonoperating	-20 °C to +60 °C
Humidity
Operating	High: 40 °C to 50 °C, 10% to 60% Relative Humidity Low: 0 °C to 40 °C, 10% to 90% Relative Humidity
Nonoperating	High: 40 °C to 60 °C, 5% to 60% Relative Humidity Low: 0 °C to 40 °C, 5% to 90% Relative Humidity
Altitude
Operating	9,843 ft. (3,000 m)
Nonoperating	30,000 ft. (9,144 m)
Regulatory
Electromagnetic Compatibility	EC Council Directive 2004/108/EC
Safety	UL61010-1, Second Edition; CSA61010-1 Second Edition, EN61010-1:2001; IEC 61010-1:2001

Ordering Information

MSO/DPO4000B Family

Model	Description
DPO4000B Models
DPO4034B	350 MHz, 2.5 GS/s, 20M record length, 4-channel digital phosphor oscilloscope
DPO4054B	500 MHz, 2.5 GS/s, 20M record length, 4-channel digital phosphor oscilloscope
DPO4104B	1 GHz, 5 GS/s, 20M record length, 4-channel digital phosphor oscilloscope
MSO4000B Models
MSO4034B	350 MHz, 2.5 GS/s, 20M record length, 4+16 channel mixed signal oscilloscope
MSO4054B	500 MHz, 2.5 GS/s, 20M record length, 4+16 channel mixed signal oscilloscope
MSO4104B	1 GHz, 5 GS/s, 20M record length, 4+16 channel mixed signal oscilloscope

All Models Include: One passive voltage probe per analog channel (TPP0500 500 MHz, 10X, 3.9 pF for 500 MHz and 350 MHz models; TPP1000 1 GHz, 10X, 3.9 pF for 1 GHz models), Front Cover (200-5130-xx), User Manual (071-2810-xx), Documentation CD (063-4300-xx), OpenChoice® Desktop Software, NI LabVIEW SignalExpress™ Tektronix Edition Software, Calibration Certificates document measurement traceability to National Metrology Institute(s) – the Quality System this product is manufactured in is ISO9001 registered, power cord, accessory bag (016-2029-xx) and a three-year warranty. Please specify power plug and manual language version when ordering.

MSO Models also Include: One P6616 16-channel logic probe and a logic probe accessory kit (020-2662-xx).

Application Modules

Module	Description
DPO4AERO	Aerospace Serial Triggering and Analysis Module. Enables triggering on packet-level information on MIL-STD-1553 buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information. Signal Inputs – Any Ch1 - Ch4 (and any D0 - D15 on MSO models) Recommended Probing – Single ended
DPO4AUDIO	Audio Serial Triggering and Analysis Module. Enables triggering on packet-level information on I2S, LJ, RJ, and TDM audio buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information. Signal Inputs – Any Ch1 - Ch4 (and any D0 - D15 on MSO models) Recommended Probing – I2S, LJ, RJ, TDM: Single ended
DPO4AUTO	Automotive Serial Triggering and Analysis Module. Enables triggering on packet-level information on CAN and LIN buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information. Signal Inputs – LIN: Any Ch1 - Ch4 (and any D0 - D15 on MSO models); CAN: Any Ch1 - Ch4 (and any D0 - D15 on MSO models), single-ended probing only Recommended Probing – LIN: Single ended; CAN: Single ended or differential
DPO4AUTOMAX	Extended Automotive Serial Triggering and Analysis Module. Enables triggering on packet-level information on CAN, LIN, and FlexRay buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, packet decode tables with time-stamp information, and eye diagram analysis software. Signal Inputs – LIN: Any Ch1 - Ch4 (and any D0 - D15 on MSO models); CAN: Any Ch1 - Ch4 (and any D0 - D15 on MSO models), single-ended probing only; FlexRay: Any Ch1 - Ch4 (and any D0 - D15 on MSO models), single-ended probing only Recommended Probing – LIN: Single ended; CAN, FlexRay: Single ended or differential
DPO4COMP	Computer Serial Triggering and Analysis Module. Enables triggering on packet-level information on RS-232/422/485/JUART buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information. Signal Inputs – Any Ch1 - Ch4 (and any D0 - D15 on MSO models), single-ended probing only Recommended Probing – RS-232/JUART: Single ended; RS-422/485: Differential

