Bongo Doble Y85 2x2 Xxl Connected - Scooter CECOTEC - Free user manual and instructions

USER MANUAL Bongo Doble Y85 2x2 Xxl Connected CECOTEC

bongo

1. Warnings 72
2. Parts and components 74
3. Before use 75
4. Assembling the appliance 76
5. Operation 77
6. Cleaning and maintenance 78
7. Troubleshooting 80
8. Technical specifications 80
9. Disposal of old electrical and electronic appliances 82
10. Technical support and warranty 82
11. Copyright 83

SOMMAIRE

EN · The coding in this manual is generic and applies to all code variants of the appliance.

Read these instructions thoroughly before using the appliance. Keep this instruction manual for future reference or new users.

- Cecotec shall not be liable for any problem caused by misuse of the appliance or non-compliance of both the traffic regulations and the instructions in this manual.

- This electric scooter is an entertainment appliance. However, in some jurisdictions, it is allowed to be used on public roads. Make sure you comply with the local traffic regulations when using the electric scooter in these situations, as it will be considered a vehicle. Ride in a civilised manner and pay attention to people and obstacles around you to prevent accidents.

- Remember that, if you follow the instructions and warnings in this instruction manual, as well as the traffic regulations in your area, you will reduce risks, but you will not completely prevent them.

- Bear in mind that the higher the speed, the greater the braking distance. Remember that hard braking can cause slips and falls.

- Keep a safe distance with other people and vehicles. Respect pedestrians and give them way whenever possible. When you come closer to a pedestrian, reduce the speed and stay on the right side. Avoid frightening or surprising pedestrians. Overtake other vehicles on the left whenever possible (applicable to countries where vehicles drive on the right).

- Wear protective equipment, like a helmet and elbow/knee pads to avoid or reduce injuries in case of accidents or falls. You must use footwear.

- We recommend you practice with the electric scooter before riding it in public areas.

• Make sure both you and the people using the electric scooter read and understand these instructions completely. Do not allow anyone to use the electric scooter if they aren't familiar with how it works.
• Avoid jumping over obstacles such as kerbs, steps, or manholes with the electric scooter. Match the speed and trajectory to those of a pedestrian to cross these obstacles. It is recommended to get off the electric scooter when these obstacles become dangerous due to their height, shape, or slipperiness.
• Make sure the wheels are not damaged and all parts and components of the electric scooter are correctly installed before each use. If you notice any of the parts is loose, hear strange noises, or the electric scooter does not work correctly, stop using it immediately and contact the official Cecotec Technical Support Service.
• Do not use the electric scooter in a manner that could damage other objects or injure other people.
• It is not allowed to modify the electric scooter in any manner, as this could alter its performance or damage its structure and cause damage or injury. Do not use any accessories or parts not approved by the manufacturer. Do not modify or tamper with the electric scooter, including the steering tube and sleeve, power, folding mechanism, and/or braking system. Any unauthorised change will void the appliance warranty.
• To prevent the electric scooter from being damaged or causing an accident, do not use it under the rain.

• The electric scooter must not be used by children from 0 to 16 years old. It can be used by children over the age of 16, as long as they are given continuous supervision. Check the current local regulations.

• This appliance can be used by children aged 16 and above, and people with reduced physical, sensory, or mental capabilities or lack of experience and knowledge, as long as they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Do not allow children to play with the appliance.

• Supervise children to prevent them from playing with the appliance. Close supervision is necessary when the electric scooter is being used by or near children.
• Do not modify the braking system to avoid affecting the safety of the device.
• Make sure that the mains voltage matches the voltage stated on the device marking and that the wall outlet is earthed before charging the device.
• Check the charger cable and casing regularly for visible damage. Do not use the electric scooter if the charger cable, socket, or structure are damaged, do not work properly, or have fallen, and contact the the official Cecotec Technical Support Service immediately. If the power cable is damaged, it must be replaced with a special cable or set to be supplied by the official Cecotec Technical Support Service. The power cable is to be properly discarded.
• When you wish to disconnect the charger, pull from the plug, never the cable. Do not handle the plug or the electric scooter with wet hands.
• Remember that changing wheels is a complicated process, and it is advisable to let authorised personnel or the official Cecotec Technical Support Service take care of it. Damages caused by misuse will void the guarantee.

