TSM1034 - Saw Ferm - Free user manual and instructions
Find the device manual for free TSM1034 Ferm in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product type | Circular saw |
| Brand | Ferm |
| Model | TSM1034 |
| Power | 1200 W |
| Blade diameter | 190 mm |
| No-load speed | 4500 rpm |
| Cutting depth at 90° | 65 mm |
| Cutting depth at 45° | 45 mm |
| Power supply | 230 V / 50 Hz |
| Dimensions (L x W x H) | 300 x 210 x 250 mm |
| Weight | 4.2 kg |
| Main functions | Straight cut, angled cut, parallel guide, dust extraction |
| Angle adjustment | 0° to 45° |
| Parallel guide | Included for precise cuts |
| Vacuum connection | Yes |
| Protective cover | Yes, movable |
| Blade brake | Yes, quick stop |
| Shaft lock | Makes blade changing easier |
| Maintenance and cleaning | Clean the blade and ventilation slots |
| Carbon brush replacement | Possible, brushes accessible |
| Safety | Safety switch, protective cover, insulated handle |
| Spare parts and repairability | Blades, carbon brushes, base plates, guide available |
| General information | 24-month warranty |
Frequently Asked Questions - TSM1034 Ferm
How to change the blade of a Ferm TSM1034 circular saw?
To change the blade, first unplug the device. Use the provided key to lock the shaft via the lock button. Loosen the center screw, remove the used blade and replace it with a new one, respecting the indicated direction of rotation. Tighten the screw firmly and check that the blade rotates freely before using again.
What maximum cutting depth can be achieved with the TSM1034?
The maximum cutting depth is 65 mm when cutting at 90°. At a 45° angle, it is reduced to approximately 45 mm. To adjust the depth, loosen the adjustment lever and adjust the base plate according to the material thickness.
How to adjust the cutting angle on the Ferm TSM1034 saw?
Loosen the angle locking knob located at the front of the base plate. Tilt the base plate to the desired angle (0° to 45°), then tighten the knob. A graduated scale allows precise adjustment. Always check that the blade does not touch the base plate before starting.
How to use the parallel guide provided with the TSM1034?
The parallel guide attaches to each side of the base plate. Insert the rods into the provided holes and tighten the knobs. Position the guide at the desired distance from the cut line to achieve perfectly parallel cuts to the edge of the workpiece.
What to do if the TSM1034 circular saw does not start or starts with difficulty?
First check that the plug is properly connected and that the cable is not damaged. Inspect the motor carbon brushes: if they are worn, replace them. Also make sure that the safety switch is fully pressed. If the problem persists, contact after-sales service.
How to clean the Ferm TSM1034 saw after use?
Unplug the saw before any cleaning. Use a soft brush or cloth to remove sawdust and residues. Clean the blade with a suitable product if necessary. Never use water or aggressive solvents on the motor or electrical parts.
What safety precautions should be taken with the TSM1034?
Always wear protective goggles and a dust mask. Keep your hands away from the blade and use the protective cover. Never remove the cover or safety devices. Make sure the workpiece is securely fixed before cutting. Wait for the blade to come to a complete stop before setting the saw down.
Can I use the TSM1034 circular saw to cut metal?
The saw is designed primarily for wood and wood-based materials. To cut metal, it is necessary to install a suitable special blade, but this can cause premature wear and reduce safety. It is recommended to use a tool designed for metal for frequent work.
How to replace the motor carbon brushes on the TSM1034?
The carbon brushes are located on either side of the motor. Unscrew the protective caps, remove the worn brushes and insert new ones respecting their direction. When the brushes are too short (less than 5 mm), they must be replaced to avoid damaging the commutator.
Where to find spare parts for the TSM1034 model?
You can find spare parts from authorized Ferm dealers or on specialized tool parts websites. Common parts such as blades, carbon brushes, base plates and guides are generally available. Remember to check compatibility with the TSM1034 model.
User questions about TSM1034 Ferm
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Saw in PDF format for free! Find your manual TSM1034 - Ferm and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TSM1034 by Ferm.
USER MANUAL TSM1034 Ferm
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Ferm
Model : TSM1034
Category : Saw