Module Description

DPO4EMBD	Embedded Serial Triggering and Analysis Module. Enables triggering on packet-level information on I2C and SPI buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information. Signal Inputs - I2C: Any Ch1 - Ch4 (and any D0 - D15 on MSO models); SPI: Any Ch1 - Ch4 (and any D0 - D15 on MSO models) Recommended Probing - I2C, SPI: Single ended
DPO4ENET	Ethernet Serial Triggering and Analysis Module. Enables triggering on packet-level information on 10BASE-T and 100BASE-TX buses as well as analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information. Signal Inputs - Any Ch1 - Ch4 Recommended Probing - 10BASE-T: Single ended or differential; 100BASE-TX: Differential
DPO4USB	USB Serial Triggering and Analysis Module. Enables triggering on packet-level content for low-speed, full-speed, and high-speed USB serial buses. Also enables analytical tools such as digital views of the signal, bus views, packet decoding, search tools, and packet decode tables with time-stamp information for low-speed, full-speed, and high-speed USB serial buses. Signal Inputs - Low-speed and Full-speed: Any Ch1 - Ch4 (and any D0 - D15 on MSO models) for single ended, Any Ch1 - Ch4 for differential; High-speed: Any Ch1 - Ch4 Recommended Probing - Low-speed and Full-speed: Single ended or differential; High-speed: Differential USB high-speed supported only on MSO4104B and DPO4104B models
DPO4PWR	Power Analysis Application Module. Enables quick and accurate analysis of power quality, switching loss, harmonics, safe operating area (SOA), modulation, ripple, and slew rate (dI/dt, dV/dt)
DPO4LMT	Limit and Mask Testing Application Module. Enables testing against limit templates generated from "golden" waveforms and mask testing using custom or standard telecommunications or computer masks
DPO4VID	HDTV and Custom (nonstandard) Video Triggering Module

Instrument Options

Power Plug Options

Option	Description
Opt. A0	North America
Opt. A1	Universal Euro
Opt. A2	United Kingdom
Opt. A3	Australia
Opt. A5	Switzerland
Opt. A6	Japan
Opt. A10	China
Opt. A11	India
Opt. A99	No power cord or AC adapter

Language Options*1

Option	Description
Opt. L0	English manual
Opt. L1	French manual
Opt. L2	Italian manual
Opt. L3	German manual
Opt. L4	Spanish manual
Opt. L5	Japanese manual
Opt. L6	Portuguese manual
Opt. L7	Simplified Chinese manual
Opt. L8	Traditional Chinese manual
Opt. L9	Korean manual
Opt. L10	Russian manual
Opt. L99	No manual

*1 Language options include a translated front-panel overlay for the selected language(s).

Service Options*2

Option	Description
Opt. CA1	Provides a single calibration event, or coverage for the designated calibration interval, whichever comes first.
Opt. C3	Calibration Service 3 years
Opt. C5	Calibration Service 5 years
Opt. D1	Calibration Data Report
Opt. D3	Calibration Data Report 3 years (with Opt. C3)
Opt. D5	Calibration Data Report 5 Years (with Opt. C5)
Opt. R5	Repair Service 5 years (including warranty)

*2 Probes and accessories are not covered by the oscilloscope warranty and service offerings. Refer to the datasheet of each probe and accessory model for its unique warranty and calibration terms.

Recommended Probes

Tektronix offers over 100 different probes to meet your application needs. For a comprehensive listing of available probes, please visit wwwTektronix.com/probes.

Probe	Description
TPP0500	500 MHz, 10X TekVPI® passive voltage probe with 3.9 pF input capacitance
TPP1000	1 GHz, 10X TekVPI passive voltage probe with 3.9 pF input capacitance
TAP1500	1.5 GHz TekVPI active single-ended voltage probe
TDP1500	1.5 GHz TekVPI differential voltage probe with ±25 V differential input voltage
TDP1000	1 GHz TekVPI differential voltage probe with ±42 V differential input voltage
TDP0500	500 MHz TekVPI differential voltage probe with ±42 V differential input voltage
TCP0150	20 MHz TekVPI 150 Ampere AC/DC current probe
TCP0030	120 MHz TekVPI 30 Ampere AC/DC current probe
P5200	1.3 kV, 25 MHz high-voltage differential probe
P5205*3	1.3 kV, 100 MHz high-voltage differential probe
P5210*3	5.6 kV, 50 MHz high-voltage differential probe
P5100	2.5 kV, 100X high-voltage passive probe

*3 Requires TekVPI® to TekProbe BNC adapter (TPA-BNC).

Recommended Accessories

Accessory	Description
077-0512-xx	Service Manual (English only)
SIGEXPTE	NI LabVIEW SignalExpress™ Tektronix Edition Software (Full Version)
FPGAView-xx	MSO Support for Altera and Xilinx FPGAs
TPA-BNC	TekVPI-to-TekProbe BNC Adapter
TEK-USB-488	GPIB-to-USB Adapter
ACD4000B	Soft Transit Case
HCTEK54	Hard Transit Case (Requires ACD4000B)
RMD5000	Rackmount Kit
TEK-DPG	Deskew Pulse Generator
067-1686-xx	Deskew Fixture

Warranty

Three-year warranty covering all parts and labor, excluding probes.

C

Product(s) are manufactured in ISO registered facilities.

Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.

For Further Information

Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit www.tektronix.com

Copyright © 2010, Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks or registered trademarks of their respective companies.

20 Oct 2010

3GF-20156-9