• Check wheel pressure before every use. Remember that a low pressure may reduce the battery life.

• Use this electric scooter only with the power supply provided and with original Cecotec batteries compatible with this model.

• WARNING: to recharge the battery, only use the power supply unit provided with the appliance, reference HLT-180-5462000.
• We recommend you charge the battery after every use and before it completely runs out of battery.
• WARNING! Keep plastic packaging out of the reach of children to prevent suffocation.

Battery safety instructions

• This electric scooter includes a lithium-ion battery.
• Unplug the battery from the charger before riding the electric scooter and before folding or unfolding it.
• Charge the battery at a room temperature between 0 °C and 35 °C to ensure efficient operation of the electric scooter.
• Do not burn or expose batteries to high temperatures, as they may explode.
• The battery may leak under extreme conditions. Do not touch any liquid that leaks from the battery. If the liquid gets into contact with skin, wash immediately with soap and water. If the liquid gets into the eyes, wash them immediately with clean water for a minimum of 10 minutes and seek medical attention. Wear gloves to handle the battery and dispose of it immediately in accordance with local regulations.
• Avoid contact between the battery and small metallic objects such as paper clips, coins, keys, nails, or screws.
• Never modify the charger in any way.
• The battery must be removed from the device for safe disposal.
• Battery ingestion can cause burns, perforation of soft tissue,

and death. It can cause severe burns within two hours of the ingestion.

• In case of battery ingestion, please seek medical help immediately.
• Non-rechargeable batteries must not be recharged.
• The battery supply terminals must not be short-circuited.
• If the device is stored for a long period of time, you should remove the battery.
• The battery must be inserted in the correct position. When replacing batteries, check the polarity.

INSTRUCTIONS DE SÉCURITÉ

ADVERTENCIA:

You must read and follow the safety instructions in this manual before riding the electric scooter. Use approved safety equipment such as helmets or knee pads. This appliance is intended for use as a personal mobility vehicle for the purpose of transporting a single person in a public or private place.

Fig. 2

Do not use the vehicle in the rain.

Fig. 3

The electric scooter cannot be used by more than one person at a time.

Fig. 4

This appliance cannot be used by children under 16. Check the current local regulations. Strictly consider your health and body condition. You should consult your doctor to determine if you have any physical or health conditions that could create a risk to your safety or prevent you from using the electric scooter properly.

Fig. 5.

Maximum weight allowed: 120 kg.

Recommended maximum user height: up to 2 metres.

Fig. 6.

Do not ride the electric scooter under the influence of alcoholic drinks, drugs, or medicine whose consumption is not compatible with riding.

Fig. 7

Do not use the phone or listen to music while riding the electric scooter.

Fig. 8

Pay special attention when riding when there is sand, puddles, mud, ice, snow, or stairs and when it is dark, or the floor is wet. Do not touch the disc brake in poor lighting conditions or after use, as it may still be hot.

Fig. 9

Do not use the electric scooter in hazardous areas where there could be flammable or explosive substances, liquids, or dirt.

Fig. 10

This electric scooter is not designed to be ridden on motorways, highways, or intercity roads. Check the current legislation of your local authority on where electric scooters are allowed to be ridden.

Fig. 11

Do not place heavy objects on the handlebar. Any load attached to the handlebar will affect the stability of the vehicle.

Fig. 12

Avoid climbing up and down the stairs with the electric scooter.

Fig. 13

Always ride with both hands on the handlebar.

Fig. 14

Do not ride the electric scooter with just one foot.

