NEUTRON - Guillotine FELLOWES - Free user manual and instructions

USER MANUAL NEUTRON FELLOWES

Number Cutting Cutting | Cutting capacity Number Cutting Cutting | Cutting capacity CRC# | Model of blades | Length (mm) | Length (inch) | (sheets 20 Ib) CRC# | Model of blades | Length (mm) [Length (inch) | (sheets 20 Ib) 54100 | Neutron 1 320 12 10 54104 | Electron 120 4 320 12 10 54101 | Neutron Plus 4 320 12 10 54105 | Electron 180 4 460 18 10 54102 | Proton 120 L 320 12 10 54103 | Proton 180 L 460 18 10 IMPORTANT SAFETY INSTRUCTIONS — Read Before Using! Electron! SET-UP ACAUTION To operate: « Caution: blades are extremely sharp. 1. Remove battery and cover e SafeCut" cassette encloses blades — do not try to extract blades manually. 2. Remove plastic film © Always supervise children during use. 3. Re-insert battery and cover + Do not overload timmer. © Keep pets away from timmer while in use. < Do not open or attempt to repaïr, as this will void your warranty. Contact Customer Service if you have questions. Please note the warranty does not apply in cases of abuse, mishandling or unauthorized repair. «Do not try to open SafeCut" blade cartridges.

CUTTING PAPER AND PHOTOS

1. Slide cutting carriage to one 2. Place item (e.g. photo or 3. Hold paper steady with hand or 4. To cut, push handle downwards and end into lock position. paper) onto cutting table. damping mechanism. To activate slide carriage along until reaching cutting blade, push down carriage the end of the bar. At the end of the handle. (Electron: when pressing bar, release the carriage and the handle down, LED will glow) damping mechanism will release. For cutting larger capacities press blade harder on side nearest the cutting strip.

1. Slide cutting carriage to one 2. Lift carriage handle up. 3. Pull SafeCut'" cartridge 4. Press yellow button to release end into lock position. upwards out of cutting carriage cassette from base. Return and insert new cartridge (push into storage slot in base. down to dick into place).

CHANGING CUTTING STRIP

1. Slide cutting carriage to one 2. Remove cutting strip off 3. Turn cuting strip over to use 4. Replacement strips available end into lock position. trimmer base. both sides. (see accessory details).

1. Slide cutting carriage to one end

into lock position. Pull (swing) carriage handle up. CHANGE BATTERY ON ELECTRON SAFECUT"" LED GUIDE

2. Turn switch to ON (1) position.

3. Pull (swing) carriage handle down. 4. Press handle down to activate

SafeCut'M LED Guide.

1. Slide cutting carriage to one end

into lock position. Pull (swing) carriage handle up. WARRANTY Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 2 year from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exdusive remedy will be repair or replacement, at Fellowes” option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY

2. Unscrew battery cover with coin

or screwdriver (left turn opens, right turn closes battery cover).

3. Remove old battery and replace

with a new battery [type CR2032].

4. Close battery cover.

LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attrbutable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer. Accessories and consumables are excluded from this warranty. Need Help? Customer Service. uv fellowes. com Let our experts help you with a solution. Alrays cal Fellowes before contacting your place of purchase