Fig. 15

Do not turn the throttle when walking along with the electric scooter.

Fig. 16

Note that the braking distance will be longer in puddles, wet surfaces, and/or in wet-weather conditions. The electric scooter is intended for use on flat, level, and dry surfaces.

Fig. 17

Watch your head when riding under roofed areas, like a door.

Fig. 18

When riding at high speed, do not turn the handlebar abruptly.

Fig. 19

Do not ride at high speed over obstacles like steps, kerbs, or speed bumps.

Fig. 20

Do not hit obstacles with the wheels.

Fig. 21

Do not touch the motor immediately after riding, it may be at high temperature.

ENGLISH

WARNING!

• Regularly check the condition of components or parts subject to wear or fatigue, such as the main frame, fork, wheels, brakes, etc. This will allow you to detect cracks or damage in high-stress areas that may indicate the component's service life has been exceeded and it needs to be replaced. Regular maintenance of the electric scooter and its components will extend its service life. Periodically check the tightness of the bolted parts, especially the wheel axles, the folding mechanism, the steering system, and the braking system.
• Contact the retailer to be referred to an appropriate training organisation.
• Avoid high traffic or overcrowded areas and anticipate your path and speed by respecting the traffic code and watching out for pedestrians on pavements.
• Make sure pedestrians/cyclists are aware of your nearby presence upon approach when you are not seen and/or heard. Remember to cross protected areas on foot and in all situations take care of yourself and others. Remove any sharp edges that may have been caused by the use of the vehicle.
• Use the vehicle only for its intended purpose. This vehicle is not designed for stunt use.

2. PARTS AND COMPONENTS

Fig. 22

1. Headlight
2. Folding mechanism
3. Front folding bar
4. Front shock absorber
5. Front fender
6. Front disc brake
7. Front wheel
8. Right-hand grip
9. Left-hand grip
10. Hook
11. Stem
12. Anti-slip platform
13. Deck
14. Charging port
15. Hook ring
16. Taillight
17. Rear shock absorber
18. Rear disc brake
19. Rear fork
20. Motor

21. Decorative light

22. Kickstand (Parking device)

23. Front fork

Fig. 23

1. Brake lever
2. Left-hand grip
3. Display
4. Brake lever
5. Right-hand grip
6. Power/Light button
7. Throttle
8. Riding mode selector/Speed unit

Fig. 24

1. Speed units miles per hours (mph)
2. Cruise mode indicator light
3. Headlight indicator light
4. Eco mode indicator light
5. SDS mode indicator light
6. Sport mode indicator light
7. Pedestrian mode indicator light
8. Speed units kilometres per hour (km/h)
9. Error code indicator light
10. Battery level indicator light

NOTE:

the graphics in this manual are schematic representations and may not exactly match the device.

3. BEFORE USE

This electric scooter comes in a packaging designed to protect it during transport. Take the electric scooter out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the appliance when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.

Make sure all parts and components are included and in good conditions. If there is any piece missing or not in good condition, contact the official Cecotec Technical Support Service immediately.

ENGLISH

Box content

Fig. 25

1. Electric scooter
2. Adapter
3. Tools required for assembly
4. Instruction manual

4. ASSEMBLING THE APPLIANCE

Assembly

1. Fold out the handlebar, lock it and lower the kickstand.
2. Connect the wires protruding from the handlebars to their corresponding connector on the stem.
3. Install the handlebar on the stem.
4. Tighten the screws on both sides of the stem with the T-shaped Allen key.
5. After assembly, press the power button to check for proper operation.

Folding mechanism. Fig. 26

1. Release the safety lock.
2. Pull the lever all the way down to its maximum lower position.
3. Pull the stem backwards.
4. Attach the hook to the hook ring to fold the scooter.

Charging the electric scooter

1. Make sure the electric scooter is switched off before and during charging.
2. Connect the charger to the electric scooter's charging port and connect the charging plug to a power outlet.
3. Charge the electric scooter for at least 8 hours before first use.
4. The charger indicator light will light up green when 100% charge is reached.
5. Never use the electric scooter while it is charging.
6. Do not charge the electric scooter for longer than necessary.
7. To maximise battery life, charge the battery at least every three months.
8. Be sure to charge the electric scooter in a dry and clean environment. The input voltage is 100–240 V. Connect the charging cable securely to the charging port of the electric scooter.

Note

Stop charging the battery when the indicator light colour changes to green. Do not exceed the battery charging time so as not to affect its shelf life.

WARNING!

Cover the charging port with the dirt cap to prevent any metallic object from coming into contact with it and to avoid short circuits.

If the voltage is below 44.8 V, the undervoltage alarm will be activated, and the battery indicator will flash on the display. If the voltage is below 32.5 V, it will enter in undervoltage protection mode, and the battery indicator will flash on the display.

5. OPERATION

1. Switching the scooter on/off

Press and hold the power/light button to turn the scooter on or off. After 10 minutes of inactivity, the electric scooter will automatically switch off.

2. Switching the lights on/off

• Press the power/light button once to turn the headlight and taillight on or off.
• Press the power button twice in succession to switch the decorative light on or off.

3. Riding modes

Press the riding mode selector/speed unit button to select between the different modes:

• Pedestrian mode: in this mode, the scooter can reach 6 km/h (3 mph).
• Eco mode: in this mode, the scooter can reach 15 km/h (9 mph).
• SDS mode: in this mode, the scooter can reach 25 km/h (15 mph). This mode detects the slope of the road and provides the appropriate power and acceleration at any given moment for better battery management. For a more personalised result, you can enter the user's weight via the app, so that the system can take this into account when calculating the required power.
• *This calculation is made considering that the tyre pressure is that recommended by the manufacturer.

• Sport mode: in this mode, the scooter can reach 25 km/h (15 mph).

• Press the power button 3 times in succession to change the unit of speed (km/h or mph).

• Press the power button 5 times in succession to activate/deactivate the cruise control.

Tyre use

• For a correct operation of the electric scooter, you should check and ensure the correct pressure on the wheels before every use.
• The optimum pressure for these tyres is de 36 PSI / 2.5 bars / 250 kPa.
• We recommend you carry out periodic checks to ensure the pressure is within the recommended values to achieve efficient operation.

ENGLISH

- During the shelf life of the wheels, we recommend using heat-sealing gels to prevent punctures and maintain maximum effectiveness and performance.

Operation of parking and braking devices

• Braking device: the electric scooter is equipped with a braking system that consists of an electric brake and a disc brake. To stop the electric scooter, actuate the brake lever on the handlebars. Make sure to get familiar with the location and operation of the brake before using the electric scooter. The location of these components can be found in section 2. "Parts and components."
• Parking device: the electric scooter is equipped with a parking device which allows the scooter to be kept in a stable position when not in use. The location of this device can be found in section 2. "Parts and components."

Note: the parking device must always be activated when the vehicle is not in use.

This is crucial to prevent accidental falls and to ensure safety.

Pairing

By scanning the following QR code you will be able to access the app download option and an instruction manual explaining how to pair your appliance:

WARNING:

It is not permitted, by the user, to make any changes or modifications to any component of the electric scooter. If any modifications are made, the warranty will be void. It is only allowed to change the tyre for a tyre with the same characteristics, if a change of tyre with different characteristics than the original one is made, the appliance warranty will be lost.

6. CLEANING AND MAINTENANCE

Maintenance

1. Battery maintenance: to extend the lifespan of the battery, recharge the scooter only when the battery is about to run out. (Note: if you do not plan to use the scooter for a long period of time, it is recommended to recharge the battery at least once a month). If you need to replace the battery, refer to qualified professionals.

2. Undervoltage protection: when the battery voltage falls below the set undervoltage value, the controller enters the undervoltage protection state. The motor will stop working to protect the lifespan of the battery.

3. Voltage limit protection:

The maximum output (voltage) of the controller is limited to 25 ± 1A to protect the battery, controller and motor, etc.

1. Wheel maintenance: to ensure the lifespan of the wheels, check them regularly. If the wheel does not function properly, repair or replace it as soon as possible to prevent further damage to the scooter.

2. Maintenance of the main body: clean the electric scooter body with water or mild detergent. Do not use strong cleaning agents, solvents or chemicals to clean the main body of the scooter.

3. Make sure the device is not plugged to the power supply or switched on before cleaning or maintenance.

4. Use a soft cloth to clean the exterior housing of the electric scooter.
5. Never use alcohol, petrol, paraffin, corrosive, or abrasive products to clean the electric scooter.
6. Never immerse the electric scooter in water or any other liquid to clean it, as this could damage the electronic parts permanently.
7. Never use pressurised water to clean the electric scooter.
8. Do not try to repair the electric scooter on your own. Should it not work correctly or be damaged, please contact the official Cecotec Technical Support Service.
9. Self-tapping nuts and other fasteners may loosen their hold and need to be retightened.
10. If the scooter is expected to be inactive for more than 30 days, fully charge the battery and place it in a cool, dry place. Remember to recharge it every 60 days to protect the battery from possible damage beyond the scope of the warranty.
11. Disassembly of the wheels is complicated and improper assembly can cause instability and malfunction.

Disc brake

You must check the disc brake is in perfect condition, matching the brake calliper: fix this easily with the Allen key provided. Brake pads are consumable parts and must be replaced when their shelf life expires.

Storage

• When not in use, store the scooter in a dry and ventilated place. Do not leave it outdoors for a long time. Excessive sunlight, overheating, and overcooling accelerate tyre ageing and compromise the service life of the scooter and its battery.
• Charge it only if the room temperature is between 0 °C and 40 °C and store it at a temperature between -10 °C and 45 °C.

ENGLISH

Battery removal

• Removing the battery is complicated and may alter the operation of the electric scooter: you can contact an authorised repair entity if the warranty is still valid. If the warranty has expired, you can contact a specialist workshop of your choice. You can also contact the official Cecotec Technical Support Service.

• For proper removal of the battery for subsequent recycling, you must:

• Step 1: remove the anti-slip silicone rubber from the cover.

• Step 2: unscrew all screws (10 pieces in total) to open the battery chassis.
• Step 3: open the battery chassis cover, and remove the battery holder, to release the battery.
• Step 4: disconnect the two connectors (one is the battery connection to the controller; the other is the battery connection to the charging port).
• Step 5: then you can remove the battery from the battery chassis.

7. TROUBLESHOOTING

Error code

• EO: communication failure.
• E1: motor failure.
• E2: accelerator failure.
• E3: brake failure.
• E4: MOS failure or overcurrent failure.
• E5: signal failure.
• E6: rotation failure.
• E7: undervoltage.
• E8: overvoltage.
• E9: overheating.

8. TECHNICAL SPECIFICATIONS

Model:	Bongo Doble Y85 2X2 XXL Connected Electric scooter
Reference:	09280
Features	Measuring units	Specifications
Dimensions	Folding	121 x 60 x 58 cm
	Unfolded (1)	121 x 130 x 58 cm
Weight	Electric scooter weight	35 kg
User requirements	Max. weight	120 kg
	Min-max height	100 - 200 cm
	Age range (2)	>16 years old
Technical specifications	Range (3)	85 km
	Max. speed	25 km/h
	Max. inclination	15%
	Operating temperature	0 °C | 40 °C
	Storage temperature	0 °C | 45 °C
	IP protection rating	IPX4
Motor	Max. power	2 x 1050 W
	Rated power	2 x 500 W
Battery	Type	JT Tech Jt-esb12-07
	Charging time	5-6 hrs
	Capacity	18.2 Ah
	Rated voltage	48 V
	Max. charge voltage	54.6 V
	Max. charging current	2 A
Wheels	Wheel	10"
Charger	Model	HLT-180-5462000
	Input	100-140 V 50/60 Hz 2 A
	Outlet	54.6 V DC, 2 A
	Protection	IP20; T=0 - 40 °C; Class II

ENGLISH

Riding modes andautonomies (4)	PEDESTRIAN	100 km
	ECO	85 km
	SDS	75 km
	SPORT	50 km

(1) Height from the floor to the upper part of the handlebar.
(2) Check the current local regulations.
(3) Range measured with a weight of 80 kg, fully charged battery, in ECO mode on a flat surface, without wind, and with an ambient temperature of approx. 25 °C.
(4) It has been measured with an 80 kg weight, completely charged battery, flat surface, no wind, and a room temperature of approximately 25\ °C .
The total value of the exposed vibration in the hand-arm system does not exceed 2.5 m/s² . The weighted acceleration to which the whole body is submitted does not exceed 0.5 m/s² . The A-weighted emission sound pressure level at work stations is less than or equal to 70 dB.

Technical specifications may change without prior notification to improve product quality.

Made in China | Designed in Spain

9. DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

Compliance with the above guidelines will help protecting the environment.

10. TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions and deadlines established by the applicable regulations.

Repairs should be carried out by qualified personnel.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at [phone].

11. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

FRANÇAIS

1. AVERTISSEMENTS

Img. 1

AVERTISSEMENT :

DEUTSCH

WARNUNG:

ATTENZIONE:

2. Ligar/desligar as luzes:

ADVERTÊNCIA:

4. HET APPARAAT MONTEREN

Montage

WAARSCHUWING:

7. PROBLEEMOPLOSSING

Foutcode

• EO: communicatiestoring.
• E1: motorstoring.
• E2: storing in de gashendel.
• E3; storing in de rem.
• E4: MOS-fout of overstroomfout.
• E5: signaalstoring.
• E6: rotatiefout.
• E7: onderspanning.
• E8: overspanning.

• E9: oververhitting.

• TECHNISCHE SPECIFICATIES

OSTRZEŻENIE:

VAROVÁNÍ:

DİKKAT:

ΠΡΟΕΙΔΟΠΟΙΗΣΗ:

Fig./Img./Abb./Afb./Rys.1

Fig./Img./Abb./Afb./Rys. 2

Fig./Img./Abb./Afb./Rys. 3

Fig./Img./Abb./Afb./Rys. 4

Fig./Img./Abb./Afb./Rys. 5

Fig./Img./Abb./Afb./Rys. 6

Fig./Img./Abb./Afb./Rys. 7

Fig./Img./Abb./Afb./Rys. 8

Fig./Img./Abb./Afb./Rys. 9

Fig./Img./Abb./Afb./Rys. 10

Fig./Img./Abb./Afb./Rys. 11

Fig./Img./Abb./Afb./Rys. 12

Fig./Img./Abb./Afb./Rys. 13

Fig./Img./Abb./Afb./Rys. 14

Fig./Img./Abb./Afb./Rys. 15

Fig./Img./Abb./Afb./Rys. 16

Fig./Img./Abb./Afb./Rys. 17

Fig./Img./Abb./Afb./Rys. 18

Fig./Img./Abb./Afb./Rys. 19

Fig./Img./Abb./Afb./Rys. 20

Fig./Img./Abb./Afb./Rys. 21

Fig./Img./Abb./Afb./Rys. 22

Fig./Img./Abb./Afb./Rys. 23

Fig./Img./Abb./Afb./Rys. 24

Fig./Img./Abb./Afb./Rys. 25

Fig./Img./Abb./Afb./Rys. 26

www.cecotec.es